[U-Boot] [PATCH v2 3/4][resend] arm: at91: add at91sam9n12ek board support

[Josh Wu <josh.wu@atmel.com>]

Hi, Shen Bo

On 3/22/2013 1:29 PM, Bo Shen wrote:
> Hi Josh,
>   minor comment as following.
>
> On 3/21/2013 9:52, Josh Wu wrote:
>> Add support for following features:
>>    - nand boot, with PMECC 2bit ECC for 512 bytes sector
>>    - SPI flash boot
>>    - SD card boot
>>    - LCD support
>>
>> Signed-off-by: Josh Wu <josh.wu@atmel.com>
>> ---
>>   MAINTAINERS                                       |    3 +
>>   arch/arm/cpu/arm926ejs/at91/Makefile              |    1 +
>>   arch/arm/cpu/arm926ejs/at91/at91sam9n12_devices.c |  180 
>> ++++++++++++++++
>>   arch/arm/cpu/arm926ejs/at91/clock.c               |    4 +-
>>   board/atmel/at91sam9n12ek/Makefile                |   52 +++++
>>   board/atmel/at91sam9n12ek/at91sam9n12ek.c         |  228 
>> ++++++++++++++++++++
>>   boards.cfg                                        |    3 +
>>   include/configs/at91sam9n12ek.h                   |  232 
>> +++++++++++++++++++++
>>   8 files changed, 701 insertions(+), 2 deletions(-)
>>   create mode 100644 arch/arm/cpu/arm926ejs/at91/at91sam9n12_devices.c
>>   create mode 100644 board/atmel/at91sam9n12ek/Makefile
>>   create mode 100644 board/atmel/at91sam9n12ek/at91sam9n12ek.c
>>   create mode 100644 include/configs/at91sam9n12ek.h
>>
>
> [snip]
>
>> +#ifdef CONFIG_LCD
>> +void at91_lcd_hw_init(void)
>> +{
>> +    struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
>> +
>> +    at91_set_a_periph(AT91_PIO_PORTC, 24, 0);    /* LCDDPWR */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 26, 0);    /* LCDVSYNC */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 27, 0);    /* LCDHSYNC */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 28, 0);    /* LCDDOTCK */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 29, 0);    /* LCDDEN */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 30, 0);    /* LCDDOTCK */
>> +
>> +    at91_set_a_periph(AT91_PIO_PORTC, 0, 0);    /* LCDD0 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 1, 0);    /* LCDD1 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 2, 0);    /* LCDD2 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 3, 0);    /* LCDD3 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 4, 0);    /* LCDD4 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 5, 0);    /* LCDD5 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 6, 0);    /* LCDD6 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 7, 0);    /* LCDD7 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 8, 0);    /* LCDD8 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 9, 0);    /* LCDD9 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 10, 0);    /* LCDD10 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 11, 0);    /* LCDD11 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 12, 0);    /* LCDD12 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 13, 0);    /* LCDD13 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 14, 0);    /* LCDD14 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 15, 0);    /* LCDD15 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 16, 0);    /* LCDD16 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 17, 0);    /* LCDD17 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 18, 0);    /* LCDD18 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 19, 0);    /* LCDD19 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 20, 0);    /* LCDD20 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 21, 0);    /* LCDD21 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 22, 0);    /* LCDD22 */
>> +    at91_set_a_periph(AT91_PIO_PORTC, 23, 0);    /* LCDD23 */
>> +
>> +    writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
>> +}
>> +#endif
>> +
>> +
>> +
>
> when apply this patch, it will show following warning:
>
> .git/rebase-apply/patch:225: new blank line at EOF.
> +
> warning: 1 line adds whitespace errors.

ok, I will fix the blank line in v3. thanks.

Best Regards,
Josh Wu

>
> Best Regards,
> Bo Shen
>