From mboxrd@z Thu Jan  1 00:00:00 1970
From: Nikita Kiryanov <nikita@compulab.co.il>
Date: Tue, 19 Aug 2014 17:49:49 +0300
Subject: [U-Boot] [PATCH V2 15/18] arm: mx6: cm_fx6: add usb support
In-Reply-To: <53EB7080.2080205@compulab.co.il>
References: <1407690780-19645-1-git-send-email-nikita@compulab.co.il>
	<1407690780-19645-7-git-send-email-nikita@compulab.co.il>
	<53EB7080.2080205@compulab.co.il>
Message-ID: <53F3640D.7070701@compulab.co.il>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

Hi Igor,

On 13/08/14 17:04, Igor Grinberg wrote:
> On 08/10/14 20:12, Nikita Kiryanov wrote:
>> Add USB and USB OTG host support for Compulab CM-FX6 CoM.
>>
>> Cc: Igor Grinberg <grinberg@compulab.co.il>
>> Cc: Stefano Babic <sbabic@denx.de>
>> Cc: Tom Rini <trini@ti.com>
>> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
>> ---
>> Changes in V2:
>> 	- No changes
>>
>>   board/compulab/cm_fx6/cm_fx6.c | 75 ++++++++++++++++++++++++++++++++++++++++++
>>   board/compulab/cm_fx6/common.h |  3 ++
>>   include/configs/cm_fx6.h       | 10 ++++++
>>   3 files changed, 88 insertions(+)
>>
>> diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
>> index e993de2..28c54b4 100644
>> --- a/board/compulab/cm_fx6/cm_fx6.c
>> +++ b/board/compulab/cm_fx6/cm_fx6.c
>
> [...]
>
>> +static int cm_fx6_usb_hub_reset(void)
>> +{
>> +	int err;
>> +
>> +	err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
>> +	if (err) {
>> +		printf("USB hub rst gpio request failed: %d\n", err);
>> +		return -1;
>> +	}
>> +
>> +	SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
>> +	gpio_direction_output(CM_FX6_USB_HUB_RST, 0);
>> +	udelay(10);
>> +	gpio_direction_output(CM_FX6_USB_HUB_RST, 1);
>> +	mdelay(1);
>> +
>> +	return 0;
>> +}
>> +
>> +static void cm_fx6_init_usb_otg(void)
>
> Can this function also return int as the one above?

Sure.

>
>> +{
>> +	int ret;
>> +	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
>> +
>> +	ret = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
>> +	if (ret)
>> +		printf("USB OTG pwr gpio request failed: %d\n", ret);
>> +
>> +	SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL));
>> +	SETUP_IOMUX_PAD(PAD_ENET_RX_ER__USB_OTG_ID |
>> +						MUX_PAD_CTRL(WEAK_PULLDOWN));
>> +	clrbits_le32(&iomux->gpr[1], IOMUXC_GPR1_OTG_ID_MASK);
>> +	/* disable ext. charger detect, or it'll affect signal quality at dp. */
>> +	gpio_direction_output(SB_FX6_USB_OTG_PWR, 0);
>> +}
>> +
>> +#define MX6_USBNC_BASEADDR	0x2184800
>> +#define USBNC_USB_H1_PWR_POL	(1 << 9)
>> +int board_ehci_hcd_init(int port)
>> +{
>> +	u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4);
>> +	u32 val;
>> +
>> +	switch (port) {
>> +	case 0:
>> +		cm_fx6_init_usb_otg();
>> +		break;
>> +	case 1:
>> +		SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR |
>> +						MUX_PAD_CTRL(NO_PAD_CTRL));
>> +
>> +		/* Set PWR polarity to match power switch's enable polarity */
>> +		val = __raw_readl(usbnc_usb_uh1_ctrl);
>> +		val |= USBNC_USB_H1_PWR_POL;
>> +		__raw_writel(val, usbnc_usb_uh1_ctrl);
>
> Can we have setbits_le32() here?

Sure.

>
>> +		return cm_fx6_usb_hub_reset();
>> +	default:
>> +		break;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +int board_ehci_power(int port, int on)
>> +{
>> +	return port ? 0 : gpio_direction_output(SB_FX6_USB_OTG_PWR, on);
>
> Here port is a port number, not some bool conditional.
> Please be explicit about it and don't use the construct above for such cases.

OK I'll rewrite it.