From: Lubomir Popov <lpopov@mm-sol.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v3 0/6] Optimize ARM relocation
Date: Tue, 11 Jun 2013 17:22:17 +0300 [thread overview]
Message-ID: <51B73299.2050002@mm-sol.com> (raw)
In-Reply-To: <20130611144729.5bbf542b@lilith>
Hi Albert,
On 11/06/13 15:47, Albert ARIBAUD wrote:
> Hi Albert,
>
> On Tue, 11 Jun 2013 14:17:29 +0200, Albert ARIBAUD
> <albert.u.boot@aribaud.net> wrote:
>
>> This series optimizes relocation by ensuring ARM
>> binaries only use one type of relocation record,
>> R_ARM_RELATIVE., then optimizing relocation code
>> accordingly.
>
> This is a cosmetic version only; if no one complains loudly, this
> will be the final version too.
>
> So people, as this touches ARM relocation, I would appreciate it if a
> few people could test it on their own ARM HW target and see if they
> still get a prompt, if command completion still works, etc.
Applied the series to a relatively fresh (yesterday's) u-boot-ti/master
and tested on a custom OMAP5430 board. Boots normally. USB storage and
Ethernet (dhcp & ping), SD/MMC, I2C are all working.
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Regards,
Lubo
next prev parent reply other threads:[~2013-06-11 14:22 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-14 20:02 [U-Boot] [PATCH 0/5] Optimize ARM relocation Albert ARIBAUD
2013-05-14 20:02 ` [U-Boot] [PATCH 1/5] arm: generalize lib/bss.c into lib/sections.c Albert ARIBAUD
2013-05-14 20:02 ` [U-Boot] [PATCH 2/5] arm: make __image_copy_{start, end} compiler-generated Albert ARIBAUD
2013-05-14 20:02 ` [U-Boot] [PATCH 3/5] arm: make relocation symbols compiler-generated Albert ARIBAUD
2013-05-14 20:02 ` [U-Boot] [PATCH 4/5] arm: ensure u-boot only uses relative relocations Albert ARIBAUD
2013-05-14 20:03 ` [U-Boot] [PATCH 5/5] arm: optimize relocate_code routine Albert ARIBAUD
2013-05-14 23:54 ` Benoît Thébaudeau
2013-05-15 7:32 ` Albert ARIBAUD
2013-05-14 22:12 ` [U-Boot] [PATCH 4/5] arm: ensure u-boot only uses relative relocations Benoît Thébaudeau
2013-05-15 7:46 ` Albert ARIBAUD
2013-05-15 9:38 ` Albert ARIBAUD
2013-05-15 13:49 ` Benoît Thébaudeau
2013-05-15 15:01 ` Albert ARIBAUD
2013-05-14 22:09 ` [U-Boot] [PATCH 3/5] arm: make relocation symbols compiler-generated Benoît Thébaudeau
2013-05-15 6:39 ` Albert ARIBAUD
2013-05-15 6:41 ` Albert ARIBAUD
2013-05-14 20:16 ` [U-Boot] [PATCH 0/5] Optimize ARM relocation Albert ARIBAUD
2013-05-14 23:58 ` Benoît Thébaudeau
2013-05-15 7:49 ` Albert ARIBAUD
2013-05-28 7:01 ` [U-Boot] [PATCH v2 0/6] " Albert ARIBAUD
2013-05-28 7:01 ` [U-Boot] [PATCH v2 1/6] arm: ensure u-boot only uses relative relocations Albert ARIBAUD
2013-05-28 7:01 ` [U-Boot] [PATCH v2 2/6] remove all references to .dynsym Albert ARIBAUD
2013-05-28 7:01 ` [U-Boot] [PATCH v2 3/6] arm: generalize lib/bss.c into lib/sections.c Albert ARIBAUD
2013-05-28 7:01 ` [U-Boot] [PATCH v2 4/6] arm: make __image_copy_{start, end} compiler-generated Albert ARIBAUD
2013-05-28 7:01 ` [U-Boot] [PATCH v2 5/6] arm: make __rel_dyn_{start, " Albert ARIBAUD
2013-05-28 7:01 ` [U-Boot] [PATCH v2 6/6] arm: optimize relocate_code routine Albert ARIBAUD
2013-05-28 17:11 ` [U-Boot] [PATCH v2 4/6] arm: make __image_copy_{start, end} compiler-generated Benoît Thébaudeau
2013-05-28 17:04 ` [U-Boot] [PATCH v2 1/6] arm: ensure u-boot only uses relative relocations Benoît Thébaudeau
2013-05-28 17:31 ` Albert ARIBAUD
2013-06-11 12:17 ` [U-Boot] [PATCH v3 0/6] Optimize ARM relocation Albert ARIBAUD
2013-06-11 12:17 ` [U-Boot] [PATCH v3 1/6] arm: ensure u-boot only uses relative relocations Albert ARIBAUD
2013-06-11 12:17 ` [U-Boot] [PATCH v3 2/6] remove all references to .dynsym Albert ARIBAUD
2013-06-11 12:17 ` [U-Boot] [PATCH v3 3/6] arm: generalize lib/bss.c into lib/sections.c Albert ARIBAUD
2013-06-11 12:17 ` [U-Boot] [PATCH v3 4/6] arm: make __image_copy_{start, end} compiler-generated Albert ARIBAUD
2013-06-11 12:17 ` [U-Boot] [PATCH v3 5/6] arm: make __rel_dyn_{start, " Albert ARIBAUD
2013-06-11 12:17 ` [U-Boot] [PATCH v3 6/6] arm: optimize relocate_code routine Albert ARIBAUD
2013-06-11 12:47 ` [U-Boot] [PATCH v3 0/6] Optimize ARM relocation Albert ARIBAUD
2013-06-11 14:22 ` Lubomir Popov [this message]
2013-06-11 15:29 ` Albert ARIBAUD
2013-06-13 9:05 ` Albert ARIBAUD
2013-06-13 18:54 ` Jeroen Hofstee
2013-06-16 13:33 ` Jeroen Hofstee
2013-06-18 14:54 ` Albert ARIBAUD
2013-06-19 7:31 ` [U-Boot] [LONG] " Albert ARIBAUD
2013-06-12 22:38 ` [U-Boot] " Benoît Thébaudeau
2013-06-21 21:07 ` Albert ARIBAUD
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=51B73299.2050002@mm-sol.com \
--to=lpopov@mm-sol.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox