[U-Boot] [PATCH v8 1/2] S5P: Exynos: Add GPIO pin numbering and rename definitions

[Przemyslaw Marczak <p.marczak@samsung.com>]

Hello Akshay,
  04/16/2014 07:32 AM, Akshay Saraswat wrote:
> This patch includes following changes :
> * Adds gpio pin numbering support for EXYNOS SOCs.
>    To have consistent 0..n-1 GPIO numbering the banks are divided
>    into different parts where ever they have holes in them.
>
> * Rename GPIO definitions from GPIO_... to S5P_GPIO_...
>    These changes were done to enable cmd_gpio for EXYNOS and
>    cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
>    getting a error during compilation.
>
> * Adds support for name to gpio conversion in s5p_gpio to enable
>    gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
>    to decode the input gpio name to gpio number.
>    Example: SMDK5420 # gpio set gpa00
>
> Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
> Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
> ---
>   arch/arm/cpu/armv7/exynos/pinmux.c       |  403 +++----
>   arch/arm/include/asm/arch-exynos/cpu.h   |   17 +-
>   arch/arm/include/asm/arch-exynos/gpio.h  | 1778 +++++++++++++++++++++++++-----
>   arch/arm/include/asm/arch-s5pc1xx/gpio.h |  941 +++++++++++++---
>   board/samsung/arndale/arndale.c          |   11 +-
>   board/samsung/goni/goni.c                |   26 +-
>   board/samsung/smdk5250/exynos5-dt.c      |   20 +-
>   board/samsung/smdk5250/smdk5250.c        |   19 +-
>   board/samsung/smdk5420/smdk5420.c        |   15 +-
>   board/samsung/smdkc100/smdkc100.c        |    5 +-
>   board/samsung/smdkv310/smdkv310.c        |   17 +-
>   board/samsung/trats/trats.c              |   39 +-
>   board/samsung/trats2/trats2.c            |   74 +-
>   board/samsung/universal_c210/universal.c |   51 +-
>   drivers/gpio/s5p_gpio.c                  |  194 +++-
>   15 files changed, 2779 insertions(+), 831 deletions(-)
>
>

You introduced new method for gpio numbering and I don't know why are 
you using macro like this:
"exynos_gpio_get(2, EXYNOS4X12_GPIO_X33)"
and also new style like only "EXYNOS4X12_GPIO_X33".

Those are two different numbers and can't be given to s5p_gpio driver 
which interprets only new gpio numbering method.
This code can't work properly.

Please remove old macros and use only proper gpio enum in boards config 
files.
We don't need any "get" macro if all gpio numbers are defined explicitly.

You should also modify proper dts files in arch/arm/dts/* .

I tested your changes with enums only and after change proper dts file 
for trats2 there is still data abort.
So this means that probably enums are not mapped correctly to proper 
gpio bank addresses.

Do you have an documentation for Exynos4 socs?

I think that this should be checked again with documentation and 
compiled next to the current code which is simple and just works.

There are also some warnings when checking by checkpatch script.

Thanks
-- 
Przemyslaw Marczak
Samsung R&D Institute Poland
Samsung Electronics
p.marczak at samsung.com