From: Tom Rini <trini@ti.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] am33xx config_ddr api change needed to support mDDR
Date: Wed, 6 Feb 2013 11:47:31 -0500 [thread overview]
Message-ID: <51128923.4000403@ti.com> (raw)
In-Reply-To: <CAOFKi=Zu7HfxSaV=m00UH9D1=NTB+mmBtK929UifTzW8ZeJQ6Q@mail.gmail.com>
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
On 02/05/2013 03:48 AM, Markus Brunner wrote:
> Hi, for mDDR to work mddr_sel (bit 28) of ddrctrl->ddrioctrl has to
> be set. There is no way of telling config_ddr(unsigned int pll,
> unsigned int ioctrl, ...) my desired value, it won't be set atm.
>
> From the 1.3kB ddr_ctrl struct only 2 registers are defined, which
> is fine if it's used memory mapped, however it makes it unsuitable
> for passing values in the SPL. So at first glance I would extend
> config_ddr() with an additional register value, because guessing
> the ddr type from the values of the other parameters is, in
> addition to being hackish, not guaranteed to work with every weired
> ram configuration. However might it be possible, that the second
> value of config_ddr() should not hold the value for
> config_io_ctrl(), but the value of my desired ddrctrl->ddrioctrl?
> The wiki [1] from TI says that the first should _always_ be 0x18B,
> whereas the second needs to be set depending on the mem type. We
> are talking about a set of registers named DDR_*_IOCTRL and a
> single register called DDR_IO_CTRL, so easy to mix up.
>
> Ragards, Markus
>
> [1]
> http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Hadn't
>
seen that wiki page before, thanks. So a problem right now is
that yes, I hadn't seen "in the wild" anything but DDR2 or DDR3
designs. I'm going to assume that on your custom hardware you are not
doing the EEPROM-based board detection method that the TI boards do.
We should try and lay things out so that boards where we can run-time
say "we are on board X (rev Y) and must have ..." can all out the same
functions for boards where we simply have to set that at build time
(until we get to the some-day of using a device tree or something like
that perhaps).
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/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=u++P
-----END PGP SIGNATURE-----
next prev parent reply other threads:[~2013-02-06 16:47 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-05 8:48 [U-Boot] am33xx config_ddr api change needed to support mDDR Markus Brunner
2013-02-06 16:47 ` Tom Rini [this message]
2013-02-07 8:48 ` Markus Brunner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=51128923.4000403@ti.com \
--to=trini@ti.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox