[U-Boot] [PATCH] am33xx: Enable D-CACHE on !CONFIG_SYS_DCACHE_OFF

[Lokesh Vutla <lokeshvutla@ti.com>]

Hi Tom,
On Saturday 31 August 2013 02:43 AM, Tom Rini wrote:
> On Fri, Aug 30, 2013 at 05:07:17PM -0400, Tom Rini wrote:
> 
>> -----BEGIN PGP SIGNED MESSAGE-----
>> Hash: SHA1
>>
>> On 08/30/2013 12:50 AM, Sricharan R wrote:
>>> Hi Tom,
>>>
>>> On Friday 23 August 2013 09:56 PM, Tom Rini wrote:
>>>> Test on Beaglebone white over cpsw, usb ether and SD card (read and
>>>> write), performance increased, crc32 of data matches.
>>>>
>>>> Signed-off-by: Tom Rini <trini@ti.com>
>>>> ---
>>>>  arch/arm/cpu/armv7/am33xx/board.c |    8 ++++++++
>>>>  1 file changed, 8 insertions(+)
>>>>
>>>> diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c
>>>> index 2ea3d69..c261af5 100644
>>>> --- a/arch/arm/cpu/armv7/am33xx/board.c
>>>> +++ b/arch/arm/cpu/armv7/am33xx/board.c
>>>> @@ -225,3 +225,11 @@ void s_init(void)
>>>>  	sdram_init();
>>>>  #endif
>>>>  }
>>>> +
>>>> +#ifndef CONFIG_SYS_DCACHE_OFF
>>>> +void enable_caches(void)
>>>> +{
>>>> +	/* Enable D-cache. I-cache is already enabled in start.S */
>>>> +	dcache_enable();
>>>> +}
>>>> +#endif /* !CONFIG_SYS_DCACHE_OFF */
>>>  This is fine. Do we have secure devices here ?
>>>
>>>  If so, we should take care of setting the domains permissions for
>>>  avoiding prefetch aborts. As it was done for OMAP using
>>>  arm_init_domains. So that function and the above should be executed on
>>>  am33xx as well.
>>>
>>>  Thanks to Lokesh for reminding this.
>>
>> Yes, but I can't easily test them.  I'll see if arm_init_domains just
>> works on non-HS devices (I know I had a failure pulling all the OMAP4
>> code over, but didn't try hard, just looked again at the "easy" path).
> 
> Yeah, that code as-is hangs the boards.  So if the HS devices need
> something, it'll go with the rest of their patches until we're moving it
> upstream.  But good to note a potential problem area!
I added the following diff and I am able to boot my BBB over cpsw.

diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c
index 2ea3d69..8a1a29a 100644
--- a/arch/arm/cpu/armv7/am33xx/board.c
+++ b/arch/arm/cpu/armv7/am33xx/board.c
@@ -31,6 +31,11 @@
 #include <linux/usb/gadget.h>
 #include <linux/usb/musb.h>
 #include <asm/omap_musb.h>
+#include <asm/cache.h>
+
+#define ARMV7_DCACHE_WRITEBACK  0xe
+#define ARMV7_DOMAIN_CLIENT	1
+#define ARMV7_DOMAIN_MASK	(0x3 << 0)
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -225,3 +230,40 @@ void s_init(void)
 	sdram_init();
 #endif
 }
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+void enable_caches(void)
+{
+	/* Enable D-cache. I-cache is already enabled in start.S */
+	dcache_enable();
+}
+
+void dram_bank_mmu_setup(int bank)
+{
+	bd_t *bd = gd->bd;
+	int	i;
+
+	u32 start = bd->bi_dram[bank].start >> 20;
+	u32 size = bd->bi_dram[bank].size >> 20;
+	u32 end = start + size;
+
+	debug("%s: bank: %d\n", __func__, bank);
+	for (i = start; i < end; i++)
+		set_section_dcache(i, ARMV7_DCACHE_WRITEBACK);
+
+}
+
+void arm_init_domains(void)
+{
+	u32 reg;
+
+	reg = get_dacr();
+	/*
+	* Set DOMAIN to client access so that all permissions
+	* set in pagetables are validated by the mmu.
+	*/
+	reg &= ~ARMV7_DOMAIN_MASK;
+	reg |= ARMV7_DOMAIN_CLIENT;
+	set_dacr(reg);
+}
+#endif

AM I missing something here ?

Thanks and regards,
Lokesh
> 
> 
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>