From: Stefano Babic <sbabic@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH V3 0/9] separate miiphy from ethernet
Date: Sat, 10 Nov 2012 08:28:18 +0100 [thread overview]
Message-ID: <509E0212.3010609@denx.de> (raw)
In-Reply-To: <1350960047-23404-1-git-send-email-troy.kisky@boundarydevices.com>
On 23/10/2012 04:40, Troy Kisky wrote:
> This series tries to separate the mii regsisters
> from the ethernet registers as suggested by
> Andy Fleming. Then, mx6qsabrelite is changed
> to find the phy address from the possibles 4-7.
>
> The V3 series is very different from V2.
>
> Troy Kisky (9):
> doc/README.fec_mxc: add documentation
> net: fec_mxc: delete CONFIG_FEC_MXC_MULTI
> net: fec_mxc: change fec_mii_setspeed parameter
> net: fec_mxc: have fecmxc_initialize call fecmxc_initialize_multi
> phy: add phy_find_by_mask/phy_connect_dev
> net: fec_mxc: use fec_set_dev_name to set name
> net: fec_mxc: only call phy_connect in fec_probe
> net: fec_mxc: get phydev before fec_probe
> mx6qsabrelite: search mii phy address 4-7
>
Hi Joe,
> board/freescale/mx6qsabrelite/mx6qsabrelite.c | 24 +++-
> doc/README.fec_mxc | 27 ++++
> drivers/net/fec_mxc.c | 164 ++++++++++++++-----------
> drivers/net/fec_mxc.h | 2 +-
> drivers/net/phy/phy.c | 128 +++++++++++--------
> include/configs/m28evk.h | 1 -
> include/configs/mx28evk.h | 1 -
> include/configs/sc_sps_1.h | 1 -
> include/netdev.h | 7 ++
> include/phy.h | 3 +
> 10 files changed, 227 insertions(+), 131 deletions(-)
> create mode 100644 doc/README.fec_mxc
Patches are assigned to me in patchworks. Do you have any issue with
this patchset ? If it is ok for you, I will apply it to u-boot-imx.
Best regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
next prev parent reply other threads:[~2012-11-10 7:28 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-08-20 22:48 [U-Boot] [PATCH V1 1/3] phy: add phy_connect_by_mask Troy Kisky
2012-08-20 22:48 ` [U-Boot] [PATCH V1 2/3] fec_mxc: use phy_connect_by_mask Troy Kisky
2012-08-20 22:48 ` [U-Boot] [PATCH V1 3/3] mx6qsabrelite: set CONFIG_FEC_MXC_PHYMASK Troy Kisky
2012-08-20 23:07 ` [U-Boot] [PATCH V1 1/3] phy: add phy_connect_by_mask Troy Kisky
2012-08-21 0:35 ` Andy Fleming
2012-08-22 19:59 ` Troy Kisky
2012-08-22 20:40 ` Andy Fleming
2012-08-22 20:50 ` Joe Hershberger
2012-08-22 21:21 ` Troy Kisky
2012-09-26 17:26 ` Joe Hershberger
2012-09-26 17:47 ` Troy Kisky
2012-08-22 20:11 ` Eric Nelson
2012-08-22 20:50 ` Andy Fleming
2012-08-22 20:56 ` Eric Nelson
2012-10-23 2:40 ` [U-Boot] [PATCH V3 0/9] separate miiphy from ethernet Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 1/9] doc/README.fec_mxc: add documentation Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 2/9] net: fec_mxc: delete CONFIG_FEC_MXC_MULTI Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 3/9] net: fec_mxc: change fec_mii_setspeed parameter Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 4/9] net: fec_mxc: have fecmxc_initialize call fecmxc_initialize_multi Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 5/9] phy: add phy_find_by_mask/phy_connect_dev Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 6/9] net: fec_mxc: use fec_set_dev_name to set name Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 7/9] net: fec_mxc: only call phy_connect in fec_probe Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 8/9] net: fec_mxc: get phydev before fec_probe Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 9/9] mx6qsabrelite: search mii phy address 4-7 Troy Kisky
2012-11-10 7:28 ` Stefano Babic [this message]
2013-01-22 23:48 ` [U-Boot] [PATCH V3 0/9] separate miiphy from ethernet Troy Kisky
2013-01-23 8:48 ` Stefano Babic
2013-01-23 19:06 ` Troy Kisky
2013-01-24 9:09 ` Stefano Babic
2013-01-23 22:35 ` Troy Kisky
2013-01-03 22:00 ` Troy Kisky
2013-01-28 6:00 ` Stefano Babic
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=509E0212.3010609@denx.de \
--to=sbabic@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox