public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
From: "Jörg Krause" <jkrause@posteo.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] usb: ci_udc: fix interaction with CONFIG_USB_ETH_CDC
Date: Sat, 28 Jun 2014 22:37:35 +0200	[thread overview]
Message-ID: <53AF278F.80403@posteo.de> (raw)
In-Reply-To: <53AE1BA9.9000401@posteo.de>

On 06/28/2014 09:59 PM, Marek Vasut wrote:

> I would actually be really glad if you could test plain u-boot-usb/master and
> see if your USB problem is present there. Also, it would be really nice to
> isolate the sequence of commands which triggers the bug, so we have a proper
> reproducible testcase.
>
> Anyway, this thread is not a place where I would like to discuss this. This
> should be discussed in the "original" thread, that is:
>
> Subj: [PATCH] usb: ci_udc: fix interaction with CONFIG_USB_ETH_CDC

I cloned u-boot-usb/master and tested it. I am running "tftpd 
rootfs.ubifs" several times. Here is the log (I shortened the loading 
process bar):

    HTLLCLLC

    U-Boot 2014.07-rc3-g18e0313 (Jun 28 2014 - 22:17:52)

    CPU:   Freescale i.MX28 rev1.2 at 454 MHz
    BOOT:  NAND, 3V3
    DRAM:  64 MiB
    NAND:  128 MiB
    In:    serial
    Out:   serial
    Err:   serial
    Net:   usb_ether [PRIME]
    Hit any key to stop autoboot:  0
    => tftp rootfs.ubifs
    using ci_udc, OUT ep- IN ep- STATUS ep-
    MAC 00:19:b8:00:00:02
    HOST MAC 00:19:b8:00:00:01
    high speed config #1: 2 mA, Ethernet Gadget, using CDC Ethernet
    USB network up!
    Using usb_ether device
    TFTP from server 10.0.0.1; our IP address is 10.0.0.2
    Filename 'rootfs.ubifs'.
    Load address: 0x40008000
    Loading: [snip]
      ##############################################################T ###
          [snip]
          1.7 MiB/s
    done
    Bytes transferred = 13205504 (c98000 hex)
    => tftp rootfs.ubifs
    using ci_udc, OUT ep- IN ep- STATUS ep-
    MAC 00:19:b8:00:00:02
    HOST MAC 00:19:b8:00:00:01
    high speed config #1: 2 mA, Ethernet Gadget, using CDC Ethernet
    USB network up!
    Using usb_ether device
    TFTP from server 10.0.0.1; our IP address is 10.0.0.2
    Filename 'rootfs.ubifs'.
    Load address: 0x40008000
    Loading:
    #################################################################
          [snip]
          5.6 MiB/s
    done
    Bytes transferred = 13205504 (c98000 hex)
    => tftp rootfs.ubifs
    using ci_udc, OUT ep- IN ep- STATUS ep-
    MAC 00:19:b8:00:00:02
    HOST MAC 00:19:b8:00:00:01
    high speed config #1: 2 mA, Ethernet Gadget, using CDC Ethernet
    USB network up!
    Using usb_ether device
    TFTP from server 10.0.0.1; our IP address is 10.0.0.2
    Filename 'rootfs.ubifs'.
    Load address: 0x40008000
    Loading:
    #################################################################
          [snip]
          5.6 MiB/s
    done
    Bytes transferred = 13205504 (c98000 hex)
    => tftp rootfs.ubifs
    using ci_udc, OUT ep- IN ep- STATUS ep-
    MAC 00:19:b8:00:00:02
    HOST MAC 00:19:b8:00:00:01
    high speed config #1: 2 mA, Ethernet Gadget, using CDC Ethernet
    ERROR: The remote end did not respond in time.
    at drivers/usb/gadget/ether.c:2388/usb_eth_init()
    =>

The error always appears after calling tftp the third time! The first 
two runs work fine, but the third one always fails. I run this test 
about 20 times.

Best regards
J?rg Krause

  reply	other threads:[~2014-06-28 20:37 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-06-23 18:02 [U-Boot] [PATCH] usb: ci_udc: fix interaction with CONFIG_USB_ETH_CDC Stephen Warren
2014-06-23 19:03 ` Eric Nelson
2014-06-25 13:51 ` Marek Vasut
2014-06-25 16:06   ` Stephen Warren
2014-06-27 21:37     ` Jörg Krause
2014-06-27 21:52       ` Jörg Krause
2014-06-27 21:56         ` Stephen Warren
2014-06-27 23:27           ` Jörg Krause
2014-06-27 21:55       ` Stephen Warren
2014-06-27 23:16         ` Jörg Krause
2014-06-27 23:37           ` Stephen Warren
2014-06-28  0:09             ` Jörg Krause
2014-06-28  1:34             ` Jörg Krause
2014-06-28 20:37               ` Jörg Krause [this message]
2014-06-28 20:45                 ` Marek Vasut
2014-06-28 20:53                   ` Jörg Krause
2014-06-29 20:33                     ` Jörg Krause
2014-06-30  9:37                       ` Marek Vasut
2014-06-30 13:34                         ` Jörg Krause
2014-06-30 16:02               ` Stephen Warren
2014-06-30 19:55                 ` Stephen Warren
2014-06-30 22:44                   ` Jörg Krause
2014-06-30 22:51                     ` Stephen Warren
2014-06-30 23:17                       ` Jörg Krause
2014-06-30 23:56                         ` Marek Vasut
2014-06-30 20:55                 ` Jörg Krause
2014-06-30 21:15                   ` Marek Vasut
2014-06-30 21:43                     ` Jörg Krause
2014-06-30 21:50                       ` Marek Vasut
2014-06-25 20:20 ` Marek Vasut

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=53AF278F.80403@posteo.de \
    --to=jkrause@posteo.de \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox