* [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support
@ 2014-05-21 2:42 Josh Wu
2014-05-21 2:42 ` [U-Boot] [PATCH v2 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support Josh Wu
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Josh Wu @ 2014-05-21 2:42 UTC (permalink / raw)
To: u-boot
Also we enable the mmc command in configuration file.
As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
---
v1 -> v2:
1. refined the comment for the pins.
2. remove detected pin initialization.
3. move the mci initialization code to devices.c
4. remove useless header file: mmc.h
.../cpu/arm926ejs/at91/at91sam9m10g45_devices.c | 17 +++++++++++++++++
board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 10 ++++++++++
include/configs/at91sam9m10g45ek.h | 15 ++++++++++++++-
3 files changed, 41 insertions(+), 1 deletion(-)
diff --git a/arch/arm/cpu/arm926ejs/at91/at91sam9m10g45_devices.c b/arch/arm/cpu/arm926ejs/at91/at91sam9m10g45_devices.c
index 7d7725c..0e6c0da 100644
--- a/arch/arm/cpu/arm926ejs/at91/at91sam9m10g45_devices.c
+++ b/arch/arm/cpu/arm926ejs/at91/at91sam9m10g45_devices.c
@@ -165,3 +165,20 @@ void at91_macb_hw_init(void)
#endif
}
#endif
+
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+void at91_mci_hw_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+
+ at91_set_a_periph(AT91_PIO_PORTA, 0, 0); /* MCI0 CLK */
+ at91_set_a_periph(AT91_PIO_PORTA, 1, 0); /* MCI0 CDA */
+ at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* MCI0 DA0 */
+ at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* MCI0 DA1 */
+ at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* MCI0 DA2 */
+ at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* MCI0 DA3 */
+
+ /* Enable clock */
+ writel(1 << ATMEL_ID_MCI0, &pmc->pcer);
+}
+#endif
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
index b7e2efd..5788116 100644
--- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
+++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
@@ -16,6 +16,7 @@
#include <asm/arch/clk.h>
#include <lcd.h>
#include <atmel_lcdc.h>
+#include <atmel_mci.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
@@ -217,6 +218,15 @@ void lcd_show_board_info(void)
#endif /* CONFIG_LCD_INFO */
#endif
+#ifdef CONFIG_GENERIC_ATMEL_MCI
+int board_mmc_init(bd_t *bis)
+{
+ at91_mci_hw_init();
+
+ return atmel_mci_init((void *)ATMEL_BASE_MCI0);
+}
+#endif
+
int board_early_init_f(void)
{
at91_seriald_hw_init();
diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
index ccfda71..df277e7 100644
--- a/include/configs/at91sam9m10g45ek.h
+++ b/include/configs/at91sam9m10g45ek.h
@@ -115,6 +115,20 @@
#endif
+/* MMC */
+#define CONFIG_CMD_MMC
+
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#endif
+
+#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
/* Ethernet */
#define CONFIG_MACB
#define CONFIG_RMII
@@ -126,7 +140,6 @@
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
-#define CONFIG_DOS_PARTITION
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
--
1.7.9.5
^ permalink raw reply related [flat|nested] 6+ messages in thread* [U-Boot] [PATCH v2 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support
2014-05-21 2:42 [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support Josh Wu
@ 2014-05-21 2:42 ` Josh Wu
2014-05-22 1:35 ` Bo Shen
2014-05-26 22:13 ` [U-Boot] [U-Boot, v2, " Andreas Bießmann
2014-05-22 1:35 ` [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support Bo Shen
2014-05-26 22:13 ` [U-Boot] [U-Boot,v2,1/2] " Andreas Bießmann
2 siblings, 2 replies; 6+ messages in thread
From: Josh Wu @ 2014-05-21 2:42 UTC (permalink / raw)
To: u-boot
In this configuration the environment will save in file: uboot.env of
mmc card.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
---
v1 -> v2:
1. remove mem=128m and roottype in bootargs.
2. default boot command use zImage instead of uImage.
boards.cfg | 1 +
include/configs/at91sam9m10g45ek.h | 19 +++++++++++++++++++
2 files changed, 20 insertions(+)
diff --git a/boards.cfg b/boards.cfg
index 3a59686..9f7cfd8 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -102,6 +102,7 @@ Active arm arm926ejs at91 atmel at91sam9263ek
Active arm arm926ejs at91 atmel at91sam9263ek at91sam9263ek_norflash at91sam9263ek:AT91SAM9263,SYS_USE_NORFLASH Stelian Pop <stelian@popies.net>
Active arm arm926ejs at91 atmel at91sam9263ek at91sam9263ek_norflash_boot at91sam9263ek:AT91SAM9263,SYS_USE_BOOT_NORFLASH Stelian Pop <stelian@popies.net>
Active arm arm926ejs at91 atmel at91sam9m10g45ek at91sam9m10g45ek_nandflash at91sam9m10g45ek:AT91SAM9M10G45,SYS_USE_NANDFLASH Bo Shen<voice.shen@atmel.com>
+Active arm arm926ejs at91 atmel at91sam9m10g45ek at91sam9m10g45ek_mmc at91sam9m10g45ek:AT91SAM9M10G45,SYS_USE_MMC Bo Shen<voice.shen@atmel.com>
Active arm arm926ejs at91 atmel at91sam9n12ek at91sam9n12ek_mmc at91sam9n12ek:AT91SAM9N12,SYS_USE_MMC Josh Wu <josh.wu@atmel.com>
Active arm arm926ejs at91 atmel at91sam9n12ek at91sam9n12ek_nandflash at91sam9n12ek:AT91SAM9N12,SYS_USE_NANDFLASH Josh Wu <josh.wu@atmel.com>
Active arm arm926ejs at91 atmel at91sam9n12ek at91sam9n12ek_spiflash at91sam9n12ek:AT91SAM9N12,SYS_USE_SPIFLASH Josh Wu <josh.wu@atmel.com>
diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
index df277e7..cab3bb5 100644
--- a/include/configs/at91sam9m10g45ek.h
+++ b/include/configs/at91sam9m10g45ek.h
@@ -147,6 +147,7 @@
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x23e00000
+#ifdef CONFIG_SYS_USE_NANDFLASH
/* bootstrap + u-boot + env in nandflash */
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0xc0000
@@ -162,6 +163,24 @@
"256k(env),256k(env_redundant),256k(spare)," \
"512k(dtb),6M(kernel)ro,-(rootfs) " \
"root=/dev/mtdblock7 rw rootfstype=jffs2"
+#elif CONFIG_SYS_USE_MMC
+/* bootstrap + u-boot + env + linux in mmc */
+#define FAT_ENV_INTERFACE "mmc"
+#define FAT_ENV_DEVICE 0
+#define FAT_ENV_PART 1
+#define FAT_ENV_FILE "uboot.env"
+#define CONFIG_ENV_IS_IN_FAT
+#define CONFIG_FAT_WRITE
+#define CONFIG_ENV_SIZE 0x4000
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
+ "mtdparts=atmel_nand:" \
+ "8M(bootstrap/uboot/kernel)ro,-(rootfs) " \
+ "root=/dev/mmcblk0p2 rw rootwait"
+#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x71000000 dtb; " \
+ "fatload mmc 0:1 0x72000000 zImage; " \
+ "bootz 0x72000000 - 0x71000000"
+#endif
#define CONFIG_BAUDRATE 115200
--
1.7.9.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH v2 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support
2014-05-21 2:42 ` [U-Boot] [PATCH v2 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support Josh Wu
@ 2014-05-22 1:35 ` Bo Shen
2014-05-26 22:13 ` [U-Boot] [U-Boot, v2, " Andreas Bießmann
1 sibling, 0 replies; 6+ messages in thread
From: Bo Shen @ 2014-05-22 1:35 UTC (permalink / raw)
To: u-boot
Hi Josh,
On 05/21/2014 10:42 AM, Josh Wu wrote:
> In this configuration the environment will save in file: uboot.env of
> mmc card.
>
> Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
> ---
> v1 -> v2:
> 1. remove mem=128m and roottype in bootargs.
> 2. default boot command use zImage instead of uImage.
>
> boards.cfg | 1 +
> include/configs/at91sam9m10g45ek.h | 19 +++++++++++++++++++
> 2 files changed, 20 insertions(+)
>
> diff --git a/boards.cfg b/boards.cfg
> index 3a59686..9f7cfd8 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -102,6 +102,7 @@ Active arm arm926ejs at91 atmel at91sam9263ek
> Active arm arm926ejs at91 atmel at91sam9263ek at91sam9263ek_norflash at91sam9263ek:AT91SAM9263,SYS_USE_NORFLASH Stelian Pop <stelian@popies.net>
> Active arm arm926ejs at91 atmel at91sam9263ek at91sam9263ek_norflash_boot at91sam9263ek:AT91SAM9263,SYS_USE_BOOT_NORFLASH Stelian Pop <stelian@popies.net>
> Active arm arm926ejs at91 atmel at91sam9m10g45ek at91sam9m10g45ek_nandflash at91sam9m10g45ek:AT91SAM9M10G45,SYS_USE_NANDFLASH Bo Shen<voice.shen@atmel.com>
> +Active arm arm926ejs at91 atmel at91sam9m10g45ek at91sam9m10g45ek_mmc at91sam9m10g45ek:AT91SAM9M10G45,SYS_USE_MMC Bo Shen<voice.shen@atmel.com>
> Active arm arm926ejs at91 atmel at91sam9n12ek at91sam9n12ek_mmc at91sam9n12ek:AT91SAM9N12,SYS_USE_MMC Josh Wu <josh.wu@atmel.com>
> Active arm arm926ejs at91 atmel at91sam9n12ek at91sam9n12ek_nandflash at91sam9n12ek:AT91SAM9N12,SYS_USE_NANDFLASH Josh Wu <josh.wu@atmel.com>
> Active arm arm926ejs at91 atmel at91sam9n12ek at91sam9n12ek_spiflash at91sam9n12ek:AT91SAM9N12,SYS_USE_SPIFLASH Josh Wu <josh.wu@atmel.com>
> diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
> index df277e7..cab3bb5 100644
> --- a/include/configs/at91sam9m10g45ek.h
> +++ b/include/configs/at91sam9m10g45ek.h
> @@ -147,6 +147,7 @@
> #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
> #define CONFIG_SYS_MEMTEST_END 0x23e00000
>
> +#ifdef CONFIG_SYS_USE_NANDFLASH
> /* bootstrap + u-boot + env in nandflash */
> #define CONFIG_ENV_IS_IN_NAND
> #define CONFIG_ENV_OFFSET 0xc0000
> @@ -162,6 +163,24 @@
> "256k(env),256k(env_redundant),256k(spare)," \
> "512k(dtb),6M(kernel)ro,-(rootfs) " \
> "root=/dev/mtdblock7 rw rootfstype=jffs2"
> +#elif CONFIG_SYS_USE_MMC
> +/* bootstrap + u-boot + env + linux in mmc */
> +#define FAT_ENV_INTERFACE "mmc"
> +#define FAT_ENV_DEVICE 0
> +#define FAT_ENV_PART 1
> +#define FAT_ENV_FILE "uboot.env"
> +#define CONFIG_ENV_IS_IN_FAT
> +#define CONFIG_FAT_WRITE
> +#define CONFIG_ENV_SIZE 0x4000
> +
> +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
> + "mtdparts=atmel_nand:" \
> + "8M(bootstrap/uboot/kernel)ro,-(rootfs) " \
> + "root=/dev/mmcblk0p2 rw rootwait"
> +#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x71000000 dtb; " \
> + "fatload mmc 0:1 0x72000000 zImage; " \
> + "bootz 0x72000000 - 0x71000000"
> +#endif
>
> #define CONFIG_BAUDRATE 115200
>
>
Best Regards,
Bo Shen
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] [U-Boot, v2, 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support
2014-05-21 2:42 ` [U-Boot] [PATCH v2 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support Josh Wu
2014-05-22 1:35 ` Bo Shen
@ 2014-05-26 22:13 ` Andreas Bießmann
1 sibling, 0 replies; 6+ messages in thread
From: Andreas Bießmann @ 2014-05-26 22:13 UTC (permalink / raw)
To: u-boot
Dear Josh Wu,
Josh Wu <Josh.wu@atmel.com> writes:
>In this configuration the environment will save in file: uboot.env of
>mmc card.
>
>Signed-off-by: Josh Wu <josh.wu@atmel.com>
>
>---
>v1 -> v2:
> 1. remove mem=128m and roottype in bootargs.
> 2. default boot command use zImage instead of uImage.
>
> boards.cfg | 1 +
> include/configs/at91sam9m10g45ek.h | 19 +++++++++++++++++++
> 2 files changed, 20 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support
2014-05-21 2:42 [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support Josh Wu
2014-05-21 2:42 ` [U-Boot] [PATCH v2 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support Josh Wu
@ 2014-05-22 1:35 ` Bo Shen
2014-05-26 22:13 ` [U-Boot] [U-Boot,v2,1/2] " Andreas Bießmann
2 siblings, 0 replies; 6+ messages in thread
From: Bo Shen @ 2014-05-22 1:35 UTC (permalink / raw)
To: u-boot
Hi Josh,
On 05/21/2014 10:42 AM, Josh Wu wrote:
> Also we enable the mmc command in configuration file.
>
> As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
> so remove the redundant CONFIG_DOS_PARTITION definition.
>
> Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
> ---
> v1 -> v2:
> 1. refined the comment for the pins.
> 2. remove detected pin initialization.
> 3. move the mci initialization code to devices.c
> 4. remove useless header file: mmc.h
>
> .../cpu/arm926ejs/at91/at91sam9m10g45_devices.c | 17 +++++++++++++++++
> board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 10 ++++++++++
> include/configs/at91sam9m10g45ek.h | 15 ++++++++++++++-
> 3 files changed, 41 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/cpu/arm926ejs/at91/at91sam9m10g45_devices.c b/arch/arm/cpu/arm926ejs/at91/at91sam9m10g45_devices.c
> index 7d7725c..0e6c0da 100644
> --- a/arch/arm/cpu/arm926ejs/at91/at91sam9m10g45_devices.c
> +++ b/arch/arm/cpu/arm926ejs/at91/at91sam9m10g45_devices.c
> @@ -165,3 +165,20 @@ void at91_macb_hw_init(void)
> #endif
> }
> #endif
> +
> +#ifdef CONFIG_GENERIC_ATMEL_MCI
> +void at91_mci_hw_init(void)
> +{
> + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
> +
> + at91_set_a_periph(AT91_PIO_PORTA, 0, 0); /* MCI0 CLK */
> + at91_set_a_periph(AT91_PIO_PORTA, 1, 0); /* MCI0 CDA */
> + at91_set_a_periph(AT91_PIO_PORTA, 2, 0); /* MCI0 DA0 */
> + at91_set_a_periph(AT91_PIO_PORTA, 3, 0); /* MCI0 DA1 */
> + at91_set_a_periph(AT91_PIO_PORTA, 4, 0); /* MCI0 DA2 */
> + at91_set_a_periph(AT91_PIO_PORTA, 5, 0); /* MCI0 DA3 */
> +
> + /* Enable clock */
> + writel(1 << ATMEL_ID_MCI0, &pmc->pcer);
> +}
> +#endif
> diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> index b7e2efd..5788116 100644
> --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> @@ -16,6 +16,7 @@
> #include <asm/arch/clk.h>
> #include <lcd.h>
> #include <atmel_lcdc.h>
> +#include <atmel_mci.h>
> #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
> #include <net.h>
> #endif
> @@ -217,6 +218,15 @@ void lcd_show_board_info(void)
> #endif /* CONFIG_LCD_INFO */
> #endif
>
> +#ifdef CONFIG_GENERIC_ATMEL_MCI
> +int board_mmc_init(bd_t *bis)
> +{
> + at91_mci_hw_init();
> +
> + return atmel_mci_init((void *)ATMEL_BASE_MCI0);
> +}
> +#endif
> +
> int board_early_init_f(void)
> {
> at91_seriald_hw_init();
> diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
> index ccfda71..df277e7 100644
> --- a/include/configs/at91sam9m10g45ek.h
> +++ b/include/configs/at91sam9m10g45ek.h
> @@ -115,6 +115,20 @@
>
> #endif
>
> +/* MMC */
> +#define CONFIG_CMD_MMC
> +
> +#ifdef CONFIG_CMD_MMC
> +#define CONFIG_MMC
> +#define CONFIG_GENERIC_MMC
> +#define CONFIG_GENERIC_ATMEL_MCI
> +#endif
> +
> +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
> +#define CONFIG_CMD_FAT
> +#define CONFIG_DOS_PARTITION
> +#endif
> +
> /* Ethernet */
> #define CONFIG_MACB
> #define CONFIG_RMII
> @@ -126,7 +140,6 @@
> #define CONFIG_USB_EHCI
> #define CONFIG_USB_EHCI_ATMEL
> #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
> -#define CONFIG_DOS_PARTITION
> #define CONFIG_USB_STORAGE
>
> #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
>
Best Regards,
Bo Shen
^ permalink raw reply [flat|nested] 6+ messages in thread* [U-Boot] [U-Boot,v2,1/2] ARM: at91sam9m10g45ek: enable mci0 support
2014-05-21 2:42 [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support Josh Wu
2014-05-21 2:42 ` [U-Boot] [PATCH v2 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support Josh Wu
2014-05-22 1:35 ` [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support Bo Shen
@ 2014-05-26 22:13 ` Andreas Bießmann
2 siblings, 0 replies; 6+ messages in thread
From: Andreas Bießmann @ 2014-05-26 22:13 UTC (permalink / raw)
To: u-boot
Dear Josh Wu,
Josh Wu <Josh.wu@atmel.com> writes:
>Also we enable the mmc command in configuration file.
>
>As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
>so remove the redundant CONFIG_DOS_PARTITION definition.
>
>Signed-off-by: Josh Wu <josh.wu@atmel.com>
>
>---
>v1 -> v2:
> 1. refined the comment for the pins.
> 2. remove detected pin initialization.
> 3. move the mci initialization code to devices.c
> 4. remove useless header file: mmc.h
>
> .../cpu/arm926ejs/at91/at91sam9m10g45_devices.c | 17 +++++++++++++++++
> board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 10 ++++++++++
> include/configs/at91sam9m10g45ek.h | 15 ++++++++++++++-
> 3 files changed, 41 insertions(+), 1 deletion(-)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2014-05-26 22:13 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-05-21 2:42 [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support Josh Wu
2014-05-21 2:42 ` [U-Boot] [PATCH v2 2/2] ARM: at91sam9m10g45ek: add mmc environment configuration support Josh Wu
2014-05-22 1:35 ` Bo Shen
2014-05-26 22:13 ` [U-Boot] [U-Boot, v2, " Andreas Bießmann
2014-05-22 1:35 ` [U-Boot] [PATCH v2 1/2] ARM: at91sam9m10g45ek: enable mci0 support Bo Shen
2014-05-26 22:13 ` [U-Boot] [U-Boot,v2,1/2] " Andreas Bießmann
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox