[U-Boot] [PATCH] nitrogen6x: Setup CCM_CCOSR register

[U-Boot] [PATCH] nitrogen6x: Setup CCM_CCOSR register

[Fabio Estevam]

From: Fabio Estevam <fabio.estevam@freescale.com>

CKO1 drives sgtl5000 codec clock on nitrogen boards and wandboard.

Doing this setup in the bootloader will allow us to remove a lot of code in 
arch/arm/mach-imx/mach-imx6q.c from the mainline kernel.

Also, according to Eric Nelson: "enabling the clock <in the bootloader> will 
remove squeal after an ungraceful reboot (watchdog) if hooked up to speakers."

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
---
 arch/arm/include/asm/arch-mx6/crm_regs.h |    1 +
 board/boundary/nitrogen6x/clocks.cfg     |   11 +++++++++++
 2 files changed, 12 insertions(+)

diff --git a/arch/arm/include/asm/arch-mx6/crm_regs.h b/arch/arm/include/asm/arch-mx6/crm_regs.h
index 7676457..ca732af 100644
--- a/arch/arm/include/asm/arch-mx6/crm_regs.h
+++ b/arch/arm/include/asm/arch-mx6/crm_regs.h
@@ -20,6 +20,7 @@
 #ifndef __ARCH_ARM_MACH_MX6_CCM_REGS_H__
 #define __ARCH_ARM_MACH_MX6_CCM_REGS_H__
 
+#define CCM_CCOSR		0x020c4060
 #define CCM_CCGR0		0x020C4068
 #define CCM_CCGR1		0x020C406c
 #define CCM_CCGR2		0x020C4070
diff --git a/board/boundary/nitrogen6x/clocks.cfg b/board/boundary/nitrogen6x/clocks.cfg
index e7d1f86..0a3b47b 100644
--- a/board/boundary/nitrogen6x/clocks.cfg
+++ b/board/boundary/nitrogen6x/clocks.cfg
@@ -44,3 +44,14 @@ DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
 /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
 DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
 DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
+
+/*
+ * Setup CCM_CCOSR register as follows:
+ *
+ * cko1_en  = 1	   --> CKO1 enabled
+ * cko1_div = 111  --> divide by 8
+ * cko1_sel = 1011 --> ahb_clk_root
+ *
+ * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz
+ */
+DATA 4, CCM_CCOSR, 0x000000fb
-- 
1.7.9.5

[U-Boot] [PATCH] nitrogen6x: Setup CCM_CCOSR register

[Stefano Babic]

On 18/04/2013 01:09, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam@freescale.com>
> 
> CKO1 drives sgtl5000 codec clock on nitrogen boards and wandboard.
> 
> Doing this setup in the bootloader will allow us to remove a lot of code in 
> arch/arm/mach-imx/mach-imx6q.c from the mainline kernel.
> 
> Also, according to Eric Nelson: "enabling the clock <in the bootloader> will 
> remove squeal after an ungraceful reboot (watchdog) if hooked up to speakers."
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---


Applied to u-boot-imx, -next branch, thanks.

Best regards,
Stefano Babic


-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================