public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
* [U-Boot] [PATCH] imx6: add Bachmann OT1200 board v2
@ 2014-09-22 11:57 Christian Gmeiner
  2014-09-22 11:57 ` [U-Boot] [PATCH] kconfiglib: change SPDX-License-Identifier to ISC Christian Gmeiner
  2014-09-29  8:46 ` [U-Boot] [PATCH] imx6: add Bachmann OT1200 board v2 Stefano Babic
  0 siblings, 2 replies; 5+ messages in thread
From: Christian Gmeiner @ 2014-09-22 11:57 UTC (permalink / raw)
  To: u-boot

This patch adds support for the OT1200 series of devices.

Following components are used in u-boot:
+ ethernet
+ i2c
+ emmc
+ gpio

For more details see README.

Changes v1 > v2
  - make use of enable_cspi_clock(..)
  - fix usage of OUTPUT_40OHM define
  - added README

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
---
 arch/arm/Kconfig                  |   4 +
 board/bachmann/ot1200/Kconfig     |  23 ++++
 board/bachmann/ot1200/MAINTAINERS |   6 +
 board/bachmann/ot1200/Makefile    |   9 ++
 board/bachmann/ot1200/README      |  20 +++
 board/bachmann/ot1200/ot1200.c    | 251 ++++++++++++++++++++++++++++++++++++++
 configs/ot1200_defconfig          |   3 +
 include/configs/ot1200.h          | 196 +++++++++++++++++++++++++++++
 8 files changed, 512 insertions(+)
 create mode 100644 board/bachmann/ot1200/Kconfig
 create mode 100644 board/bachmann/ot1200/MAINTAINERS
 create mode 100644 board/bachmann/ot1200/Makefile
 create mode 100644 board/bachmann/ot1200/README
 create mode 100644 board/bachmann/ot1200/ot1200.c
 create mode 100644 configs/ot1200_defconfig
 create mode 100644 include/configs/ot1200.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 106aed9..8face21 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -414,6 +414,9 @@ config TARGET_HUMMINGBOARD
 config TARGET_TQMA6
 	bool "TQ Systems TQMa6 board"
 
+config TARGET_OT1200
+	bool "Bachmann OT1200"
+
 config OMAP34XX
 	bool "OMAP34XX SoC"
 
@@ -577,6 +580,7 @@ source "board/atmel/at91sam9rlek/Kconfig"
 source "board/atmel/at91sam9x5ek/Kconfig"
 source "board/atmel/sama5d3_xplained/Kconfig"
 source "board/atmel/sama5d3xek/Kconfig"
+source "board/bachmann/ot1200/Kconfig"
 source "board/balloon3/Kconfig"
 source "board/barco/titanium/Kconfig"
 source "board/bluegiga/apx4devkit/Kconfig"
diff --git a/board/bachmann/ot1200/Kconfig b/board/bachmann/ot1200/Kconfig
new file mode 100644
index 0000000..55a825d
--- /dev/null
+++ b/board/bachmann/ot1200/Kconfig
@@ -0,0 +1,23 @@
+if TARGET_OT1200
+
+config SYS_CPU
+	string
+	default "armv7"
+
+config SYS_BOARD
+	string
+	default "ot1200"
+
+config SYS_VENDOR
+	string
+	default "bachmann"
+
+config SYS_SOC
+	string
+	default "mx6"
+
+config SYS_CONFIG_NAME
+	string
+	default "ot1200"
+
+endif
diff --git a/board/bachmann/ot1200/MAINTAINERS b/board/bachmann/ot1200/MAINTAINERS
new file mode 100644
index 0000000..ad75c24
--- /dev/null
+++ b/board/bachmann/ot1200/MAINTAINERS
@@ -0,0 +1,6 @@
+BACHMANN ELECTRONIC OT1200 BOARD
+M:	Christian Gmeiner <christian.gmeiner@gmail.com>
+S:	Maintained
+F:	board/bachmann/ot1200
+F:	include/configs/ot1200.h
+F:	configs/ot1200*_defconfig
diff --git a/board/bachmann/ot1200/Makefile b/board/bachmann/ot1200/Makefile
new file mode 100644
index 0000000..1bd42e8
--- /dev/null
+++ b/board/bachmann/ot1200/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright (C) 2012-2013, Guennadi Liakhovetski <lg@denx.de>
+# (C) Copyright 2012-2013 Freescale Semiconductor, Inc.
+# Copyright (C) 2013, Boundary Devices <info@boundarydevices.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := ot1200.o
diff --git a/board/bachmann/ot1200/README b/board/bachmann/ot1200/README
new file mode 100644
index 0000000..efcff11
--- /dev/null
+++ b/board/bachmann/ot1200/README
@@ -0,0 +1,20 @@
+U-Boot for the Bachmann electronic GmbH OT1200 devices
+
+There are two different versions of the base print, which differ
+in the way ethernet is done. The variant detection is done during
+runtime based on the address of the found phy.
+
+- "mr" variant
+FEC is connected directly to an ethernet switch (KSZ8895). The ethernet
+port is always up and auto-negotiation is not possible.
+
+- normal variant
+FEC is connected to a normal phy and auto-negotiation is possible.
+
+
+The variant name is part of the dtb file name loaded by u-boot. This
+make is possible to boot the linux kernel and make use variant specific
+devicetree (fixed-phy link).
+
+In order to support different display resoltuions/sizes the OT1200 devices
+are making use of EDID data stored in an i2c EEPROM.
\ No newline at end of file
diff --git a/board/bachmann/ot1200/ot1200.c b/board/bachmann/ot1200/ot1200.c
new file mode 100644
index 0000000..0d5ede5
--- /dev/null
+++ b/board/bachmann/ot1200/ot1200.c
@@ -0,0 +1,251 @@
+/*
+ * Copyright (C) 2010-2013 Freescale Semiconductor, Inc.
+ * Copyright (C) 2014, Bachmann electronic GmbH
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <malloc.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/arch/crm_regs.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <netdev.h>
+#include <i2c.h>
+#include <pca953x.h>
+#include <asm/gpio.h>
+#include <phy.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define OUTPUT_40OHM	(PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm)
+
+#define UART_PAD_CTRL	(PAD_CTL_PUS_100K_UP |			\
+	OUTPUT_40OHM | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL	(PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL	(PAD_CTL_PUS_100K_UP | OUTPUT_40OHM |	\
+	PAD_CTL_HYS)
+
+#define SPI_PAD_CTRL	(PAD_CTL_HYS | OUTPUT_40OHM |		\
+	PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL	(PAD_CTL_PUS_100K_UP | OUTPUT_40OHM |	\
+	PAD_CTL_HYS | PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+static iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_KEY_ROW1__ENET_COL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_COL3__ENET_CRS | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_GPIO_18__ENET_RX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_COL2__ENET_RX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_COL0__ENET_RX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_ROW2__ENET_TX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_KEY_ROW0__ENET_TX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+}
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_DISP0_DAT3__ECSPI3_SS0  | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT4__ECSPI3_SS1  | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+
+static void setup_iomux_spi(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	setup_iomux_spi();
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return 1;
+}
+
+struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{USDHC3_BASE_ADDR},
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+	usdhc_cfg[0].max_bus_width = 8;
+
+	imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+/* I2C3 - IO expander  */
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
+		.gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
+		.gp = IMX_GPIO_NR(3, 17)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
+		.gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
+		.gp = IMX_GPIO_NR(3, 18)
+	}
+};
+
+static iomux_v3_cfg_t const pwm_pad[] = {
+	MX6_PAD_SD1_CMD__PWM4_OUT | MUX_PAD_CTRL(OUTPUT_40OHM),
+};
+
+static void leds_on(void)
+{
+	/* turn on all possible leds connected via GPIO expander */
+	i2c_set_bus_num(2);
+	pca953x_set_dir(CONFIG_SYS_I2C_PCA953X_ADDR, 0xffff, PCA953X_DIR_OUT);
+	pca953x_set_val(CONFIG_SYS_I2C_PCA953X_ADDR, 0xffff, 0x0);
+}
+
+static void backlight_lcd_off(void)
+{
+	unsigned gpio = IMX_GPIO_NR(2, 0);
+	gpio_direction_output(gpio, 0);
+
+	gpio = IMX_GPIO_NR(2, 3);
+	gpio_direction_output(gpio, 0);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	uint32_t base = IMX_FEC_BASE;
+	struct mii_dev *bus = NULL;
+	struct phy_device *phydev = NULL;
+	int ret;
+
+	setup_iomux_enet();
+
+	bus = fec_get_miibus(base, -1);
+	if (!bus)
+		return 0;
+
+	/* scan phy 0 and 5 */
+	phydev = phy_find_by_mask(bus, 0x21, PHY_INTERFACE_MODE_RGMII);
+	if (!phydev) {
+		free(bus);
+		return 0;
+	}
+
+	/* depending on the phy address we can detect our board version */
+	if (phydev->addr == 0)
+		setenv("boardver", "");
+	else
+		setenv("boardver", "mr");
+
+	printf("using phy at %d\n", phydev->addr);
+	ret = fec_probe(bis, -1, base, bus, phydev);
+	if (ret) {
+		printf("FEC MXC: %s:failed\n", __func__);
+		free(phydev);
+		free(bus);
+	}
+	return 0;
+}
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	backlight_lcd_off();
+
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+
+	leds_on();
+
+	/* enable ecspi3 clocks */
+	enable_cspi_clock(1, 2);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: "CONFIG_SYS_BOARD"\n");
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"mmc0",	MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+	{NULL,		0},
+};
+#endif
+
+int misc_init_r(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+	return 0;
+}
diff --git a/configs/ot1200_defconfig b/configs/ot1200_defconfig
new file mode 100644
index 0000000..11797ce
--- /dev/null
+++ b/configs/ot1200_defconfig
@@ -0,0 +1,3 @@
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q"
+CONFIG_ARM=y
+CONFIG_TARGET_OT1200=y
diff --git a/include/configs/ot1200.h b/include/configs/ot1200.h
new file mode 100644
index 0000000..8fb8177
--- /dev/null
+++ b/include/configs/ot1200.h
@@ -0,0 +1,196 @@
+/*
+ * Copyright (C) 2010-2013 Freescale Semiconductor, Inc.
+ * Copyright (C) 2014 Bachmann electronic GmbH
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "mx6_common.h"
+#define CONFIG_MX6
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MISC_INIT_R
+#define CONFIG_MXC_GPIO
+
+/* FUSE Configs */
+#define CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+
+/* UART Configs */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE           UART1_BASE
+
+/* SF Configs */
+#define CONFIG_CMD_SF
+#define CONFIG_SPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SPI_FLASH_MACRONIX
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_MXC_SPI
+#define CONFIG_SF_DEFAULT_BUS  2
+#define CONFIG_SF_DEFAULT_CS   (0|(IMX_GPIO_NR(1, 3)<<8))
+#define CONFIG_SF_DEFAULT_SPEED 25000000
+#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
+
+/* IO expander */
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_ADDR	0x20
+#define CONFIG_SYS_I2C_PCA953X_WIDTH	{ {0x20, 16} }
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+
+/* I2C Configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED            100000
+
+/* OCOTP Configs */
+#define CONFIG_CMD_IMXOTP
+#define CONFIG_IMX_OTP
+#define IMX_OTP_BASE                    OCOTP_BASE_ADDR
+#define IMX_OTP_ADDR_MAX                0x7F
+#define IMX_OTP_DATA_ERROR_VAL          0xBADABADA
+#define IMX_OTPWRITE_ENABLED
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR      0
+#define CONFIG_SYS_FSL_USDHC_NUM       2
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+
+#ifdef CONFIG_MX6Q
+#define CONFIG_CMD_SATA
+#endif
+
+/*
+ * SATA Configs
+ */
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_DWC_AHSATA_PORT_ID	0
+#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE                    ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE             MII100
+#define CONFIG_ETHPRIME                 "FEC"
+#define CONFIG_FEC_MXC_PHYADDR          0x5
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+/* Miscellaneous commands */
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_SETEXPR
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX              1
+#define CONFIG_BAUDRATE                115200
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY               2
+
+#define CONFIG_PREBOOT                 ""
+
+#define CONFIG_LOADADDR                0x12000000
+#define CONFIG_SYS_TEXT_BASE           0x17800000
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_CBSIZE              1024
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS             16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS           1
+#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE                (1u * 1024 * 1024 * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SIZE                 (64 * 1024)	/* 64 kb */
+#define CONFIG_ENV_OFFSET               (1024 * 1024)
+#define CONFIG_ENV_SECT_SIZE            (64 * 1024)	/* M25P16 has an erase size of 64 KiB */
+#define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_SUPPORT_RAW_INITRD
+
+/* FS Configs */
+#define CONFIG_CMD_EXT3
+#define CONFIG_CMD_EXT4
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FS_GENERIC
+
+#define CONFIG_BOOTP_SERVERIP
+#define CONFIG_BOOTP_BOOTFILE
+
+#endif         /* __CONFIG_H */
-- 
1.9.3

^ permalink raw reply related	[flat|nested] 5+ messages in thread
end of thread, other threads:[~2014-10-01 12:22 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-09-22 11:57 [U-Boot] [PATCH] imx6: add Bachmann OT1200 board v2 Christian Gmeiner
2014-09-22 11:57 ` [U-Boot] [PATCH] kconfiglib: change SPDX-License-Identifier to ISC Christian Gmeiner
2014-09-22 12:55   ` Christian Gmeiner
2014-09-29  8:46 ` [U-Boot] [PATCH] imx6: add Bachmann OT1200 board v2 Stefano Babic
2014-10-01 12:22   ` Christian Gmeiner

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox