From mboxrd@z Thu Jan 1 00:00:00 1970 From: Troy Kisky Date: Fri, 22 Feb 2013 14:30:21 -0700 Subject: [U-Boot] [PATCH v7 15/19] nand: mxc: Switch NAND SPL to generic SPL In-Reply-To: <708859548.67831.1361567593481.JavaMail.root@advansee.com> References: <1360961665-10693-1-git-send-email-benoit.thebaudeau@advansee.com> <1360961665-10693-15-git-send-email-benoit.thebaudeau@advansee.com> <1520555937.67335.1361563759793.JavaMail.root@advansee.com> <708859548.67831.1361567593481.JavaMail.root@advansee.com> Message-ID: <5127E36D.9000304@boundarydevices.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On 2/22/2013 2:13 PM, Beno?t Th?baudeau wrote: > Hi Fabio, > > On Friday, February 22, 2013 10:06:42 PM, Fabio Estevam wrote: >> Hi Beno?t, >> >> On Fri, Feb 22, 2013 at 5:09 PM, Beno?t Th?baudeau >> wrote: >> >>> It looks very much like the issue that Marek had on i.MX53 (which >>> self-resolved >>> for an unknown reason). >>> >>> Try to enable the debug trace to see if anything else is printed after >>> display_dram_config(). I would especially be interested in: >>> debug("relocation Offset is: %08lx\n", gd->reloc_off); >>> debug("monitor flash len: %08lX\n", monitor_flash_len); >> Here is the output: >> >> U-Boot 2013.01 (Feb 22 2013 - 18:00:50) >> >> U-Boot code: 87F00000 -> 87F2C184 BSS: -> 87F311B4 >> CPU: Freescale i.MX31 rev 2.0 at 532 MHz. >> Reset cause: POR >> Board: MX31PDK >> monitor len: 000311B4 >> ramsize: 08000000 >> TLB table from 87ff0000 to 87ff4000 >> Top of RAM usable for U-Boot at: 87ff0000 >> Reserving 196k for U-Boot at: 87fbe000 >> Reserving 640k for malloc() at: 87f1e000 >> Reserving 32 Bytes for Board Info at: 87f1dfe0 >> Reserving 128 Bytes for Global Data at: 87f1df60 >> New Stack Pointer is: 87f1df50 >> RAM Configuration: >> Bank #0: 80000000 128 MiB >> relocation Offset is: 000be000 > CONFIG_SYS_TEXT_BASE seems fine according to this trace. But anyway, can you > test with this change in mx31pdk.h? > #define CONFIG_SPL_TEXT_BASE 0x84000000 > #define CONFIG_SYS_TEXT_BASE 0x83000000 > > Can you try to revert 10/19, only for arm1136/start.S (1 line to restore)? There > is an issue in this patch that I have already fixed in my v8. > > Best regards, > Beno?t > _______________________________________________ > How about changing #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x30000 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x32000 is see monitor len: 311B4 above is over 0x30000 Please excuse me if they are unrelated. Troy