[U-Boot] [PATCH] i2c, zynq: convert zynq i2c driver to new multibus/multiadapter framework

[U-Boot] [PATCH] i2c, zynq: convert zynq i2c driver to new multibus/multiadapter framework

[Heiko Schocher]

- add zync i2c driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
---
 README                 |  5 +++++
 drivers/i2c/Makefile   |  2 +-
 drivers/i2c/zynq_i2c.c | 29 ++++++++++++++++-------------
 include/configs/zynq.h |  8 ++++----
 4 files changed, 26 insertions(+), 18 deletions(-)

diff --git a/README b/README
index 19aed51..1b9312f 100644
--- a/README
+++ b/README
@@ -2064,6 +2064,11 @@ CBFS (Coreboot Filesystem) support
 		  - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
 		  - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
 
+		- drivers/i2c/zynq_i2c.c
+		  - activate this driver with CONFIG_SYS_I2C_ZYNQ
+		  - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
+		  - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
+
 		additional defines:
 
 		CONFIG_SYS_NUM_I2C_BUSES
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 298b17b..9dd9094 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -28,4 +28,4 @@ obj-$(CONFIG_SYS_I2C_RCAR) += rcar_i2c.o
 obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o
 obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
 obj-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o
-obj-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o
+obj-$(CONFIG_SYS_I2C_ZYNQ) += zynq_i2c.o
diff --git a/drivers/i2c/zynq_i2c.c b/drivers/i2c/zynq_i2c.c
index ce2d23f..70a9aea 100644
--- a/drivers/i2c/zynq_i2c.c
+++ b/drivers/i2c/zynq_i2c.c
@@ -74,7 +74,8 @@ static struct zynq_i2c_registers *zynq_i2c =
 	(struct zynq_i2c_registers *)ZYNQ_I2C_BASE;
 
 /* I2C init called by cmd_i2c when doing 'i2c reset'. */
-void i2c_init(int requested_speed, int slaveadd)
+static void zynq_i2c_init(struct i2c_adapter *adap, int requested_speed,
+			  int slaveadd)
 {
 	/* 111MHz / ( (3 * 17) * 22 ) = ~100KHz */
 	writel((16 << ZYNQ_I2C_CONTROL_DIV_B_SHIFT) |
@@ -151,7 +152,7 @@ static u32 zynq_i2c_wait(u32 mask)
  * I2C probe called by cmd_i2c when doing 'i2c probe'.
  * Begin read, nak data byte, end.
  */
-int i2c_probe(u8 dev)
+static int zynq_i2c_probe(struct i2c_adapter *adap, u8 dev)
 {
 	/* Attempt to read a byte */
 	setbits_le32(&zynq_i2c->control, ZYNQ_I2C_CONTROL_CLR_FIFO |
@@ -170,7 +171,8 @@ int i2c_probe(u8 dev)
  * I2C read called by cmd_i2c when doing 'i2c read' and by cmd_eeprom.c
  * Begin write, send address byte(s), begin read, receive data bytes, end.
  */
-int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
+static int zynq_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr,
+			 int alen, u8 *data, int length)
 {
 	u32 status;
 	u32 i = 0;
@@ -235,7 +237,8 @@ int i2c_read(u8 dev, uint addr, int alen, u8 *data, int length)
  * I2C write called by cmd_i2c when doing 'i2c write' and by cmd_eeprom.c
  * Begin write, send address byte(s), send data bytes, end.
  */
-int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
+static int zynq_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr,
+			  int alen, u8 *data, int length)
 {
 	u8 *cur_data = data;
 
@@ -275,16 +278,16 @@ int i2c_write(u8 dev, uint addr, int alen, u8 *data, int length)
 	return 0;
 }
 
-int i2c_set_bus_num(unsigned int bus)
+static unsigned int zynq_i2c_set_bus_speed(struct i2c_adapter *adap,
+			unsigned int speed)
 {
-	/* Only support bus 0 */
-	if (bus > 0)
-		return -1;
-	return 0;
-}
+	if (speed != 1000000)
+		return -EINVAL;
 
-unsigned int i2c_get_bus_num(void)
-{
-	/* Only support bus 0 */
 	return 0;
 }
+
+U_BOOT_I2C_ADAP_COMPLETE(zynq_0, zynq_i2c_init, zynq_i2c_probe, zynq_i2c_read,
+			 zynq_i2c_write, zynq_i2c_set_bus_speed,
+			 CONFIG_SYS_I2C_ZYNQ_SPEED, CONFIG_SYS_I2C_ZYNQ_SLAVE,
+			 0)
diff --git a/include/configs/zynq.h b/include/configs/zynq.h
index 4c6e6e8..82ec826 100644
--- a/include/configs/zynq.h
+++ b/include/configs/zynq.h
@@ -60,10 +60,10 @@
 /* I2C */
 #if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1)
 # define CONFIG_CMD_I2C
-# define CONFIG_ZYNQ_I2C
-# define CONFIG_HARD_I2C
-# define CONFIG_SYS_I2C_SPEED		100000
-# define CONFIG_SYS_I2C_SLAVE		1
+# define CONFIG_SYS_I2C
+# define CONFIG_SYS_I2C_ZYNQ
+# define CONFIG_SYS_I2C_ZYNQ_SPEED		100000
+# define CONFIG_SYS_I2C_ZYNQ_SLAVE		1
 #endif
 
 #if defined(CONFIG_ZYNQ_DCC)
-- 
1.8.3.1

[U-Boot] [PATCH] i2c, omap1510: remove i2c driver

[Heiko Schocher]

remove omap1510 i2c driver, as there is no board which uses it

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
---
 drivers/i2c/Makefile       |   1 -
 drivers/i2c/omap1510_i2c.c | 277 ---------------------------------------------
 2 files changed, 278 deletions(-)
 delete mode 100644 drivers/i2c/omap1510_i2c.c

diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 9dd9094..553b519 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -11,7 +11,6 @@ obj-$(CONFIG_DW_I2C) += designware_i2c.o
 obj-$(CONFIG_I2C_MVTWSI) += mvtwsi.o
 obj-$(CONFIG_I2C_MV) += mv_i2c.o
 obj-$(CONFIG_I2C_MXS) += mxs_i2c.o
-obj-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o
 obj-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
 obj-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
 obj-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
diff --git a/drivers/i2c/omap1510_i2c.c b/drivers/i2c/omap1510_i2c.c
deleted file mode 100644
index f91ee88..0000000
--- a/drivers/i2c/omap1510_i2c.c
+++ /dev/null
@@ -1,277 +0,0 @@
-/*
- * Basic I2C functions
- *
- * Copyright (c) 2003 Texas Instruments
- *
- * This package is free software;  you can redistribute it and/or
- * modify it under the terms of the license found in the file
- * named COPYING that should have accompanied this file.
- *
- * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
- * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- *
- * Author: Jian Zhang jzhang at ti.com, Texas Instruments
- *
- * Copyright (c) 2003 Wolfgang Denk, wd at denx.de
- * Rewritten to fit into the current U-Boot framework
- *
- */
-
-#include <common.h>
-
-static void wait_for_bb (void);
-static u16 wait_for_pin (void);
-
-void i2c_init (int speed, int slaveadd)
-{
-	u16 scl;
-
-	if (inw (I2C_CON) & I2C_CON_EN) {
-		outw (0, I2C_CON);
-		udelay (5000);
-	}
-
-	/* 12MHz I2C module clock */
-	outw (0, I2C_PSC);
-	outw (I2C_CON_EN, I2C_CON);
-	outw (0, I2C_SYSTEST);
-	/* have to enable intrrupts or OMAP i2c module doesn't work */
-	outw (I2C_IE_XRDY_IE | I2C_IE_RRDY_IE | I2C_IE_ARDY_IE |
-	      I2C_IE_NACK_IE | I2C_IE_AL_IE, I2C_IE);
-	scl = (12000000 / 2) / speed - 6;
-	outw (scl, I2C_SCLL);
-	outw (scl, I2C_SCLH);
-	/* own address */
-	outw (slaveadd, I2C_OA);
-	outw (0, I2C_CNT);
-	udelay (1000);
-}
-
-static int i2c_read_byte (u8 devaddr, u8 regoffset, u8 * value)
-{
-	int i2c_error = 0;
-	u16 status;
-
-	/* wait until bus not busy */
-	wait_for_bb ();
-
-	/* one byte only */
-	outw (1, I2C_CNT);
-	/* set slave address */
-	outw (devaddr, I2C_SA);
-	/* no stop bit needed here */
-	outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX, I2C_CON);
-
-	status = wait_for_pin ();
-
-	if (status & I2C_STAT_XRDY) {
-		/* Important: have to use byte access */
-		*(volatile u8 *) (I2C_DATA) = regoffset;
-		udelay (20000);
-		if (inw (I2C_STAT) & I2C_STAT_NACK) {
-			i2c_error = 1;
-		}
-	} else {
-		i2c_error = 1;
-	}
-
-	if (!i2c_error) {
-		/* free bus, otherwise we can't use a combined transction */
-		outw (0, I2C_CON);
-		while (inw (I2C_STAT) || (inw (I2C_CON) & I2C_CON_MST)) {
-			udelay (10000);
-			/* Have to clear pending interrupt to clear I2C_STAT */
-			inw (I2C_IV);
-		}
-
-		wait_for_bb ();
-		/* set slave address */
-		outw (devaddr, I2C_SA);
-		/* read one byte from slave */
-		outw (1, I2C_CNT);
-		/* need stop bit here */
-		outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP,
-		      I2C_CON);
-
-		status = wait_for_pin ();
-		if (status & I2C_STAT_RRDY) {
-			*value = inw (I2C_DATA);
-			udelay (20000);
-		} else {
-			i2c_error = 1;
-		}
-
-		if (!i2c_error) {
-			outw (I2C_CON_EN, I2C_CON);
-			while (inw (I2C_STAT)
-			       || (inw (I2C_CON) & I2C_CON_MST)) {
-				udelay (10000);
-				inw (I2C_IV);
-			}
-		}
-	}
-
-	return i2c_error;
-}
-
-static int i2c_write_byte (u8 devaddr, u8 regoffset, u8 value)
-{
-	int i2c_error = 0;
-	u16 status;
-
-	/* wait until bus not busy */
-	wait_for_bb ();
-
-	/* two bytes */
-	outw (2, I2C_CNT);
-	/* set slave address */
-	outw (devaddr, I2C_SA);
-	/* stop bit needed here */
-	outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_TRX |
-	      I2C_CON_STP, I2C_CON);
-
-	/* wait until state change */
-	status = wait_for_pin ();
-
-	if (status & I2C_STAT_XRDY) {
-		/* send out two bytes */
-		outw ((value << 8) + regoffset, I2C_DATA);
-		/* must have enough delay to allow BB bit to go low */
-		udelay (30000);
-		if (inw (I2C_STAT) & I2C_STAT_NACK) {
-			i2c_error = 1;
-		}
-	} else {
-		i2c_error = 1;
-	}
-
-	if (!i2c_error) {
-		outw (I2C_CON_EN, I2C_CON);
-		while (inw (I2C_STAT) || (inw (I2C_CON) & I2C_CON_MST)) {
-			udelay (1000);
-			/* have to read to clear intrrupt */
-			inw (I2C_IV);
-		}
-	}
-
-	return i2c_error;
-}
-
-int i2c_probe (uchar chip)
-{
-	int res = 1;
-
-	if (chip == inw (I2C_OA)) {
-		return res;
-	}
-
-	/* wait until bus not busy */
-	wait_for_bb ();
-
-	/* try to read one byte */
-	outw (1, I2C_CNT);
-	/* set slave address */
-	outw (chip, I2C_SA);
-	/* stop bit needed here */
-	outw (I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP, I2C_CON);
-	/* enough delay for the NACK bit set */
-	udelay (2000);
-	if (!(inw (I2C_STAT) & I2C_STAT_NACK)) {
-		res = 0;
-	} else {
-		outw (inw (I2C_CON) | I2C_CON_STP, I2C_CON);
-		udelay (20);
-		wait_for_bb ();
-	}
-
-	return res;
-}
-
-int i2c_read (uchar chip, uint addr, int alen, uchar * buffer, int len)
-{
-	int i;
-
-	if (alen > 1) {
-		printf ("I2C read: addr len %d not supported\n", alen);
-		return 1;
-	}
-
-	if (addr + len > 256) {
-		printf ("I2C read: address out of range\n");
-		return 1;
-	}
-
-	for (i = 0; i < len; i++) {
-		if (i2c_read_byte (chip, addr + i, &buffer[i])) {
-			printf ("I2C read: I/O error\n");
-			i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-			return 1;
-		}
-	}
-
-	return 0;
-}
-
-int i2c_write (uchar chip, uint addr, int alen, uchar * buffer, int len)
-{
-	int i;
-
-	if (alen > 1) {
-		printf ("I2C read: addr len %d not supported\n", alen);
-		return 1;
-	}
-
-	if (addr + len > 256) {
-		printf ("I2C read: address out of range\n");
-		return 1;
-	}
-
-	for (i = 0; i < len; i++) {
-		if (i2c_write_byte (chip, addr + i, buffer[i])) {
-			printf ("I2C read: I/O error\n");
-			i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-			return 1;
-		}
-	}
-
-	return 0;
-}
-
-static void wait_for_bb (void)
-{
-	int timeout = 10;
-
-	while ((inw (I2C_STAT) & I2C_STAT_BB) && timeout--) {
-		inw (I2C_IV);
-		udelay (1000);
-	}
-
-	if (timeout <= 0) {
-		printf ("timed out in wait_for_bb: I2C_STAT=%x\n",
-			inw (I2C_STAT));
-	}
-}
-
-static u16 wait_for_pin (void)
-{
-	u16 status, iv;
-	int timeout = 10;
-
-	do {
-		udelay (1000);
-		status = inw (I2C_STAT);
-		iv = inw (I2C_IV);
-	} while (!iv &&
-		 !(status &
-		   (I2C_STAT_ROVR | I2C_STAT_XUDF | I2C_STAT_XRDY |
-		    I2C_STAT_RRDY | I2C_STAT_ARDY | I2C_STAT_NACK |
-		    I2C_STAT_AL)) && timeout--);
-
-	if (timeout <= 0) {
-		printf ("timed out in wait_for_pin: I2C_STAT=%x\n",
-			inw (I2C_STAT));
-	}
-
-	return status;
-}
-- 
1.8.3.1

[U-Boot] [PATCH] i2c, omap1510: remove i2c driver

[Tom Rini]

On Fri, Nov 08, 2013 at 09:38:52AM +0100, Heiko Schocher wrote:

> remove omap1510 i2c driver, as there is no board which uses it
> 
> Signed-off-by: Heiko Schocher <hs@denx.de>
> Cc: Tom Rini <trini@ti.com>
> Cc: Wolfgang Denk <wd@denx.de>

Acked-by: Tom Rini <trini@ti.com>

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20131108/e1dd5966/attachment.pgp>

[U-Boot] i2c, zynq: convert zynq i2c driver to new multibus/multiadapter framework

[Heiko Schocher]

Hello Heiko,

Am 08.11.2013 09:38, schrieb Heiko Schocher:
> - add zync i2c driver to new multibus/multiadpater support
> - adapted all config files, which uses this driver
>
> Signed-off-by: Heiko Schocher<hs@denx.de>
> Cc: Joe Hershberger<joe.hershberger@ni.com>
> Cc: Michal Simek<michal.simek@xilinx.com>
>
> ---
> README                 |  5 +++++
>   drivers/i2c/Makefile   |  2 +-
>   drivers/i2c/zynq_i2c.c | 29 ++++++++++++++++-------------
>   include/configs/zynq.h |  8 ++++----
>   4 files changed, 26 insertions(+), 18 deletions(-)

Applied to u-boot-i2c.git

bye,
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[U-Boot] i2c, omap1510: remove i2c driver

[Heiko Schocher]

Hello Heiko,

Am 08.11.2013 09:38, schrieb Heiko Schocher:
> remove omap1510 i2c driver, as there is no board which uses it
>
> Signed-off-by: Heiko Schocher<hs@denx.de>
> Cc: Tom Rini<trini@ti.com>
> Cc: Wolfgang Denk<wd@denx.de>
> Acked-by: Tom Rini<trini@ti.com>
>
> ---
> drivers/i2c/Makefile       |   1 -
>   drivers/i2c/omap1510_i2c.c | 277 ---------------------------------------------
>   2 files changed, 278 deletions(-)
>   delete mode 100644 drivers/i2c/omap1510_i2c.c

Applied to u-boot-i2c.git

bye,
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany