[U-Boot] [PATCH v3 07/11] imx: Add error checking to setup_i2c()

[Nikita Kiryanov <nikita@compulab.co.il>]

Hi Simon,

On 17/09/14 18:02, Simon Glass wrote:
> Since this function can fail, check its return value.
>
> Signed-off-by: Simon Glass <sjg@chromium.org>
> ---
>
> Changes in v3:
> - Just warn when one of the board init stages fails
>
> Changes in v2:
> - Add new patch to add error checking to setup_i2c()
>
>   arch/arm/imx-common/i2c-mxv7.c            | 24 ++++++++++---
>   arch/arm/include/asm/imx-common/mxc_i2c.h |  4 +--
>   board/compulab/cm_fx6/cm_fx6.c            | 56 ++++++++++++++++++++++++++-----
>   3 files changed, 68 insertions(+), 16 deletions(-)
>
> diff --git a/arch/arm/imx-common/i2c-mxv7.c b/arch/arm/imx-common/i2c-mxv7.c
> index a580873..70cff5c 100644
> --- a/arch/arm/imx-common/i2c-mxv7.c
> +++ b/arch/arm/imx-common/i2c-mxv7.c
> @@ -69,15 +69,29 @@ static void * const i2c_bases[] = {
>   };
>
>   /* i2c_index can be from 0 - 2 */
> -void setup_i2c(unsigned i2c_index, int speed, int slave_addr,
> -		struct i2c_pads_info *p)
> +int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
> +	      struct i2c_pads_info *p)
>   {
> +	int ret;
> +
>   	if (i2c_index >= ARRAY_SIZE(i2c_bases))
> -		return;
> +		return -EINVAL;
>   	/* Enable i2c clock */
> -	enable_i2c_clk(1, i2c_index);
> +	ret = enable_i2c_clk(1, i2c_index);
> +	if (ret)
> +		goto err_clk;
> +
>   	/* Make sure bus is idle */
> -	force_idle_bus(p);
> +	ret = force_idle_bus(p);
> +	if (ret)
> +		goto err_idle;
> +
>   	bus_i2c_init(i2c_bases[i2c_index], speed, slave_addr,
>   			force_idle_bus, p);
> +
> +	return 0;
> +
> +err_idle:
> +err_clk:
> +	return ret;
>   }
> diff --git a/arch/arm/include/asm/imx-common/mxc_i2c.h b/arch/arm/include/asm/imx-common/mxc_i2c.h
> index 182c2f3..af86163 100644
> --- a/arch/arm/include/asm/imx-common/mxc_i2c.h
> +++ b/arch/arm/include/asm/imx-common/mxc_i2c.h
> @@ -52,8 +52,8 @@ struct i2c_pads_info {
>   					&mx6q_##name : &mx6s_##name
>   #endif
>
> -void setup_i2c(unsigned i2c_index, int speed, int slave_addr,
> -		struct i2c_pads_info *p);
> +int setup_i2c(unsigned i2c_index, int speed, int slave_addr,
> +	      struct i2c_pads_info *p);
>   void bus_i2c_init(void *base, int speed, int slave_addr,
>   		int (*idle_bus_fn)(void *p), void *p);
>   int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf,
> diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
> index fdb8ebf..10a568f 100644
> --- a/board/compulab/cm_fx6/cm_fx6.c
> +++ b/board/compulab/cm_fx6/cm_fx6.c
> @@ -69,7 +69,7 @@ static iomux_v3_cfg_t const sata_pads[] = {
>   	IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31   | MUX_PAD_CTRL(NO_PAD_CTRL)),
>   };
>
> -static void cm_fx6_setup_issd(void)
> +static int cm_fx6_setup_issd(void)
>   {
>   	SETUP_IOMUX_PADS(sata_pads);
>   	/* Make sure this gpio has logical 0 value */
> @@ -79,14 +79,24 @@ static void cm_fx6_setup_issd(void)
>   	cm_fx6_sata_power(0);
>   	mdelay(250);
>   	cm_fx6_sata_power(1);
> +
> +	return 0;
>   }
>
>   #define CM_FX6_SATA_INIT_RETRIES	10
>   int sata_initialize(void)
>   {
> -	int err, i;
> +	int err, i, ret;
>
> -	cm_fx6_setup_issd();
> +	/*
> +	 * cm-fx6 may have iSSD not assembled and in this case it has
> +	 * bypasses for a (m)SATA socket on the baseboard. The socketed
> +	 * device is not controlled by those GPIOs. So just print a warning
> +	 * if the setup fails.
> +	 */
> +	ret = cm_fx6_setup_issd();
> +	if (ret)
> +		printf("Warning: iSSD setup failed!\n");
>   	for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
>   		err = setup_sata();
>   		if (err) {

The issd stuff above is unrelated to the subject of this patch. It
should be part of the next patch.

Aside from that,
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>


-- 
Regards,
Nikita Kiryanov