From: Troy Kisky <troy.kisky@boundarydevices.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH V3 0/9] separate miiphy from ethernet
Date: Tue, 22 Jan 2013 16:48:04 -0700 [thread overview]
Message-ID: <50FF2534.4090306@boundarydevices.com> (raw)
In-Reply-To: <509E0212.3010609@denx.de>
On 11/10/2012 12:28 AM, Stefano Babic wrote:
> On 23/10/2012 04:40, Troy Kisky wrote:
>> This series tries to separate the mii regsisters
>> from the ethernet registers as suggested by
>> Andy Fleming. Then, mx6qsabrelite is changed
>> to find the phy address from the possibles 4-7.
>>
>> The V3 series is very different from V2.
>>
>> Troy Kisky (9):
>> doc/README.fec_mxc: add documentation
>> net: fec_mxc: delete CONFIG_FEC_MXC_MULTI
>> net: fec_mxc: change fec_mii_setspeed parameter
>> net: fec_mxc: have fecmxc_initialize call fecmxc_initialize_multi
>> phy: add phy_find_by_mask/phy_connect_dev
>> net: fec_mxc: use fec_set_dev_name to set name
>> net: fec_mxc: only call phy_connect in fec_probe
>> net: fec_mxc: get phydev before fec_probe
>> mx6qsabrelite: search mii phy address 4-7
>>
> Hi Joe,
>
>> board/freescale/mx6qsabrelite/mx6qsabrelite.c | 24 +++-
>> doc/README.fec_mxc | 27 ++++
>> drivers/net/fec_mxc.c | 164 ++++++++++++++-----------
>> drivers/net/fec_mxc.h | 2 +-
>> drivers/net/phy/phy.c | 128 +++++++++++--------
>> include/configs/m28evk.h | 1 -
>> include/configs/mx28evk.h | 1 -
>> include/configs/sc_sps_1.h | 1 -
>> include/netdev.h | 7 ++
>> include/phy.h | 3 +
>> 10 files changed, 227 insertions(+), 131 deletions(-)
>> create mode 100644 doc/README.fec_mxc
> Patches are assigned to me in patchworks. Do you have any issue with
> this patchset ? If it is ok for you, I will apply it to u-boot-imx.
>
> Best regards,
> Stefano
>
>
Who should I pester to see some progress on this ?
Thanks
Troy
next prev parent reply other threads:[~2013-01-22 23:48 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-08-20 22:48 [U-Boot] [PATCH V1 1/3] phy: add phy_connect_by_mask Troy Kisky
2012-08-20 22:48 ` [U-Boot] [PATCH V1 2/3] fec_mxc: use phy_connect_by_mask Troy Kisky
2012-08-20 22:48 ` [U-Boot] [PATCH V1 3/3] mx6qsabrelite: set CONFIG_FEC_MXC_PHYMASK Troy Kisky
2012-08-20 23:07 ` [U-Boot] [PATCH V1 1/3] phy: add phy_connect_by_mask Troy Kisky
2012-08-21 0:35 ` Andy Fleming
2012-08-22 19:59 ` Troy Kisky
2012-08-22 20:40 ` Andy Fleming
2012-08-22 20:50 ` Joe Hershberger
2012-08-22 21:21 ` Troy Kisky
2012-09-26 17:26 ` Joe Hershberger
2012-09-26 17:47 ` Troy Kisky
2012-08-22 20:11 ` Eric Nelson
2012-08-22 20:50 ` Andy Fleming
2012-08-22 20:56 ` Eric Nelson
2012-10-23 2:40 ` [U-Boot] [PATCH V3 0/9] separate miiphy from ethernet Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 1/9] doc/README.fec_mxc: add documentation Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 2/9] net: fec_mxc: delete CONFIG_FEC_MXC_MULTI Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 3/9] net: fec_mxc: change fec_mii_setspeed parameter Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 4/9] net: fec_mxc: have fecmxc_initialize call fecmxc_initialize_multi Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 5/9] phy: add phy_find_by_mask/phy_connect_dev Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 6/9] net: fec_mxc: use fec_set_dev_name to set name Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 7/9] net: fec_mxc: only call phy_connect in fec_probe Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 8/9] net: fec_mxc: get phydev before fec_probe Troy Kisky
2012-10-23 2:40 ` [U-Boot] [PATCH V3 9/9] mx6qsabrelite: search mii phy address 4-7 Troy Kisky
2012-11-10 7:28 ` [U-Boot] [PATCH V3 0/9] separate miiphy from ethernet Stefano Babic
2013-01-22 23:48 ` Troy Kisky [this message]
2013-01-23 8:48 ` Stefano Babic
2013-01-23 19:06 ` Troy Kisky
2013-01-24 9:09 ` Stefano Babic
2013-01-23 22:35 ` Troy Kisky
2013-01-03 22:00 ` Troy Kisky
2013-01-28 6:00 ` Stefano Babic
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=50FF2534.4090306@boundarydevices.com \
--to=troy.kisky@boundarydevices.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox