[U-Boot] [PATCH v3 1/3] iomux-v3: Place pad control definitions into common file

[Stefano Babic <sbabic@denx.de>]

On 10/04/2013 21:32, festevam at gmail.com wrote:
> From: Fabio Estevam <fabio.estevam@freescale.com>
> 
> Instead of having the same PAD control definition in each MX6 variant pin file,
> place it into a common location.
> 
> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
> ---

Hi Fabio,

> Changes since v2:
> - None
> Changes since v1:
> - Add missing IOMUX_CONFIG_SION definition to avoid breakage on mx6dl
> 
>  arch/arm/include/asm/arch-mx6/mx6dl_pins.h |   27 ---------------------------
>  arch/arm/include/asm/arch-mx6/mx6q_pins.h  |   27 ---------------------------
>  arch/arm/include/asm/imx-common/iomux-v3.h |   27 ++++++++++++++++++++++++++-
>  3 files changed, 26 insertions(+), 55 deletions(-)
> 
> diff --git a/arch/arm/include/asm/arch-mx6/mx6dl_pins.h b/arch/arm/include/asm/arch-mx6/mx6dl_pins.h
> index 9846f1b..0ed12f3 100644
> --- a/arch/arm/include/asm/arch-mx6/mx6dl_pins.h
> +++ b/arch/arm/include/asm/arch-mx6/mx6dl_pins.h
> @@ -22,33 +22,6 @@
>  
>  #include <asm/imx-common/iomux-v3.h>
>  
> -/* Use to set PAD control */
> -#define PAD_CTL_HYS		(1 << 16)
> -#define PAD_CTL_PUS_100K_DOWN	(0 << 14)
> -#define PAD_CTL_PUS_47K_UP	(1 << 14)
> -#define PAD_CTL_PUS_100K_UP	(2 << 14)
> -#define PAD_CTL_PUS_22K_UP	(3 << 14)
> -
> -#define PAD_CTL_PUE		(1 << 13)
> -#define PAD_CTL_PKE		(1 << 12)
> -#define PAD_CTL_ODE		(1 << 11)
> -#define PAD_CTL_SPEED_LOW	(1 << 6)
> -#define PAD_CTL_SPEED_MED	(2 << 6)
> -#define PAD_CTL_SPEED_HIGH	(3 << 6)
> -#define PAD_CTL_DSE_DISABLE	(0 << 3)
> -#define PAD_CTL_DSE_240ohm	(1 << 3)
> -#define PAD_CTL_DSE_120ohm	(2 << 3)
> -#define PAD_CTL_DSE_80ohm	(3 << 3)
> -#define PAD_CTL_DSE_60ohm	(4 << 3)
> -#define PAD_CTL_DSE_48ohm	(5 << 3)
> -#define PAD_CTL_DSE_40ohm	(6 << 3)
> -#define PAD_CTL_DSE_34ohm	(7 << 3)
> -#define PAD_CTL_SRE_FAST	(1 << 0)
> -#define PAD_CTL_SRE_SLOW	(0 << 0)
> -

I have applied this patch and I have found now that this breaks some
MX51 boards, such as efika. In fact, the same defines are set also in
/home/stefano/Projects/imx/u-boot-imx/include/asm/arch/iomux-mx51.h.

Checking in the manual, I see that values in iomux-mx51.h are correct,
and they simply differs from the ones of MX6. We can simply add a #ifdef
CONFIG_MX51 in arch/arm/include/asm/imx-common/iomux-v3.h to fix it, but
anyway I suppose that the mx51evk does not work correctly. Can you take
a look at this issue ?

Best regards,
Stefano

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================