public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
From: Josh Wu <josh.wu@atmel.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 2/2] ARM: at91: sama5d3: mmc: save enviroment as a fat file (uboot.env)
Date: Wed, 27 Nov 2013 18:26:38 +0800	[thread overview]
Message-ID: <5295C8DE.3020409@atmel.com> (raw)
In-Reply-To: <528F2D1E.20800@atmel.com>

On 11/22/2013 6:08 PM, Bo Shen wrote:
> Hi Josh,
>
> On 11/22/2013 02:58 PM, Josh Wu wrote:
>> This patch will save U-Boot environment as a file: uboot.env, in FAT 
>> partition
>> instead of saving it in raw sector of SD card.
>>
>> Since saving environment in raw sector has risk of corrupting the SD 
>> card and
>> only can use very small size. Save as a FAT file has no above 
>> limitation.
>>
>> Signed-off-by: Josh Wu <josh.wu@atmel.com>
>> ---
>>   include/configs/sama5d3xek.h |   10 +++++++---
>>   1 file changed, 7 insertions(+), 3 deletions(-)
>
> Tested on sama5d31ek board. It doesn't work. Please check it, and also 
> check on at91sam9x5ek board.
>
> Please take the following information as a reference.
> --->8---
> U-Boot 2013.10-00389-gf37e980 (Nov 22 2013 - 17:56:53)
>
> CPU: SAMA5D31
> Crystal frequency:       12 MHz
> CPU clock        :      528 MHz
> Master clock     :      132 MHz
> DRAM:  512 MiB
> NAND:  256 MiB
> MMC:   mci: 0
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 22000000 Hz, block size 512
> reading uboot.env
>
> ** Unable to read "uboot.env" from mmc0:1 **
> Using default environment
>
> In:    serial
> Out:   serial
> Err:   serial
> Net:   macb0
> Warning: failed to set MAC address
> , usb_ether
> Hit any key to stop autoboot:  0
> U-Boot> fat
>   fatinfo fatload fatls fatwrite
> U-Boot> fatls mmc 0
>     20737   boot.bin
>    332916   u-boot.bin
>
> 2 file(s), 0 dir(s)
>
> U-Boot> saveenv
> Saving Environment to FAT...
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 22000000 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 257812 Hz, block size 512
> mci: setting clock 22000000 Hz, block size 512
> writing uboot.env
> done
> U-Boot> fatls mmc 0
>     20737   boot.bin
>    332916   u-boot.bin
>
> 2 file(s), 0 dir(s)
> ---8<---

Oops, this indeed happened in my side too. I will follow on this issue. 
Thanks for the testing.

>
>> diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h
>> index 5a6f0fc..a77ab5f 100644
>> --- a/include/configs/sama5d3xek.h
>> +++ b/include/configs/sama5d3xek.h
>> @@ -196,9 +196,13 @@
>>                   "bootm 0x22000000 - 0x21000000"
>>   #elif CONFIG_SYS_USE_MMC
>>   /* bootstrap + u-boot + env in sd card */
>> -#define CONFIG_ENV_IS_IN_MMC
>> -#define CONFIG_ENV_OFFSET    0x2000
>> -#define CONFIG_ENV_SIZE        0x1000
>> +#define CONFIG_ENV_IS_IN_FAT
>> +#define CONFIG_FAT_WRITE
>> +#define FAT_ENV_INTERFACE    "mmc"
>> +#define FAT_ENV_FILE        "uboot.env"
>> +#define FAT_ENV_DEVICE        0
>> +#define FAT_ENV_PART        1
>> +#define CONFIG_ENV_SIZE        0x4000
>>   #define CONFIG_BOOTCOMMAND    "fatload mmc 0:1 0x21000000 dtb; " \
>>                   "fatload mmc 0:1 0x22000000 uImage; " \
>>                   "bootm 0x22000000 - 0x21000000"
>>
>
> Best Regards,
> Bo Shen

Best Regards,
Josh Wu

      reply	other threads:[~2013-11-27 10:26 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-11-22  6:58 [U-Boot] [PATCH 1/2] ARM: at91: at91sam9x5: mmc: save environment as a FAT file (uboot.env) Josh Wu
2013-11-22  6:58 ` [U-Boot] [PATCH 2/2] ARM: at91: sama5d3: mmc: save enviroment as a fat " Josh Wu
2013-11-22 10:08   ` Bo Shen
2013-11-27 10:26     ` Josh Wu [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=5295C8DE.3020409@atmel.com \
    --to=josh.wu@atmel.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox