From: Stefano Babic <sbabic@denx.de>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 11/11] imx: ventana: leave PCI reset de-asserted if PCI enabled
Date: Wed, 20 Aug 2014 13:05:23 +0200 [thread overview]
Message-ID: <53F480F3.2020800@denx.de> (raw)
In-Reply-To: <1407476151-5603-12-git-send-email-tharvey@gateworks.com>
Hi Tim,
On 08/08/2014 07:35, Tim Harvey wrote:
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> ---
> board/gateworks/gw_ventana/gw_ventana.c | 8 +++-----
> 1 file changed, 3 insertions(+), 5 deletions(-)
>
> diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
> index 1c24e4b..70b90d8 100644
> --- a/board/gateworks/gw_ventana/gw_ventana.c
> +++ b/board/gateworks/gw_ventana/gw_ventana.c
> @@ -991,12 +991,10 @@ static void setup_board_gpio(int board)
> gpio_direction_output(GP_MSATA_SEL, 0);
> }
>
> - /*
> - * assert PCI_RST# (released by OS when clock is valid)
> - * TODO: figure out why leaving this de-asserted from PCI scan on boot
> - * causes linux pcie driver to hang during enumeration
> - */
> +#if !defined(CONFIG_CMD_PCI)
> + /* assert PCI_RST# (released by OS when clock is valid) */
> gpio_direction_output(gpio_cfg[board].pcie_rst, 0);
> +#endif
>
> /* turn off (active-high) user LED's */
> for (i = 0; i < 4; i++) {
>
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
prev parent reply other threads:[~2014-08-20 11:05 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-08-08 5:35 [U-Boot] [PATCH 00/11] imx: ventana: misc patches Tim Harvey
2014-08-08 5:35 ` [U-Boot] [PATCH 01/11] imx: ventana: set dynamic env var for flash layout Tim Harvey
2014-08-20 10:52 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 02/11] imx: ventana: added cputype env var Tim Harvey
2014-08-14 15:23 ` Stefano Babic
2014-08-18 13:52 ` Tim Harvey
2014-08-20 10:51 ` Stefano Babic
2014-09-09 13:19 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 03/11] imx: ventana: remove caam disable per eeprom bit Tim Harvey
2014-08-20 10:53 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 04/11] imx: ventana: add appropriate delay following GSC i2c write Tim Harvey
2014-08-20 10:54 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 05/11] imx: ventana: add econfig command Tim Harvey
2014-08-20 11:09 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 06/11] imx: ventana: add video enable gpio pinmux for GW54xx Tim Harvey
2014-08-20 10:59 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 07/11] imx: ventana: add missing crlf to print Tim Harvey
2014-08-20 11:00 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 08/11] imx: ventana: configure i2c_dis# pin properly for gw53xx Tim Harvey
2014-08-20 11:02 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 09/11] imx: ventana: enable SION bit on gpio outputs Tim Harvey
2014-08-20 11:02 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 10/11] imx: ventana: add iomux for PCISKT_WDIS# gpio Tim Harvey
2014-08-20 11:03 ` Stefano Babic
2014-08-08 5:35 ` [U-Boot] [PATCH 11/11] imx: ventana: leave PCI reset de-asserted if PCI enabled Tim Harvey
2014-08-20 11:05 ` Stefano Babic [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=53F480F3.2020800@denx.de \
--to=sbabic@denx.de \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox