* [U-Boot] [PATCH 0/4] apf27: add support of armadeus apf27 v2
@ 2012-10-29 17:35 Philippe Reynes
2012-10-29 17:35 ` [U-Boot] [PATCH 1/4] apf27: add missing constant to mx27 Philippe Reynes
` (3 more replies)
0 siblings, 4 replies; 10+ messages in thread
From: Philippe Reynes @ 2012-10-29 17:35 UTC (permalink / raw)
To: u-boot
Difference between v1 and v2:
- use spl instead of nand_spl
- use gpio api
- remove use of useless CONFIG_SYS
- remove use of config.mk
- remove dead code
Philippe Reynes (4):
apf27: add missing constant to mx27
apf27: add support for the armadeus APF27 board
apf27: add spl support for the apf27
apf27: add FPGA support for the apf27 board
MAINTAINERS | 5 +
arch/arm/cpu/arm926ejs/mx27/asm-offsets.c | 34 ++
arch/arm/include/asm/arch-mx27/imx-regs.h | 11 +-
arch/arm/include/asm/arch-mx27/mxc_nand.h | 83 +++++
board/armadeus/apf27/Makefile | 51 +++
board/armadeus/apf27/apf27.c | 424 ++++++++++++++++++++++
board/armadeus/apf27/apf27.h | 477 +++++++++++++++++++++++++
board/armadeus/apf27/fpga.c | 262 ++++++++++++++
board/armadeus/apf27/fpga.h | 39 ++
board/armadeus/apf27/start.S | 549 +++++++++++++++++++++++++++++
board/armadeus/apf27/u-boot-spl.lds | 87 +++++
boards.cfg | 1 +
include/configs/apf27.h | 458 ++++++++++++++++++++++++
13 files changed, 2480 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/include/asm/arch-mx27/mxc_nand.h
create mode 100644 board/armadeus/apf27/Makefile
create mode 100644 board/armadeus/apf27/apf27.c
create mode 100644 board/armadeus/apf27/apf27.h
create mode 100644 board/armadeus/apf27/fpga.c
create mode 100644 board/armadeus/apf27/fpga.h
create mode 100644 board/armadeus/apf27/start.S
create mode 100644 board/armadeus/apf27/u-boot-spl.lds
create mode 100644 include/configs/apf27.h
--
1.7.4.4
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 1/4] apf27: add missing constant to mx27
2012-10-29 17:35 [U-Boot] [PATCH 0/4] apf27: add support of armadeus apf27 v2 Philippe Reynes
@ 2012-10-29 17:35 ` Philippe Reynes
2012-10-29 17:35 ` [U-Boot] [PATCH 2/4] apf27: add support for the armadeus APF27 board Philippe Reynes
` (2 subsequent siblings)
3 siblings, 0 replies; 10+ messages in thread
From: Philippe Reynes @ 2012-10-29 17:35 UTC (permalink / raw)
To: u-boot
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
create mode 100644 arch/arm/include/asm/arch-mx27/mxc_nand.h
diff --git a/arch/arm/cpu/arm926ejs/mx27/asm-offsets.c b/arch/arm/cpu/arm926ejs/mx27/asm-offsets.c
index f3a8d7b..b95c58c 100644
--- a/arch/arm/cpu/arm926ejs/mx27/asm-offsets.c
+++ b/arch/arm/cpu/arm926ejs/mx27/asm-offsets.c
@@ -34,6 +34,7 @@ int main(void)
DEFINE(PCDR1, IMX_PLL_BASE + offsetof(struct pll_regs, pcdr1));
DEFINE(PCCR0, IMX_PLL_BASE + offsetof(struct pll_regs, pccr0));
DEFINE(PCCR1, IMX_PLL_BASE + offsetof(struct pll_regs, pccr1));
+ DEFINE(CCSR, IMX_PLL_BASE + offsetof(struct pll_regs, ccsr));
DEFINE(ESDCTL0_ROF, offsetof(struct esdramc_regs, esdctl0));
DEFINE(ESDCFG0_ROF, offsetof(struct esdramc_regs, esdcfg0));
@@ -41,5 +42,38 @@ int main(void)
DEFINE(ESDCFG1_ROF, offsetof(struct esdramc_regs, esdcfg1));
DEFINE(ESDMISC_ROF, offsetof(struct esdramc_regs, esdmisc));
+ DEFINE(GPCR, IMX_SYSTEM_CTL_BASE +
+ offsetof(struct system_control_regs, gpcr));
+ DEFINE(FMCR, IMX_SYSTEM_CTL_BASE +
+ offsetof(struct system_control_regs, fmcr));
+ DEFINE(DSCR2, IMX_SYSTEM_CTL_BASE +
+ offsetof(struct system_control_regs, dscr2));
+ DEFINE(DSCR3, IMX_SYSTEM_CTL_BASE +
+ offsetof(struct system_control_regs, dscr3));
+ DEFINE(DSCR7, IMX_SYSTEM_CTL_BASE +
+ offsetof(struct system_control_regs, dscr7));
+ DEFINE(DSCR10, IMX_SYSTEM_CTL_BASE +
+ offsetof(struct system_control_regs, dscr10));
+
+ DEFINE(CS0U, IMX_WEIM_BASE + offsetof(struct weim_regs, cs0u));
+ DEFINE(CS0L, IMX_WEIM_BASE + offsetof(struct weim_regs, cs0l));
+ DEFINE(CS0A, IMX_WEIM_BASE + offsetof(struct weim_regs, cs0a));
+ DEFINE(CS1U, IMX_WEIM_BASE + offsetof(struct weim_regs, cs1u));
+ DEFINE(CS1L, IMX_WEIM_BASE + offsetof(struct weim_regs, cs1l));
+ DEFINE(CS1A, IMX_WEIM_BASE + offsetof(struct weim_regs, cs1a));
+ DEFINE(CS2U, IMX_WEIM_BASE + offsetof(struct weim_regs, cs2u));
+ DEFINE(CS2L, IMX_WEIM_BASE + offsetof(struct weim_regs, cs2l));
+ DEFINE(CS2A, IMX_WEIM_BASE + offsetof(struct weim_regs, cs2a));
+ DEFINE(CS3U, IMX_WEIM_BASE + offsetof(struct weim_regs, cs3u));
+ DEFINE(CS3L, IMX_WEIM_BASE + offsetof(struct weim_regs, cs3l));
+ DEFINE(CS3A, IMX_WEIM_BASE + offsetof(struct weim_regs, cs3a));
+ DEFINE(CS4U, IMX_WEIM_BASE + offsetof(struct weim_regs, cs4u));
+ DEFINE(CS4L, IMX_WEIM_BASE + offsetof(struct weim_regs, cs4l));
+ DEFINE(CS4A, IMX_WEIM_BASE + offsetof(struct weim_regs, cs4a));
+ DEFINE(CS5U, IMX_WEIM_BASE + offsetof(struct weim_regs, cs5u));
+ DEFINE(CS5L, IMX_WEIM_BASE + offsetof(struct weim_regs, cs5l));
+ DEFINE(CS5A, IMX_WEIM_BASE + offsetof(struct weim_regs, cs5a));
+ DEFINE(EIM, IMX_WEIM_BASE + offsetof(struct weim_regs, eim));
+
return 0;
}
diff --git a/arch/arm/include/asm/arch-mx27/imx-regs.h b/arch/arm/include/asm/arch-mx27/imx-regs.h
index 2f6c823..d3a14e1 100644
--- a/arch/arm/include/asm/arch-mx27/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx27/imx-regs.h
@@ -185,7 +185,7 @@ struct iim_regs {
struct fuse_bank {
u32 fuse_regs[0x20];
u32 fuse_rsvd[0xe0];
- } bank[1];
+ } bank[2];
};
struct fuse_bank0_regs {
@@ -511,4 +511,13 @@ struct fuse_bank0_regs {
#define IIM_ERR_SNSE (1 << 2)
#define IIM_ERR_PARITYE (1 << 1)
+/*
+ * Memory areas of the NFC
+ */
+#define IMX_NFC_BASE (0xD8000000)
+#define IMX_NFC_MAIN_AREA0 (0xD8000000)
+#define IMX_NFC_MAIN_AREA1 (0xD8000200)
+#define IMX_NFC_SPARE_AREA0 (0xD8000800)
+#define IMX_NFC_REGS (0xD8000E00)
+
#endif /* _IMX_REGS_H */
diff --git a/arch/arm/include/asm/arch-mx27/mxc_nand.h b/arch/arm/include/asm/arch-mx27/mxc_nand.h
new file mode 100644
index 0000000..3429601
--- /dev/null
+++ b/arch/arm/include/asm/arch-mx27/mxc_nand.h
@@ -0,0 +1,83 @@
+/*
+ * (c) 2012 Philippe Reynes <tremyfr@yahoo.fr>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __MXC_NAND_H
+#define __MXC_NAND_H
+
+/*
+ * NFC registers address offest
+ */
+#define NFC_OFFSET_BUFSIZE (0x00) /* Internal SRAM Size */
+#define NFC_OFFSET_BLCK_ADD_LOCK (0x02) /* NAND Flash Block Address for
+ Lock Check */
+#define NFC_OFFSET_BUF_ADDR (0x04) /* Buffer Number for Page Data
+ Transfer To/From Flash Mem */
+#define NFC_OFFSET_FLASH_ADDR (0x06) /* NAND Flash Address */
+#define NFC_OFFSET_FLASH_CMD (0x08) /* NAND Flash Command */
+#define NFC_OFFSET_CONFIG (0x0A) /* NFC Internal Buffer Lock
+ Control */
+#define NFC_OFFSET_ECC_STATUS_RESULT (0x0C) /* Controller Status/Result of
+ Flash Operation */
+#define NFC_OFFSET_ECC_RSLT_MAIN_AREA (0x0E) /* ECC Error Position of Main
+ Area Data Error */
+#define NFC_OFFSET_ECC_RSLT_SPARE_AREA (0x10) /* ECC Error Position of Spare
+ Area Data Error */
+#define NFC_OFFSET_WRPROT (0x12) /* Nand Flash Write Protection */
+#define NFC_OFFSET_UNLOCKSTART_BLKADDR (0x14) /* Start Address for Write
+ Protection Unlock */
+#define NFC_OFFSET_UNLOCKEND_BLKADDR (0x16) /* End Address for Write
+ Protection Unlock */
+#define NFC_OFFSET_WRPR_STAT (0x18) /* Current Nand Flash Write
+ Protection Status */
+#define NFC_OFFSET_CONFIG1 (0x1A) /* Nand Flash Operation
+ Configuration 1 */
+#define NFC_OFFSET_CONFIG2 (0x1C) /* Nand Flash Operation
+ Configuration 2 */
+
+/* NFC_ECC_STATUS_RESULT Status Register Bit Fields */
+#define NFC_ECC_STAT_ERM_SHFT (2) /* ERM shift */
+#define NFC_ECC_STAT_ERS_MASK (0x03) /* ERS mask */
+#define NFC_ECC_STAT_ERROR1 (1<<0) /* correctable error */
+#define NFC_ECC_STAT_ERROR2 (1<<1) /* non correctable error */
+
+/* NFC_CONFIG Control Register Bit Fields */
+#define NFC_CONFIG_UNLOCKED (1<<1) /* unlocked */
+#define NFC_CONFIG_LOCKED (1<<0) /* locked */
+
+/* NFC_CONFIG1 Control Register Bit Fields */
+#define NFC_CONFIG1_CEn (1<<7) /* Flash force CE */
+#define NFC_CONFIG1_RST (1<<6) /* Reset */
+#define NFC_CONFIG1_BIG (1<<5) /* Big Endian Mode */
+#define NFC_CONFIG1_INT_MSK (1<<4) /* Mask Interrupt Bit */
+#define NFC_CONFIG1_ECC_EN (1<<3) /* ECC operation enable */
+#define NFC_CONFIG1_SP_EN (1<<2) /* Flash spare enable */
+
+/* NFC_CONFIG2 Control Register Bit Fields */
+#define NFC_CONFIG2_INT (1<<15) /* Interrupt */
+#define NFC_CONFIG2_FDO_STATUS (4<<3) /* Flash status output */
+#define NFC_CONFIG2_FDO_ID (2<<3) /* Flash ID output */
+#define NFC_CONFIG2_FDO_PAGE (1<<3) /* Flash data output */
+#define NFC_CONFIG2_FDI (1<<2) /* Flash data input */
+#define NFC_CONFIG2_FADD (1<<1) /* Flash address input */
+#define NFC_CONFIG2_FCMD (1<<0) /* Flash command input */
+
+#endif
--
1.7.4.4
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 2/4] apf27: add support for the armadeus APF27 board
2012-10-29 17:35 [U-Boot] [PATCH 0/4] apf27: add support of armadeus apf27 v2 Philippe Reynes
2012-10-29 17:35 ` [U-Boot] [PATCH 1/4] apf27: add missing constant to mx27 Philippe Reynes
@ 2012-10-29 17:35 ` Philippe Reynes
2012-11-26 17:55 ` Albert ARIBAUD
2012-10-29 17:35 ` [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27 Philippe Reynes
2012-10-29 17:35 ` [U-Boot] [PATCH 4/4] apf27: add FPGA support for the apf27 board Philippe Reynes
3 siblings, 1 reply; 10+ messages in thread
From: Philippe Reynes @ 2012-10-29 17:35 UTC (permalink / raw)
To: u-boot
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
create mode 100644 board/armadeus/apf27/Makefile
create mode 100644 board/armadeus/apf27/apf27.c
create mode 100644 board/armadeus/apf27/apf27.h
create mode 100644 include/configs/apf27.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 1b2da94..297467a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1011,6 +1011,11 @@ Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
armadillo-800eva R8A7740 (RMOBILE SoC)
+Eric Jarrige <eric.jarrige@armadeus.org>
+Philippe Reynes <tremyfr@yahoo.fr>
+
+ apf27 ARM926EJS (imx27 SoC)
+
-------------------------------------------------------------------------
Unknown / orphaned boards:
diff --git a/board/armadeus/apf27/Makefile b/board/armadeus/apf27/Makefile
new file mode 100644
index 0000000..1da9548
--- /dev/null
+++ b/board/armadeus/apf27/Makefile
@@ -0,0 +1,45 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+# (C) Copyright 2012
+# Eric Jarrige <eric.jarrige@armadeus.org>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := apf27.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/armadeus/apf27/apf27.c b/board/armadeus/apf27/apf27.c
new file mode 100644
index 0000000..4f2b821
--- /dev/null
+++ b/board/armadeus/apf27/apf27.c
@@ -0,0 +1,408 @@
+/*
+ * Copyright (C) 2007 Sascha Hauer, Pengutronix
+ * Copyright (C) 2008-2012 Eric Jarrige <eric.jarrige@armadeus.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include "crc.h"
+#include <jffs2/jffs2.h>
+#include <nand.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/gpio.h>
+#include <asm/errno.h>
+#include <environment.h>
+#include "apf27.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Fuse bank 1 row 8 is "reserved for future use" and therefore available for
+ * custormer use. The APF27 board uses this fuse to store the board revision:
+ * 0: initial board revision
+ * 1: first revision - Presence of the second RAM chip on the board is blown in
+ * fuse bank 1 row 9 bit 0 - No hardware change
+ * N: to be defined
+ */
+u32 get_board_rev(void)
+{
+ struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
+
+ return readl(&iim->bank[1].fuse_regs[8]);
+}
+
+/*
+ * Fuse bank 1 row 9 is "reserved for future use" and therefore available for
+ * custormer use. The APF27 board revision 1 uses the bit 0 to permanently store
+ * the presence of the second RAM chip
+ * 0: AFP27 with 1 RAM of 64 MiB
+ * 1: AFP27 with 2 RAM chips of 64 MiB each (128MB)
+ */
+int get_num_ram_bank(void)
+{
+ struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
+ int nr_dram_banks = 1;
+
+ if ((get_board_rev() > 0) && (CONFIG_NR_DRAM_BANKS > 1))
+ nr_dram_banks += readl(&iim->bank[1].fuse_regs[9]) & 0x01;
+ else
+ nr_dram_banks = CONFIG_NR_DRAM_POPULATED;
+
+ return nr_dram_banks;
+}
+
+static void apf27_gpio_init(void)
+{
+ struct gpio_port_regs *regs = (struct gpio_port_regs *)IMX_GPIO_BASE;
+
+ /* PORT A */
+ writel(ACFG_DR_A_VAL, ®s->port[PORTA].gpio_dr);
+ writel(ACFG_OCR1_A_VAL, ®s->port[PORTA].ocr1);
+ writel(ACFG_OCR2_A_VAL, ®s->port[PORTA].ocr2);
+ writel(ACFG_ICFA1_A_VAL, ®s->port[PORTA].iconfa1);
+ writel(ACFG_ICFA2_A_VAL, ®s->port[PORTA].iconfa2);
+ writel(ACFG_ICFB1_A_VAL, ®s->port[PORTA].iconfb1);
+ writel(ACFG_ICFB2_A_VAL, ®s->port[PORTA].iconfb2);
+ writel(ACFG_ICR1_A_VAL, ®s->port[PORTA].icr1);
+ writel(ACFG_ICR2_A_VAL, ®s->port[PORTA].icr2);
+ writel(ACFG_IMR_A_VAL, ®s->port[PORTA].imr);
+ writel(ACFG_DDIR_A_VAL, ®s->port[PORTA].gpio_dir);
+ writel(ACFG_GPR_A_VAL, ®s->port[PORTA].gpr);
+ writel(ACFG_PUEN_A_VAL, ®s->port[PORTA].puen);
+ writel(ACFG_GIUS_A_VAL, ®s->port[PORTA].gius);
+
+ /* PORT B */
+ writel(ACFG_DR_B_VAL, ®s->port[PORTB].gpio_dr);
+ writel(ACFG_OCR1_B_VAL, ®s->port[PORTB].ocr1);
+ writel(ACFG_OCR2_B_VAL, ®s->port[PORTB].ocr2);
+ writel(ACFG_ICFA1_B_VAL, ®s->port[PORTB].iconfa1);
+ writel(ACFG_ICFA2_B_VAL, ®s->port[PORTB].iconfa2);
+ writel(ACFG_ICFB1_B_VAL, ®s->port[PORTB].iconfb1);
+ writel(ACFG_ICFB2_B_VAL, ®s->port[PORTB].iconfb2);
+ writel(ACFG_ICR1_B_VAL, ®s->port[PORTB].icr1);
+ writel(ACFG_ICR2_B_VAL, ®s->port[PORTB].icr2);
+ writel(ACFG_IMR_B_VAL, ®s->port[PORTB].imr);
+ writel(ACFG_DDIR_B_VAL, ®s->port[PORTB].gpio_dir);
+ writel(ACFG_GPR_B_VAL, ®s->port[PORTB].gpr);
+ writel(ACFG_PUEN_B_VAL, ®s->port[PORTB].puen);
+ writel(ACFG_GIUS_B_VAL, ®s->port[PORTB].gius);
+
+ /* PORT C */
+ writel(ACFG_DR_C_VAL, ®s->port[PORTC].gpio_dr);
+ writel(ACFG_OCR1_C_VAL, ®s->port[PORTC].ocr1);
+ writel(ACFG_OCR2_C_VAL, ®s->port[PORTC].ocr2);
+ writel(ACFG_ICFA1_C_VAL, ®s->port[PORTC].iconfa1);
+ writel(ACFG_ICFA2_C_VAL, ®s->port[PORTC].iconfa2);
+ writel(ACFG_ICFB1_C_VAL, ®s->port[PORTC].iconfb1);
+ writel(ACFG_ICFB2_C_VAL, ®s->port[PORTC].iconfb2);
+ writel(ACFG_ICR1_C_VAL, ®s->port[PORTC].icr1);
+ writel(ACFG_ICR2_C_VAL, ®s->port[PORTC].icr2);
+ writel(ACFG_IMR_C_VAL, ®s->port[PORTC].imr);
+ writel(ACFG_DDIR_C_VAL, ®s->port[PORTC].gpio_dir);
+ writel(ACFG_GPR_C_VAL, ®s->port[PORTC].gpr);
+ writel(ACFG_PUEN_C_VAL, ®s->port[PORTC].puen);
+ writel(ACFG_GIUS_C_VAL, ®s->port[PORTC].gius);
+
+ /* PORT D */
+ writel(ACFG_DR_D_VAL, ®s->port[PORTD].gpio_dr);
+ writel(ACFG_OCR1_D_VAL, ®s->port[PORTD].ocr1);
+ writel(ACFG_OCR2_D_VAL, ®s->port[PORTD].ocr2);
+ writel(ACFG_ICFA1_D_VAL, ®s->port[PORTD].iconfa1);
+ writel(ACFG_ICFA2_D_VAL, ®s->port[PORTD].iconfa2);
+ writel(ACFG_ICFB1_D_VAL, ®s->port[PORTD].iconfb1);
+ writel(ACFG_ICFB2_D_VAL, ®s->port[PORTD].iconfb2);
+ writel(ACFG_ICR1_D_VAL, ®s->port[PORTD].icr1);
+ writel(ACFG_ICR2_D_VAL, ®s->port[PORTD].icr2);
+ writel(ACFG_IMR_D_VAL, ®s->port[PORTD].imr);
+ writel(ACFG_DDIR_D_VAL, ®s->port[PORTD].gpio_dir);
+ writel(ACFG_GPR_D_VAL, ®s->port[PORTD].gpr);
+ writel(ACFG_PUEN_D_VAL, ®s->port[PORTD].puen);
+ writel(ACFG_GIUS_D_VAL, ®s->port[PORTD].gius);
+
+ /* PORT E */
+ writel(ACFG_DR_E_VAL, ®s->port[PORTE].gpio_dr);
+ writel(ACFG_OCR1_E_VAL, ®s->port[PORTE].ocr1);
+ writel(ACFG_OCR2_E_VAL, ®s->port[PORTE].ocr2);
+ writel(ACFG_ICFA1_E_VAL, ®s->port[PORTE].iconfa1);
+ writel(ACFG_ICFA2_E_VAL, ®s->port[PORTE].iconfa2);
+ writel(ACFG_ICFB1_E_VAL, ®s->port[PORTE].iconfb1);
+ writel(ACFG_ICFB2_E_VAL, ®s->port[PORTE].iconfb2);
+ writel(ACFG_ICR1_E_VAL, ®s->port[PORTE].icr1);
+ writel(ACFG_ICR2_E_VAL, ®s->port[PORTE].icr2);
+ writel(ACFG_IMR_E_VAL, ®s->port[PORTE].imr);
+ writel(ACFG_DDIR_E_VAL, ®s->port[PORTE].gpio_dir);
+ writel(ACFG_GPR_E_VAL, ®s->port[PORTE].gpr);
+ writel(ACFG_PUEN_E_VAL, ®s->port[PORTE].puen);
+ writel(ACFG_GIUS_E_VAL, ®s->port[PORTE].gius);
+
+ /* PORT F */
+ writel(ACFG_DR_F_VAL, ®s->port[PORTF].gpio_dr);
+ writel(ACFG_OCR1_F_VAL, ®s->port[PORTF].ocr1);
+ writel(ACFG_OCR2_F_VAL, ®s->port[PORTF].ocr2);
+ writel(ACFG_ICFA1_F_VAL, ®s->port[PORTF].iconfa1);
+ writel(ACFG_ICFA2_F_VAL, ®s->port[PORTF].iconfa2);
+ writel(ACFG_ICFB1_F_VAL, ®s->port[PORTF].iconfb1);
+ writel(ACFG_ICFB2_F_VAL, ®s->port[PORTF].iconfb2);
+ writel(ACFG_ICR1_F_VAL, ®s->port[PORTF].icr1);
+ writel(ACFG_ICR2_F_VAL, ®s->port[PORTF].icr2);
+ writel(ACFG_IMR_F_VAL, ®s->port[PORTF].imr);
+ writel(ACFG_DDIR_F_VAL, ®s->port[PORTF].gpio_dir);
+ writel(ACFG_GPR_F_VAL, ®s->port[PORTF].gpr);
+ writel(ACFG_PUEN_F_VAL, ®s->port[PORTF].puen);
+ writel(ACFG_GIUS_F_VAL, ®s->port[PORTF].gius);
+}
+
+static int apf27_devices_init(void)
+{
+ struct gpio_port_regs *regs = (struct gpio_port_regs *)IMX_GPIO_BASE;
+ int i;
+ unsigned int mode[] = {
+ PD0_AIN_FEC_TXD0,
+ PD1_AIN_FEC_TXD1,
+ PD2_AIN_FEC_TXD2,
+ PD3_AIN_FEC_TXD3,
+ PD4_AOUT_FEC_RX_ER,
+ PD5_AOUT_FEC_RXD1,
+ PD6_AOUT_FEC_RXD2,
+ PD7_AOUT_FEC_RXD3,
+ PD8_AF_FEC_MDIO,
+ PD9_AIN_FEC_MDC | GPIO_PUEN,
+ PD10_AOUT_FEC_CRS,
+ PD11_AOUT_FEC_TX_CLK,
+ PD12_AOUT_FEC_RXD0,
+ PD13_AOUT_FEC_RX_DV,
+ PD14_AOUT_FEC_CLR,
+ PD15_AOUT_FEC_COL,
+ PD16_AIN_FEC_TX_ER,
+ PF23_AIN_FEC_TX_EN,
+ PE12_PF_UART1_TXD,
+ PE13_PF_UART1_RXD,
+ };
+
+ for (i = 0; i < ARRAY_SIZE(mode); i++)
+ imx_gpio_mode(mode[i]);
+
+#ifdef CONFIG_MXC_MMC
+ mx27_sd2_init_pins();
+ imx_gpio_mode((GPIO_PORTF | GPIO_OUT | GPIO_PUEN | GPIO_GPIO | 16));
+ writel(readl(®s->port[PORTF].gpio_dr) | (1 << 16),
+ ®s->port[PORTF].gpio_dr);
+#endif
+ return 0;
+}
+
+static void board_setup_aipi(void)
+{
+ struct aipi_regs *aipi1 = (struct aipi_regs *)IMX_AIPI1_BASE;
+ struct aipi_regs *aipi2 = (struct aipi_regs *)IMX_AIPI2_BASE;
+ struct system_control_regs *system = \
+ (struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
+ u32 gpcr;
+
+ /* setup AIPI1 and AIPI2 */
+ writel(ACFG_AIPI1_PSR0_VAL, &aipi1->psr0);
+ writel(ACFG_AIPI1_PSR1_VAL, &aipi1->psr1);
+ writel(ACFG_AIPI2_PSR0_VAL, &aipi2->psr0);
+ writel(ACFG_AIPI2_PSR1_VAL, &aipi2->psr1);
+
+ /* Change SDRAM signal strengh */
+ gpcr = readl(&system->gpcr);
+ gpcr |= ACFG_GPCR_VAL;
+ writel(gpcr, &system->gpcr);
+}
+
+static void board_setup_csx(void)
+{
+ struct weim_regs *weim = (struct weim_regs *)IMX_WEIM_BASE;
+
+ writel(ACFG_CS0U_VAL, &weim->cs0u);
+ writel(ACFG_CS0L_VAL, &weim->cs0l);
+ writel(ACFG_CS0A_VAL, &weim->cs0a);
+
+ writel(ACFG_CS1U_VAL, &weim->cs1u);
+ writel(ACFG_CS1L_VAL, &weim->cs1l);
+ writel(ACFG_CS1A_VAL, &weim->cs1a);
+
+ writel(ACFG_CS2U_VAL, &weim->cs2u);
+ writel(ACFG_CS2L_VAL, &weim->cs2l);
+ writel(ACFG_CS2A_VAL, &weim->cs2a);
+
+ writel(ACFG_CS3U_VAL, &weim->cs3u);
+ writel(ACFG_CS3L_VAL, &weim->cs3l);
+ writel(ACFG_CS3A_VAL, &weim->cs3a);
+
+ writel(ACFG_CS4U_VAL, &weim->cs4u);
+ writel(ACFG_CS4L_VAL, &weim->cs4l);
+ writel(ACFG_CS4A_VAL, &weim->cs4a);
+
+ writel(ACFG_CS5U_VAL, &weim->cs5u);
+ writel(ACFG_CS5L_VAL, &weim->cs5l);
+ writel(ACFG_CS5A_VAL, &weim->cs5a);
+
+ writel(ACFG_EIM_VAL, &weim->eim);
+}
+
+static void board_setup_port(void)
+{
+ struct system_control_regs *system = \
+ (struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
+
+ writel(ACFG_FMCR_VAL, &system->fmcr);
+}
+
+static void board_setup_clock()
+{
+ struct pll_regs *pll = (struct pll_regs *)IMX_PLL_BASE;
+ volatile int wait = 0x1000;
+ u32 cscr;
+
+ /* disable MPLL/SPLL first */
+ cscr = readl(&pll->cscr);
+ cscr &= ~(CSCR_MPEN|CSCR_SPEN);
+ writel(cscr, &pll->cscr);
+
+ /* pll clock initialization */
+ writel(ACFG_MPCTL0_VAL, &pll->mpctl0);
+ writel(ACFG_SPCTL0_VAL, &pll->spctl0);
+
+ cscr = ACFG_CSCR_VAL|CSCR_MPLL_RESTART|CSCR_SPLL_RESTART;
+ writel(cscr, &pll->cscr);
+
+ /* add some delay here */
+ while (wait)
+ wait--;
+
+ /* peripheral clock divider */
+ writel(ACFG_PCDR0_VAL, &pll->pcdr0);
+ writel(ACFG_PCDR1_VAL, &pll->pcdr1);
+
+ /* Configure PCCR0 and PCCR1 */
+ writel(ACFG_PCCR0_VAL, &pll->pccr0);
+ writel(ACFG_PCCR1_VAL, &pll->pccr1);
+}
+
+int board_early_init_f(void)
+{
+ board_setup_aipi();
+ board_setup_csx();
+ board_setup_port();
+ board_setup_clock();
+
+ return 0;
+}
+
+int
+board_init(void)
+{
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ apf27_gpio_init();
+ apf27_devices_init();
+
+ return 0;
+}
+
+int
+dram_init(void)
+{
+ /* dram_init must store complete ramsize in gd->ram_size */
+ if (get_num_ram_bank() > 1) {
+ gd->ram_size = PHYS_SDRAM_2 - CONFIG_SYS_SDRAM_BASE
+ + get_ram_size((void *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE);
+ } else {
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1,
+ PHYS_SDRAM_1_SIZE);
+ }
+
+ return 0;
+}
+
+void dram_init_banksize(void)
+{
+ phys_size_t ramsize = gd->ram_size;
+
+ if (get_num_ram_bank() > 1)
+ ramsize -= PHYS_SDRAM_2 - CONFIG_SYS_SDRAM_BASE;
+
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = ramsize;
+ gd->ram_size = gd->bd->bi_dram[0].size;
+
+ if (CONFIG_NR_DRAM_BANKS > 1) {
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ if (get_num_ram_bank() > 1)
+ gd->bd->bi_dram[1].size = ramsize;
+ else
+ gd->bd->bi_dram[1].size = 0;
+ gd->ram_size += gd->bd->bi_dram[1].size;
+ }
+}
+
+/*
+ * Miscellaneous intialization
+ */
+int
+misc_init_r(void)
+{
+ char *s;
+ u_char * firmware_buffer = (u_char *)(CONFIG_SYS_LOAD_ADDR + \
+ CONFIG_SYS_MONITOR_LEN);
+ size_t size = 0;
+ size_t offset = -1;
+ char *autoload = getenv("firmware_autoload");
+ u8 pnum;
+ struct mtd_device *dev;
+ struct part_info *part;
+
+ /* detect compatibility issue of environment version */
+ s = getenv("env_version");
+ if ((NULL == s) || (0 != strcmp(s, CONFIG_ENV_VERSION))) {
+ char * const vars[] = {"flash_reset_env"};
+ printf("*** Warning - Environment version change suggests: "
+ "run flash_reset_env; reset\n");
+ set_default_vars(1, vars);
+ }
+
+ /* Unlock whole flash but U-Boot */
+ s = getenv("env_offset");
+ offset = CONFIG_ENV_OFFSET;
+ if ((s != NULL) && (0 != strcmp(s, "0")))
+ offset = simple_strtoul(s, NULL, 16);
+
+ if (nand_unlock(&nand_info[0], offset, nand_info[0].size - offset, 0))
+ printf("NAND flash lock/unlocked failed\n");
+
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ printf("Board: Armadeus APF27 revision %d\n", get_board_rev());
+ return 0;
+}
+
+void enable_caches(void)
+{
+ /* Enable D-cache. I-cache is already enabled in start.S */
+ dcache_enable();
+}
+
+inline void lowlevel_init(void) {}
diff --git a/board/armadeus/apf27/apf27.h b/board/armadeus/apf27/apf27.h
new file mode 100644
index 0000000..bb007e8
--- /dev/null
+++ b/board/armadeus/apf27/apf27.h
@@ -0,0 +1,477 @@
+#ifndef __APF27_H
+#define __APF27_H
+
+/* FPGA program pin configuration */
+#define ACFG_FPGA_PWR (GPIO_PORTF | 19) /* FPGA prog pin */
+#define ACFG_FPGA_PRG (GPIO_PORTF | 11) /* FPGA prog pin */
+#define ACFG_FPGA_CLK (GPIO_PORTF | 15) /* FPGA clk pin */
+#define ACFG_FPGA_RDATA 0xD6000000 /* FPGA data addr */
+#define ACFG_FPGA_WDATA 0xD6000000 /* FPGA data addr */
+#define ACFG_FPGA_INIT (GPIO_PORTF | 12) /* FPGA init pin */
+#define ACFG_FPGA_DONE (GPIO_PORTF | 9) /* FPGA done pin */
+#define ACFG_FPGA_RW (GPIO_PORTF | 21) /* FPGA done pin */
+#define ACFG_FPGA_CS (GPIO_PORTF | 22) /* FPGA done pin */
+#define ACFG_FPGA_SUSPEND (GPIO_PORTF | 10) /* FPGA done pin */
+#define ACFG_FPGA_RESET (GPIO_PORTF | 7) /* FPGA done pin */
+
+/* MPU CLOCK source before PLL */
+/* ACFG_CLK_FREQ (2/3 MPLL clock or ext 266 MHZ) */
+#ifndef CONFIG_MX27_CLK26
+#if (CONFIG_MX27_CLK32 == 32000)
+#define ACFG_MPCTL0_VAL 0x00211803 /* 398.998 MHz */
+#define ACFG_MPCTL1_VAL 0
+#define CONFIG_MPLL_FREQ 399
+#else /* CONFIG_MX27_CLK32 == 32768*/
+#define ACFG_MPCTL0_VAL 0x01EF15D5 /* 399.000 MHz */
+#define ACFG_MPCTL1_VAL 0
+#define CONFIG_MPLL_FREQ 399
+#endif /* CONFIG_MX27_CLK32 */
+#else /* CONFIG_MX27_CLK26 in use*/
+#define ACFG_MPCTL0_VAL 0x00331C23 /* 399.000 MHz */
+#define ACFG_MPCTL1_VAL 0
+#define CONFIG_MPLL_FREQ 399
+#endif /* CONFIG_MX27_CLK26 */
+
+#define ACFG_CLK_FREQ (CONFIG_MPLL_FREQ*2/3) /* 266 MHz */
+
+/* Serial clock source before PLL (should be named ACFG_SYSPLL_CLK_FREQ)*/
+#ifndef CONFIG_MX27_CLK26
+#if (CONFIG_MX27_CLK32 == 32000)
+#define ACFG_SPCTL0_VAL 0x04A02419 /* 300.00020 MHz */
+#define ACFG_SPCTL1_VAL 0
+#define CONFIG_SPLL_FREQ 300 /* MHz */
+#else /* CONFIG_MX27_CLK32 == 32768*/
+#define ACFG_SPCTL0_VAL 0x0475206F /* 299.99937 MHz */
+#define ACFG_SPCTL1_VAL 0
+#define CONFIG_SPLL_FREQ 300 /* MHz */
+#endif /* CONFIG_MX27_CLK32 */
+#else /* CONFIG_MX27_CLK26 in use*/
+#define ACFG_SPCTL0_VAL 0x040C2C07 /* 300 MHz */
+#define ACFG_SPCTL1_VAL 0x0
+#define CONFIG_SPLL_FREQ 300 /* MHz */
+#endif /* CONFIG_MX27_CLK26 */
+
+/* ARM bus frequency (have to be a CONFIG_MPLL_FREQ ratio) */
+#define CONFIG_ARM_FREQ 399 /* up to 400 MHz */
+
+/* external bus frequency (have to be a ACFG_CLK_FREQ ratio) */
+#define CONFIG_HCLK_FREQ 133 /* (ACFG_CLK_FREQ/2) */
+
+#define CONFIG_PERIF1_FREQ 16 /* 16.625 MHz UART, GPT, PWM*/
+#define CONFIG_PERIF2_FREQ 33 /* 33.25 MHz CSPI and SDHC */
+#define CONFIG_PERIF3_FREQ 33 /* 33.25 MHz LCD*/
+#define CONFIG_PERIF4_FREQ 33 /* 33.25 MHz CSI*/
+#define CONFIG_SSI1_FREQ 66 /* 66.50 MHz SSI1*/
+#define CONFIG_SSI2_FREQ 66 /* 66.50 MHz SSI2*/
+#define CONFIG_MSHC_FREQ 66 /* 66.50 MHz MSHC*/
+#define CONFIG_H264_FREQ 66 /* 66.50 MHz H264*/
+#define CONFIG_CLK0_DIV 3 /* Divide CLK0 by 4 */
+#define CONFIG_CLK0_EN 1 /* CLK0 enabled */
+
+/* external bus frequency (have to be a CONFIG_HCLK_FREQ ratio) */
+#define CONFIG_NFC_FREQ 44 /* NFC Clock up to 44 MHz wh 133MHz*/
+
+/* external serial bus frequency (have to be a CONFIG_SPLL_FREQ ratio) */
+#define CONFIG_USB_FREQ 60 /* 60 MHz */
+
+/*
+ * SDRAM
+ */
+#if (ACFG_SDRAM_MBYTE_SYZE == 64) /* micron MT46H16M32LF -6 */
+/* micron 64MB */
+#define ACFG_SDRAM_NUM_COL 9 /* 8, 9, 10 or 11
+ column address bits */
+#define ACFG_SDRAM_NUM_ROW 13 /* 11, 12 or 13
+ row address bits */
+#define ACFG_SDRAM_REFRESH 3 /* 0=OFF 1=2048
+ 2=4096 3=8192 refresh */
+#define ACFG_SDRAM_EXIT_PWD 25 /* ns exit power
+ down delay */
+#define ACFG_SDRAM_W2R_DELAY 1 /* write to read
+ cycle delay > 0 */
+#define ACFG_SDRAM_ROW_PRECHARGE_DELAY 18 /* ns */
+#define ACFG_SDRAM_TMRD_DELAY 2 /* Load mode register
+ cycle delay 1..4 */
+#define ACFG_SDRAM_TWR_DELAY 1 /* LPDDR: 0=2ck 1=3ck;
+ SDRAM: 0=1ck 1=2ck*/
+#define ACFG_SDRAM_RAS_DELAY 42 /* ns ACTIVE-to-PRECHARGE
+ delay */
+#define ACFG_SDRAM_RRD_DELAY 12 /* ns ACTIVE-to-ACTIVE
+ delay */
+#define ACFG_SDRAM_RCD_DELAY 18 /* ns Row to Column delay */
+#define ACFG_SDRAM_RC_DELAY 70 /* ns Row cycle delay (tRFC
+ refresh to command) */
+#define ACFG_SDRAM_CLOCK_CYCLE_CL_1 0 /* ns clock cycle time
+ estimated fo CL=1
+ 0=force 3 for lpddr */
+#define ACFG_SDRAM_PARTIAL_ARRAY_SR 0 /* 0=full 1=half 2=quater
+ 3=Eighth 4=Sixteenth */
+#define ACFG_SDRAM_DRIVE_STRENGH 0 /* 0=Full-strength 1=half
+ 2=quater 3=Eighth */
+#define ACFG_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
+#define ACFG_SDRAM_SINGLE_ACCESS 0 /* 1= single access;
+ 0 = Burst mode */
+#endif
+
+#if (ACFG_SDRAM_MBYTE_SYZE == 128)
+/* micron 128MB */
+#define ACFG_SDRAM_NUM_COL 9 /* 8, 9, 10 or 11
+ column address bits */
+#define ACFG_SDRAM_NUM_ROW 14 /* 11, 12 or 13
+ row address bits */
+#define ACFG_SDRAM_REFRESH 3 /* 0=OFF 1=2048
+ 2=4096 3=8192 refresh */
+#define ACFG_SDRAM_EXIT_PWD 25 /* ns exit power
+ down delay */
+#define ACFG_SDRAM_W2R_DELAY 1 /* write to read
+ cycle delay > 0 */
+#define ACFG_SDRAM_ROW_PRECHARGE_DELAY 18 /* ns */
+#define ACFG_SDRAM_TMRD_DELAY 2 /* Load mode register
+ cycle delay 1..4 */
+#define ACFG_SDRAM_TWR_DELAY 1 /* LPDDR: 0=2ck 1=3ck;
+ SDRAM: 0=1ck 1=2ck*/
+#define ACFG_SDRAM_RAS_DELAY 42 /* ns ACTIVE-to-PRECHARGE
+ delay */
+#define ACFG_SDRAM_RRD_DELAY 12 /* ns ACTIVE-to-ACTIVE
+ delay */
+#define ACFG_SDRAM_RCD_DELAY 18 /* ns Row to Column delay */
+#define ACFG_SDRAM_RC_DELAY 70 /* ns Row cycle delay (tRFC
+ refresh to command)*/
+#define ACFG_SDRAM_CLOCK_CYCLE_CL_1 0 /* ns clock cycle time
+ estimated fo CL=1
+ 0=force 3 for lpddr*/
+#define ACFG_SDRAM_PARTIAL_ARRAY_SR 0 /* 0=full 1=half 2=quater
+ 3=Eighth 4=Sixteenth */
+#define ACFG_SDRAM_DRIVE_STRENGH 0 /* 0=Full-strength 1=half
+ 2=quater 3=Eighth */
+#define ACFG_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
+#define ACFG_SDRAM_SINGLE_ACCESS 0 /* 1= single access;
+ 0 = Burst mode */
+#endif
+
+#if (ACFG_SDRAM_MBYTE_SYZE == 256)
+/* micron 256MB */
+#define ACFG_SDRAM_NUM_COL 10 /* 8, 9, 10 or 11
+ column address bits */
+#define ACFG_SDRAM_NUM_ROW 14 /* 11, 12 or 13
+ row address bits */
+#define ACFG_SDRAM_REFRESH 3 /* 0=OFF 1=2048
+ 2=4096 3=8192 refresh */
+#define ACFG_SDRAM_EXIT_PWD 25 /* ns exit power
+ down delay */
+#define ACFG_SDRAM_W2R_DELAY 1 /* write to read cycle
+ delay > 0 */
+#define ACFG_SDRAM_ROW_PRECHARGE_DELAY 18 /* ns */
+#define ACFG_SDRAM_TMRD_DELAY 2 /* Load mode register
+ cycle delay 1..4 */
+#define ACFG_SDRAM_TWR_DELAY 1 /* LPDDR: 0=2ck 1=3ck;
+ SDRAM: 0=1ck 1=2ck */
+#define ACFG_SDRAM_RAS_DELAY 42 /* ns ACTIVE-to-PRECHARGE
+ delay */
+#define ACFG_SDRAM_RRD_DELAY 12 /* ns ACTIVE-to-ACTIVE
+ delay */
+#define ACFG_SDRAM_RCD_DELAY 18 /* ns Row to Column delay */
+#define ACFG_SDRAM_RC_DELAY 70 /* ns Row cycle delay (tRFC
+ refresh to command) */
+#define ACFG_SDRAM_CLOCK_CYCLE_CL_1 0 /* ns clock cycle time
+ estimated fo CL=1
+ 0=force 3 for lpddr */
+#define ACFG_SDRAM_PARTIAL_ARRAY_SR 0 /* 0=full 1=half 2=quater
+ 3=Eighth 4=Sixteenth */
+#define ACFG_SDRAM_DRIVE_STRENGH 0 /* 0=Full-strength
+ 1=half
+ 2=quater
+ 3=Eighth */
+#define ACFG_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
+#define ACFG_SDRAM_SINGLE_ACCESS 0 /* 1= single access;
+ 0 = Burst mode */
+#endif
+
+/*
+ * External interface
+ */
+/*
+ * CSCRxU_VAL:
+ * 31| x | x | x x |x x x x| x x | x | x |x x x x|16
+ * |SP |WP | BCD | BCS | PSZ |PME|SYNC| DOL |
+ *
+ * 15| x x | x x x x x x | x | x x x x | x x x x |0
+ * | CNC | WSC |EW | WWS | EDC |
+ *
+ * CSCRxL_VAL:
+ * 31| x x x x | x x x x | x x x x | x x x x |16
+ * | OEA | OEN | EBWA | EBWN |
+ * 15|x x x x| x |x x x |x x x x| x | x | x | x | 0
+ * | CSA |EBC| DSZ | CSN |PSR|CRE|WRAP|CSEN|
+ *
+ * CSCRxA_VAL:
+ * 31| x x x x | x x x x | x x x x | x x x x |16
+ * | EBRA | EBRN | RWA | RWN |
+ * 15| x | x x |x x x|x x|x x|x x| x | x | x | x | 0
+ * |MUM| LAH | LBN |LBA|DWW|DCT|WWU|AGE|CNC2|FCE|
+ */
+
+/* CS0 configuration for 16 bit nor flash */
+#define ACFG_CS0U_VAL 0x0000CC03
+#define ACFG_CS0L_VAL 0xa0330D01
+#define ACFG_CS0A_VAL 0x00220800
+
+#define ACFG_CS1U_VAL 0x00000f00
+#define ACFG_CS1L_VAL 0x00000D01
+#define ACFG_CS1A_VAL 0
+
+#define ACFG_CS2U_VAL 0
+#define ACFG_CS2L_VAL 0
+#define ACFG_CS2A_VAL 0
+
+#define ACFG_CS3U_VAL 0
+#define ACFG_CS3L_VAL 0
+#define ACFG_CS3A_VAL 0
+
+#define ACFG_CS4U_VAL 0
+#define ACFG_CS4L_VAL 0
+#define ACFG_CS4A_VAL 0
+
+/* FPGA 16 bit data bus */
+#define ACFG_CS5U_VAL 0x00000600
+#define ACFG_CS5L_VAL 0x00000D01
+#define ACFG_CS5A_VAL 0
+
+#define ACFG_EIM_VAL 0x00002200
+
+/* FPGA specific settings */
+/* CLKO */
+#define ACFG_CCSR_VAL 0x00000305
+/* drive strength CLKO set to 2*/
+#define ACFG_DSCR10_VAL 0x00020000
+/* drive strength A1..A12 set to 2*/
+#define ACFG_DSCR3_VAL 0x02AAAAA8
+/* drive strength ctrl*/
+#define ACFG_DSCR7_VAL 0x00020880
+/* drive strength data*/
+#define ACFG_DSCR2_VAL 0xAAAAAAAA
+
+
+/*
+ * Default configuration for GPIOs and peripherals
+ */
+#ifndef ACFG_APF27_CUSTOM
+#define ACFG_DDIR_A_VAL 0x00000000
+#define ACFG_OCR1_A_VAL 0x00000000
+#define ACFG_OCR2_A_VAL 0x00000000
+#define ACFG_ICFA1_A_VAL 0xFFFFFFFF
+#define ACFG_ICFA2_A_VAL 0xFFFFFFFF
+#define ACFG_ICFB1_A_VAL 0xFFFFFFFF
+#define ACFG_ICFB2_A_VAL 0xFFFFFFFF
+#define ACFG_DR_A_VAL 0x00000000
+#define ACFG_GIUS_A_VAL 0xFFFFFFFF
+#define ACFG_ICR1_A_VAL 0x00000000
+#define ACFG_ICR2_A_VAL 0x00000000
+#define ACFG_IMR_A_VAL 0x00000000
+#define ACFG_GPR_A_VAL 0x00000000
+#define ACFG_PUEN_A_VAL 0xFFFFFFFF
+
+#define ACFG_DDIR_B_VAL 0x00000000
+#define ACFG_OCR1_B_VAL 0x00000000
+#define ACFG_OCR2_B_VAL 0x00000000
+#define ACFG_ICFA1_B_VAL 0xFFFFFFFF
+#define ACFG_ICFA2_B_VAL 0xFFFFFFFF
+#define ACFG_ICFB1_B_VAL 0xFFFFFFFF
+#define ACFG_ICFB2_B_VAL 0xFFFFFFFF
+#define ACFG_DR_B_VAL 0x00000000
+#define ACFG_GIUS_B_VAL 0xFF3FFFF0
+#define ACFG_ICR1_B_VAL 0x00000000
+#define ACFG_ICR2_B_VAL 0x00000000
+#define ACFG_IMR_B_VAL 0x00000000
+#define ACFG_GPR_B_VAL 0x00000000
+#define ACFG_PUEN_B_VAL 0xFFFFFFFF
+
+#define ACFG_DDIR_C_VAL 0x00000000
+#define ACFG_OCR1_C_VAL 0x00000000
+#define ACFG_OCR2_C_VAL 0x00000000
+#define ACFG_ICFA1_C_VAL 0xFFFFFFFF
+#define ACFG_ICFA2_C_VAL 0xFFFFFFFF
+#define ACFG_ICFB1_C_VAL 0xFFFFFFFF
+#define ACFG_ICFB2_C_VAL 0xFFFFFFFF
+#define ACFG_DR_C_VAL 0x00000000
+#define ACFG_GIUS_C_VAL 0xFFFFC07F
+#define ACFG_ICR1_C_VAL 0x00000000
+#define ACFG_ICR2_C_VAL 0x00000000
+#define ACFG_IMR_C_VAL 0x00000000
+#define ACFG_GPR_C_VAL 0x00000000
+#define ACFG_PUEN_C_VAL 0xFFFFFF87
+
+#define ACFG_DDIR_D_VAL 0x00000000
+#define ACFG_OCR1_D_VAL 0x00000000
+#define ACFG_OCR2_D_VAL 0x00000000
+#define ACFG_ICFA1_D_VAL 0xFFFFFFFF
+#define ACFG_ICFA2_D_VAL 0xFFFFFFFF
+#define ACFG_ICFB1_D_VAL 0xFFFFFFFF
+#define ACFG_ICFB2_D_VAL 0xFFFFFFFF
+#define ACFG_DR_D_VAL 0x00000000
+#define ACFG_GIUS_D_VAL 0xFFFFFFFF
+#define ACFG_ICR1_D_VAL 0x00000000
+#define ACFG_ICR2_D_VAL 0x00000000
+#define ACFG_IMR_D_VAL 0x00000000
+#define ACFG_GPR_D_VAL 0x00000000
+#define ACFG_PUEN_D_VAL 0xFFFFFFFF
+
+#define ACFG_DDIR_E_VAL 0x00000000
+#define ACFG_OCR1_E_VAL 0x00000000
+#define ACFG_OCR2_E_VAL 0x00000000
+#define ACFG_ICFA1_E_VAL 0xFFFFFFFF
+#define ACFG_ICFA2_E_VAL 0xFFFFFFFF
+#define ACFG_ICFB1_E_VAL 0xFFFFFFFF
+#define ACFG_ICFB2_E_VAL 0xFFFFFFFF
+#define ACFG_DR_E_VAL 0x00000000
+#define ACFG_GIUS_E_VAL 0xFCFFCCF8
+#define ACFG_ICR1_E_VAL 0x00000000
+#define ACFG_ICR2_E_VAL 0x00000000
+#define ACFG_IMR_E_VAL 0x00000000
+#define ACFG_GPR_E_VAL 0x00000000
+#define ACFG_PUEN_E_VAL 0xFFFFFFFF
+
+#define ACFG_DDIR_F_VAL 0x00000000
+#define ACFG_OCR1_F_VAL 0x00000000
+#define ACFG_OCR2_F_VAL 0x00000000
+#define ACFG_ICFA1_F_VAL 0xFFFFFFFF
+#define ACFG_ICFA2_F_VAL 0xFFFFFFFF
+#define ACFG_ICFB1_F_VAL 0xFFFFFFFF
+#define ACFG_ICFB2_F_VAL 0xFFFFFFFF
+#define ACFG_DR_F_VAL 0x00000000
+#define ACFG_GIUS_F_VAL 0xFF7F8000
+#define ACFG_ICR1_F_VAL 0x00000000
+#define ACFG_ICR2_F_VAL 0x00000000
+#define ACFG_IMR_F_VAL 0x00000000
+#define ACFG_GPR_F_VAL 0x00000000
+#define ACFG_PUEN_F_VAL 0xFFFFFFFF
+#endif /* ACFG_APF27_CUSTOM */
+
+/* Enforce DDR signal strengh & enable USB/PP/DMA burst override bits */
+#define ACFG_GPCR_VAL 0x0003000F
+
+#define ACFG_ESDMISC_VAL ESDMISC_LHD+ESDMISC_MDDREN
+
+/* FMCR select num LPDDR RAMs and nand 16bits, 2KB pages */
+#if (CONFIG_NR_DRAM_BANKS == 1)
+#define ACFG_FMCR_VAL 0xFFFFFFF9
+#elif (CONFIG_NR_DRAM_BANKS == 2)
+#define ACFG_FMCR_VAL 0xFFFFFFFB
+#endif
+
+#ifndef ACFG_APF27_CUSTOM
+#define ACFG_AIPI1_PSR0_VAL 0x20040304
+#define ACFG_AIPI1_PSR1_VAL 0xDFFBFCFB
+#define ACFG_AIPI2_PSR0_VAL 0x00000000
+#define ACFG_AIPI2_PSR1_VAL 0xFFFFFFFF
+#endif /* ACFG_APF27_CUSTOM */
+
+/* PCCR enable DMA FEC I2C1 IIM SDHC1 */
+#ifndef ACFG_APF27_CUSTOM
+#define ACFG_PCCR0_VAL 0x05070410
+#define ACFG_PCCR1_VAL 0xA14A0608
+#endif /* ACFG_APF27_CUSTOM */
+
+/*
+ * From here, there should not be any user configuration.
+ * All Equations are automatic
+ */
+
+/* fixme none integer value (7.5ns) => 2*hclock = 15ns */
+#define ACFG_2XHCLK_LGTH (2000/CONFIG_HCLK_FREQ) /* ns */
+
+/* USB 60 MHz ; ARM up to 400; HClK up to 133MHz*/
+#ifdef CONFIG_MX27_CLK26
+#define CSCR_MASK 0x0303800D
+#else
+#define CSCR_MASK 0x0300800D
+#endif
+#define ACFG_CSCR_VAL\
+ (CSCR_MASK \
+ |((((CONFIG_SPLL_FREQ/CONFIG_USB_FREQ)-1)&0x07) << 28) \
+ |((((CONFIG_MPLL_FREQ/CONFIG_ARM_FREQ)-1)&0x03) << 12) \
+ |((((ACFG_CLK_FREQ/CONFIG_HCLK_FREQ)-1)&0x03) << 8))
+
+/* SSIx CLKO NFC H264 MSHC */
+#define ACFG_PCDR0_VAL\
+ (((((ACFG_CLK_FREQ/CONFIG_MSHC_FREQ)-1)&0x3F)<<0) \
+ |((((CONFIG_HCLK_FREQ/CONFIG_NFC_FREQ)-1)&0x0F)<<6) \
+ |(((((ACFG_CLK_FREQ/CONFIG_H264_FREQ)-2)*2)&0x3F)<<10)\
+ |(((((ACFG_CLK_FREQ/CONFIG_SSI1_FREQ)-2)*2)&0x3F)<<16)\
+ |(((CONFIG_CLK0_DIV)&0x07)<<22)\
+ |(((CONFIG_CLK0_EN)&0x01)<<25)\
+ |(((((ACFG_CLK_FREQ/CONFIG_SSI2_FREQ)-2)*2)&0x3F)<<26))
+
+/* PERCLKx */
+#define ACFG_PCDR1_VAL\
+ (((((ACFG_CLK_FREQ/CONFIG_PERIF1_FREQ)-1)&0x3F)<<0) \
+ |((((ACFG_CLK_FREQ/CONFIG_PERIF2_FREQ)-1)&0x3F)<<8) \
+ |((((ACFG_CLK_FREQ/CONFIG_PERIF3_FREQ)-1)&0x3F)<<16) \
+ |((((ACFG_CLK_FREQ/CONFIG_PERIF4_FREQ)-1)&0x3F)<<24))
+
+/* SDRAM controller programming Values */
+#if (((2*ACFG_SDRAM_CLOCK_CYCLE_CL_1) > (3*ACFG_2XHCLK_LGTH)) \
+ || (ACFG_SDRAM_CLOCK_CYCLE_CL_1 < 1))
+#define REG_FIELD_SCL_VAL 3
+#define REG_FIELD_SCLIMX_VAL 0
+#else
+#define REG_FIELD_SCL_VAL\
+ ((2*ACFG_SDRAM_CLOCK_CYCLE_CL_1+ACFG_2XHCLK_LGTH-1)/ \
+ ACFG_2XHCLK_LGTH)
+#define REG_FIELD_SCLIMX_VAL REG_FIELD_SCL_VAL
+#endif
+
+#if ((2*ACFG_SDRAM_RC_DELAY) > (16*ACFG_2XHCLK_LGTH))
+#define REG_FIELD_SRC_VAL 0
+#else
+#define REG_FIELD_SRC_VAL\
+ ((2*ACFG_SDRAM_RC_DELAY+ACFG_2XHCLK_LGTH-1)/ \
+ ACFG_2XHCLK_LGTH)
+#endif
+
+/* TBD Power down timer ; PRCT Bit Field Encoding; burst length 8 ; FP = 0*/
+#define REG_ESDCTL_BASE_CONFIG (0x80020485\
+ | (((ACFG_SDRAM_NUM_ROW-11)&0x7)<<24)\
+ | (((ACFG_SDRAM_NUM_COL-8)&0x3)<<20)\
+ | (((ACFG_SDRAM_REFRESH)&0x7)<<13))
+
+#define ACFG_NORMAL_RW_CMD ((0x0<<28)+REG_ESDCTL_BASE_CONFIG)
+#define ACFG_PRECHARGE_CMD ((0x1<<28)+REG_ESDCTL_BASE_CONFIG)
+#define ACFG_AUTOREFRESH_CMD ((0x2<<28)+REG_ESDCTL_BASE_CONFIG)
+#define ACFG_SET_MODE_REG_CMD ((0x3<<28)+REG_ESDCTL_BASE_CONFIG)
+
+/* ESDRAMC Configuration Registers : force CL=3 to lpddr */
+#define ACFG_SDRAM_ESDCFG_REGISTER_VAL (0x0\
+ | (((((2*ACFG_SDRAM_EXIT_PWD+ACFG_2XHCLK_LGTH-1)/ \
+ ACFG_2XHCLK_LGTH)-1)&0x3)<<21)\
+ | (((ACFG_SDRAM_W2R_DELAY-1)&0x1)<<20)\
+ | (((((2*ACFG_SDRAM_ROW_PRECHARGE_DELAY+ \
+ ACFG_2XHCLK_LGTH-1)/ACFG_2XHCLK_LGTH)-1)&0x3)<<18) \
+ | (((ACFG_SDRAM_TMRD_DELAY-1)&0x3)<<16)\
+ | (((ACFG_SDRAM_TWR_DELAY)&0x1)<<15)\
+ | (((((2*ACFG_SDRAM_RAS_DELAY+ACFG_2XHCLK_LGTH-1)/ \
+ ACFG_2XHCLK_LGTH)-1)&0x7)<<12) \
+ | (((((2*ACFG_SDRAM_RRD_DELAY+ACFG_2XHCLK_LGTH-1)/ \
+ ACFG_2XHCLK_LGTH)-1)&0x3)<<10) \
+ | (((REG_FIELD_SCLIMX_VAL)&0x3)<<8)\
+ | (((((2*ACFG_SDRAM_RCD_DELAY+ACFG_2XHCLK_LGTH-1)/ \
+ ACFG_2XHCLK_LGTH)-1)&0x7)<<4) \
+ | (((REG_FIELD_SRC_VAL)&0x0F)<<0))
+
+/* Issue Mode register Command to SDRAM*/
+#define ACFG_SDRAM_MODE_REGISTER_VAL\
+ ((((ACFG_SDRAM_BURST_LENGTH)&0x7)<<(0))\
+ | (((REG_FIELD_SCL_VAL)&0x7)<<(4))\
+ | ((0)<<(3)) /* sequentiql access */ \
+ /*| (((ACFG_SDRAM_SINGLE_ACCESS)&0x1)<<(1))*/)
+
+/* Issue Extended Mode register Command to SDRAM*/
+#define ACFG_SDRAM_EXT_MODE_REGISTER_VAL\
+ ((ACFG_SDRAM_PARTIAL_ARRAY_SR<<0)\
+ | (ACFG_SDRAM_DRIVE_STRENGH<<(5))\
+ | (1<<(ACFG_SDRAM_NUM_COL+ACFG_SDRAM_NUM_ROW+1+2)))
+
+/* Issue Precharge all Command to SDRAM*/
+#define ACFG_SDRAM_PRECHARGE_ALL_VAL (1<<10)
+
+#endif /* __APF27_H */
diff --git a/boards.cfg b/boards.cfg
index 4c63789..72c49df 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -184,6 +184,7 @@ jadecpu arm arm926ejs jadecpu syteco
mx25pdk arm arm926ejs mx25pdk freescale mx25 mx25pdk:IMX_CONFIG=board/freescale/mx25pdk/imximage.cfg
tx25 arm arm926ejs tx25 karo mx25
zmx25 arm arm926ejs zmx25 syteco mx25
+apf27 arm arm926ejs apf27 armadeus mx27
imx27lite arm arm926ejs imx27lite logicpd mx27
magnesium arm arm926ejs imx27lite logicpd mx27
apx4devkit arm arm926ejs apx4devkit bluegiga mxs apx4devkit
diff --git a/include/configs/apf27.h b/include/configs/apf27.h
new file mode 100644
index 0000000..005f10e
--- /dev/null
+++ b/include/configs/apf27.h
@@ -0,0 +1,458 @@
+/*
+ *
+ * Configuration settings for the Armadeus Project motherboard APF27
+ *
+ * Copyright (C) 2008-2012 ej / Armadeus Project <eric.jarrige@armadeus.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_ENV_VERSION "3.3"
+#define CONFIG_IDENT_STRING " apf27 patch 3.8"
+#define CONFIG_BOARD_NAME apf27
+
+/*
+ * SoC configurations
+ */
+#define CONFIG_ARM926EJS /* this is an ARM926EJS CPU */
+#define CONFIG_MX27 /* in a Freescale i.MX27 Chip */
+#define CONFIG_MACH_TYPE 1698 /* APF27 */
+
+/*
+ * Enable the call to miscellaneous platform dependent initialization.
+ */
+#define CONFIG_SYS_NO_FLASH /* to be define before <config_cmd_default.h> */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/*
+ * Board display option
+ */
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_DISPLAY_CPUINFO
+
+/*
+ * SPL
+ */
+/* Copy SPL+U-Boot here */
+#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_TEXT_BASE - 0x800)
+/* Size is the partion size */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE CONFIG_SYS_MONITOR_LEN
+/* Build image with spl and u-boot */
+#define CONFIG_NAND_U_BOOT
+#define CONFIG_SPL_PAD_TO 0xa1000000
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
+#define CONFIG_SPL_START_S_PATH "board/armadeus/apf27"
+#define CONFIG_SPL_LDSCRIPT "board/armadeus/apf27/u-boot-spl.lds"
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+
+#define CONFIG_HOSTNAME CONFIG_BOARD_NAME
+#define CONFIG_ROOTPATH "/tftpboot/" __stringify(CONFIG_BOARD_NAME) "-root"
+
+/*
+ * U-Boot Commands
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV /* ask for env variable */
+#define CONFIG_CMD_BSP /* Board Specific functions */
+#define CONFIG_CMD_CACHE /* icache, dcache */
+#define CONFIG_CMD_DHCP /* DHCP Support */
+#define CONFIG_CMD_DNS
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT /* FAT support */
+#define CONFIG_CMD_IMX_FUSE /* imx iim fuse */
+#define CONFIG_CMD_MII /* MII support */
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_MTDPARTS /* MTD partition support */
+#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_NAND_LOCK_UNLOCK
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_CMD_NFS /* NFS support */
+#define CONFIG_CMD_PING /* ping support */
+#define CONFIG_CMD_SETEXPR /* setexpr support */
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+
+/*
+ * Memory configurations
+ */
+#define CONFIG_NR_DRAM_POPULATED 2
+#define CONFIG_NR_DRAM_BANKS 2
+
+#define ACFG_SDRAM_MBYTE_SYZE 64
+
+#define PHYS_SDRAM_1 0xA0000000
+#define PHYS_SDRAM_2 0xB0000000
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (512<<10))
+#define CONFIG_SYS_MEMTEST_START 0xA0000000 /* memtest test area */
+#define CONFIG_SYS_MEMTEST_END 0xA0300000 /* 3 MiB RAM test */
+
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE \
+ + PHYS_SDRAM_1_SIZE - 0x0100000)
+
+#define CONFIG_SYS_TEXT_BASE 0xA1000000
+
+/*
+ * FLASH organization
+ */
+#define ACFG_MONITOR_OFFSET 0x00000000
+#define CONFIG_SYS_MONITOR_LEN 0x00100000 /* 1MiB */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_ENV_OFFSET 0x00100000 /* NAND offset */
+#define CONFIG_ENV_SIZE 0x00020000 /* 128kB */
+#define CONFIG_ENV_RANGE 0X00080000 /* 512kB */
+#define CONFIG_ENV_OFFSET_REDUND \
+ (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) /* +512kB */
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE /* 512kB */
+#define CONFIG_FIRMWARE_OFFSET 0x00200000
+#define CONFIG_KERNEL_OFFSET 0x00300000
+#define CONFIG_ROOTFS_OFFSET 0x00800000
+
+#define CONFIG_MTDMAP "mxc_nand.0"
+#define MTDIDS_DEFAULT "nand0=" CONFIG_MTDMAP
+#define MTDPARTS_DEFAULT "mtdparts=" CONFIG_MTDMAP \
+ ":1M(u-boot)ro," \
+ "512K(env)," \
+ "512K(env2)," \
+ "512K(firmware)," \
+ "512K(dtb)," \
+ "5M(kernel)," \
+ "-(rootfs)"
+
+/*
+ * U-Boot general configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "BIOS> " /* prompt string */
+#define CONFIG_SYS_CBSIZE 2048 /* console I/O buffer */
+#define CONFIG_SYS_PBSIZE \
+ (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+ /* Print buffer size */
+#define CONFIG_SYS_MAXARGS 16 /* max command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+ /* Boot argument buffer size */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_HUSH_PARSER /* enable the "hush" shell */
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* secondary prompt string */
+
+/*
+ * Boot Linux
+ */
+#define CONFIG_CMDLINE_TAG /* send commandline to Kernel */
+#define CONFIG_SETUP_MEMORY_TAGS /* send memory definition to kernel */
+#define CONFIG_INITRD_TAG /* send initrd params */
+
+#define CONFIG_OF_LIBFDT
+
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_BOOTFILE __stringify(CONFIG_BOARD_NAME) "-linux.bin"
+#define CONFIG_BOOTARGS "console=" __stringify(ACFG_CONSOLE_DEV) "," \
+ __stringify(CONFIG_BAUDRATE) " " MTDPARTS_DEFAULT \
+ " ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs "
+
+#define ACFG_CONSOLE_DEV ttySMX0
+#define CONFIG_BOOTCOMMAND "run ubifsboot"
+#define CONFIG_SYS_AUTOLOAD "no"
+/*
+ * Default load address for user programs and kernel
+ */
+#define CONFIG_LOADADDR 0xA0000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+/*
+ * Extra Environments
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "env_version=" CONFIG_ENV_VERSION "\0" \
+ "consoledev=" __stringify(ACFG_CONSOLE_DEV) "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "partition=nand0,6\0" \
+ "u-boot_addr=" __stringify(ACFG_MONITOR_OFFSET) "\0" \
+ "env_addr=" __stringify(CONFIG_ENV_OFFSET) "\0" \
+ "firmware_addr=" __stringify(CONFIG_FIRMWARE_OFFSET) "\0" \
+ "kernel_addr=" __stringify(CONFIG_KERNEL_OFFSET) "\0" \
+ "rootfs_addr=" __stringify(CONFIG_ROOTFS_OFFSET) "\0" \
+ "board_name=" __stringify(CONFIG_BOARD_NAME) "\0" \
+ "kernel_addr_r=A0000000\0" \
+ "addnfsargs=setenv bootargs ${bootargs} " \
+ "root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \
+ "addubifsargs=setenv bootargs ${bootargs} " \
+ "ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs\0" \
+ "addmmcargs=setenv bootargs ${bootargs} " \
+ "root=/dev/mmcblk0p1 rootfstype=ext2\0" \
+ "addipargs=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:" \
+ "${hostname}:eth0:off \0" \
+ "nfsboot=setenv bootargs console=${consoledev},${baudrate} " \
+ "${mtdparts} ${extrabootargs}; run addnfsargs addipargs;"\
+ "nfs ${kernel_addr_r} " \
+ "${serverip}:${rootpath}/boot/${board_name}-linux.bin;" \
+ "if test -n ${fdt_addr_r} ; then " \
+ "nand read ${fdt_addr_r} dtb; fi;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "ubifsboot=setenv bootargs console=${consoledev},${baudrate} " \
+ "${mtdparts} ${extrabootargs};run addubifsargs addipargs;"\
+ "if test -n ${fdt_addr_r} ; then " \
+ "nand read ${fdt_addr_r} dtb; fi;" \
+ "nboot ${kernel_addr_r} kernel;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "mmcboot=setenv bootargs console=${consoledev},${baudrate} " \
+ "${mtdparts} ${extrabootargs}; run addmmcargs addipargs;"\
+ "if test -n ${fdt_addr_r} ; then " \
+ "nand read ${fdt_addr_r} dtb; fi;" \
+ "mmc dev 0; ext2load mmc 0 ${kernel_addr_r}" \
+ " /boot/${board_name}-linux.bin;" \
+ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
+ "boot_nfs_fallback_flash=if ping ${serverip};" \
+ "then echo Boot over NFS; run nfsboot;" \
+ "else echo Boot from the board; run ubifsboot;" \
+ "fi\0" \
+ "firmware_autoload=0\0" \
+ "flash_uboot=nand unlock ${u-boot_addr} ;" \
+ "nand erase.part u-boot;" \
+ "if nand write.trimffs ${fileaddr} ${u-boot_addr} ${filesize};"\
+ "then nand lock; nand unlock ${env_addr};" \
+ "echo Flashing of uboot succeed;" \
+ "else echo Flashing of uboot failed;" \
+ "fi; \0" \
+ "flash_firmware=nand erase.part firmware;" \
+ "if nand write.trimffs ${fileaddr} ${firmware_addr} ${filesize};"\
+ "then echo Flashing of Firmware succeed;" \
+ "else echo Flashing of Firmware failed;" \
+ "fi\0" \
+ "flash_kernel=nand erase.part kernel;" \
+ "if nand write.trimffs ${fileaddr} ${kernel_addr} ${filesize};"\
+ "then echo Flashing of kernel succeed;" \
+ "else echo Flashing of kernel failed;" \
+ "fi\0" \
+ "flash_rootfs=nand erase.part rootfs;" \
+ "if nand write.trimffs ${fileaddr} ${rootfs_addr} ${filesize};"\
+ "then echo Flashing of rootfs succeed;" \
+ "else echo Flashing of rootfs failed;" \
+ "fi\0" \
+ "flash_dtb=nand erase.part dtb;" \
+ "if nand write.trimffs ${fileaddr} dtb ${filesize};" \
+ "then echo Flashing of rootfs succeed;" \
+ "else echo Flashing of rootfs failed;" \
+ "fi\0" \
+ "flash_reset_env=env default -f -a; saveenv;" \
+ "echo Flash environment variables erased!\0" \
+ "download_uboot=tftpboot ${loadaddr} ${board_name}-u-boot-nand.bin\0" \
+ "download_kernel=tftpboot ${loadaddr} ${board_name}-linux.bin\0" \
+ "download_rootfs=tftpboot ${loadaddr} ${board_name}-rootfs.ubi\0" \
+ "download_dtb=tftpboot ${loadaddr} imx27-${board_name}.dtb\0" \
+ "update_uboot=run download_uboot flash_uboot\0" \
+ "update_kernel=run download_kernel flash_kernel\0" \
+ "update_rootfs=run download_rootfs flash_rootfs\0" \
+ "update_dtb=run download_dtb flash_dtb\0" \
+ "update_all=run download_kernel flash_kernel download_rootfs " \
+ "flash_rootfs download_uboot flash_uboot\0" \
+ "unlock_regs=mw 10000008 0; mw 10020008 0\0" \
+
+/*
+ * Serial Driver
+ */
+#define CONFIG_MXC_UART
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/*
+ * GPIO
+ */
+#define CONFIG_MXC_GPIO
+
+/*
+ * NOR
+ */
+
+/*
+ * NAND
+ */
+#define CONFIG_NAND_MXC
+
+#define CONFIG_MXC_NAND_REGS_BASE 0xD8000000
+#define CONFIG_SYS_NAND_BASE CONFIG_MXC_NAND_REGS_BASE
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+
+#define CONFIG_MXC_NAND_HWECC
+#define CONFIG_SYS_NAND_LARGEPAGE
+#define IMX27_NAND_16BITS
+#define NAND_MAX_CHIPS 1
+
+
+#define CONFIG_FLASH_SHOW_PROGRESS 45
+#define CONFIG_SYS_NAND_QUIET 1
+
+#define CONFIG_BOOT_TRACE_REG 0xAFFFFFF8 /* Addr to store traces of SPL boot*/
+
+/*
+ * Partitions & Filsystems
+ */
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
+/*
+ * UBIFS
+ */
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+
+/*
+ * Ethernet (on SOC imx FEC)
+ */
+#define CONFIG_FEC_MXC
+
+#define CONFIG_NET_MULTI
+#define CONFIG_FEC_MXC_PHYADDR 0x1f
+#define CONFIG_MII 1 /* MII PHY management */
+
+/*
+ * FPGA
+ */
+#define CONFIG_FPGA CONFIG_SYS_SPARTAN3
+#define CONFIG_FPGA_COUNT 1
+#define CONFIG_FPGA_XILINX
+#define CONFIG_FPGA_SPARTAN3
+#define CONFIG_SYS_FPGA_WAIT 20000 /* 20 ms */
+#define CONFIG_SYS_FPGA_PROG_FEEDBACK
+#define CONFIG_SYS_FPGA_CHECK_CTRLC
+#define CONFIG_SYS_FPGA_CHECK_ERROR
+
+/*
+ * Fuses - IIM
+ */
+#ifdef CONFIG_CMD_IMX_FUSE
+#define IIM_MAC_BANK 0
+#define IIM_MAC_ROW 5
+#define IIM0_SCC_KEY 11
+#define IIM1_SUID 1
+#endif
+
+/*
+ * I2C
+ */
+
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_HARD_I2C 1
+
+#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_I2C_MULTI_BUS 2
+#define CONFIG_SYS_I2C_NOPROBES { }
+
+#ifdef CONFIG_CMD_EEPROM
+# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24LC02 */
+# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* msec */
+#endif /* CONFIG_CMD_EEPROM */
+#endif /* CONFIG_CMD_I2C */
+
+/*
+ * SPI
+ */
+
+/*
+ * SD/MMC
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MXC_MMC
+#define CONFIG_MXC_MCI_REGS_BASE 0x10014000
+#endif
+
+/*
+ * RTC
+ */
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_RTC_DS1374
+#define CONFIG_SYS_RTC_BUS_NUM 0
+#endif /* CONFIG_CMD_DATE */
+
+/*
+ * Watchdog Config
+ */
+
+/*
+ * USB
+ */
+
+/*
+ * Clocks
+ */
+#define CONFIG_SYS_HZ 1000 /* Ticks per second */
+
+/*
+ * PLL
+ *
+ * 31 | x |x| x x x x |x x x x x x x x x x |x x|x x x x|x x x x x x x x x x| 0
+ * |CPLM|X|----PD---|--------MFD---------|XXX|--MFI--|-----MFN-----------|
+ */
+#define CONFIG_MX27_CLK32 32768 /* 32768 or 32000 Hz crystal */
+#undef CONFIG_MX27_CLK26 /* No external 26MHz external clock */
+
+#if (ACFG_SDRAM_MBYTE_SYZE == 64) /* micron MT46H16M32LF -6 */
+/* micron 64MB */
+#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
+#define PHYS_SDRAM_2_SIZE 0x04000000 /* 64 MB */
+#endif
+
+#if (ACFG_SDRAM_MBYTE_SYZE == 128)
+/* micron 128MB */
+#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
+#define PHYS_SDRAM_2_SIZE 0x08000000 /* 128 MB */
+#endif
+
+#if (ACFG_SDRAM_MBYTE_SYZE == 256)
+/* micron 256MB */
+#define PHYS_SDRAM_1_SIZE 0x10000000 /* 256 MB */
+#define PHYS_SDRAM_2_SIZE 0x10000000 /* 256 MB */
+#endif
+
+#endif /* __CONFIG_H */
--
1.7.4.4
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27
2012-10-29 17:35 [U-Boot] [PATCH 0/4] apf27: add support of armadeus apf27 v2 Philippe Reynes
2012-10-29 17:35 ` [U-Boot] [PATCH 1/4] apf27: add missing constant to mx27 Philippe Reynes
2012-10-29 17:35 ` [U-Boot] [PATCH 2/4] apf27: add support for the armadeus APF27 board Philippe Reynes
@ 2012-10-29 17:35 ` Philippe Reynes
2012-10-30 20:50 ` Fabio Estevam
2012-11-26 18:02 ` Albert ARIBAUD
2012-10-29 17:35 ` [U-Boot] [PATCH 4/4] apf27: add FPGA support for the apf27 board Philippe Reynes
3 siblings, 2 replies; 10+ messages in thread
From: Philippe Reynes @ 2012-10-29 17:35 UTC (permalink / raw)
To: u-boot
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
create mode 100644 board/armadeus/apf27/start.S
create mode 100644 board/armadeus/apf27/u-boot-spl.lds
diff --git a/board/armadeus/apf27/Makefile b/board/armadeus/apf27/Makefile
index 1da9548..f57f405 100644
--- a/board/armadeus/apf27/Makefile
+++ b/board/armadeus/apf27/Makefile
@@ -27,11 +27,14 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).o
+ifndef CONFIG_SPL_BUILD
COBJS := apf27.o
+endif
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
SOBJS := $(addprefix $(obj),$(SOBJS))
+START := $(addprefix $(obj),$(START))
$(LIB): $(obj).depend $(OBJS) $(SOBJS)
$(call cmd_link_o_target, $(OBJS) $(SOBJS))
diff --git a/board/armadeus/apf27/start.S b/board/armadeus/apf27/start.S
new file mode 100644
index 0000000..374b4ea
--- /dev/null
+++ b/board/armadeus/apf27/start.S
@@ -0,0 +1,549 @@
+/*
+ * IMX27 NAND Flash SPL (Secondary Program Loader)
+ *
+ * Copyright (c) 2008 Armadeus Project / eja
+ *
+ * Based on Freescale NAND SPL
+ *
+ * Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
+ * Copyright (c) 2008-2012 Eric Jarrige <eric.jarrige@armadeus.org>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <config.h>
+#include <version.h>
+#include <asm/macro.h>
+#include <asm/arch/mxc_nand.h>
+#include <asm/arch/imx-regs.h>
+#include <generated/asm-offsets.h>
+#include "apf27.h"
+
+/*
+ * Standard NAND flash commands
+ */
+#define NAND_CMD_READ0 0
+#define NAND_CMD_READ1 1
+#define NAND_CMD_PAGEPROG 0x10
+#define NAND_CMD_READOOB 0x50
+#define NAND_CMD_ERASE1 0x60
+#define NAND_CMD_STATUS 0x70
+#define NAND_CMD_STATUS_MULTI 0x71
+#define NAND_CMD_SEQIN 0x80
+#define NAND_CMD_READID 0x90
+#define NAND_CMD_ERASE2 0xd0
+#define NAND_CMD_RESET 0xff
+
+/* Extended commands for large page devices */
+#define NAND_CMD_READSTART 0x30
+#define NAND_CMD_CACHEDPROG 0x15
+
+/* Status bits */
+#define NAND_STATUS_FAIL 0x01
+#define NAND_STATUS_FAIL_N1 0x02
+#define NAND_STATUS_TRUE_READY 0x20
+#define NAND_STATUS_READY 0x40
+#define NAND_STATUS_WP 0x80
+
+ .macro nand_boot
+
+#ifdef CONFIG_BOOT_TRACE_REG
+/*
+ * If CONFIG_BOOT_TRACE_REG is a SDRAM address then be sure to use the following
+ * 2 command after SDRAM init
+ */
+
+/* Backup state of previous boot to CONFIG_BOOT_TRACE_REG+4*/
+#define BACKUP_TRACE() \
+ ldr r4, =CONFIG_BOOT_TRACE_REG; \
+ ldr r3, [r4]; \
+ str r3, [r4, #0x04];
+
+/* Save a state of boot at CONFIG_BOOT_TRACE_REG */
+#define BOOT_TRACE(val) \
+ ldr r4, =CONFIG_BOOT_TRACE_REG; \
+ ldr r3, =val; \
+ str r3, [r4];
+#else
+#define BACKUP_TRACE()
+#define BOOT_TRACE(val)
+#endif
+
+nand_boot_setup:
+
+ /* Copy SPL image from flash to SDRAM first */
+ BOOT_TRACE(1)
+ ldr r0, =IMX_NFC_MAIN_AREA0
+ add r2, r0, #(IMX_NFC_SPARE_AREA0-IMX_NFC_MAIN_AREA0) //2KB NFC Buff
+ ldr r1, =CONFIG_SYS_NAND_U_BOOT_DST
+
+ BOOT_TRACE(2)
+1: ldmia r0!, {r3-r10}
+ stmia r1!, {r3-r10}
+ cmp r0, r2
+ blo 1b
+
+
+
+ /* Jump to SDRAM */
+ BOOT_TRACE(3)
+ ldr r1, =0x7FF
+ and r0, pc, r1 /* offset of pc */
+ ldr r1, =CONFIG_SYS_NAND_U_BOOT_DST
+ add r1, r1, #0x10
+ add pc, r0, r1
+ nop
+ nop
+ nop
+ nop
+
+NAND_Copy_Main:
+ BOOT_TRACE(4)
+ /* r0: nfc base. Reloaded after each page copying */
+ ldr r0, =IMX_NFC_MAIN_AREA0
+
+ /* r1: starting flash addr to be copied. Updated constantly */
+ /* bypass the first preloaded pages */
+ ldr r1, =(IMX_NFC_SPARE_AREA0-IMX_NFC_MAIN_AREA0)
+
+ /* r2: end of 1st RAM buf. Doesn't change */
+ ldr r2, =IMX_NFC_MAIN_AREA1
+
+ /* r12: NFC register base. Doesn't change */
+ ldr r12, =IMX_NFC_REGS
+
+ ldr r11, =CONFIG_SYS_NAND_U_BOOT_DST
+
+ /* r13: end of SDRAM address for copying. Doesn't change */
+ add r13, r11, #CONFIG_SYS_NAND_U_BOOT_SIZE
+
+ /* r11: starting SDRAM address for copying. Updated constantly */
+ add r11, r11, r1
+
+ /* unlock internal buffer */
+ ldr r3, =NFC_CONFIG_UNLOCKED
+ strh r3, [r12, #NFC_OFFSET_CONFIG]
+
+ /* enable ECC and mask interrupts */
+ ldr r3, =(NFC_CONFIG1_ECC_EN | NFC_CONFIG1_INT_MSK)
+ strh r3, [r12, #NFC_OFFSET_CONFIG1]
+
+Nfc_Read_Page:
+ BOOT_TRACE(5)
+ /* send NAND_CMD_READ0 command */
+ ldr r3, =NAND_CMD_READ0;
+ strh r3, [r12, #NFC_OFFSET_FLASH_CMD]
+
+ ldr r3, =NFC_CONFIG2_FCMD
+ strh r3, [r12, #NFC_OFFSET_CONFIG2]
+ bl do_wait_op_done
+
+ /* send NAND address to read. TODO small page support */
+ BOOT_TRACE(6)
+ mov r3, r1, lsr #1
+ bl do_addr_input /* 1st addr cycle */
+
+ mov r3, r1, lsr #9
+ and r3, r3, #0x03
+ bl do_addr_input /* 2nd addr cycle */
+
+ mov r3, r1, lsr #11
+ bl do_addr_input /* 3rd addr cycle */
+
+ mov r3, r1, lsr #19
+ bl do_addr_input /* 4th addr cycle */
+
+ /* Small NAND flashs (== 1Gb) support 5 addr cycles */
+ mov r3, r1, lsr #27
+ bl do_addr_input /* 5th addr cycle */
+
+ /* send NAND_CMD_READSTART command. TODO small page support */
+ BOOT_TRACE(7)
+ mov r3, #NAND_CMD_READSTART;
+ strh r3, [r12, #NFC_OFFSET_FLASH_CMD]
+ mov r3, #NFC_CONFIG2_FCMD
+ strh r3, [r12, #NFC_OFFSET_CONFIG2]
+ bl do_wait_op_done
+
+ /* read and copy buf 0 */
+ BOOT_TRACE(8)
+ mov r3, #0
+ strh r3, [r12, #NFC_OFFSET_BUF_ADDR]
+
+ mov r3, #NFC_CONFIG2_FDO_PAGE
+ strh r3, [r12, #NFC_OFFSET_CONFIG2]
+ bl do_wait_op_done
+
+ bl Test_And_Copy_Buffer
+
+ /* read and copy buf 1 */
+ mov r3, #1
+ strh r3, [r12, #NFC_OFFSET_BUF_ADDR]
+
+ mov r3, #NFC_CONFIG2_FDO_PAGE
+ strh r3, [r12, #NFC_OFFSET_CONFIG2]
+ bl do_wait_op_done
+
+ bl Test_And_Copy_Buffer
+
+ /* here we should test if 512B page flash and bypass next buffers */
+ /* read and copy buf 2. TODO small page support */
+ mov r3, #2
+ strh r3, [r12, #NFC_OFFSET_BUF_ADDR]
+
+ mov r3, #NFC_CONFIG2_FDO_PAGE
+ strh r3, [r12, #NFC_OFFSET_CONFIG2]
+ bl do_wait_op_done
+
+ bl Test_And_Copy_Buffer
+
+ /* read and copy buf 3 */
+ mov r3, #3
+ strh r3, [r12, #NFC_OFFSET_BUF_ADDR]
+
+ mov r3, #NFC_CONFIG2_FDO_PAGE
+ strh r3, [r12, #NFC_OFFSET_CONFIG2]
+ bl do_wait_op_done
+
+ bl Test_And_Copy_Buffer
+
+ /* is the last page ? */
+ BOOT_TRACE(12)
+ cmp r11, r13
+ bge NAND_Copy_Main_done
+
+ /* r0: nfc base. Reloaded after each page copying */
+ ldr r0, =IMX_NFC_MAIN_AREA0
+ /* r2: end of 1st RAM buf. Doesn't change */
+ ldr r2, =IMX_NFC_MAIN_AREA1
+ b Nfc_Read_Page
+
+NAND_Copy_Main_done:
+ BOOT_TRACE(13)
+ .endm /* nand_boot */
+
+ .macro init_aipi
+ /*
+ * setup AIPI1 and AIPI2
+ */
+ write32 AIPI1_PSR0, ACFG_AIPI1_PSR0_VAL
+ write32 AIPI1_PSR1, ACFG_AIPI1_PSR1_VAL
+ write32 AIPI2_PSR0, ACFG_AIPI2_PSR0_VAL
+ write32 AIPI2_PSR1, ACFG_AIPI2_PSR1_VAL
+
+ /* Change SDRAM signal strengh */
+ ldr r0, =GPCR
+ ldr r1, =ACFG_GPCR_VAL
+ ldr r5, [r0]
+ orr r5, r5, r1
+ str r5, [r0]
+
+ .endm /* init_aipi */
+
+ .macro init_clock
+ ldr r0, =CSCR
+ /* disable MPLL/SPLL first */
+ ldr r1, [r0]
+ bic r1, r1, #(CSCR_MPEN|CSCR_SPEN)
+ str r1, [r0]
+
+ /*
+ * pll clock initialization predefined in apf27.h
+ */
+ write32 MPCTL0, ACFG_MPCTL0_VAL
+ write32 SPCTL0, ACFG_SPCTL0_VAL
+
+ write32 CSCR, ACFG_CSCR_VAL|CSCR_MPLL_RESTART|CSCR_SPLL_RESTART
+
+ /*
+ * add some delay here
+ */
+ mov r1, #0x1000
+ 1: subs r1, r1, #0x1
+ bne 1b
+
+ /* peripheral clock divider */
+ write32 PCDR0, ACFG_PCDR0_VAL
+ write32 PCDR1, ACFG_PCDR1_VAL
+
+ /* Configure PCCR0 and PCCR1 */
+ write32 PCCR0, ACFG_PCCR0_VAL
+ write32 PCCR1, ACFG_PCCR1_VAL
+
+ .endm /* init_clock */
+
+/*
+ *************************************************************************
+ *
+ * No jump vector table. Use reset vector as direct entry point.
+ * Do not support any interrupt event within SPL
+ *
+ *************************************************************************
+ */
+
+
+.globl _start
+_start:
+
+/*
+ *************************************************************************
+ *
+ * Startup Code (reset vector)
+ *
+ * do important init only if we don't start from memory!
+ * setup Memory and board specific bits prior to relocation.
+ * relocate armboot to ram
+ * setup stack
+ *
+ *************************************************************************
+ */
+
+
+/*
+ * the actual reset code
+ */
+
+reset:
+ /*
+ * set the cpu to SVC32 mode
+ */
+ mrs r0,cpsr
+ bic r0,r0,#0x1f
+ orr r0,r0,#0xd3
+ msr cpsr,r0
+
+ /*
+ * invalidate I/D cache/TLB and drain write buffer
+ */
+ mov r0, #0
+ mcr p15, 0, r0, c7, c7, 0 /* invalidate I cache and D cache */
+ mcr p15, 0, r0, c8, c7, 0 /* invalidate TLBs */
+ mcr p15, 0, r0, c7, c10, 4 /* Drain the write buffer */
+
+ /*
+ * disable MMU stuff and caches
+ */
+ mrc p15, 0, r0, c1, c0, 0
+ bic r0, r0, #0x00002300 /* clear bits 13, 9:8 (--V- --RS) */
+ bic r0, r0, #0x00000087 /* clear bits 7, 2:0 (B--- -CAM) */
+ orr r0, r0, #0x00000002 /* set bit 2 (A) Align */
+ orr r0, r0, #0x00001000 /* set bit 12 (I) I-Cache */
+ mcr p15, 0, r0, c1, c0, 0
+
+init_aipi_start:
+ init_aipi
+
+ /* check if sdram has been setup (running within sdram) */
+ cmp pc, #0xa0000000 /* start of first sdram memory space */
+ blo init_clock_start
+ cmp pc, #0xc0000000 /* end of second sdram memory space */
+ blo regular_boot
+
+ /* running from sdram with full code present -> regular_boot */
+init_clock_start:
+ init_clock
+
+init_sdram_start:
+ bl setup_sdram_ddr
+
+ /* save state of previous boot (SDRAM is configured)*/
+ BACKUP_TRACE()
+
+ /* nand_boot BOOT_TRACE(1..13) */
+
+ nand_boot
+
+ BOOT_TRACE(14) /* start regular U-Boot */
+
+regular_boot: /* jump to start of next 2kiB block (U-Boot) */
+ ldr r0, =0xfffff800
+ and r0, r0, pc
+ add pc, r0, #0x800
+
+do_wait_op_done:
+ 1:
+ ldrh r3, [r12, #NFC_OFFSET_CONFIG2]
+ ands r3, r3, #NFC_CONFIG2_INT
+ beq 1b
+ mov r3, #0x0
+ strh r3, [r12, #NFC_OFFSET_CONFIG2]
+ mov pc, lr
+
+do_addr_input:
+ mov r9, lr
+ and r3, r3, #0xFF
+ strh r3, [r12, #NFC_OFFSET_FLASH_ADDR]
+ mov r3, #NFC_CONFIG2_FADD
+ strh r3, [r12, #NFC_OFFSET_CONFIG2]
+ bl do_wait_op_done
+ mov pc, r9
+
+Test_And_Copy_Buffer:
+ /* check for bad block (2 bits error in main or spare are)*/
+ BOOT_TRACE(9)
+ ldrh r4, [r12, #NFC_OFFSET_ECC_STATUS_RESULT]
+ ands r4, r4, #(NFC_ECC_STAT_ERROR2| \
+ (NFC_ECC_STAT_ERROR2<<NFC_ECC_STAT_ERM_SHFT))
+ bne Skip_Bad_Buffer
+
+ /* check BI byte of the current spare buffer */
+ ldr r4, =IMX_NFC_SPARE_AREA0
+ ldrh r3, [r12, #NFC_OFFSET_BUF_ADDR] /* for the current buffer */
+ orr r4, r3, lsl #0x04
+
+ /* at bi word offset 4. */
+ /* Fixme position change betwwen 8 and 16 bits bus */
+ ldrh r4, [r4, #0x04]
+ and r4, r4, #0x0FF00 /* has to be 0xFFxx */
+ cmp r4, #0x0FF00
+ bne Skip_Bad_Buffer
+
+Copy_Good_Buffer:
+ /* copying 512 bytes buffer */
+ BOOT_TRACE(10)
+1: ldmia r0!, {r3-r10}
+ stmia r11!, {r3-r10}
+ cmp r0, r2
+ blo 1b
+ b End_Of_Copy
+
+Skip_Bad_Buffer:
+ BOOT_TRACE(11)
+ /* bad pages do not contain valid data and have to be skip */
+ add r0, r0, #0x200
+
+ /* rewind ram addr to start of buffer */
+ ldr r3, =(~0x1FF)
+ and r11, r11, r3
+
+End_Of_Copy:
+ add r2, r2, #0x200
+ add r1, r1, #0x200
+
+ mov pc, lr
+
+
+setup_sdram_ddr:
+
+ /* wait for SDRAM/LPDDR ready (SDRAMRDY) */
+ ldr r0, =IMX_ESD_BASE
+ ldr r4, =ESDMISC_SDRAM_RDY
+2: ldr r1, [r0, #ESDMISC_ROF]
+ ands r1, r1, r4
+ bpl 2b
+
+ /* LPDDR Soft Reset Mobile/Low Power DDR SDRAM. */
+ ldr r0, =IMX_ESD_BASE
+ ldr r4, =ACFG_ESDMISC_VAL
+ orr r1, r4, #ESDMISC_MDDR_DL_RST
+ str r1, [r0, #ESDMISC_ROF]
+
+ /* Hold for more than 200ns */
+ ldr r1, =0x10000
+ 1: subs r1, r1, #0x1
+ bne 1b
+
+ str r4, [r0]
+
+ /* write32(ESDCFG0, ACFG_SDRAM_ESDCFG_REGISTER_VAL) */
+ ldr r0, =IMX_ESD_BASE
+ ldr r1, =ACFG_SDRAM_ESDCFG_REGISTER_VAL
+ str r1, [r0, #ESDCFG0_ROF]
+
+ /* write32(ESDCTL0, ACFG_PRECHARGE_CMD) */
+ ldr r0, =IMX_ESD_BASE
+ ldr r1, =ACFG_PRECHARGE_CMD
+ str r1, [r0, #ESDCTL0_ROF]
+
+ /* write8(0xA0001000, any value) */
+ ldr r1, =PHYS_SDRAM_1+ACFG_SDRAM_PRECHARGE_ALL_VAL
+ strb r2, [r1]
+
+ /* write32(ESDCTL0, ACFG_AUTOREFRESH_CMD) */
+ ldr r1, =ACFG_AUTOREFRESH_CMD
+ str r1, [r0, #ESDCTL0_ROF]
+
+ ldr r4, =PHYS_SDRAM_1 /* CSD0 base address */
+
+ ldr r6,=0x7 /* load loop counter */
+1: str r5,[r4] /* run auto-refresh cycle to array 0 */
+ subs r6,r6,#1 /* decrease counter value */
+ bne 1b
+
+ /* write32(ACFG_PRECHARGE_CMD, ACFG_SET_MODE_REG_CMD) */
+ ldr r1, =ACFG_SET_MODE_REG_CMD
+ str r1, [r0, #ESDCTL0_ROF]
+
+ /* set standard mode register */
+ ldr r4, = PHYS_SDRAM_1+ACFG_SDRAM_MODE_REGISTER_VAL
+ strb r2, [r4]
+
+ /* set extended mode register */
+ ldr r4, =PHYS_SDRAM_1+ACFG_SDRAM_EXT_MODE_REGISTER_VAL
+ strb r5, [r4]
+
+ /* write32(ACFG_PRECHARGE_CMD, ACFG_NORMAL_RW_CMD) */
+ ldr r1, =ACFG_NORMAL_RW_CMD
+ str r1, [r0, #ESDCTL0_ROF]
+
+ /* 2nd sdram */
+ /* write32(ESDCFG1, ACFG_SDRAM_ESDCFG_REGISTER_VAL ) */
+ ldr r0, =IMX_ESD_BASE
+ ldr r1, =ACFG_SDRAM_ESDCFG_REGISTER_VAL
+ str r1, [r0, #ESDCFG1_ROF]
+
+ /* write32(ESDCTL1, ACFG_PRECHARGE_CMD) */
+ ldr r0, =IMX_ESD_BASE
+ ldr r1, =ACFG_PRECHARGE_CMD
+ str r1, [r0, #ESDCTL1_ROF]
+
+ /* write8(0xB0001000, any value) */
+ ldr r1, =PHYS_SDRAM_2+ACFG_SDRAM_PRECHARGE_ALL_VAL
+ strb r2, [r1]
+
+ /* write32(ESDCTL1, ACFG_AUTOREFRESH_CMD) */
+ ldr r1, =ACFG_AUTOREFRESH_CMD
+ str r1, [r0, #ESDCTL1_ROF]
+
+ ldr r4, =PHYS_SDRAM_2 /* CSD1 base address */
+
+ ldr r6,=0x7 /* load loop counter */
+1: str r5,[r4] /* run auto-refresh cycle to array 0 */
+ subs r6,r6,#1 /* decrease counter value */
+ bne 1b
+
+ /* write32(ESDCTL1, ACFG_SET_MODE_REG_CMD) */
+ ldr r1, =ACFG_SET_MODE_REG_CMD
+ str r1, [r0, #ESDCTL1_ROF]
+
+ /* set standard mode register */
+ ldr r4, =PHYS_SDRAM_2+ACFG_SDRAM_MODE_REGISTER_VAL
+ strb r2, [r4]
+
+ /* set extended mode register */
+ ldr r4, =PHYS_SDRAM_2+ACFG_SDRAM_EXT_MODE_REGISTER_VAL
+ strb r2, [r4]
+
+ /* write32(ESDCTL1, ACFG_NORMAL_RW_CMD) */
+ ldr r1, =ACFG_NORMAL_RW_CMD
+ str r1, [r0, #ESDCTL1_ROF]
+
+ mov pc, lr
+
diff --git a/board/armadeus/apf27/u-boot-spl.lds b/board/armadeus/apf27/u-boot-spl.lds
new file mode 100644
index 0000000..fdd52f2
--- /dev/null
+++ b/board/armadeus/apf27/u-boot-spl.lds
@@ -0,0 +1,87 @@
+/*
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ * January 2004 - Changed to support H4 device
+ * Copyright (c) 2004-2008 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0xA0fff800;
+
+ . = ALIGN(4);
+ .text :
+ {
+ board/armadeus/apf27/start.o (.text)
+ *(.text)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+ . = ALIGN(4);
+ .data : {
+ *(.data)
+ }
+
+ . = ALIGN(4);
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = ALIGN(4);
+
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ }
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ }
+
+ .bss : {
+ . = ALIGN(4);
+ __bss_start = .;
+ *(.bss*)
+ . = ALIGN(4);
+ __bss_end__ = .;
+ }
+
+ _end = .;
+
+ /DISCARD/ : { *(.dynstr*) }
+ /DISCARD/ : { *(.dynsym*) }
+ /DISCARD/ : { *(.dynamic*) }
+ /DISCARD/ : { *(.hash*) }
+ /DISCARD/ : { *(.plt*) }
+ /DISCARD/ : { *(.interp*) }
+ /DISCARD/ : { *(.gnu*) }
+}
--
1.7.4.4
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 4/4] apf27: add FPGA support for the apf27 board
2012-10-29 17:35 [U-Boot] [PATCH 0/4] apf27: add support of armadeus apf27 v2 Philippe Reynes
` (2 preceding siblings ...)
2012-10-29 17:35 ` [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27 Philippe Reynes
@ 2012-10-29 17:35 ` Philippe Reynes
3 siblings, 0 replies; 10+ messages in thread
From: Philippe Reynes @ 2012-10-29 17:35 UTC (permalink / raw)
To: u-boot
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
create mode 100644 board/armadeus/apf27/fpga.c
create mode 100644 board/armadeus/apf27/fpga.h
diff --git a/board/armadeus/apf27/Makefile b/board/armadeus/apf27/Makefile
index f57f405..9d356a3 100644
--- a/board/armadeus/apf27/Makefile
+++ b/board/armadeus/apf27/Makefile
@@ -29,6 +29,9 @@ LIB = $(obj)lib$(BOARD).o
ifndef CONFIG_SPL_BUILD
COBJS := apf27.o
+ifdef CONFIG_FPGA
+COBJS += fpga.o
+endif
endif
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
diff --git a/board/armadeus/apf27/apf27.c b/board/armadeus/apf27/apf27.c
index 4f2b821..502bc8e 100644
--- a/board/armadeus/apf27/apf27.c
+++ b/board/armadeus/apf27/apf27.c
@@ -21,6 +21,7 @@
#include <common.h>
#include "crc.h"
+#include "fpga.h"
#include <jffs2/jffs2.h>
#include <nand.h>
#include <netdev.h>
@@ -371,6 +372,21 @@ misc_init_r(void)
struct mtd_device *dev;
struct part_info *part;
+#if defined(CONFIG_FPGA)
+ /* init and download fpga */
+ if ((autoload) && (0 == strcmp(autoload, "1"))) {
+ if (mtdparts_init() == 0)
+ if (find_dev_and_part("firmware",
+ &dev, &pnum, &part) == 0) {
+ size = part->size;
+ if (nand_read_skip_bad(&nand_info[0],
+ part->offset, &size, firmware_buffer))
+ size = 0;
+ }
+ }
+ APF27_init_fpga(firmware_buffer, size);
+#endif
+
/* detect compatibility issue of environment version */
s = getenv("env_version");
if ((NULL == s) || (0 != strcmp(s, CONFIG_ENV_VERSION))) {
diff --git a/board/armadeus/apf27/fpga.c b/board/armadeus/apf27/fpga.c
new file mode 100644
index 0000000..d5c27a7
--- /dev/null
+++ b/board/armadeus/apf27/fpga.c
@@ -0,0 +1,262 @@
+/*
+ * (C) Copyright 2002-2012
+ * Eric Jarrige <eric.jarrige@armadeus.org>
+ * Rich Ireland, Enterasys Networks, rireland at enterasys.com.
+ * Keith Outwater, keith_outwater at mvis.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+#include <common.h>
+
+#include <asm/arch/imx-regs.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <command.h>
+#include <config.h>
+#include "fpga.h"
+#include <spartan3.h>
+#include "apf27.h"
+
+/*
+ * Note that these are pointers to code that is in Flash. They will be
+ * relocated at runtime.
+ * Spartan2 code is used to download our Spartan 3 :) code is compatible.
+ * Just take care about the file size
+ */
+Xilinx_Spartan3_Slave_Parallel_fns fpga_fns = {
+ fpga_pre_fn,
+ fpga_pgm_fn,
+ fpga_init_fn,
+ NULL,
+ fpga_done_fn,
+ fpga_clk_fn,
+ fpga_cs_fn,
+ fpga_wr_fn,
+ fpga_rdata_fn,
+ fpga_wdata_fn,
+ fpga_busy_fn,
+ fpga_abort_fn,
+ fpga_post_fn,
+};
+
+Xilinx_desc fpga[CONFIG_FPGA_COUNT] = {
+ {Xilinx_Spartan3,
+ slave_parallel,
+ 1196128l/8,
+ (void *) &fpga_fns,
+ 0}
+};
+
+/*
+ * Initialize GPIO port B before download
+ */
+int
+fpga_pre_fn(int cookie)
+{
+ /* Initialize GPIO pins */
+ gpio_set_value(ACFG_FPGA_PWR, 1);
+ imx_gpio_mode(ACFG_FPGA_INIT | GPIO_IN | GPIO_PUEN | GPIO_GPIO);
+ imx_gpio_mode(ACFG_FPGA_DONE | GPIO_IN | GPIO_PUEN | GPIO_GPIO);
+ imx_gpio_mode(ACFG_FPGA_PRG | GPIO_OUT | GPIO_PUEN | GPIO_GPIO);
+ imx_gpio_mode(ACFG_FPGA_CLK | GPIO_OUT | GPIO_PUEN | GPIO_GPIO);
+ imx_gpio_mode(ACFG_FPGA_RW | GPIO_OUT | GPIO_PUEN | GPIO_GPIO);
+ imx_gpio_mode(ACFG_FPGA_CS | GPIO_OUT | GPIO_PUEN | GPIO_GPIO);
+ imx_gpio_mode(ACFG_FPGA_SUSPEND|GPIO_OUT|GPIO_PUEN|GPIO_GPIO);
+ gpio_set_value(ACFG_FPGA_RESET, 1);
+ imx_gpio_mode(ACFG_FPGA_RESET | GPIO_OUT | GPIO_PUEN | GPIO_GPIO);
+ imx_gpio_mode(ACFG_FPGA_PWR | GPIO_OUT | GPIO_PUEN | GPIO_GPIO);
+ gpio_set_value(ACFG_FPGA_PRG, 1);
+ gpio_set_value(ACFG_FPGA_CLK, 1);
+ gpio_set_value(ACFG_FPGA_RW, 1);
+ gpio_set_value(ACFG_FPGA_CS, 1);
+ gpio_set_value(ACFG_FPGA_SUSPEND, 0);
+ gpio_set_value(ACFG_FPGA_PWR, 0);
+
+ return cookie;
+}
+
+/*
+ * Set the FPGA's active-low program line to the specified level
+ */
+int
+fpga_pgm_fn(int assert, int flush, int cookie)
+{
+ debug("%s:%d: FPGA PROGRAM %s", __func__, __LINE__,
+ assert ? "high" : "low");
+ gpio_set_value(ACFG_FPGA_PRG, !assert);
+ return assert;
+}
+
+/*
+ * Set the FPGA's active-high clock line to the specified level
+ */
+int
+fpga_clk_fn(int assert_clk, int flush, int cookie)
+{
+ debug("%s:%d: FPGA CLOCK %s", __func__, __LINE__,
+ assert_clk ? "high" : "low");
+ gpio_set_value(ACFG_FPGA_CLK, !assert_clk);
+ return assert_clk;
+}
+
+/*
+ * Test the state of the active-low FPGA INIT line. Return 1 on INIT
+ * asserted (low).
+ */
+int
+fpga_init_fn(int cookie)
+{
+ int value;
+ debug("%s:%d: INIT check... ", __func__, __LINE__);
+ value = gpio_get_value(ACFG_FPGA_INIT);
+ /* printf("init value read %x",value); */
+#ifdef CONFIG_SYS_FPGA_IS_PROTO
+ return value;
+#else
+ return !value;
+#endif
+}
+
+/*
+ * Test the state of the active-high FPGA DONE pin
+ */
+int
+fpga_done_fn(int cookie)
+{
+ debug("%s:%d: DONE check... %s", __func__, __LINE__,
+ gpio_get_value(ACFG_FPGA_DONE) ? "high" : "low");
+ return gpio_get_value(ACFG_FPGA_DONE) ? FPGA_SUCCESS : FPGA_FAIL;
+}
+
+/*
+ * Set the FPGA's wr line to the specified level
+ */
+int
+fpga_wr_fn(int assert_write, int flush, int cookie)
+{
+ debug("%s:%d: FPGA RW... %s ", __func__, __LINE__,
+ assert_write ? "high" : "low");
+ gpio_set_value(ACFG_FPGA_RW, !assert_write);
+ return assert_write;
+}
+
+int
+fpga_cs_fn(int assert_cs, int flush, int cookie)
+{
+ debug("%s:%d: FPGA CS %s ", __func__, __LINE__,
+ assert_cs ? "high" : "low");
+ gpio_set_value(ACFG_FPGA_CS, !assert_cs);
+ return assert_cs;
+}
+
+int
+fpga_rdata_fn(unsigned char *data, int cookie)
+{
+ debug("%s:%d: FPGA READ DATA %02X ", __func__, __LINE__,
+ *((char *)ACFG_FPGA_RDATA));
+ *data = (unsigned char) \
+ ((*((unsigned short *)ACFG_FPGA_RDATA))&0x00FF);
+ return *data;
+}
+
+int
+fpga_wdata_fn(unsigned char data, int cookie)
+{
+ debug("%s:%d: FPGA WRITE DATA %02X ", __func__, __LINE__,
+ data);
+ *((unsigned short *)ACFG_FPGA_WDATA) = data;
+ return data;
+}
+
+int
+fpga_abort_fn(int cookie)
+{
+ return cookie;
+}
+
+
+int
+fpga_busy_fn(int cookie)
+{
+ return 1;
+}
+
+int
+fpga_post_fn(int cookie)
+{
+ debug("%s:%d: FPGA POST ", __func__, __LINE__);
+
+ imx_gpio_mode(ACFG_FPGA_RW | GPIO_PF | GPIO_PUEN);
+ imx_gpio_mode(ACFG_FPGA_CS | GPIO_PF | GPIO_PUEN);
+ imx_gpio_mode(ACFG_FPGA_CLK | GPIO_PF | GPIO_PUEN);
+ gpio_set_value(ACFG_FPGA_PRG, 1);
+ gpio_set_value(ACFG_FPGA_RESET, 0);
+ imx_gpio_mode(ACFG_FPGA_RESET | GPIO_OUT | GPIO_PUEN | GPIO_GPIO);
+ return cookie;
+}
+
+void apf27_fpga_setup(void)
+{
+ struct pll_regs *pll = (struct pll_regs *)IMX_PLL_BASE;
+ struct system_control_regs *system = \
+ (struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
+
+ /* Configure FPGA CLKO */
+ writel(ACFG_CCSR_VAL, &pll->ccsr);
+
+ /* Configure strentgh for FPGA */
+ writel(ACFG_DSCR10_VAL, &system->dscr10);
+ writel(ACFG_DSCR3_VAL, &system->dscr3);
+ writel(ACFG_DSCR7_VAL, &system->dscr7);
+ writel(ACFG_DSCR2_VAL, &system->dscr2);
+}
+
+/*
+ * Initialize the fpga. Return 1 on success, 0 on failure.
+ */
+int
+APF27_init_fpga(u_char *buffer, size_t size)
+{
+ char *autoload = getenv("firmware_autoload");
+
+ int i, lout = 0;
+
+ apf27_fpga_setup();
+
+ fpga_init();
+
+ for (i = 0; i < CONFIG_FPGA_COUNT; i++) {
+ debug("%s:%d: Adding fpga %d\n", __func__, __LINE__, i);
+ fpga_add(fpga_xilinx, &fpga[i]);
+ }
+
+ if ((size >= fpga[0].size) && (autoload) &&
+ (0 == strcmp(autoload, "1"))) {
+ if (ctrlc()) {
+ printf("Firmware download stopped!\n");
+ } else if (FPGA_SUCCESS != fpga_load(0, (void *)buffer, size)) {
+ printf("Firmware download failed!\n");
+ } else {
+ printf("Firmware successfully programmed\n");
+ lout = 1;
+ }
+ }
+ return lout;
+}
diff --git a/board/armadeus/apf27/fpga.h b/board/armadeus/apf27/fpga.h
new file mode 100644
index 0000000..b11b24c
--- /dev/null
+++ b/board/armadeus/apf27/fpga.h
@@ -0,0 +1,39 @@
+/*
+ * (C) Copyright 2002-2012
+ * Eric Jarrige <eric.jarrige@armadeus.org>
+ * Rich Ireland, Enterasys Networks, rireland at enterasys.com.
+ * Keith Outwater, keith_outwater at mvis.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+extern int APF27_init_fpga(u_char *buffer, size_t size);
+
+extern int fpga_pre_fn(int cookie);
+extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
+extern int fpga_cs_fn(int assert_cs, int flush, int cookie);
+extern int fpga_init_fn(int cookie);
+extern int fpga_done_fn(int cookie);
+extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
+extern int fpga_wr_fn(int assert_write, int flush, int cookie);
+extern int fpga_rdata_fn(unsigned char *data, int cookie);
+extern int fpga_wdata_fn(unsigned char data, int cookie);
+extern int fpga_abort_fn(int cookie);
+extern int fpga_post_fn(int cookie);
+extern int fpga_busy_fn(int cookie);
--
1.7.4.4
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27
2012-10-29 17:35 ` [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27 Philippe Reynes
@ 2012-10-30 20:50 ` Fabio Estevam
2012-11-26 18:02 ` Albert ARIBAUD
1 sibling, 0 replies; 10+ messages in thread
From: Fabio Estevam @ 2012-10-30 20:50 UTC (permalink / raw)
To: u-boot
On Mon, Oct 29, 2012 at 3:35 PM, Philippe Reynes <tremyfr@yahoo.fr> wrote:
> --- /dev/null
> +++ b/board/armadeus/apf27/start.S
> @@ -0,0 +1,549 @@
> +/*
> + * IMX27 NAND Flash SPL (Secondary Program Loader)
> + *
> + * Copyright (c) 2008 Armadeus Project / eja
> + *
> + * Based on Freescale NAND SPL
Shouldn't this start.S file be placed on some common location rather
than board/armadeus directory?
Regards,
Fabio Estevam
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 2/4] apf27: add support for the armadeus APF27 board
2012-10-29 17:35 ` [U-Boot] [PATCH 2/4] apf27: add support for the armadeus APF27 board Philippe Reynes
@ 2012-11-26 17:55 ` Albert ARIBAUD
2012-12-02 17:07 ` trem
0 siblings, 1 reply; 10+ messages in thread
From: Albert ARIBAUD @ 2012-11-26 17:55 UTC (permalink / raw)
To: u-boot
Hi Philippe,
On Mon, 29 Oct 2012 18:35:55 +0100, Philippe Reynes <tremyfr@yahoo.fr>
wrote:
> Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
> Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
> Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
>
> create mode 100644 board/armadeus/apf27/Makefile
> create mode 100644 board/armadeus/apf27/apf27.c
> create mode 100644 board/armadeus/apf27/apf27.h
> create mode 100644 include/configs/apf27.h
This patch alone barely supports APF27, since the resulting U-Boot
cannot be flashed on the board and booted cold; for this it needs the
SPL from patch 3/4. Please merge 2/4 and 3/4.
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 1b2da94..297467a 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1011,6 +1011,11 @@ Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
>
> armadillo-800eva R8A7740 (RMOBILE SoC)
>
> +Eric Jarrige <eric.jarrige@armadeus.org>
> +Philippe Reynes <tremyfr@yahoo.fr>
> +
> + apf27 ARM926EJS (imx27 SoC)
> +
> -------------------------------------------------------------------------
>
> Unknown / orphaned boards:
Please sort MAINTAINERS by maintainer name as stated in the file
heading.
> diff --git a/board/armadeus/apf27/Makefile b/board/armadeus/apf27/Makefile
> new file mode 100644
> index 0000000..1da9548
> --- /dev/null
> +++ b/board/armadeus/apf27/Makefile
> @@ -0,0 +1,45 @@
> +#
> +# (C) Copyright 2000-2004
> +# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> +# (C) Copyright 2012
> +# Eric Jarrige <eric.jarrige@armadeus.org>
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program; if not, write to the Free Software
> +# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> +# MA 02111-1307 USA
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB = $(obj)lib$(BOARD).o
> +
> +COBJS := apf27.o
> +
> +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS))
> +SOBJS := $(addprefix $(obj),$(SOBJS))
> +
> +$(LIB): $(obj).depend $(OBJS) $(SOBJS)
> + $(call cmd_link_o_target, $(OBJS) $(SOBJS))
> +
> +#########################################################################
> +
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#########################################################################
> diff --git a/board/armadeus/apf27/apf27.c b/board/armadeus/apf27/apf27.c
> new file mode 100644
> index 0000000..4f2b821
> --- /dev/null
> +++ b/board/armadeus/apf27/apf27.c
> @@ -0,0 +1,408 @@
> +/*
> + * Copyright (C) 2007 Sascha Hauer, Pengutronix
> + * Copyright (C) 2008-2012 Eric Jarrige <eric.jarrige@armadeus.org>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + *
> + */
> +
> +#include <common.h>
> +#include "crc.h"
> +#include <jffs2/jffs2.h>
> +#include <nand.h>
> +#include <netdev.h>
> +#include <asm/io.h>
> +#include <asm/arch/imx-regs.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/errno.h>
> +#include <environment.h>
> +#include "apf27.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +/*
> + * Fuse bank 1 row 8 is "reserved for future use" and therefore available for
> + * custormer use. The APF27 board uses this fuse to store the board revision:
> + * 0: initial board revision
> + * 1: first revision - Presence of the second RAM chip on the board is blown in
> + * fuse bank 1 row 9 bit 0 - No hardware change
> + * N: to be defined
(aside: I am somewhat surprised that something "reserved for future
use" can be considered "available for customer use": reserved areas
are... reserved... thus probably not available -- future revisions of
the *IC* may actually exercize the reservation, causing a conflict
with the *board* assumptions. But hey, that's not a U-boot issue)
> + */
> +u32 get_board_rev(void)
> +{
> + struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
> +
> + return readl(&iim->bank[1].fuse_regs[8]);
> +}
> +
> +/*
> + * Fuse bank 1 row 9 is "reserved for future use" and therefore available for
> + * custormer use. The APF27 board revision 1 uses the bit 0 to permanently store
> + * the presence of the second RAM chip
> + * 0: AFP27 with 1 RAM of 64 MiB
> + * 1: AFP27 with 2 RAM chips of 64 MiB each (128MB)
> + */
> +int get_num_ram_bank(void)
> +{
> + struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
> + int nr_dram_banks = 1;
> +
> + if ((get_board_rev() > 0) && (CONFIG_NR_DRAM_BANKS > 1))
> + nr_dram_banks += readl(&iim->bank[1].fuse_regs[9]) & 0x01;
> + else
> + nr_dram_banks = CONFIG_NR_DRAM_POPULATED;
> +
> + return nr_dram_banks;
> +}
> +
> +static void apf27_gpio_init(void)
> +{
> + struct gpio_port_regs *regs = (struct gpio_port_regs *)IMX_GPIO_BASE;
> +
> + /* PORT A */
> + writel(ACFG_DR_A_VAL, ®s->port[PORTA].gpio_dr);
> + writel(ACFG_OCR1_A_VAL, ®s->port[PORTA].ocr1);
> + writel(ACFG_OCR2_A_VAL, ®s->port[PORTA].ocr2);
> + writel(ACFG_ICFA1_A_VAL, ®s->port[PORTA].iconfa1);
> + writel(ACFG_ICFA2_A_VAL, ®s->port[PORTA].iconfa2);
> + writel(ACFG_ICFB1_A_VAL, ®s->port[PORTA].iconfb1);
> + writel(ACFG_ICFB2_A_VAL, ®s->port[PORTA].iconfb2);
> + writel(ACFG_ICR1_A_VAL, ®s->port[PORTA].icr1);
> + writel(ACFG_ICR2_A_VAL, ®s->port[PORTA].icr2);
> + writel(ACFG_IMR_A_VAL, ®s->port[PORTA].imr);
> + writel(ACFG_DDIR_A_VAL, ®s->port[PORTA].gpio_dir);
> + writel(ACFG_GPR_A_VAL, ®s->port[PORTA].gpr);
> + writel(ACFG_PUEN_A_VAL, ®s->port[PORTA].puen);
> + writel(ACFG_GIUS_A_VAL, ®s->port[PORTA].gius);
> +
> + /* PORT B */
> + writel(ACFG_DR_B_VAL, ®s->port[PORTB].gpio_dr);
> + writel(ACFG_OCR1_B_VAL, ®s->port[PORTB].ocr1);
> + writel(ACFG_OCR2_B_VAL, ®s->port[PORTB].ocr2);
> + writel(ACFG_ICFA1_B_VAL, ®s->port[PORTB].iconfa1);
> + writel(ACFG_ICFA2_B_VAL, ®s->port[PORTB].iconfa2);
> + writel(ACFG_ICFB1_B_VAL, ®s->port[PORTB].iconfb1);
> + writel(ACFG_ICFB2_B_VAL, ®s->port[PORTB].iconfb2);
> + writel(ACFG_ICR1_B_VAL, ®s->port[PORTB].icr1);
> + writel(ACFG_ICR2_B_VAL, ®s->port[PORTB].icr2);
> + writel(ACFG_IMR_B_VAL, ®s->port[PORTB].imr);
> + writel(ACFG_DDIR_B_VAL, ®s->port[PORTB].gpio_dir);
> + writel(ACFG_GPR_B_VAL, ®s->port[PORTB].gpr);
> + writel(ACFG_PUEN_B_VAL, ®s->port[PORTB].puen);
> + writel(ACFG_GIUS_B_VAL, ®s->port[PORTB].gius);
> +
> + /* PORT C */
> + writel(ACFG_DR_C_VAL, ®s->port[PORTC].gpio_dr);
> + writel(ACFG_OCR1_C_VAL, ®s->port[PORTC].ocr1);
> + writel(ACFG_OCR2_C_VAL, ®s->port[PORTC].ocr2);
> + writel(ACFG_ICFA1_C_VAL, ®s->port[PORTC].iconfa1);
> + writel(ACFG_ICFA2_C_VAL, ®s->port[PORTC].iconfa2);
> + writel(ACFG_ICFB1_C_VAL, ®s->port[PORTC].iconfb1);
> + writel(ACFG_ICFB2_C_VAL, ®s->port[PORTC].iconfb2);
> + writel(ACFG_ICR1_C_VAL, ®s->port[PORTC].icr1);
> + writel(ACFG_ICR2_C_VAL, ®s->port[PORTC].icr2);
> + writel(ACFG_IMR_C_VAL, ®s->port[PORTC].imr);
> + writel(ACFG_DDIR_C_VAL, ®s->port[PORTC].gpio_dir);
> + writel(ACFG_GPR_C_VAL, ®s->port[PORTC].gpr);
> + writel(ACFG_PUEN_C_VAL, ®s->port[PORTC].puen);
> + writel(ACFG_GIUS_C_VAL, ®s->port[PORTC].gius);
> +
> + /* PORT D */
> + writel(ACFG_DR_D_VAL, ®s->port[PORTD].gpio_dr);
> + writel(ACFG_OCR1_D_VAL, ®s->port[PORTD].ocr1);
> + writel(ACFG_OCR2_D_VAL, ®s->port[PORTD].ocr2);
> + writel(ACFG_ICFA1_D_VAL, ®s->port[PORTD].iconfa1);
> + writel(ACFG_ICFA2_D_VAL, ®s->port[PORTD].iconfa2);
> + writel(ACFG_ICFB1_D_VAL, ®s->port[PORTD].iconfb1);
> + writel(ACFG_ICFB2_D_VAL, ®s->port[PORTD].iconfb2);
> + writel(ACFG_ICR1_D_VAL, ®s->port[PORTD].icr1);
> + writel(ACFG_ICR2_D_VAL, ®s->port[PORTD].icr2);
> + writel(ACFG_IMR_D_VAL, ®s->port[PORTD].imr);
> + writel(ACFG_DDIR_D_VAL, ®s->port[PORTD].gpio_dir);
> + writel(ACFG_GPR_D_VAL, ®s->port[PORTD].gpr);
> + writel(ACFG_PUEN_D_VAL, ®s->port[PORTD].puen);
> + writel(ACFG_GIUS_D_VAL, ®s->port[PORTD].gius);
> +
> + /* PORT E */
> + writel(ACFG_DR_E_VAL, ®s->port[PORTE].gpio_dr);
> + writel(ACFG_OCR1_E_VAL, ®s->port[PORTE].ocr1);
> + writel(ACFG_OCR2_E_VAL, ®s->port[PORTE].ocr2);
> + writel(ACFG_ICFA1_E_VAL, ®s->port[PORTE].iconfa1);
> + writel(ACFG_ICFA2_E_VAL, ®s->port[PORTE].iconfa2);
> + writel(ACFG_ICFB1_E_VAL, ®s->port[PORTE].iconfb1);
> + writel(ACFG_ICFB2_E_VAL, ®s->port[PORTE].iconfb2);
> + writel(ACFG_ICR1_E_VAL, ®s->port[PORTE].icr1);
> + writel(ACFG_ICR2_E_VAL, ®s->port[PORTE].icr2);
> + writel(ACFG_IMR_E_VAL, ®s->port[PORTE].imr);
> + writel(ACFG_DDIR_E_VAL, ®s->port[PORTE].gpio_dir);
> + writel(ACFG_GPR_E_VAL, ®s->port[PORTE].gpr);
> + writel(ACFG_PUEN_E_VAL, ®s->port[PORTE].puen);
> + writel(ACFG_GIUS_E_VAL, ®s->port[PORTE].gius);
> +
> + /* PORT F */
> + writel(ACFG_DR_F_VAL, ®s->port[PORTF].gpio_dr);
> + writel(ACFG_OCR1_F_VAL, ®s->port[PORTF].ocr1);
> + writel(ACFG_OCR2_F_VAL, ®s->port[PORTF].ocr2);
> + writel(ACFG_ICFA1_F_VAL, ®s->port[PORTF].iconfa1);
> + writel(ACFG_ICFA2_F_VAL, ®s->port[PORTF].iconfa2);
> + writel(ACFG_ICFB1_F_VAL, ®s->port[PORTF].iconfb1);
> + writel(ACFG_ICFB2_F_VAL, ®s->port[PORTF].iconfb2);
> + writel(ACFG_ICR1_F_VAL, ®s->port[PORTF].icr1);
> + writel(ACFG_ICR2_F_VAL, ®s->port[PORTF].icr2);
> + writel(ACFG_IMR_F_VAL, ®s->port[PORTF].imr);
> + writel(ACFG_DDIR_F_VAL, ®s->port[PORTF].gpio_dir);
> + writel(ACFG_GPR_F_VAL, ®s->port[PORTF].gpr);
> + writel(ACFG_PUEN_F_VAL, ®s->port[PORTF].puen);
> + writel(ACFG_GIUS_F_VAL, ®s->port[PORTF].gius);
> +}
Wouldn't it simplify the code to create a function that initializes one
port passed as an argument with an array of consts passed as a second
argument, then define 6 consts for the 6 ports and call the function 6
times with the right arguments?
> +
> +static int apf27_devices_init(void)
> +{
> + struct gpio_port_regs *regs = (struct gpio_port_regs *)IMX_GPIO_BASE;
> + int i;
> + unsigned int mode[] = {
> + PD0_AIN_FEC_TXD0,
> + PD1_AIN_FEC_TXD1,
> + PD2_AIN_FEC_TXD2,
> + PD3_AIN_FEC_TXD3,
> + PD4_AOUT_FEC_RX_ER,
> + PD5_AOUT_FEC_RXD1,
> + PD6_AOUT_FEC_RXD2,
> + PD7_AOUT_FEC_RXD3,
> + PD8_AF_FEC_MDIO,
> + PD9_AIN_FEC_MDC | GPIO_PUEN,
> + PD10_AOUT_FEC_CRS,
> + PD11_AOUT_FEC_TX_CLK,
> + PD12_AOUT_FEC_RXD0,
> + PD13_AOUT_FEC_RX_DV,
> + PD14_AOUT_FEC_CLR,
> + PD15_AOUT_FEC_COL,
> + PD16_AIN_FEC_TX_ER,
> + PF23_AIN_FEC_TX_EN,
> + PE12_PF_UART1_TXD,
> + PE13_PF_UART1_RXD,
> + };
> +
> + for (i = 0; i < ARRAY_SIZE(mode); i++)
> + imx_gpio_mode(mode[i]);
> +
> +#ifdef CONFIG_MXC_MMC
> + mx27_sd2_init_pins();
> + imx_gpio_mode((GPIO_PORTF | GPIO_OUT | GPIO_PUEN | GPIO_GPIO | 16));
> + writel(readl(®s->port[PORTF].gpio_dr) | (1 << 16),
> + ®s->port[PORTF].gpio_dr);
> +#endif
> + return 0;
> +}
> +
> +static void board_setup_aipi(void)
> +{
> + struct aipi_regs *aipi1 = (struct aipi_regs *)IMX_AIPI1_BASE;
> + struct aipi_regs *aipi2 = (struct aipi_regs *)IMX_AIPI2_BASE;
> + struct system_control_regs *system = \
> + (struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
> + u32 gpcr;
> +
> + /* setup AIPI1 and AIPI2 */
> + writel(ACFG_AIPI1_PSR0_VAL, &aipi1->psr0);
> + writel(ACFG_AIPI1_PSR1_VAL, &aipi1->psr1);
> + writel(ACFG_AIPI2_PSR0_VAL, &aipi2->psr0);
> + writel(ACFG_AIPI2_PSR1_VAL, &aipi2->psr1);
> +
> + /* Change SDRAM signal strengh */
> + gpcr = readl(&system->gpcr);
> + gpcr |= ACFG_GPCR_VAL;
> + writel(gpcr, &system->gpcr);
> +}
> +
> +static void board_setup_csx(void)
> +{
> + struct weim_regs *weim = (struct weim_regs *)IMX_WEIM_BASE;
> +
> + writel(ACFG_CS0U_VAL, &weim->cs0u);
> + writel(ACFG_CS0L_VAL, &weim->cs0l);
> + writel(ACFG_CS0A_VAL, &weim->cs0a);
> +
> + writel(ACFG_CS1U_VAL, &weim->cs1u);
> + writel(ACFG_CS1L_VAL, &weim->cs1l);
> + writel(ACFG_CS1A_VAL, &weim->cs1a);
> +
> + writel(ACFG_CS2U_VAL, &weim->cs2u);
> + writel(ACFG_CS2L_VAL, &weim->cs2l);
> + writel(ACFG_CS2A_VAL, &weim->cs2a);
> +
> + writel(ACFG_CS3U_VAL, &weim->cs3u);
> + writel(ACFG_CS3L_VAL, &weim->cs3l);
> + writel(ACFG_CS3A_VAL, &weim->cs3a);
> +
> + writel(ACFG_CS4U_VAL, &weim->cs4u);
> + writel(ACFG_CS4L_VAL, &weim->cs4l);
> + writel(ACFG_CS4A_VAL, &weim->cs4a);
> +
> + writel(ACFG_CS5U_VAL, &weim->cs5u);
> + writel(ACFG_CS5L_VAL, &weim->cs5l);
> + writel(ACFG_CS5A_VAL, &weim->cs5a);
> +
> + writel(ACFG_EIM_VAL, &weim->eim);
> +}
> +
> +static void board_setup_port(void)
> +{
> + struct system_control_regs *system = \
> + (struct system_control_regs *)IMX_SYSTEM_CTL_BASE;
> +
> + writel(ACFG_FMCR_VAL, &system->fmcr);
> +}
> +
> +static void board_setup_clock()
> +{
> + struct pll_regs *pll = (struct pll_regs *)IMX_PLL_BASE;
> + volatile int wait = 0x1000;
> + u32 cscr;
> +
> + /* disable MPLL/SPLL first */
> + cscr = readl(&pll->cscr);
> + cscr &= ~(CSCR_MPEN|CSCR_SPEN);
> + writel(cscr, &pll->cscr);
> +
> + /* pll clock initialization */
> + writel(ACFG_MPCTL0_VAL, &pll->mpctl0);
> + writel(ACFG_SPCTL0_VAL, &pll->spctl0);
> +
> + cscr = ACFG_CSCR_VAL|CSCR_MPLL_RESTART|CSCR_SPLL_RESTART;
> + writel(cscr, &pll->cscr);
> +
> + /* add some delay here */
> + while (wait)
> + wait--;
> +
> + /* peripheral clock divider */
> + writel(ACFG_PCDR0_VAL, &pll->pcdr0);
> + writel(ACFG_PCDR1_VAL, &pll->pcdr1);
> +
> + /* Configure PCCR0 and PCCR1 */
> + writel(ACFG_PCCR0_VAL, &pll->pccr0);
> + writel(ACFG_PCCR1_VAL, &pll->pccr1);
> +}
> +
> +int board_early_init_f(void)
> +{
> + board_setup_aipi();
> + board_setup_csx();
> + board_setup_port();
> + board_setup_clock();
> +
> + return 0;
> +}
> +
> +int
> +board_init(void)
> +{
> + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
> +
> + apf27_gpio_init();
> + apf27_devices_init();
> +
> + return 0;
> +}
> +
> +int
> +dram_init(void)
> +{
> + /* dram_init must store complete ramsize in gd->ram_size */
> + if (get_num_ram_bank() > 1) {
> + gd->ram_size = PHYS_SDRAM_2 - CONFIG_SYS_SDRAM_BASE
> + + get_ram_size((void *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE);
> + } else {
> + gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1,
> + PHYS_SDRAM_1_SIZE);
> + }
> +
> + return 0;
> +}
> +
> +void dram_init_banksize(void)
> +{
> + phys_size_t ramsize = gd->ram_size;
> +
> + if (get_num_ram_bank() > 1)
> + ramsize -= PHYS_SDRAM_2 - CONFIG_SYS_SDRAM_BASE;
> +
> + gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
> + gd->bd->bi_dram[0].size = ramsize;
> + gd->ram_size = gd->bd->bi_dram[0].size;
> +
> + if (CONFIG_NR_DRAM_BANKS > 1) {
> + gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
> + if (get_num_ram_bank() > 1)
> + gd->bd->bi_dram[1].size = ramsize;
> + else
> + gd->bd->bi_dram[1].size = 0;
> + gd->ram_size += gd->bd->bi_dram[1].size;
> + }
> +}
> +
> +/*
> + * Miscellaneous intialization
> + */
> +int
> +misc_init_r(void)
> +{
> + char *s;
> + u_char * firmware_buffer = (u_char *)(CONFIG_SYS_LOAD_ADDR + \
> + CONFIG_SYS_MONITOR_LEN);
> + size_t size = 0;
> + size_t offset = -1;
> + char *autoload = getenv("firmware_autoload");
Is this used?
> + u8 pnum;
> + struct mtd_device *dev;
> + struct part_info *part;
> +
> + /* detect compatibility issue of environment version */
> + s = getenv("env_version");
> + if ((NULL == s) || (0 != strcmp(s, CONFIG_ENV_VERSION))) {
> + char * const vars[] = {"flash_reset_env"};
> + printf("*** Warning - Environment version change suggests: "
> + "run flash_reset_env; reset\n");
> + set_default_vars(1, vars);
> + }
> +
> + /* Unlock whole flash but U-Boot */
> + s = getenv("env_offset");
> + offset = CONFIG_ENV_OFFSET;
> + if ((s != NULL) && (0 != strcmp(s, "0")))
> + offset = simple_strtoul(s, NULL, 16);
> +
> + if (nand_unlock(&nand_info[0], offset, nand_info[0].size - offset, 0))
> + printf("NAND flash lock/unlocked failed\n");
> +
> +
> + return 0;
> +}
> +
> +int checkboard(void)
> +{
> + printf("Board: Armadeus APF27 revision %d\n", get_board_rev());
> + return 0;
> +}
> +
> +void enable_caches(void)
> +{
> + /* Enable D-cache. I-cache is already enabled in start.S */
> + dcache_enable();
> +}
> +
> +inline void lowlevel_init(void) {}
What's the point of defining lowlevel_init? If you don't do low level
inits, then you can define CONFIG_SKIP_LOWLEVEL_INIT in the board
config header file.
> diff --git a/board/armadeus/apf27/apf27.h b/board/armadeus/apf27/apf27.h
> new file mode 100644
> index 0000000..bb007e8
> --- /dev/null
> +++ b/board/armadeus/apf27/apf27.h
> @@ -0,0 +1,477 @@
> +#ifndef __APF27_H
> +#define __APF27_H
> +
> +/* FPGA program pin configuration */
> +#define ACFG_FPGA_PWR (GPIO_PORTF | 19) /* FPGA prog pin */
> +#define ACFG_FPGA_PRG (GPIO_PORTF | 11) /* FPGA prog pin */
> +#define ACFG_FPGA_CLK (GPIO_PORTF | 15) /* FPGA clk pin */
> +#define ACFG_FPGA_RDATA 0xD6000000 /* FPGA data addr */
> +#define ACFG_FPGA_WDATA 0xD6000000 /* FPGA data addr */
> +#define ACFG_FPGA_INIT (GPIO_PORTF | 12) /* FPGA init pin */
> +#define ACFG_FPGA_DONE (GPIO_PORTF | 9) /* FPGA done pin */
> +#define ACFG_FPGA_RW (GPIO_PORTF | 21) /* FPGA done pin */
> +#define ACFG_FPGA_CS (GPIO_PORTF | 22) /* FPGA done pin */
> +#define ACFG_FPGA_SUSPEND (GPIO_PORTF | 10) /* FPGA done pin */
> +#define ACFG_FPGA_RESET (GPIO_PORTF | 7) /* FPGA done pin */
> +
> +/* MPU CLOCK source before PLL */
> +/* ACFG_CLK_FREQ (2/3 MPLL clock or ext 266 MHZ) */
> +#ifndef CONFIG_MX27_CLK26
> +#if (CONFIG_MX27_CLK32 == 32000)
> +#define ACFG_MPCTL0_VAL 0x00211803 /* 398.998 MHz */
> +#define ACFG_MPCTL1_VAL 0
> +#define CONFIG_MPLL_FREQ 399
> +#else /* CONFIG_MX27_CLK32 == 32768*/
> +#define ACFG_MPCTL0_VAL 0x01EF15D5 /* 399.000 MHz */
> +#define ACFG_MPCTL1_VAL 0
> +#define CONFIG_MPLL_FREQ 399
> +#endif /* CONFIG_MX27_CLK32 */
> +#else /* CONFIG_MX27_CLK26 in use*/
> +#define ACFG_MPCTL0_VAL 0x00331C23 /* 399.000 MHz */
> +#define ACFG_MPCTL1_VAL 0
> +#define CONFIG_MPLL_FREQ 399
> +#endif /* CONFIG_MX27_CLK26 */
> +
> +#define ACFG_CLK_FREQ (CONFIG_MPLL_FREQ*2/3) /* 266 MHz */
> +
> +/* Serial clock source before PLL (should be named ACFG_SYSPLL_CLK_FREQ)*/
> +#ifndef CONFIG_MX27_CLK26
> +#if (CONFIG_MX27_CLK32 == 32000)
> +#define ACFG_SPCTL0_VAL 0x04A02419 /* 300.00020 MHz */
> +#define ACFG_SPCTL1_VAL 0
> +#define CONFIG_SPLL_FREQ 300 /* MHz */
> +#else /* CONFIG_MX27_CLK32 == 32768*/
> +#define ACFG_SPCTL0_VAL 0x0475206F /* 299.99937 MHz */
> +#define ACFG_SPCTL1_VAL 0
> +#define CONFIG_SPLL_FREQ 300 /* MHz */
> +#endif /* CONFIG_MX27_CLK32 */
> +#else /* CONFIG_MX27_CLK26 in use*/
> +#define ACFG_SPCTL0_VAL 0x040C2C07 /* 300 MHz */
> +#define ACFG_SPCTL1_VAL 0x0
> +#define CONFIG_SPLL_FREQ 300 /* MHz */
> +#endif /* CONFIG_MX27_CLK26 */
> +
> +/* ARM bus frequency (have to be a CONFIG_MPLL_FREQ ratio) */
> +#define CONFIG_ARM_FREQ 399 /* up to 400 MHz */
> +
> +/* external bus frequency (have to be a ACFG_CLK_FREQ ratio) */
> +#define CONFIG_HCLK_FREQ 133 /* (ACFG_CLK_FREQ/2) */
> +
> +#define CONFIG_PERIF1_FREQ 16 /* 16.625 MHz UART, GPT, PWM*/
> +#define CONFIG_PERIF2_FREQ 33 /* 33.25 MHz CSPI and SDHC */
> +#define CONFIG_PERIF3_FREQ 33 /* 33.25 MHz LCD*/
> +#define CONFIG_PERIF4_FREQ 33 /* 33.25 MHz CSI*/
> +#define CONFIG_SSI1_FREQ 66 /* 66.50 MHz SSI1*/
> +#define CONFIG_SSI2_FREQ 66 /* 66.50 MHz SSI2*/
> +#define CONFIG_MSHC_FREQ 66 /* 66.50 MHz MSHC*/
> +#define CONFIG_H264_FREQ 66 /* 66.50 MHz H264*/
> +#define CONFIG_CLK0_DIV 3 /* Divide CLK0 by 4 */
> +#define CONFIG_CLK0_EN 1 /* CLK0 enabled */
> +
> +/* external bus frequency (have to be a CONFIG_HCLK_FREQ ratio) */
> +#define CONFIG_NFC_FREQ 44 /* NFC Clock up to 44 MHz wh 133MHz*/
> +
> +/* external serial bus frequency (have to be a CONFIG_SPLL_FREQ ratio) */
> +#define CONFIG_USB_FREQ 60 /* 60 MHz */
> +
> +/*
> + * SDRAM
> + */
> +#if (ACFG_SDRAM_MBYTE_SYZE == 64) /* micron MT46H16M32LF -6 */
> +/* micron 64MB */
> +#define ACFG_SDRAM_NUM_COL 9 /* 8, 9, 10 or 11
> + column address bits */
> +#define ACFG_SDRAM_NUM_ROW 13 /* 11, 12 or 13
> + row address bits */
> +#define ACFG_SDRAM_REFRESH 3 /* 0=OFF 1=2048
> + 2=4096 3=8192 refresh */
> +#define ACFG_SDRAM_EXIT_PWD 25 /* ns exit power
> + down delay */
> +#define ACFG_SDRAM_W2R_DELAY 1 /* write to read
> + cycle delay > 0 */
> +#define ACFG_SDRAM_ROW_PRECHARGE_DELAY 18 /* ns */
> +#define ACFG_SDRAM_TMRD_DELAY 2 /* Load mode register
> + cycle delay 1..4 */
> +#define ACFG_SDRAM_TWR_DELAY 1 /* LPDDR: 0=2ck 1=3ck;
> + SDRAM: 0=1ck 1=2ck*/
> +#define ACFG_SDRAM_RAS_DELAY 42 /* ns ACTIVE-to-PRECHARGE
> + delay */
> +#define ACFG_SDRAM_RRD_DELAY 12 /* ns ACTIVE-to-ACTIVE
> + delay */
> +#define ACFG_SDRAM_RCD_DELAY 18 /* ns Row to Column delay */
> +#define ACFG_SDRAM_RC_DELAY 70 /* ns Row cycle delay (tRFC
> + refresh to command) */
> +#define ACFG_SDRAM_CLOCK_CYCLE_CL_1 0 /* ns clock cycle time
> + estimated fo CL=1
> + 0=force 3 for lpddr */
> +#define ACFG_SDRAM_PARTIAL_ARRAY_SR 0 /* 0=full 1=half 2=quater
> + 3=Eighth 4=Sixteenth */
> +#define ACFG_SDRAM_DRIVE_STRENGH 0 /* 0=Full-strength 1=half
> + 2=quater 3=Eighth */
> +#define ACFG_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
> +#define ACFG_SDRAM_SINGLE_ACCESS 0 /* 1= single access;
> + 0 = Burst mode */
> +#endif
> +
> +#if (ACFG_SDRAM_MBYTE_SYZE == 128)
> +/* micron 128MB */
> +#define ACFG_SDRAM_NUM_COL 9 /* 8, 9, 10 or 11
> + column address bits */
> +#define ACFG_SDRAM_NUM_ROW 14 /* 11, 12 or 13
> + row address bits */
> +#define ACFG_SDRAM_REFRESH 3 /* 0=OFF 1=2048
> + 2=4096 3=8192 refresh */
> +#define ACFG_SDRAM_EXIT_PWD 25 /* ns exit power
> + down delay */
> +#define ACFG_SDRAM_W2R_DELAY 1 /* write to read
> + cycle delay > 0 */
> +#define ACFG_SDRAM_ROW_PRECHARGE_DELAY 18 /* ns */
> +#define ACFG_SDRAM_TMRD_DELAY 2 /* Load mode register
> + cycle delay 1..4 */
> +#define ACFG_SDRAM_TWR_DELAY 1 /* LPDDR: 0=2ck 1=3ck;
> + SDRAM: 0=1ck 1=2ck*/
> +#define ACFG_SDRAM_RAS_DELAY 42 /* ns ACTIVE-to-PRECHARGE
> + delay */
> +#define ACFG_SDRAM_RRD_DELAY 12 /* ns ACTIVE-to-ACTIVE
> + delay */
> +#define ACFG_SDRAM_RCD_DELAY 18 /* ns Row to Column delay */
> +#define ACFG_SDRAM_RC_DELAY 70 /* ns Row cycle delay (tRFC
> + refresh to command)*/
> +#define ACFG_SDRAM_CLOCK_CYCLE_CL_1 0 /* ns clock cycle time
> + estimated fo CL=1
> + 0=force 3 for lpddr*/
> +#define ACFG_SDRAM_PARTIAL_ARRAY_SR 0 /* 0=full 1=half 2=quater
> + 3=Eighth 4=Sixteenth */
> +#define ACFG_SDRAM_DRIVE_STRENGH 0 /* 0=Full-strength 1=half
> + 2=quater 3=Eighth */
> +#define ACFG_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
> +#define ACFG_SDRAM_SINGLE_ACCESS 0 /* 1= single access;
> + 0 = Burst mode */
> +#endif
> +
> +#if (ACFG_SDRAM_MBYTE_SYZE == 256)
> +/* micron 256MB */
> +#define ACFG_SDRAM_NUM_COL 10 /* 8, 9, 10 or 11
> + column address bits */
> +#define ACFG_SDRAM_NUM_ROW 14 /* 11, 12 or 13
> + row address bits */
> +#define ACFG_SDRAM_REFRESH 3 /* 0=OFF 1=2048
> + 2=4096 3=8192 refresh */
> +#define ACFG_SDRAM_EXIT_PWD 25 /* ns exit power
> + down delay */
> +#define ACFG_SDRAM_W2R_DELAY 1 /* write to read cycle
> + delay > 0 */
> +#define ACFG_SDRAM_ROW_PRECHARGE_DELAY 18 /* ns */
> +#define ACFG_SDRAM_TMRD_DELAY 2 /* Load mode register
> + cycle delay 1..4 */
> +#define ACFG_SDRAM_TWR_DELAY 1 /* LPDDR: 0=2ck 1=3ck;
> + SDRAM: 0=1ck 1=2ck */
> +#define ACFG_SDRAM_RAS_DELAY 42 /* ns ACTIVE-to-PRECHARGE
> + delay */
> +#define ACFG_SDRAM_RRD_DELAY 12 /* ns ACTIVE-to-ACTIVE
> + delay */
> +#define ACFG_SDRAM_RCD_DELAY 18 /* ns Row to Column delay */
> +#define ACFG_SDRAM_RC_DELAY 70 /* ns Row cycle delay (tRFC
> + refresh to command) */
> +#define ACFG_SDRAM_CLOCK_CYCLE_CL_1 0 /* ns clock cycle time
> + estimated fo CL=1
> + 0=force 3 for lpddr */
> +#define ACFG_SDRAM_PARTIAL_ARRAY_SR 0 /* 0=full 1=half 2=quater
> + 3=Eighth 4=Sixteenth */
> +#define ACFG_SDRAM_DRIVE_STRENGH 0 /* 0=Full-strength
> + 1=half
> + 2=quater
> + 3=Eighth */
> +#define ACFG_SDRAM_BURST_LENGTH 3 /* 2^N BYTES (N=0..3) */
> +#define ACFG_SDRAM_SINGLE_ACCESS 0 /* 1= single access;
> + 0 = Burst mode */
> +#endif
> +
> +/*
> + * External interface
> + */
> +/*
> + * CSCRxU_VAL:
> + * 31| x | x | x x |x x x x| x x | x | x |x x x x|16
> + * |SP |WP | BCD | BCS | PSZ |PME|SYNC| DOL |
> + *
> + * 15| x x | x x x x x x | x | x x x x | x x x x |0
> + * | CNC | WSC |EW | WWS | EDC |
> + *
> + * CSCRxL_VAL:
> + * 31| x x x x | x x x x | x x x x | x x x x |16
> + * | OEA | OEN | EBWA | EBWN |
> + * 15|x x x x| x |x x x |x x x x| x | x | x | x | 0
> + * | CSA |EBC| DSZ | CSN |PSR|CRE|WRAP|CSEN|
> + *
> + * CSCRxA_VAL:
> + * 31| x x x x | x x x x | x x x x | x x x x |16
> + * | EBRA | EBRN | RWA | RWN |
> + * 15| x | x x |x x x|x x|x x|x x| x | x | x | x | 0
> + * |MUM| LAH | LBN |LBA|DWW|DCT|WWU|AGE|CNC2|FCE|
> + */
> +
> +/* CS0 configuration for 16 bit nor flash */
> +#define ACFG_CS0U_VAL 0x0000CC03
> +#define ACFG_CS0L_VAL 0xa0330D01
> +#define ACFG_CS0A_VAL 0x00220800
> +
> +#define ACFG_CS1U_VAL 0x00000f00
> +#define ACFG_CS1L_VAL 0x00000D01
> +#define ACFG_CS1A_VAL 0
> +
> +#define ACFG_CS2U_VAL 0
> +#define ACFG_CS2L_VAL 0
> +#define ACFG_CS2A_VAL 0
> +
> +#define ACFG_CS3U_VAL 0
> +#define ACFG_CS3L_VAL 0
> +#define ACFG_CS3A_VAL 0
> +
> +#define ACFG_CS4U_VAL 0
> +#define ACFG_CS4L_VAL 0
> +#define ACFG_CS4A_VAL 0
> +
> +/* FPGA 16 bit data bus */
> +#define ACFG_CS5U_VAL 0x00000600
> +#define ACFG_CS5L_VAL 0x00000D01
> +#define ACFG_CS5A_VAL 0
> +
> +#define ACFG_EIM_VAL 0x00002200
> +
> +/* FPGA specific settings */
> +/* CLKO */
> +#define ACFG_CCSR_VAL 0x00000305
> +/* drive strength CLKO set to 2*/
> +#define ACFG_DSCR10_VAL 0x00020000
> +/* drive strength A1..A12 set to 2*/
> +#define ACFG_DSCR3_VAL 0x02AAAAA8
> +/* drive strength ctrl*/
> +#define ACFG_DSCR7_VAL 0x00020880
> +/* drive strength data*/
> +#define ACFG_DSCR2_VAL 0xAAAAAAAA
> +
> +
> +/*
> + * Default configuration for GPIOs and peripherals
> + */
> +#ifndef ACFG_APF27_CUSTOM
> +#define ACFG_DDIR_A_VAL 0x00000000
> +#define ACFG_OCR1_A_VAL 0x00000000
> +#define ACFG_OCR2_A_VAL 0x00000000
> +#define ACFG_ICFA1_A_VAL 0xFFFFFFFF
> +#define ACFG_ICFA2_A_VAL 0xFFFFFFFF
> +#define ACFG_ICFB1_A_VAL 0xFFFFFFFF
> +#define ACFG_ICFB2_A_VAL 0xFFFFFFFF
> +#define ACFG_DR_A_VAL 0x00000000
> +#define ACFG_GIUS_A_VAL 0xFFFFFFFF
> +#define ACFG_ICR1_A_VAL 0x00000000
> +#define ACFG_ICR2_A_VAL 0x00000000
> +#define ACFG_IMR_A_VAL 0x00000000
> +#define ACFG_GPR_A_VAL 0x00000000
> +#define ACFG_PUEN_A_VAL 0xFFFFFFFF
> +
> +#define ACFG_DDIR_B_VAL 0x00000000
> +#define ACFG_OCR1_B_VAL 0x00000000
> +#define ACFG_OCR2_B_VAL 0x00000000
> +#define ACFG_ICFA1_B_VAL 0xFFFFFFFF
> +#define ACFG_ICFA2_B_VAL 0xFFFFFFFF
> +#define ACFG_ICFB1_B_VAL 0xFFFFFFFF
> +#define ACFG_ICFB2_B_VAL 0xFFFFFFFF
> +#define ACFG_DR_B_VAL 0x00000000
> +#define ACFG_GIUS_B_VAL 0xFF3FFFF0
> +#define ACFG_ICR1_B_VAL 0x00000000
> +#define ACFG_ICR2_B_VAL 0x00000000
> +#define ACFG_IMR_B_VAL 0x00000000
> +#define ACFG_GPR_B_VAL 0x00000000
> +#define ACFG_PUEN_B_VAL 0xFFFFFFFF
> +
> +#define ACFG_DDIR_C_VAL 0x00000000
> +#define ACFG_OCR1_C_VAL 0x00000000
> +#define ACFG_OCR2_C_VAL 0x00000000
> +#define ACFG_ICFA1_C_VAL 0xFFFFFFFF
> +#define ACFG_ICFA2_C_VAL 0xFFFFFFFF
> +#define ACFG_ICFB1_C_VAL 0xFFFFFFFF
> +#define ACFG_ICFB2_C_VAL 0xFFFFFFFF
> +#define ACFG_DR_C_VAL 0x00000000
> +#define ACFG_GIUS_C_VAL 0xFFFFC07F
> +#define ACFG_ICR1_C_VAL 0x00000000
> +#define ACFG_ICR2_C_VAL 0x00000000
> +#define ACFG_IMR_C_VAL 0x00000000
> +#define ACFG_GPR_C_VAL 0x00000000
> +#define ACFG_PUEN_C_VAL 0xFFFFFF87
> +
> +#define ACFG_DDIR_D_VAL 0x00000000
> +#define ACFG_OCR1_D_VAL 0x00000000
> +#define ACFG_OCR2_D_VAL 0x00000000
> +#define ACFG_ICFA1_D_VAL 0xFFFFFFFF
> +#define ACFG_ICFA2_D_VAL 0xFFFFFFFF
> +#define ACFG_ICFB1_D_VAL 0xFFFFFFFF
> +#define ACFG_ICFB2_D_VAL 0xFFFFFFFF
> +#define ACFG_DR_D_VAL 0x00000000
> +#define ACFG_GIUS_D_VAL 0xFFFFFFFF
> +#define ACFG_ICR1_D_VAL 0x00000000
> +#define ACFG_ICR2_D_VAL 0x00000000
> +#define ACFG_IMR_D_VAL 0x00000000
> +#define ACFG_GPR_D_VAL 0x00000000
> +#define ACFG_PUEN_D_VAL 0xFFFFFFFF
> +
> +#define ACFG_DDIR_E_VAL 0x00000000
> +#define ACFG_OCR1_E_VAL 0x00000000
> +#define ACFG_OCR2_E_VAL 0x00000000
> +#define ACFG_ICFA1_E_VAL 0xFFFFFFFF
> +#define ACFG_ICFA2_E_VAL 0xFFFFFFFF
> +#define ACFG_ICFB1_E_VAL 0xFFFFFFFF
> +#define ACFG_ICFB2_E_VAL 0xFFFFFFFF
> +#define ACFG_DR_E_VAL 0x00000000
> +#define ACFG_GIUS_E_VAL 0xFCFFCCF8
> +#define ACFG_ICR1_E_VAL 0x00000000
> +#define ACFG_ICR2_E_VAL 0x00000000
> +#define ACFG_IMR_E_VAL 0x00000000
> +#define ACFG_GPR_E_VAL 0x00000000
> +#define ACFG_PUEN_E_VAL 0xFFFFFFFF
> +
> +#define ACFG_DDIR_F_VAL 0x00000000
> +#define ACFG_OCR1_F_VAL 0x00000000
> +#define ACFG_OCR2_F_VAL 0x00000000
> +#define ACFG_ICFA1_F_VAL 0xFFFFFFFF
> +#define ACFG_ICFA2_F_VAL 0xFFFFFFFF
> +#define ACFG_ICFB1_F_VAL 0xFFFFFFFF
> +#define ACFG_ICFB2_F_VAL 0xFFFFFFFF
> +#define ACFG_DR_F_VAL 0x00000000
> +#define ACFG_GIUS_F_VAL 0xFF7F8000
> +#define ACFG_ICR1_F_VAL 0x00000000
> +#define ACFG_ICR2_F_VAL 0x00000000
> +#define ACFG_IMR_F_VAL 0x00000000
> +#define ACFG_GPR_F_VAL 0x00000000
> +#define ACFG_PUEN_F_VAL 0xFFFFFFFF
> +#endif /* ACFG_APF27_CUSTOM */
> +
> +/* Enforce DDR signal strengh & enable USB/PP/DMA burst override bits */
> +#define ACFG_GPCR_VAL 0x0003000F
> +
> +#define ACFG_ESDMISC_VAL ESDMISC_LHD+ESDMISC_MDDREN
> +
> +/* FMCR select num LPDDR RAMs and nand 16bits, 2KB pages */
> +#if (CONFIG_NR_DRAM_BANKS == 1)
> +#define ACFG_FMCR_VAL 0xFFFFFFF9
> +#elif (CONFIG_NR_DRAM_BANKS == 2)
> +#define ACFG_FMCR_VAL 0xFFFFFFFB
> +#endif
> +
> +#ifndef ACFG_APF27_CUSTOM
> +#define ACFG_AIPI1_PSR0_VAL 0x20040304
> +#define ACFG_AIPI1_PSR1_VAL 0xDFFBFCFB
> +#define ACFG_AIPI2_PSR0_VAL 0x00000000
> +#define ACFG_AIPI2_PSR1_VAL 0xFFFFFFFF
> +#endif /* ACFG_APF27_CUSTOM */
> +
> +/* PCCR enable DMA FEC I2C1 IIM SDHC1 */
> +#ifndef ACFG_APF27_CUSTOM
> +#define ACFG_PCCR0_VAL 0x05070410
> +#define ACFG_PCCR1_VAL 0xA14A0608
> +#endif /* ACFG_APF27_CUSTOM */
> +
> +/*
> + * From here, there should not be any user configuration.
> + * All Equations are automatic
> + */
> +
> +/* fixme none integer value (7.5ns) => 2*hclock = 15ns */
> +#define ACFG_2XHCLK_LGTH (2000/CONFIG_HCLK_FREQ) /* ns */
> +
> +/* USB 60 MHz ; ARM up to 400; HClK up to 133MHz*/
> +#ifdef CONFIG_MX27_CLK26
> +#define CSCR_MASK 0x0303800D
> +#else
> +#define CSCR_MASK 0x0300800D
> +#endif
> +#define ACFG_CSCR_VAL\
> + (CSCR_MASK \
> + |((((CONFIG_SPLL_FREQ/CONFIG_USB_FREQ)-1)&0x07) << 28) \
> + |((((CONFIG_MPLL_FREQ/CONFIG_ARM_FREQ)-1)&0x03) << 12) \
> + |((((ACFG_CLK_FREQ/CONFIG_HCLK_FREQ)-1)&0x03) << 8))
> +
> +/* SSIx CLKO NFC H264 MSHC */
> +#define ACFG_PCDR0_VAL\
> + (((((ACFG_CLK_FREQ/CONFIG_MSHC_FREQ)-1)&0x3F)<<0) \
> + |((((CONFIG_HCLK_FREQ/CONFIG_NFC_FREQ)-1)&0x0F)<<6) \
> + |(((((ACFG_CLK_FREQ/CONFIG_H264_FREQ)-2)*2)&0x3F)<<10)\
> + |(((((ACFG_CLK_FREQ/CONFIG_SSI1_FREQ)-2)*2)&0x3F)<<16)\
> + |(((CONFIG_CLK0_DIV)&0x07)<<22)\
> + |(((CONFIG_CLK0_EN)&0x01)<<25)\
> + |(((((ACFG_CLK_FREQ/CONFIG_SSI2_FREQ)-2)*2)&0x3F)<<26))
> +
> +/* PERCLKx */
> +#define ACFG_PCDR1_VAL\
> + (((((ACFG_CLK_FREQ/CONFIG_PERIF1_FREQ)-1)&0x3F)<<0) \
> + |((((ACFG_CLK_FREQ/CONFIG_PERIF2_FREQ)-1)&0x3F)<<8) \
> + |((((ACFG_CLK_FREQ/CONFIG_PERIF3_FREQ)-1)&0x3F)<<16) \
> + |((((ACFG_CLK_FREQ/CONFIG_PERIF4_FREQ)-1)&0x3F)<<24))
> +
> +/* SDRAM controller programming Values */
> +#if (((2*ACFG_SDRAM_CLOCK_CYCLE_CL_1) > (3*ACFG_2XHCLK_LGTH)) \
> + || (ACFG_SDRAM_CLOCK_CYCLE_CL_1 < 1))
> +#define REG_FIELD_SCL_VAL 3
> +#define REG_FIELD_SCLIMX_VAL 0
> +#else
> +#define REG_FIELD_SCL_VAL\
> + ((2*ACFG_SDRAM_CLOCK_CYCLE_CL_1+ACFG_2XHCLK_LGTH-1)/ \
> + ACFG_2XHCLK_LGTH)
> +#define REG_FIELD_SCLIMX_VAL REG_FIELD_SCL_VAL
> +#endif
> +
> +#if ((2*ACFG_SDRAM_RC_DELAY) > (16*ACFG_2XHCLK_LGTH))
> +#define REG_FIELD_SRC_VAL 0
> +#else
> +#define REG_FIELD_SRC_VAL\
> + ((2*ACFG_SDRAM_RC_DELAY+ACFG_2XHCLK_LGTH-1)/ \
> + ACFG_2XHCLK_LGTH)
> +#endif
> +
> +/* TBD Power down timer ; PRCT Bit Field Encoding; burst length 8 ; FP = 0*/
> +#define REG_ESDCTL_BASE_CONFIG (0x80020485\
> + | (((ACFG_SDRAM_NUM_ROW-11)&0x7)<<24)\
> + | (((ACFG_SDRAM_NUM_COL-8)&0x3)<<20)\
> + | (((ACFG_SDRAM_REFRESH)&0x7)<<13))
> +
> +#define ACFG_NORMAL_RW_CMD ((0x0<<28)+REG_ESDCTL_BASE_CONFIG)
> +#define ACFG_PRECHARGE_CMD ((0x1<<28)+REG_ESDCTL_BASE_CONFIG)
> +#define ACFG_AUTOREFRESH_CMD ((0x2<<28)+REG_ESDCTL_BASE_CONFIG)
> +#define ACFG_SET_MODE_REG_CMD ((0x3<<28)+REG_ESDCTL_BASE_CONFIG)
> +
> +/* ESDRAMC Configuration Registers : force CL=3 to lpddr */
> +#define ACFG_SDRAM_ESDCFG_REGISTER_VAL (0x0\
> + | (((((2*ACFG_SDRAM_EXIT_PWD+ACFG_2XHCLK_LGTH-1)/ \
> + ACFG_2XHCLK_LGTH)-1)&0x3)<<21)\
> + | (((ACFG_SDRAM_W2R_DELAY-1)&0x1)<<20)\
> + | (((((2*ACFG_SDRAM_ROW_PRECHARGE_DELAY+ \
> + ACFG_2XHCLK_LGTH-1)/ACFG_2XHCLK_LGTH)-1)&0x3)<<18) \
> + | (((ACFG_SDRAM_TMRD_DELAY-1)&0x3)<<16)\
> + | (((ACFG_SDRAM_TWR_DELAY)&0x1)<<15)\
> + | (((((2*ACFG_SDRAM_RAS_DELAY+ACFG_2XHCLK_LGTH-1)/ \
> + ACFG_2XHCLK_LGTH)-1)&0x7)<<12) \
> + | (((((2*ACFG_SDRAM_RRD_DELAY+ACFG_2XHCLK_LGTH-1)/ \
> + ACFG_2XHCLK_LGTH)-1)&0x3)<<10) \
> + | (((REG_FIELD_SCLIMX_VAL)&0x3)<<8)\
> + | (((((2*ACFG_SDRAM_RCD_DELAY+ACFG_2XHCLK_LGTH-1)/ \
> + ACFG_2XHCLK_LGTH)-1)&0x7)<<4) \
> + | (((REG_FIELD_SRC_VAL)&0x0F)<<0))
> +
> +/* Issue Mode register Command to SDRAM*/
> +#define ACFG_SDRAM_MODE_REGISTER_VAL\
> + ((((ACFG_SDRAM_BURST_LENGTH)&0x7)<<(0))\
> + | (((REG_FIELD_SCL_VAL)&0x7)<<(4))\
> + | ((0)<<(3)) /* sequentiql access */ \
> + /*| (((ACFG_SDRAM_SINGLE_ACCESS)&0x1)<<(1))*/)
> +
> +/* Issue Extended Mode register Command to SDRAM*/
> +#define ACFG_SDRAM_EXT_MODE_REGISTER_VAL\
> + ((ACFG_SDRAM_PARTIAL_ARRAY_SR<<0)\
> + | (ACFG_SDRAM_DRIVE_STRENGH<<(5))\
> + | (1<<(ACFG_SDRAM_NUM_COL+ACFG_SDRAM_NUM_ROW+1+2)))
> +
> +/* Issue Precharge all Command to SDRAM*/
> +#define ACFG_SDRAM_PRECHARGE_ALL_VAL (1<<10)
> +
> +#endif /* __APF27_H */
> diff --git a/boards.cfg b/boards.cfg
> index 4c63789..72c49df 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -184,6 +184,7 @@ jadecpu arm arm926ejs jadecpu syteco
> mx25pdk arm arm926ejs mx25pdk freescale mx25 mx25pdk:IMX_CONFIG=board/freescale/mx25pdk/imximage.cfg
> tx25 arm arm926ejs tx25 karo mx25
> zmx25 arm arm926ejs zmx25 syteco mx25
> +apf27 arm arm926ejs apf27 armadeus mx27
> imx27lite arm arm926ejs imx27lite logicpd mx27
> magnesium arm arm926ejs imx27lite logicpd mx27
> apx4devkit arm arm926ejs apx4devkit bluegiga mxs apx4devkit
> diff --git a/include/configs/apf27.h b/include/configs/apf27.h
> new file mode 100644
> index 0000000..005f10e
> --- /dev/null
> +++ b/include/configs/apf27.h
> @@ -0,0 +1,458 @@
> +/*
> + *
> + * Configuration settings for the Armadeus Project motherboard APF27
> + *
> + * Copyright (C) 2008-2012 ej / Armadeus Project <eric.jarrige@armadeus.org>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define CONFIG_VERSION_VARIABLE
> +#define CONFIG_ENV_VERSION "3.3"
> +#define CONFIG_IDENT_STRING " apf27 patch 3.8"
> +#define CONFIG_BOARD_NAME apf27
> +
> +/*
> + * SoC configurations
> + */
> +#define CONFIG_ARM926EJS /* this is an ARM926EJS CPU */
> +#define CONFIG_MX27 /* in a Freescale i.MX27 Chip */
> +#define CONFIG_MACH_TYPE 1698 /* APF27 */
> +
> +/*
> + * Enable the call to miscellaneous platform dependent initialization.
> + */
> +#define CONFIG_SYS_NO_FLASH /* to be define before <config_cmd_default.h> */
> +#define CONFIG_MISC_INIT_R
> +#define CONFIG_BOARD_EARLY_INIT_F
> +
> +/*
> + * Board display option
> + */
> +#define CONFIG_DISPLAY_BOARDINFO
> +#define CONFIG_DISPLAY_CPUINFO
> +
> +/*
> + * SPL
> + */
> +/* Copy SPL+U-Boot here */
> +#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_TEXT_BASE - 0x800)
> +/* Size is the partion size */
> +#define CONFIG_SYS_NAND_U_BOOT_SIZE CONFIG_SYS_MONITOR_LEN
> +/* Build image with spl and u-boot */
> +#define CONFIG_NAND_U_BOOT
> +#define CONFIG_SPL_PAD_TO 0xa1000000
> +
> +/*
> + * SPL
> + */
> +#define CONFIG_SPL
> +#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
> +#define CONFIG_SPL_START_S_PATH "board/armadeus/apf27"
> +#define CONFIG_SPL_LDSCRIPT "board/armadeus/apf27/u-boot-spl.lds"
> +#define CONFIG_SPL_LIBCOMMON_SUPPORT
> +#define CONFIG_SPL_LIBGENERIC_SUPPORT
> +
> +
> +/*
> + * BOOTP options
> + */
> +#define CONFIG_BOOTP_SUBNETMASK
> +#define CONFIG_BOOTP_GATEWAY
> +#define CONFIG_BOOTP_HOSTNAME
> +#define CONFIG_BOOTP_BOOTPATH
> +#define CONFIG_BOOTP_BOOTFILESIZE
> +#define CONFIG_BOOTP_DNS
> +#define CONFIG_BOOTP_DNS2
> +
> +#define CONFIG_HOSTNAME CONFIG_BOARD_NAME
> +#define CONFIG_ROOTPATH "/tftpboot/" __stringify(CONFIG_BOARD_NAME) "-root"
> +
> +/*
> + * U-Boot Commands
> + */
> +#include <config_cmd_default.h>
> +
> +#define CONFIG_CMD_ASKENV /* ask for env variable */
> +#define CONFIG_CMD_BSP /* Board Specific functions */
> +#define CONFIG_CMD_CACHE /* icache, dcache */
> +#define CONFIG_CMD_DHCP /* DHCP Support */
> +#define CONFIG_CMD_DNS
> +#define CONFIG_CMD_EXT2
> +#define CONFIG_CMD_FAT /* FAT support */
> +#define CONFIG_CMD_IMX_FUSE /* imx iim fuse */
> +#define CONFIG_CMD_MII /* MII support */
> +#define CONFIG_CMD_MMC
> +#define CONFIG_CMD_MTDPARTS /* MTD partition support */
> +#define CONFIG_CMD_NAND /* NAND support */
> +#define CONFIG_CMD_NAND_LOCK_UNLOCK
> +#define CONFIG_CMD_NAND_TRIMFFS
> +#define CONFIG_CMD_NFS /* NFS support */
> +#define CONFIG_CMD_PING /* ping support */
> +#define CONFIG_CMD_SETEXPR /* setexpr support */
> +#define CONFIG_CMD_UBI
> +#define CONFIG_CMD_UBIFS
> +
> +/*
> + * Memory configurations
> + */
> +#define CONFIG_NR_DRAM_POPULATED 2
> +#define CONFIG_NR_DRAM_BANKS 2
> +
> +#define ACFG_SDRAM_MBYTE_SYZE 64
> +
> +#define PHYS_SDRAM_1 0xA0000000
> +#define PHYS_SDRAM_2 0xB0000000
> +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
> +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (512<<10))
> +#define CONFIG_SYS_MEMTEST_START 0xA0000000 /* memtest test area */
> +#define CONFIG_SYS_MEMTEST_END 0xA0300000 /* 3 MiB RAM test */
> +
> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE \
> + + PHYS_SDRAM_1_SIZE - 0x0100000)
> +
> +#define CONFIG_SYS_TEXT_BASE 0xA1000000
> +
> +/*
> + * FLASH organization
> + */
> +#define ACFG_MONITOR_OFFSET 0x00000000
> +#define CONFIG_SYS_MONITOR_LEN 0x00100000 /* 1MiB */
> +#define CONFIG_ENV_IS_IN_NAND
> +#define CONFIG_ENV_OVERWRITE
> +#define CONFIG_ENV_OFFSET 0x00100000 /* NAND offset */
> +#define CONFIG_ENV_SIZE 0x00020000 /* 128kB */
> +#define CONFIG_ENV_RANGE 0X00080000 /* 512kB */
> +#define CONFIG_ENV_OFFSET_REDUND \
> + (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) /* +512kB */
> +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE /* 512kB */
> +#define CONFIG_FIRMWARE_OFFSET 0x00200000
> +#define CONFIG_KERNEL_OFFSET 0x00300000
> +#define CONFIG_ROOTFS_OFFSET 0x00800000
> +
> +#define CONFIG_MTDMAP "mxc_nand.0"
> +#define MTDIDS_DEFAULT "nand0=" CONFIG_MTDMAP
> +#define MTDPARTS_DEFAULT "mtdparts=" CONFIG_MTDMAP \
> + ":1M(u-boot)ro," \
> + "512K(env)," \
> + "512K(env2)," \
> + "512K(firmware)," \
> + "512K(dtb)," \
> + "5M(kernel)," \
> + "-(rootfs)"
> +
> +/*
> + * U-Boot general configurations
> + */
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_SYS_PROMPT "BIOS> " /* prompt string */
> +#define CONFIG_SYS_CBSIZE 2048 /* console I/O buffer */
> +#define CONFIG_SYS_PBSIZE \
> + (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
> + /* Print buffer size */
> +#define CONFIG_SYS_MAXARGS 16 /* max command args */
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> + /* Boot argument buffer size */
> +#define CONFIG_AUTO_COMPLETE
> +#define CONFIG_CMDLINE_EDITING
> +#define CONFIG_SYS_HUSH_PARSER /* enable the "hush" shell */
> +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* secondary prompt string */
> +
> +/*
> + * Boot Linux
> + */
> +#define CONFIG_CMDLINE_TAG /* send commandline to Kernel */
> +#define CONFIG_SETUP_MEMORY_TAGS /* send memory definition to kernel */
> +#define CONFIG_INITRD_TAG /* send initrd params */
> +
> +#define CONFIG_OF_LIBFDT
> +
> +#define CONFIG_BOOTDELAY 5
> +#define CONFIG_ZERO_BOOTDELAY_CHECK
> +#define CONFIG_BOOTFILE __stringify(CONFIG_BOARD_NAME) "-linux.bin"
> +#define CONFIG_BOOTARGS "console=" __stringify(ACFG_CONSOLE_DEV) "," \
> + __stringify(CONFIG_BAUDRATE) " " MTDPARTS_DEFAULT \
> + " ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs "
> +
> +#define ACFG_CONSOLE_DEV ttySMX0
> +#define CONFIG_BOOTCOMMAND "run ubifsboot"
> +#define CONFIG_SYS_AUTOLOAD "no"
> +/*
> + * Default load address for user programs and kernel
> + */
> +#define CONFIG_LOADADDR 0xA0000000
> +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> +
> +/*
> + * Extra Environments
> + */
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "env_version=" CONFIG_ENV_VERSION "\0" \
> + "consoledev=" __stringify(ACFG_CONSOLE_DEV) "\0" \
> + "mtdparts=" MTDPARTS_DEFAULT "\0" \
> + "partition=nand0,6\0" \
> + "u-boot_addr=" __stringify(ACFG_MONITOR_OFFSET) "\0" \
> + "env_addr=" __stringify(CONFIG_ENV_OFFSET) "\0" \
> + "firmware_addr=" __stringify(CONFIG_FIRMWARE_OFFSET) "\0" \
> + "kernel_addr=" __stringify(CONFIG_KERNEL_OFFSET) "\0" \
> + "rootfs_addr=" __stringify(CONFIG_ROOTFS_OFFSET) "\0" \
> + "board_name=" __stringify(CONFIG_BOARD_NAME) "\0" \
> + "kernel_addr_r=A0000000\0" \
> + "addnfsargs=setenv bootargs ${bootargs} " \
> + "root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \
> + "addubifsargs=setenv bootargs ${bootargs} " \
> + "ubi.mtd=rootfs root=ubi0:rootfs rootfstype=ubifs\0" \
> + "addmmcargs=setenv bootargs ${bootargs} " \
> + "root=/dev/mmcblk0p1 rootfstype=ext2\0" \
> + "addipargs=setenv bootargs ${bootargs} " \
> + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:" \
> + "${hostname}:eth0:off \0" \
> + "nfsboot=setenv bootargs console=${consoledev},${baudrate} " \
> + "${mtdparts} ${extrabootargs}; run addnfsargs addipargs;"\
> + "nfs ${kernel_addr_r} " \
> + "${serverip}:${rootpath}/boot/${board_name}-linux.bin;" \
> + "if test -n ${fdt_addr_r} ; then " \
> + "nand read ${fdt_addr_r} dtb; fi;" \
> + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
> + "ubifsboot=setenv bootargs console=${consoledev},${baudrate} " \
> + "${mtdparts} ${extrabootargs};run addubifsargs addipargs;"\
> + "if test -n ${fdt_addr_r} ; then " \
> + "nand read ${fdt_addr_r} dtb; fi;" \
> + "nboot ${kernel_addr_r} kernel;" \
> + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
> + "mmcboot=setenv bootargs console=${consoledev},${baudrate} " \
> + "${mtdparts} ${extrabootargs}; run addmmcargs addipargs;"\
> + "if test -n ${fdt_addr_r} ; then " \
> + "nand read ${fdt_addr_r} dtb; fi;" \
> + "mmc dev 0; ext2load mmc 0 ${kernel_addr_r}" \
> + " /boot/${board_name}-linux.bin;" \
> + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
> + "boot_nfs_fallback_flash=if ping ${serverip};" \
> + "then echo Boot over NFS; run nfsboot;" \
> + "else echo Boot from the board; run ubifsboot;" \
> + "fi\0" \
> + "firmware_autoload=0\0" \
> + "flash_uboot=nand unlock ${u-boot_addr} ;" \
> + "nand erase.part u-boot;" \
> + "if nand write.trimffs ${fileaddr} ${u-boot_addr} ${filesize};"\
> + "then nand lock; nand unlock ${env_addr};" \
> + "echo Flashing of uboot succeed;" \
> + "else echo Flashing of uboot failed;" \
> + "fi; \0" \
> + "flash_firmware=nand erase.part firmware;" \
> + "if nand write.trimffs ${fileaddr} ${firmware_addr} ${filesize};"\
> + "then echo Flashing of Firmware succeed;" \
> + "else echo Flashing of Firmware failed;" \
> + "fi\0" \
> + "flash_kernel=nand erase.part kernel;" \
> + "if nand write.trimffs ${fileaddr} ${kernel_addr} ${filesize};"\
> + "then echo Flashing of kernel succeed;" \
> + "else echo Flashing of kernel failed;" \
> + "fi\0" \
> + "flash_rootfs=nand erase.part rootfs;" \
> + "if nand write.trimffs ${fileaddr} ${rootfs_addr} ${filesize};"\
> + "then echo Flashing of rootfs succeed;" \
> + "else echo Flashing of rootfs failed;" \
> + "fi\0" \
> + "flash_dtb=nand erase.part dtb;" \
> + "if nand write.trimffs ${fileaddr} dtb ${filesize};" \
> + "then echo Flashing of rootfs succeed;" \
> + "else echo Flashing of rootfs failed;" \
> + "fi\0" \
> + "flash_reset_env=env default -f -a; saveenv;" \
> + "echo Flash environment variables erased!\0" \
> + "download_uboot=tftpboot ${loadaddr} ${board_name}-u-boot-nand.bin\0" \
> + "download_kernel=tftpboot ${loadaddr} ${board_name}-linux.bin\0" \
> + "download_rootfs=tftpboot ${loadaddr} ${board_name}-rootfs.ubi\0" \
> + "download_dtb=tftpboot ${loadaddr} imx27-${board_name}.dtb\0" \
> + "update_uboot=run download_uboot flash_uboot\0" \
> + "update_kernel=run download_kernel flash_kernel\0" \
> + "update_rootfs=run download_rootfs flash_rootfs\0" \
> + "update_dtb=run download_dtb flash_dtb\0" \
> + "update_all=run download_kernel flash_kernel download_rootfs " \
> + "flash_rootfs download_uboot flash_uboot\0" \
> + "unlock_regs=mw 10000008 0; mw 10020008 0\0" \
> +
> +/*
> + * Serial Driver
> + */
> +#define CONFIG_MXC_UART
> +#define CONFIG_CONS_INDEX 1
> +#define CONFIG_BAUDRATE 115200
> +#define CONFIG_MXC_UART_BASE UART1_BASE
> +
> +/*
> + * GPIO
> + */
> +#define CONFIG_MXC_GPIO
> +
> +/*
> + * NOR
> + */
> +
> +/*
> + * NAND
> + */
> +#define CONFIG_NAND_MXC
> +
> +#define CONFIG_MXC_NAND_REGS_BASE 0xD8000000
> +#define CONFIG_SYS_NAND_BASE CONFIG_MXC_NAND_REGS_BASE
> +#define CONFIG_SYS_MAX_NAND_DEVICE 1
> +
> +#define CONFIG_MXC_NAND_HWECC
> +#define CONFIG_SYS_NAND_LARGEPAGE
> +#define IMX27_NAND_16BITS
> +#define NAND_MAX_CHIPS 1
> +
> +
> +#define CONFIG_FLASH_SHOW_PROGRESS 45
> +#define CONFIG_SYS_NAND_QUIET 1
> +
> +#define CONFIG_BOOT_TRACE_REG 0xAFFFFFF8 /* Addr to store traces of SPL boot*/
> +
> +/*
> + * Partitions & Filsystems
> + */
> +#define CONFIG_MTD_DEVICE
> +#define CONFIG_MTD_PARTITIONS
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_SUPPORT_VFAT
> +
> +/*
> + * UBIFS
> + */
> +#define CONFIG_RBTREE
> +#define CONFIG_LZO
> +
> +/*
> + * Ethernet (on SOC imx FEC)
> + */
> +#define CONFIG_FEC_MXC
> +
> +#define CONFIG_NET_MULTI
> +#define CONFIG_FEC_MXC_PHYADDR 0x1f
> +#define CONFIG_MII 1 /* MII PHY management */
> +
> +/*
> + * FPGA
> + */
> +#define CONFIG_FPGA CONFIG_SYS_SPARTAN3
> +#define CONFIG_FPGA_COUNT 1
> +#define CONFIG_FPGA_XILINX
> +#define CONFIG_FPGA_SPARTAN3
> +#define CONFIG_SYS_FPGA_WAIT 20000 /* 20 ms */
> +#define CONFIG_SYS_FPGA_PROG_FEEDBACK
> +#define CONFIG_SYS_FPGA_CHECK_CTRLC
> +#define CONFIG_SYS_FPGA_CHECK_ERROR
> +
> +/*
> + * Fuses - IIM
> + */
> +#ifdef CONFIG_CMD_IMX_FUSE
> +#define IIM_MAC_BANK 0
> +#define IIM_MAC_ROW 5
> +#define IIM0_SCC_KEY 11
> +#define IIM1_SUID 1
> +#endif
> +
> +/*
> + * I2C
> + */
> +
> +#ifdef CONFIG_CMD_I2C
> +#define CONFIG_HARD_I2C 1
> +
> +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
> +#define CONFIG_SYS_I2C_SLAVE 0x7F
> +
> +#define CONFIG_I2C_CMD_TREE
> +#define CONFIG_I2C_MULTI_BUS 2
> +#define CONFIG_SYS_I2C_NOPROBES { }
> +
> +#ifdef CONFIG_CMD_EEPROM
> +# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24LC02 */
> +# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
> +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
> +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* msec */
> +#endif /* CONFIG_CMD_EEPROM */
> +#endif /* CONFIG_CMD_I2C */
> +
> +/*
> + * SPI
> + */
> +
> +/*
> + * SD/MMC
> + */
> +#ifdef CONFIG_CMD_MMC
> +#define CONFIG_MMC
> +#define CONFIG_GENERIC_MMC
> +#define CONFIG_MXC_MMC
> +#define CONFIG_MXC_MCI_REGS_BASE 0x10014000
> +#endif
> +
> +/*
> + * RTC
> + */
> +#ifdef CONFIG_CMD_DATE
> +#define CONFIG_RTC_DS1374
> +#define CONFIG_SYS_RTC_BUS_NUM 0
> +#endif /* CONFIG_CMD_DATE */
> +
> +/*
> + * Watchdog Config
> + */
> +
> +/*
> + * USB
> + */
> +
> +/*
> + * Clocks
> + */
> +#define CONFIG_SYS_HZ 1000 /* Ticks per second */
> +
> +/*
> + * PLL
> + *
> + * 31 | x |x| x x x x |x x x x x x x x x x |x x|x x x x|x x x x x x x x x x| 0
> + * |CPLM|X|----PD---|--------MFD---------|XXX|--MFI--|-----MFN-----------|
> + */
> +#define CONFIG_MX27_CLK32 32768 /* 32768 or 32000 Hz crystal */
> +#undef CONFIG_MX27_CLK26 /* No external 26MHz external clock */
> +
> +#if (ACFG_SDRAM_MBYTE_SYZE == 64) /* micron MT46H16M32LF -6 */
> +/* micron 64MB */
> +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
> +#define PHYS_SDRAM_2_SIZE 0x04000000 /* 64 MB */
> +#endif
> +
> +#if (ACFG_SDRAM_MBYTE_SYZE == 128)
> +/* micron 128MB */
> +#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
> +#define PHYS_SDRAM_2_SIZE 0x08000000 /* 128 MB */
> +#endif
> +
> +#if (ACFG_SDRAM_MBYTE_SYZE == 256)
> +/* micron 256MB */
> +#define PHYS_SDRAM_1_SIZE 0x10000000 /* 256 MB */
> +#define PHYS_SDRAM_2_SIZE 0x10000000 /* 256 MB */
> +#endif
> +
> +#endif /* __CONFIG_H */
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27
2012-10-29 17:35 ` [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27 Philippe Reynes
2012-10-30 20:50 ` Fabio Estevam
@ 2012-11-26 18:02 ` Albert ARIBAUD
2012-12-02 17:09 ` trem
1 sibling, 1 reply; 10+ messages in thread
From: Albert ARIBAUD @ 2012-11-26 18:02 UTC (permalink / raw)
To: u-boot
Hi Philippe,
On Mon, 29 Oct 2012 18:35:56 +0100, Philippe Reynes <tremyfr@yahoo.fr>
wrote:
> Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
> Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
>
> create mode 100644 board/armadeus/apf27/start.S
> create mode 100644 board/armadeus/apf27/u-boot-spl.lds
This is needed by 2/4 to get truly useable support. Please merge both
patches.
Re Fabio's question: the start.S is generic to mx27 -- IIUC, it could
also be applied to e.g. imx27lite or magnesium if these boards'
maintainers felt so inclined. Therefore it could indeed move into
arch/arm/cpu/arm926ejs/mx27.
> diff --git a/board/armadeus/apf27/Makefile b/board/armadeus/apf27/Makefile
> index 1da9548..f57f405 100644
> --- a/board/armadeus/apf27/Makefile
> +++ b/board/armadeus/apf27/Makefile
> @@ -27,11 +27,14 @@ include $(TOPDIR)/config.mk
>
> LIB = $(obj)lib$(BOARD).o
>
> +ifndef CONFIG_SPL_BUILD
> COBJS := apf27.o
> +endif
>
> -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> +SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
> OBJS := $(addprefix $(obj),$(COBJS))
> SOBJS := $(addprefix $(obj),$(SOBJS))
> +START := $(addprefix $(obj),$(START))
>
> $(LIB): $(obj).depend $(OBJS) $(SOBJS)
> $(call cmd_link_o_target, $(OBJS) $(SOBJS))
> diff --git a/board/armadeus/apf27/start.S b/board/armadeus/apf27/start.S
> new file mode 100644
> index 0000000..374b4ea
> --- /dev/null
> +++ b/board/armadeus/apf27/start.S
> @@ -0,0 +1,549 @@
> +/*
> + * IMX27 NAND Flash SPL (Secondary Program Loader)
> + *
> + * Copyright (c) 2008 Armadeus Project / eja
> + *
> + * Based on Freescale NAND SPL
> + *
> + * Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.
> + * Copyright (c) 2008-2012 Eric Jarrige <eric.jarrige@armadeus.org>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +
> +#include <config.h>
> +#include <version.h>
> +#include <asm/macro.h>
> +#include <asm/arch/mxc_nand.h>
> +#include <asm/arch/imx-regs.h>
> +#include <generated/asm-offsets.h>
> +#include "apf27.h"
> +
> +/*
> + * Standard NAND flash commands
> + */
> +#define NAND_CMD_READ0 0
> +#define NAND_CMD_READ1 1
> +#define NAND_CMD_PAGEPROG 0x10
> +#define NAND_CMD_READOOB 0x50
> +#define NAND_CMD_ERASE1 0x60
> +#define NAND_CMD_STATUS 0x70
> +#define NAND_CMD_STATUS_MULTI 0x71
> +#define NAND_CMD_SEQIN 0x80
> +#define NAND_CMD_READID 0x90
> +#define NAND_CMD_ERASE2 0xd0
> +#define NAND_CMD_RESET 0xff
> +
> +/* Extended commands for large page devices */
> +#define NAND_CMD_READSTART 0x30
> +#define NAND_CMD_CACHEDPROG 0x15
> +
> +/* Status bits */
> +#define NAND_STATUS_FAIL 0x01
> +#define NAND_STATUS_FAIL_N1 0x02
> +#define NAND_STATUS_TRUE_READY 0x20
> +#define NAND_STATUS_READY 0x40
> +#define NAND_STATUS_WP 0x80
> +
> + .macro nand_boot
> +
> +#ifdef CONFIG_BOOT_TRACE_REG
> +/*
> + * If CONFIG_BOOT_TRACE_REG is a SDRAM address then be sure to use the following
> + * 2 command after SDRAM init
> + */
> +
> +/* Backup state of previous boot to CONFIG_BOOT_TRACE_REG+4*/
> +#define BACKUP_TRACE() \
> + ldr r4, =CONFIG_BOOT_TRACE_REG; \
> + ldr r3, [r4]; \
> + str r3, [r4, #0x04];
> +
> +/* Save a state of boot at CONFIG_BOOT_TRACE_REG */
> +#define BOOT_TRACE(val) \
> + ldr r4, =CONFIG_BOOT_TRACE_REG; \
> + ldr r3, =val; \
> + str r3, [r4];
> +#else
> +#define BACKUP_TRACE()
> +#define BOOT_TRACE(val)
> +#endif
> +
> +nand_boot_setup:
> +
> + /* Copy SPL image from flash to SDRAM first */
> + BOOT_TRACE(1)
> + ldr r0, =IMX_NFC_MAIN_AREA0
> + add r2, r0, #(IMX_NFC_SPARE_AREA0-IMX_NFC_MAIN_AREA0) //2KB NFC Buff
> + ldr r1, =CONFIG_SYS_NAND_U_BOOT_DST
> +
> + BOOT_TRACE(2)
> +1: ldmia r0!, {r3-r10}
> + stmia r1!, {r3-r10}
> + cmp r0, r2
> + blo 1b
> +
> +
> +
> + /* Jump to SDRAM */
> + BOOT_TRACE(3)
> + ldr r1, =0x7FF
> + and r0, pc, r1 /* offset of pc */
> + ldr r1, =CONFIG_SYS_NAND_U_BOOT_DST
> + add r1, r1, #0x10
> + add pc, r0, r1
> + nop
> + nop
> + nop
> + nop
> +
> +NAND_Copy_Main:
> + BOOT_TRACE(4)
> + /* r0: nfc base. Reloaded after each page copying */
> + ldr r0, =IMX_NFC_MAIN_AREA0
> +
> + /* r1: starting flash addr to be copied. Updated constantly */
> + /* bypass the first preloaded pages */
> + ldr r1, =(IMX_NFC_SPARE_AREA0-IMX_NFC_MAIN_AREA0)
> +
> + /* r2: end of 1st RAM buf. Doesn't change */
> + ldr r2, =IMX_NFC_MAIN_AREA1
> +
> + /* r12: NFC register base. Doesn't change */
> + ldr r12, =IMX_NFC_REGS
> +
> + ldr r11, =CONFIG_SYS_NAND_U_BOOT_DST
> +
> + /* r13: end of SDRAM address for copying. Doesn't change */
> + add r13, r11, #CONFIG_SYS_NAND_U_BOOT_SIZE
> +
> + /* r11: starting SDRAM address for copying. Updated constantly */
> + add r11, r11, r1
> +
> + /* unlock internal buffer */
> + ldr r3, =NFC_CONFIG_UNLOCKED
> + strh r3, [r12, #NFC_OFFSET_CONFIG]
> +
> + /* enable ECC and mask interrupts */
> + ldr r3, =(NFC_CONFIG1_ECC_EN | NFC_CONFIG1_INT_MSK)
> + strh r3, [r12, #NFC_OFFSET_CONFIG1]
> +
> +Nfc_Read_Page:
> + BOOT_TRACE(5)
> + /* send NAND_CMD_READ0 command */
> + ldr r3, =NAND_CMD_READ0;
> + strh r3, [r12, #NFC_OFFSET_FLASH_CMD]
> +
> + ldr r3, =NFC_CONFIG2_FCMD
> + strh r3, [r12, #NFC_OFFSET_CONFIG2]
> + bl do_wait_op_done
> +
> + /* send NAND address to read. TODO small page support */
> + BOOT_TRACE(6)
> + mov r3, r1, lsr #1
> + bl do_addr_input /* 1st addr cycle */
> +
> + mov r3, r1, lsr #9
> + and r3, r3, #0x03
> + bl do_addr_input /* 2nd addr cycle */
> +
> + mov r3, r1, lsr #11
> + bl do_addr_input /* 3rd addr cycle */
> +
> + mov r3, r1, lsr #19
> + bl do_addr_input /* 4th addr cycle */
> +
> + /* Small NAND flashs (== 1Gb) support 5 addr cycles */
> + mov r3, r1, lsr #27
> + bl do_addr_input /* 5th addr cycle */
> +
> + /* send NAND_CMD_READSTART command. TODO small page support */
> + BOOT_TRACE(7)
> + mov r3, #NAND_CMD_READSTART;
> + strh r3, [r12, #NFC_OFFSET_FLASH_CMD]
> + mov r3, #NFC_CONFIG2_FCMD
> + strh r3, [r12, #NFC_OFFSET_CONFIG2]
> + bl do_wait_op_done
> +
> + /* read and copy buf 0 */
> + BOOT_TRACE(8)
> + mov r3, #0
> + strh r3, [r12, #NFC_OFFSET_BUF_ADDR]
> +
> + mov r3, #NFC_CONFIG2_FDO_PAGE
> + strh r3, [r12, #NFC_OFFSET_CONFIG2]
> + bl do_wait_op_done
> +
> + bl Test_And_Copy_Buffer
> +
> + /* read and copy buf 1 */
> + mov r3, #1
> + strh r3, [r12, #NFC_OFFSET_BUF_ADDR]
> +
> + mov r3, #NFC_CONFIG2_FDO_PAGE
> + strh r3, [r12, #NFC_OFFSET_CONFIG2]
> + bl do_wait_op_done
> +
> + bl Test_And_Copy_Buffer
> +
> + /* here we should test if 512B page flash and bypass next buffers */
> + /* read and copy buf 2. TODO small page support */
> + mov r3, #2
> + strh r3, [r12, #NFC_OFFSET_BUF_ADDR]
> +
> + mov r3, #NFC_CONFIG2_FDO_PAGE
> + strh r3, [r12, #NFC_OFFSET_CONFIG2]
> + bl do_wait_op_done
> +
> + bl Test_And_Copy_Buffer
> +
> + /* read and copy buf 3 */
> + mov r3, #3
> + strh r3, [r12, #NFC_OFFSET_BUF_ADDR]
> +
> + mov r3, #NFC_CONFIG2_FDO_PAGE
> + strh r3, [r12, #NFC_OFFSET_CONFIG2]
> + bl do_wait_op_done
> +
> + bl Test_And_Copy_Buffer
> +
> + /* is the last page ? */
> + BOOT_TRACE(12)
> + cmp r11, r13
> + bge NAND_Copy_Main_done
> +
> + /* r0: nfc base. Reloaded after each page copying */
> + ldr r0, =IMX_NFC_MAIN_AREA0
> + /* r2: end of 1st RAM buf. Doesn't change */
> + ldr r2, =IMX_NFC_MAIN_AREA1
> + b Nfc_Read_Page
> +
> +NAND_Copy_Main_done:
> + BOOT_TRACE(13)
> + .endm /* nand_boot */
> +
> + .macro init_aipi
> + /*
> + * setup AIPI1 and AIPI2
> + */
> + write32 AIPI1_PSR0, ACFG_AIPI1_PSR0_VAL
> + write32 AIPI1_PSR1, ACFG_AIPI1_PSR1_VAL
> + write32 AIPI2_PSR0, ACFG_AIPI2_PSR0_VAL
> + write32 AIPI2_PSR1, ACFG_AIPI2_PSR1_VAL
> +
> + /* Change SDRAM signal strengh */
> + ldr r0, =GPCR
> + ldr r1, =ACFG_GPCR_VAL
> + ldr r5, [r0]
> + orr r5, r5, r1
> + str r5, [r0]
> +
> + .endm /* init_aipi */
> +
> + .macro init_clock
> + ldr r0, =CSCR
> + /* disable MPLL/SPLL first */
> + ldr r1, [r0]
> + bic r1, r1, #(CSCR_MPEN|CSCR_SPEN)
> + str r1, [r0]
> +
> + /*
> + * pll clock initialization predefined in apf27.h
> + */
> + write32 MPCTL0, ACFG_MPCTL0_VAL
> + write32 SPCTL0, ACFG_SPCTL0_VAL
> +
> + write32 CSCR, ACFG_CSCR_VAL|CSCR_MPLL_RESTART|CSCR_SPLL_RESTART
> +
> + /*
> + * add some delay here
> + */
> + mov r1, #0x1000
> + 1: subs r1, r1, #0x1
> + bne 1b
> +
> + /* peripheral clock divider */
> + write32 PCDR0, ACFG_PCDR0_VAL
> + write32 PCDR1, ACFG_PCDR1_VAL
> +
> + /* Configure PCCR0 and PCCR1 */
> + write32 PCCR0, ACFG_PCCR0_VAL
> + write32 PCCR1, ACFG_PCCR1_VAL
> +
> + .endm /* init_clock */
> +
> +/*
> + *************************************************************************
> + *
> + * No jump vector table. Use reset vector as direct entry point.
> + * Do not support any interrupt event within SPL
> + *
> + *************************************************************************
> + */
> +
> +
> +.globl _start
> +_start:
> +
> +/*
> + *************************************************************************
> + *
> + * Startup Code (reset vector)
> + *
> + * do important init only if we don't start from memory!
> + * setup Memory and board specific bits prior to relocation.
> + * relocate armboot to ram
> + * setup stack
> + *
> + *************************************************************************
> + */
> +
> +
> +/*
> + * the actual reset code
> + */
> +
> +reset:
> + /*
> + * set the cpu to SVC32 mode
> + */
> + mrs r0,cpsr
> + bic r0,r0,#0x1f
> + orr r0,r0,#0xd3
> + msr cpsr,r0
> +
> + /*
> + * invalidate I/D cache/TLB and drain write buffer
> + */
> + mov r0, #0
> + mcr p15, 0, r0, c7, c7, 0 /* invalidate I cache and D cache */
> + mcr p15, 0, r0, c8, c7, 0 /* invalidate TLBs */
> + mcr p15, 0, r0, c7, c10, 4 /* Drain the write buffer */
> +
> + /*
> + * disable MMU stuff and caches
> + */
> + mrc p15, 0, r0, c1, c0, 0
> + bic r0, r0, #0x00002300 /* clear bits 13, 9:8 (--V- --RS) */
> + bic r0, r0, #0x00000087 /* clear bits 7, 2:0 (B--- -CAM) */
> + orr r0, r0, #0x00000002 /* set bit 2 (A) Align */
> + orr r0, r0, #0x00001000 /* set bit 12 (I) I-Cache */
> + mcr p15, 0, r0, c1, c0, 0
> +
> +init_aipi_start:
> + init_aipi
> +
> + /* check if sdram has been setup (running within sdram) */
> + cmp pc, #0xa0000000 /* start of first sdram memory space */
> + blo init_clock_start
> + cmp pc, #0xc0000000 /* end of second sdram memory space */
> + blo regular_boot
> +
> + /* running from sdram with full code present -> regular_boot */
> +init_clock_start:
> + init_clock
> +
> +init_sdram_start:
> + bl setup_sdram_ddr
> +
> + /* save state of previous boot (SDRAM is configured)*/
> + BACKUP_TRACE()
> +
> + /* nand_boot BOOT_TRACE(1..13) */
> +
> + nand_boot
> +
> + BOOT_TRACE(14) /* start regular U-Boot */
> +
> +regular_boot: /* jump to start of next 2kiB block (U-Boot) */
> + ldr r0, =0xfffff800
> + and r0, r0, pc
> + add pc, r0, #0x800
> +
> +do_wait_op_done:
> + 1:
> + ldrh r3, [r12, #NFC_OFFSET_CONFIG2]
> + ands r3, r3, #NFC_CONFIG2_INT
> + beq 1b
> + mov r3, #0x0
> + strh r3, [r12, #NFC_OFFSET_CONFIG2]
> + mov pc, lr
> +
> +do_addr_input:
> + mov r9, lr
> + and r3, r3, #0xFF
> + strh r3, [r12, #NFC_OFFSET_FLASH_ADDR]
> + mov r3, #NFC_CONFIG2_FADD
> + strh r3, [r12, #NFC_OFFSET_CONFIG2]
> + bl do_wait_op_done
> + mov pc, r9
> +
> +Test_And_Copy_Buffer:
Please avoid mixed case identifiers.
> + /* check for bad block (2 bits error in main or spare are)*/
> + BOOT_TRACE(9)
> + ldrh r4, [r12, #NFC_OFFSET_ECC_STATUS_RESULT]
> + ands r4, r4, #(NFC_ECC_STAT_ERROR2| \
> + (NFC_ECC_STAT_ERROR2<<NFC_ECC_STAT_ERM_SHFT))
> + bne Skip_Bad_Buffer
> +
> + /* check BI byte of the current spare buffer */
> + ldr r4, =IMX_NFC_SPARE_AREA0
> + ldrh r3, [r12, #NFC_OFFSET_BUF_ADDR] /* for the current buffer */
> + orr r4, r3, lsl #0x04
> +
> + /* at bi word offset 4. */
> + /* Fixme position change betwwen 8 and 16 bits bus */
> + ldrh r4, [r4, #0x04]
> + and r4, r4, #0x0FF00 /* has to be 0xFFxx */
> + cmp r4, #0x0FF00
> + bne Skip_Bad_Buffer
> +
> +Copy_Good_Buffer:
> + /* copying 512 bytes buffer */
> + BOOT_TRACE(10)
> +1: ldmia r0!, {r3-r10}
> + stmia r11!, {r3-r10}
> + cmp r0, r2
> + blo 1b
> + b End_Of_Copy
> +
> +Skip_Bad_Buffer:
> + BOOT_TRACE(11)
> + /* bad pages do not contain valid data and have to be skip */
> + add r0, r0, #0x200
> +
> + /* rewind ram addr to start of buffer */
> + ldr r3, =(~0x1FF)
> + and r11, r11, r3
> +
> +End_Of_Copy:
> + add r2, r2, #0x200
> + add r1, r1, #0x200
> +
> + mov pc, lr
> +
> +
> +setup_sdram_ddr:
> +
> + /* wait for SDRAM/LPDDR ready (SDRAMRDY) */
> + ldr r0, =IMX_ESD_BASE
> + ldr r4, =ESDMISC_SDRAM_RDY
> +2: ldr r1, [r0, #ESDMISC_ROF]
> + ands r1, r1, r4
> + bpl 2b
> +
> + /* LPDDR Soft Reset Mobile/Low Power DDR SDRAM. */
> + ldr r0, =IMX_ESD_BASE
> + ldr r4, =ACFG_ESDMISC_VAL
> + orr r1, r4, #ESDMISC_MDDR_DL_RST
> + str r1, [r0, #ESDMISC_ROF]
> +
> + /* Hold for more than 200ns */
> + ldr r1, =0x10000
> + 1: subs r1, r1, #0x1
> + bne 1b
> +
> + str r4, [r0]
> +
> + /* write32(ESDCFG0, ACFG_SDRAM_ESDCFG_REGISTER_VAL) */
Please avoid comments that paraphrase ASM in pseudo-C. Either remove
them or replace them with something that the ASM does not also say.
> + ldr r0, =IMX_ESD_BASE
> + ldr r1, =ACFG_SDRAM_ESDCFG_REGISTER_VAL
> + str r1, [r0, #ESDCFG0_ROF]
> +
> + /* write32(ESDCTL0, ACFG_PRECHARGE_CMD) */
> + ldr r0, =IMX_ESD_BASE
> + ldr r1, =ACFG_PRECHARGE_CMD
> + str r1, [r0, #ESDCTL0_ROF]
> +
> + /* write8(0xA0001000, any value) */
> + ldr r1, =PHYS_SDRAM_1+ACFG_SDRAM_PRECHARGE_ALL_VAL
> + strb r2, [r1]
> +
> + /* write32(ESDCTL0, ACFG_AUTOREFRESH_CMD) */
> + ldr r1, =ACFG_AUTOREFRESH_CMD
> + str r1, [r0, #ESDCTL0_ROF]
> +
> + ldr r4, =PHYS_SDRAM_1 /* CSD0 base address */
> +
> + ldr r6,=0x7 /* load loop counter */
> +1: str r5,[r4] /* run auto-refresh cycle to array 0 */
> + subs r6,r6,#1 /* decrease counter value */
> + bne 1b
> +
> + /* write32(ACFG_PRECHARGE_CMD, ACFG_SET_MODE_REG_CMD) */
> + ldr r1, =ACFG_SET_MODE_REG_CMD
> + str r1, [r0, #ESDCTL0_ROF]
> +
> + /* set standard mode register */
> + ldr r4, = PHYS_SDRAM_1+ACFG_SDRAM_MODE_REGISTER_VAL
> + strb r2, [r4]
> +
> + /* set extended mode register */
> + ldr r4, =PHYS_SDRAM_1+ACFG_SDRAM_EXT_MODE_REGISTER_VAL
> + strb r5, [r4]
> +
> + /* write32(ACFG_PRECHARGE_CMD, ACFG_NORMAL_RW_CMD) */
> + ldr r1, =ACFG_NORMAL_RW_CMD
> + str r1, [r0, #ESDCTL0_ROF]
> +
> + /* 2nd sdram */
> + /* write32(ESDCFG1, ACFG_SDRAM_ESDCFG_REGISTER_VAL ) */
> + ldr r0, =IMX_ESD_BASE
> + ldr r1, =ACFG_SDRAM_ESDCFG_REGISTER_VAL
> + str r1, [r0, #ESDCFG1_ROF]
> +
> + /* write32(ESDCTL1, ACFG_PRECHARGE_CMD) */
> + ldr r0, =IMX_ESD_BASE
> + ldr r1, =ACFG_PRECHARGE_CMD
> + str r1, [r0, #ESDCTL1_ROF]
> +
> + /* write8(0xB0001000, any value) */
> + ldr r1, =PHYS_SDRAM_2+ACFG_SDRAM_PRECHARGE_ALL_VAL
> + strb r2, [r1]
> +
> + /* write32(ESDCTL1, ACFG_AUTOREFRESH_CMD) */
> + ldr r1, =ACFG_AUTOREFRESH_CMD
> + str r1, [r0, #ESDCTL1_ROF]
> +
> + ldr r4, =PHYS_SDRAM_2 /* CSD1 base address */
> +
> + ldr r6,=0x7 /* load loop counter */
> +1: str r5,[r4] /* run auto-refresh cycle to array 0 */
> + subs r6,r6,#1 /* decrease counter value */
> + bne 1b
> +
> + /* write32(ESDCTL1, ACFG_SET_MODE_REG_CMD) */
> + ldr r1, =ACFG_SET_MODE_REG_CMD
> + str r1, [r0, #ESDCTL1_ROF]
> +
> + /* set standard mode register */
> + ldr r4, =PHYS_SDRAM_2+ACFG_SDRAM_MODE_REGISTER_VAL
> + strb r2, [r4]
> +
> + /* set extended mode register */
> + ldr r4, =PHYS_SDRAM_2+ACFG_SDRAM_EXT_MODE_REGISTER_VAL
> + strb r2, [r4]
> +
> + /* write32(ESDCTL1, ACFG_NORMAL_RW_CMD) */
> + ldr r1, =ACFG_NORMAL_RW_CMD
> + str r1, [r0, #ESDCTL1_ROF]
> +
> + mov pc, lr
> +
> diff --git a/board/armadeus/apf27/u-boot-spl.lds b/board/armadeus/apf27/u-boot-spl.lds
> new file mode 100644
> index 0000000..fdd52f2
> --- /dev/null
> +++ b/board/armadeus/apf27/u-boot-spl.lds
> @@ -0,0 +1,87 @@
> +/*
> + * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
> + * on behalf of DENX Software Engineering GmbH
> + *
> + * January 2004 - Changed to support H4 device
> + * Copyright (c) 2004-2008 Texas Instruments
> + *
> + * (C) Copyright 2002
> + * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +
> +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
> +OUTPUT_ARCH(arm)
> +ENTRY(_start)
> +SECTIONS
> +{
> + . = 0xA0fff800;
> +
> + . = ALIGN(4);
> + .text :
> + {
> + board/armadeus/apf27/start.o (.text)
> + *(.text)
> + }
> +
> + . = ALIGN(4);
> + .rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
> +
> + . = ALIGN(4);
> + .data : {
> + *(.data)
> + }
> +
> + . = ALIGN(4);
> + __u_boot_cmd_start = .;
> + .u_boot_cmd : { *(.u_boot_cmd) }
> + __u_boot_cmd_end = .;
> +
> + . = ALIGN(4);
> +
> + .rel.dyn : {
> + __rel_dyn_start = .;
> + *(.rel*)
> + __rel_dyn_end = .;
> + }
> +
> + .dynsym : {
> + __dynsym_start = .;
> + *(.dynsym)
> + }
> +
> + .bss : {
> + . = ALIGN(4);
> + __bss_start = .;
> + *(.bss*)
> + . = ALIGN(4);
> + __bss_end__ = .;
> + }
> +
> + _end = .;
> +
> + /DISCARD/ : { *(.dynstr*) }
> + /DISCARD/ : { *(.dynsym*) }
> + /DISCARD/ : { *(.dynamic*) }
> + /DISCARD/ : { *(.hash*) }
> + /DISCARD/ : { *(.plt*) }
> + /DISCARD/ : { *(.interp*) }
> + /DISCARD/ : { *(.gnu*) }
> +}
Amicalement,
--
Albert.
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 2/4] apf27: add support for the armadeus APF27 board
2012-11-26 17:55 ` Albert ARIBAUD
@ 2012-12-02 17:07 ` trem
0 siblings, 0 replies; 10+ messages in thread
From: trem @ 2012-12-02 17:07 UTC (permalink / raw)
To: u-boot
On 26/11/12 18:55, Albert ARIBAUD wrote:
>> +/*
>> + * Fuse bank 1 row 8 is "reserved for future use" and therefore available for
>> + * custormer use. The APF27 board uses this fuse to store the board revision:
>> + * 0: initial board revision
>> + * 1: first revision - Presence of the second RAM chip on the board is blown in
>> + * fuse bank 1 row 9 bit 0 - No hardware change
>> + * N: to be defined
>
> (aside: I am somewhat surprised that something "reserved for future
> use" can be considered "available for customer use": reserved areas
> are... reserved... thus probably not available -- future revisions of
> the *IC* may actually exercize the reservation, causing a conflict
> with the *board* assumptions. But hey, that's not a U-boot issue)
This is a reference to the freescale documentation.
It means that customer (here Armadeus) can use it to store
informations.
...
>> +int
>> +misc_init_r(void)
>> +{
>> + char *s;
>> + u_char * firmware_buffer = (u_char *)(CONFIG_SYS_LOAD_ADDR + \
>> + CONFIG_SYS_MONITOR_LEN);
>> + size_t size = 0;
>> + size_t offset = -1;
>> + char *autoload = getenv("firmware_autoload");
>
> Is this used?
Yes, this function can be used if it's enable in the u-boot environment.
...
>> +{
>> + /* Enable D-cache. I-cache is already enabled in start.S */
>> + dcache_enable();
>> +}
>> +
>> +inline void lowlevel_init(void) {}
>
> What's the point of defining lowlevel_init? If you don't do low level
> inits, then you can define CONFIG_SKIP_LOWLEVEL_INIT in the board
> config header file.
In fact lowlevel_init isn't only the call of a function, this is also
some "low level" init (like cache). I need this low level init, but
I don't need to call a function, so I only define an empty function.
...
regards,
Philippe
^ permalink raw reply [flat|nested] 10+ messages in thread
* [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27
2012-11-26 18:02 ` Albert ARIBAUD
@ 2012-12-02 17:09 ` trem
0 siblings, 0 replies; 10+ messages in thread
From: trem @ 2012-12-02 17:09 UTC (permalink / raw)
To: u-boot
On 26/11/12 19:02, Albert ARIBAUD wrote:
> Hi Philippe,
>
> On Mon, 29 Oct 2012 18:35:56 +0100, Philippe Reynes<tremyfr@yahoo.fr>
> wrote:
>
>> Signed-off-by: Philippe Reynes<tremyfr@yahoo.fr>
>> Signed-off-by: Eric Jarrige<eric.jarrige@armadeus.org>
>>
>> create mode 100644 board/armadeus/apf27/start.S
>> create mode 100644 board/armadeus/apf27/u-boot-spl.lds
>
> This is needed by 2/4 to get truly useable support. Please merge both
> patches.
I've done it, and send a v3 this weed-end.
Thanks a lot for the review.
regards,
Philippe
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2012-12-02 17:09 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-10-29 17:35 [U-Boot] [PATCH 0/4] apf27: add support of armadeus apf27 v2 Philippe Reynes
2012-10-29 17:35 ` [U-Boot] [PATCH 1/4] apf27: add missing constant to mx27 Philippe Reynes
2012-10-29 17:35 ` [U-Boot] [PATCH 2/4] apf27: add support for the armadeus APF27 board Philippe Reynes
2012-11-26 17:55 ` Albert ARIBAUD
2012-12-02 17:07 ` trem
2012-10-29 17:35 ` [U-Boot] [PATCH 3/4] apf27: add spl support for the apf27 Philippe Reynes
2012-10-30 20:50 ` Fabio Estevam
2012-11-26 18:02 ` Albert ARIBAUD
2012-12-02 17:09 ` trem
2012-10-29 17:35 ` [U-Boot] [PATCH 4/4] apf27: add FPGA support for the apf27 board Philippe Reynes
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox