[U-Boot] [PATCH 12/18] arm: mx6: add support for Compulab cm-fx6 CoM

[Nikita Kiryanov <nikita@compulab.co.il>]

On 04/08/14 07:45, Tim Harvey wrote:
> On Sun, Aug 3, 2014 at 12:34 AM, Nikita Kiryanov <nikita@compulab.co.il> wrote:
>> Add initial support for Compulab CM-FX6 CoM.
>> Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.
>>
> <snip>
>> +
>> +static void spl_mx6s_dram_init(enum ddr_config dram_config, int reset)
>> +{
>> +       struct mx6_mmdc_calibration calib;
>> +       struct mx6_ddr_sysinfo sysinfo;
>> +       struct mx6_ddr3_cfg ddr3_cfg;
>> +
>> +       if (reset)
>> +               ((struct mmdc_p_regs *)MX6_MMDC_P0_MDCTL)->mdmisc = 2;
>> +
>> +       calib.p0_mpwldectrl0    = 0x005B0061;
>> +       calib.p0_mpwldectrl1    = 0x004F0055;
>> +       calib.p0_mpdgctrl0      = 0x0314030C;
>> +       calib.p0_mpdgctrl1      = 0x025C0268;
>> +       calib.p0_mprddlctl      = 0x42464646;
>> +       calib.p0_mpwrdlctl      = 0x36322C34;
>> +       ddr3_cfg.mem_speed      = 800;
>> +       ddr3_cfg.density        = 4;
>> +       ddr3_cfg.rowaddr        = 14;
>> +       ddr3_cfg.coladdr        = 10;
>> +       ddr3_cfg.pagesz         = 2;
>> +       ddr3_cfg.trcd           = 1800;
>> +       ddr3_cfg.trcmin         = 5200;
>> +       ddr3_cfg.trasmin        = 3600;
>> +       ddr3_cfg.SRT            = 0;
>> +       sysinfo.cs1_mirror      = 1;
>> +       sysinfo.cs_density      = 16;
>> +       sysinfo.bi_on           = 1;
>> +       sysinfo.rtt_nom         = 1;
>> +       sysinfo.rtt_wr          = 0;
>> +       sysinfo.ralat           = 5;
>> +       sysinfo.walat           = 1;
>> +       sysinfo.mif3_mode       = 3;
>> +       sysinfo.rst_to_cke      = 0x23;
>> +       sysinfo.sde_to_rst      = 0x10;
>> +       switch (dram_config) {
>> +       case DDR_16BIT_256MB:
>> +               sysinfo.dsize = 0;
>> +               sysinfo.ncs = 1;
>> +               break;
>> +       case DDR_32BIT_512MB:
>> +               sysinfo.dsize = 1;
>> +               sysinfo.ncs = 1;
>> +               break;
>> +       case DDR_32BIT_1GB:
>> +               sysinfo.dsize = 1;
>> +               sysinfo.ncs = 2;
>> +               break;
>> +       default:
>> +               puts("Tried to setup invalid DDR configuration\n");
>> +               hang();
>> +       }
>> +
>> +       mx6_dram_cfg(&sysinfo, &calib, &ddr3_cfg);
>> +       udelay(100);
>> +}
>
> Nikita,
>
> I'm curious why you add an extra udelay(100) here? There is an
> mdelay(1) before the return of mx6_dram_cfg() to wait for auto-ZQ
> calibration to complete (I never found a way to determine when it was
> complete via registers).

Yes you're right. This udelay can probably be removed (unless I catch
the board misbehaving during multiple resets).

>
> Regards,
>
> Tim
>