From mboxrd@z Thu Jan  1 00:00:00 1970
From: Stefano Babic <sbabic@denx.de>
Date: Mon, 06 Oct 2014 17:35:54 +0200
Subject: [U-Boot] [PATCH 00/32] ARM: i.MX: nitrogen6x clean up
In-Reply-To: <1412277413-30271-1-git-send-email-eric.nelson@boundarydevices.com>
References: <1412277413-30271-1-git-send-email-eric.nelson@boundarydevices.com>
Message-ID: <5432B6DA.20001@denx.de>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

Hi Eric,

On 02/10/2014 21:16, Eric Nelson wrote:
> This collection of patches comprises a set of updates that have
> been lingering in our Github repository.
> 
> We're pushing them to main-line in preparation for the addition
> of a couple of boards that have also been lingering for a while.
> 
> Patches 1-9 are tweaks to the mx6qsabrelite/nitrogen6x initialization
> code.
> 
> Patches 10-18 add support for additional displays supported by
> the board(s) and tweak the HDMI detection.
> 
> Patches 19-32 enable and configure various features through
> changes to include/configs/nitrogen6x.h.
> 

Patches are orthogonal and can be applied separetely. I have not seen
any comments and I have not comments for most of them. I will start to
apply the ones (most of them) are straightforward. Please wait until I
end up with first pass - your next version will be much shorter !

> Diego Rondini (1):
>   nitrogen6x: config: allow boot to USB stick
> 
> Eric Nelson (24):
>   nitrogen6x: implement board_cfb_skip() to disable text output
>   nitrogen6x: configure SD2 pads for SDIO on USDHC2
>   nitrogen6x: power-down miscellanous peripherals
>   nitrogen6x: staticize board file
>   nitrogen6x: Allow U-Boot to be silent on UART2
>   nitrogen6x: prevent warnings about board_ehci* callbacks
>   nitrogen6x: display: add qvga panel
>   nitrogen6x: display: add support for LG-9.7 LVDS display
>   nitrogen6x: display: add LDB-WXGA-S for SPWG 1280x800 displays
>   nitrogen6x: display: add support for fusion 7 display
>   nitrogen6x: display: add svga display (800x600)
>   nitrogen6x: display: add Ampire 1024x600 panel
>   nitrogen6x: display: add wvga-lvds panel
>   nitrogen6x: display use I2C detect for HDMI
>   nitrogen6x: config: add USB Mass Storage (ums) support
>   nitrogen6x: config: add initrd_high
>   nitrogen6x: config: expose SATA, then MMC over USB
>   nitrogen6x: config: enable USB keyboard support
>   nitrogen6x: config: add CONFIG_CMD_MEMTEST
>   nitrogen6x: config: enable "i2c edid"
>   nitrogen6x: config: disable logo
>   nitrogen6x: config: configure usb_ether

Mainly I have problems with fixed addresses - my comments to the related
patch.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================