[U-Boot] [PATCH 1/5] imx:mx6sxsabresd add usb support

[Stefano Babic <sbabic@denx.de>]

Hi Peng,

On 01/11/2014 03:19, Peng Fan wrote:
> Add usb support for mx6sxsabresd board.
> 
> Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
> Signed-off-by: Ye.Li <B37916@freescale.com>
> ---
>  board/freescale/mx6sxsabresd/mx6sxsabresd.c | 29 +++++++++++++++++++++++++++++
>  include/configs/mx6sxsabresd.h              | 14 ++++++++++++++
>  2 files changed, 43 insertions(+)
> 
> diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
> index 256ea29..016b8e8 100644
> --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
> +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
> @@ -296,3 +296,32 @@ int checkboard(void)
>  
>  	return 0;
>  }
> +
> +#ifdef CONFIG_USB_EHCI_MX6
> +iomux_v3_cfg_t const usb_otg1_pads[] = {
> +	MX6_PAD_GPIO1_IO09__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
> +	MX6_PAD_GPIO1_IO10__ANATOP_OTG1_ID | MUX_PAD_CTRL(NO_PAD_CTRL)
> +};
> +
> +iomux_v3_cfg_t const usb_otg2_pads[] = {
> +	MX6_PAD_GPIO1_IO12__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
> +};
> +
> +int board_ehci_hcd_init(int port)
> +{
> +	switch (port) {
> +	case 0:
> +		imx_iomux_v3_setup_multiple_pads(usb_otg1_pads,
> +						 ARRAY_SIZE(usb_otg1_pads));
> +		break;
> +	case 1:
> +		imx_iomux_v3_setup_multiple_pads(usb_otg2_pads,
> +						 ARRAY_SIZE(usb_otg2_pads));
> +		break;
> +	default:
> +		printf("MXC USB port %d not yet supported\n", port);
> +		return 1;
> +	}
> +	return 0;
> +}
> +#endif

Frankly, I am expecting that this function power up the bus instead of
pin multiplexing. If the pins are reserved for USB, why should we set
the pinmux each time board_ehci_hcd_init() is called ? And, in any case,
pins are not reset after their usage for USB. You can move this setup in
board_init() or in another init function.

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================