[U-Boot] [PATCH v2 2/3] arm:at91: enable ROM loadable atmel image

["Andreas Bießmann" <andreas.devel@googlemail.com>]

Hi Bo,

On 05/19/2014 05:13 AM, Bo Shen wrote:
> On 05/16/2014 05:59 PM, Andreas Bie?mann wrote:
>> For sama5d3xek we need to modify the SPL image for correct detection
>> by ROM
>> code.
>>
>> Signed-off-by: Andreas Bie?mann <andreas.devel@googlemail.com>
>> ---
>>
>> Changes in v2:
>> * add -n switch to mkimage for PMECC type NAND and CONFIG_SYS_NANDFLASH
>>
>>   arch/arm/cpu/armv7/at91/config.mk |   10 ++++++++++
>>   doc/README.atmel_pmecc            |   30 ++++++++++++++++++++++++++++++
>>   spl/Makefile                      |   18 ++++++++++++++++++
>>   3 files changed, 58 insertions(+)
>>   create mode 100644 arch/arm/cpu/armv7/at91/config.mk
>>

>> diff --git a/doc/README.atmel_pmecc b/doc/README.atmel_pmecc
>> index cf8373b..5a93123 100644
>> --- a/doc/README.atmel_pmecc
>> +++ b/doc/README.atmel_pmecc
>> @@ -27,3 +27,33 @@ Take AT91SAM9X5EK as an example, the board
>> definition file likes:
>>   #define CONFIG_ATMEL_NAND_HW_PMECC    1
>>   #define CONFIG_PMECC_CAP        2
>>   #define CONFIG_PMECC_SECTOR_SIZE    512
>> +
>> +How to enable PMECC header for direct programmable boot.bin
>> +-----------------------------------------------------------
>> +2014-05-15 Andreas Bie?mann <andreas.devel@googlemail.com>
>> +
>> +The usual way to program SPL into NAND flash is to use the SAM-BA
>> Atmel tool.
>> +This however is often not usable when doing field updates. To be able to
>> +program a SPL binary into NAND flash we need to add the PMECC header
>> to the
>> +binary before. Chapter '12.4.4.1 NAND Flash Boot: NAND Flash
>> Detection' in
>> +sama5d3 SoC spec (as of 03. April 2014). We have a new image type
>> added to
>> +mkimage to generate this PMECC header and integrated into the build
>> process of
>> +SPL.
>> +The required parameters in board configuration header are as follows:
>> +
>> +This example is working for sama5d3xek:
>> +
>> +#define CONFIG_SPL_AT91_HEADER_USE_PMECC    1
>> +#define CONFIG_SPL_AT91_HEADER_SECTOR_PER_PAGE    4
>> +#define CONFIG_SPL_AT91_HEADER_SECTOR_SIZE    CONFIG_PMECC_SECTOR_SIZE
>> +#define CONFIG_SPL_AT91_HEADER_SPARE_SIZE    64
>> +#define CONFIG_SPL_AT91_HEADER_ECC_BITS        CONFIG_PMECC_CAP
>> +#define CONFIG_SPL_AT91_HEADER_ECC_OFFSET    36
> 
> Just a nitpick here:
> 
> Can we take this parameter from the existing definition while not use
> new definition? Or else, if the header using different parameter with
> what u-boot nand driver use, then if flash through u-boot, it won't boot.

I used the two parameters I found, sorry the rest isn't defiend anywhere
(or I can't find). Can you give me pointers to the other parameters?

Best regards

Andreas Bie?mann