[U-Boot] [PATCH] mvebu_mmc: Driver addition

[Stefan Roese <sr@denx.de>]

On 24.08.2014 21:31, Mario Schuknecht wrote:
> In function mvebu_mmc_write notice command timeout. It is possible that a
> command is done, but a timeout occurred.
>
> Enable timeout in set bus function.
>
> Set window registers. Without that I could not use the driver on a Kirkwood
> 88F6282 SoC.
>
> Set high capacity and 52MHz driver feature.

Thanks. A few review comments below.

> Signed-off-by: Mario Schuknecht <mario.schuknecht@dresearch-fe.de>
> ---
>   drivers/mmc/mvebu_mmc.c | 59 ++++++++++++++++++++++++++++++++++++++++++++++++-
>   1 file changed, 58 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/mmc/mvebu_mmc.c b/drivers/mmc/mvebu_mmc.c
> index 9759198..53754aa 100644
> --- a/drivers/mmc/mvebu_mmc.c
> +++ b/drivers/mmc/mvebu_mmc.c
> @@ -17,8 +17,12 @@
>   #include <asm/arch/kirkwood.h>
>   #include <mvebu_mmc.h>
>
> +DECLARE_GLOBAL_DATA_PTR;
> +
>   #define DRIVER_NAME "MVEBU_MMC"
>
> +#define MVEBU_TARGET_DRAM 0
> +
>   static void mvebu_mmc_write(u32 offs, u32 val)
>   {
>   	writel(val, CONFIG_SYS_MMC_BASE + (offs));
> @@ -164,6 +168,9 @@ static int mvebu_mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
>   			return TIMEOUT;
>   		}
>   	}
> +	if (mvebu_mmc_read(SDIO_ERR_INTR_STATUS) &
> +		(SDIO_ERR_CMD_TIMEOUT | SDIO_ERR_DATA_TIMEOUT))
> +		return TIMEOUT;
>
>   	/* Handling response */
>   	if (cmd->resp_type & MMC_RSP_136) {
> @@ -271,6 +278,7 @@ static void mvebu_mmc_set_bus(unsigned int bus)
>
>   	/* default to maximum timeout */
>   	ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX);
> +	ctrl_reg |= SDIO_HOST_CTRL_TMOUT_EN;
>
>   	ctrl_reg |= SDIO_HOST_CTRL_PUSH_PULL_EN;
>
> @@ -296,6 +304,53 @@ static void mvebu_mmc_set_ios(struct mmc *mmc)
>   	mvebu_mmc_set_clk(mmc->clock);
>   }
>
> +/*
> + * Set window register.
> + */
> +static void mvebu_window_setup(void)
> +{
> +	int i;
> +
> +        for (i = 0; i < 4; i++) {
> +		mvebu_mmc_write(WINDOW_CTRL(i), 0);
> +		mvebu_mmc_write(WINDOW_BASE(i), 0);
> +        }

Spaces instead of tabs for indentation. Please fix globally (checkpatch 
clean)

> +	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
> +		u32 size, base, attrib;
> +
> +		/* Enable DRAM bank */
> +		switch (i) {
> +		case 0:
> +			attrib = KWCPU_ATTR_DRAM_CS0;
> +			break;
> +		case 1:
> +			attrib = KWCPU_ATTR_DRAM_CS1;
> +			break;
> +		case 2:
> +			attrib = KWCPU_ATTR_DRAM_CS2;
> +			break;
> +		case 3:
> +			attrib = KWCPU_ATTR_DRAM_CS3;
> +			break;
> +		default:
> +			/* invalide bank, disable access */
> +			attrib = 0;
> +			break;
> +		}
> +
> +		size = gd->bd->bi_dram[i].size;
> +		base = gd->bd->bi_dram[i].start;
> +		if ((size) && (attrib))

size and attrib don't need parentheses here.

> +			mvebu_mmc_write(WINDOW_CTRL(i),
> +				MVCPU_WIN_CTRL_DATA(size, MVEBU_TARGET_DRAM,
> +					attrib, MVCPU_WIN_ENABLE));
> +		else
> +			mvebu_mmc_write(WINDOW_CTRL(i), MVCPU_WIN_DISABLE);

Please use correct coding style for multi-line statements. So this
should look like this:

	if (size && attrib) {
		mvebu_mmc_write(WINDOW_CTRL(i),
			MVCPU_WIN_CTRL_DATA(size, MVEBU_TARGET_DRAM,
					attrib, MVCPU_WIN_ENABLE));
	} else {
		mvebu_mmc_write(WINDOW_CTRL(i), MVCPU_WIN_DISABLE);
	}

Thanks,
Stefan