[U-Boot] [PATCH v2 2/4] arm: exynos: pinmux: Add sdmmc4 gpio configuration

[Piotr Wilczek <p.wilczek@samsung.com>]

Dear Beomho Seo,

On 03/14/2014 09:33 AM, Beomho Seo wrote:
> For use dwmmc controller at exynos4, add SDMMC gpio configuration.
> In case SDMMC2, do not use 8bit mode at exynos4.
>
> Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
> Cc: Lukasz Majewski <l.majewski@samsung.com>
> Cc: Piotr Wilczek <p.wilczek@samsung.com>
> Cc: Minkyu Kang <mk7.kang@samsung.com>
> ---
> Changes for v2:
> - Fixed value initialise.
> - Comment add in function.
>
>   arch/arm/cpu/armv7/exynos/pinmux.c |   19 +++++++++++++++----
>   1 file changed, 15 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm/cpu/armv7/exynos/pinmux.c b/arch/arm/cpu/armv7/exynos/pinmux.c
> index 9edb475..3dce5d2 100644
> --- a/arch/arm/cpu/armv7/exynos/pinmux.c
> +++ b/arch/arm/cpu/armv7/exynos/pinmux.c
> @@ -632,16 +632,26 @@ static int exynos4_mmc_config(int peripheral, int flags)
>   	struct exynos4_gpio_part2 *gpio2 =
>   		(struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2();
>   	struct s5p_gpio_bank *bank, *bank_ext;
> +	unsigned int  func, func_ext;
>   	int i;
>
>   	switch (peripheral) {
>   	case PERIPH_ID_SDMMC0:
>   		bank = &gpio2->k0;
>   		bank_ext = &gpio2->k1;
> +		func = GPIO_FUNC(0x2);
> +		func_ext = GPIO_FUNC(0x3);
>   		break;
>   	case PERIPH_ID_SDMMC2:
>   		bank = &gpio2->k2;
> -		bank_ext = &gpio2->k3;
that causes warning 'bank_ext' may be used uninitialized in this function

> +		func = GPIO_FUNC(0x2);
> +		func_ext = 0;
> +		break;
> +	case PERIPH_ID_SDMMC4:
> +		bank = &gpio2->k0;
> +		bank_ext = &gpio2->k1;
> +		func = GPIO_FUNC(0x3);
> +		func_ext = GPIO_FUNC(0x4);
>   		break;
>   	default:
>   		return -1;
> @@ -649,13 +659,14 @@ static int exynos4_mmc_config(int peripheral, int flags)
>   	for (i = 0; i < 7; i++) {
>   		if (i == 2)
>   			continue;
> -		s5p_gpio_cfg_pin(bank, i,  GPIO_FUNC(0x2));
> +		s5p_gpio_cfg_pin(bank, i,  func);
>   		s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE);
>   		s5p_gpio_set_drv(bank, i, GPIO_DRV_4X);
>   	}
> +	/* SDMMC do not use 8bit mode at exynos4 */
>   	if (flags & PINMUX_FLAG_8BIT_MODE) {
>   		for (i = 3; i < 7; i++) {
> -			s5p_gpio_cfg_pin(bank_ext, i,  GPIO_FUNC(0x3));
> +			s5p_gpio_cfg_pin(bank_ext, i,  func_ext);
>   			s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_NONE);
>   			s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X);
>   		}
> @@ -722,10 +733,10 @@ static int exynos4_pinmux_config(int peripheral, int flags)
>   		break;
>   	case PERIPH_ID_SDMMC0:
>   	case PERIPH_ID_SDMMC2:
> +	case PERIPH_ID_SDMMC4:
>   		return exynos4_mmc_config(peripheral, flags);
>   	case PERIPH_ID_SDMMC1:
>   	case PERIPH_ID_SDMMC3:
> -	case PERIPH_ID_SDMMC4:
>   		debug("SDMMC device %d not implemented\n", peripheral);
>   		return -1;
>   	default:
>

Best regards,
Piotr Wilczek