[U-Boot] [PATCH v3 4/6] arm:exynos4:trats: Use pinmux for mmc configuration

[Jaehoon Chung <jh80.chung@samsung.com>]

Acked-by: Jaehoon Chung <jh80.chung@samsung.com>

On 08/29/2012 04:56 PM, Piotr Wilczek wrote:
> This patch use the pinmux for mmc configuration for Trats
> 
> Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> CC: Minkyu Kang <mk7.kang@samsung.com>
> ---
> Changes for v2:
> - mmc initialisation using pinmux
> Changes for v3:
> - init SD card also when eMMC init failed
> 
>  board/samsung/trats/trats.c |   68 +++++++-----------------------------------
>  1 files changed, 12 insertions(+), 56 deletions(-)
> 
> diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
> index f5df56c..84b7430 100644
> --- a/board/samsung/trats/trats.c
> +++ b/board/samsung/trats/trats.c
> @@ -29,6 +29,7 @@
>  #include <asm/arch/cpu.h>
>  #include <asm/arch/gpio.h>
>  #include <asm/arch/mmc.h>
> +#include <asm/arch/pinmux.h>
>  #include <asm/arch/clock.h>
>  #include <asm/arch/clk.h>
>  #include <asm/arch/mipi_dsim.h>
> @@ -140,54 +141,22 @@ int board_mmc_init(bd_t *bis)
>  {
>  	struct exynos4_gpio_part2 *gpio =
>  		(struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
> -	int i, err;
> +	int err;
>  
>  	/* eMMC_EN: SD_0_CDn: GPK0[2] Output High */
>  	s5p_gpio_direction_output(&gpio->k0, 2, 1);
>  	s5p_gpio_set_pull(&gpio->k0, 2, GPIO_PULL_NONE);
>  
>  	/*
> -	 * eMMC GPIO:
> -	 * SDR 8-bit at 48MHz at MMC0
> -	 * GPK0[0]	SD_0_CLK(2)
> -	 * GPK0[1]	SD_0_CMD(2)
> -	 * GPK0[2]	SD_0_CDn	-> Not used
> -	 * GPK0[3:6]	SD_0_DATA[0:3](2)
> -	 * GPK1[3:6]	SD_0_DATA[0:3](3)
> -	 *
> -	 * DDR 4-bit at 26MHz at MMC4
> -	 * GPK0[0]	SD_4_CLK(3)
> -	 * GPK0[1]	SD_4_CMD(3)
> -	 * GPK0[2]	SD_4_CDn	-> Not used
> -	 * GPK0[3:6]	SD_4_DATA[0:3](3)
> -	 * GPK1[3:6]	SD_4_DATA[4:7](4)
> -	 */
> -	for (i = 0; i < 7; i++) {
> -		if (i == 2)
> -			continue;
> -		/* GPK0[0:6] special function 2 */
> -		s5p_gpio_cfg_pin(&gpio->k0, i, 0x2);
> -		/* GPK0[0:6] pull disable */
> -		s5p_gpio_set_pull(&gpio->k0, i, GPIO_PULL_NONE);
> -		/* GPK0[0:6] drv 4x */
> -		s5p_gpio_set_drv(&gpio->k0, i, GPIO_DRV_4X);
> -	}
> -
> -	for (i = 3; i < 7; i++) {
> -		/* GPK1[3:6] special function 3 */
> -		s5p_gpio_cfg_pin(&gpio->k1, i, 0x3);
> -		/* GPK1[3:6] pull disable */
> -		s5p_gpio_set_pull(&gpio->k1, i, GPIO_PULL_NONE);
> -		/* GPK1[3:6] drv 4x */
> -		s5p_gpio_set_drv(&gpio->k1, i, GPIO_DRV_4X);
> -	}
> -
> -	/*
>  	 * MMC device init
>  	 * mmc0	 : eMMC (8-bit buswidth)
>  	 * mmc2	 : SD card (4-bit buswidth)
>  	 */
> -	err = s5p_mmc_init(0, 8);
> +	err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE);
> +	if (err)
> +		debug("SDMMC0 not configured\n");
> +	else
> +		err = s5p_mmc_init(0, 8);
>  
>  	/* T-flash detect */
>  	s5p_gpio_cfg_pin(&gpio->x3, 4, 0xf);
> @@ -198,24 +167,11 @@ int board_mmc_init(bd_t *bis)
>  	 * GPX3[4] T-flash detect pin
>  	 */
>  	if (!s5p_gpio_get_value(&gpio->x3, 4)) {
> -		/*
> -		 * SD card GPIO:
> -		 * GPK2[0]	SD_2_CLK(2)
> -		 * GPK2[1]	SD_2_CMD(2)
> -		 * GPK2[2]	SD_2_CDn	-> Not used
> -		 * GPK2[3:6]	SD_2_DATA[0:3](2)
> -		 */
> -		for (i = 0; i < 7; i++) {
> -			if (i == 2)
> -				continue;
> -			/* GPK2[0:6] special function 2 */
> -			s5p_gpio_cfg_pin(&gpio->k2, i, 0x2);
> -			/* GPK2[0:6] pull disable */
> -			s5p_gpio_set_pull(&gpio->k2, i, GPIO_PULL_NONE);
> -			/* GPK2[0:6] drv 4x */
> -			s5p_gpio_set_drv(&gpio->k2, i, GPIO_DRV_4X);
> -		}
> -		err = s5p_mmc_init(2, 4);
> +		err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE);
> +		if (err)
> +			debug("SDMMC2 not configured\n");
> +		else
> +			err = s5p_mmc_init(2, 4);
>  	}
>  
>  	return err;
>