public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
From: Nikita Kiryanov <nikita@compulab.co.il>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH] arm: imx: make bmode command work with SPL/U-Boot combo
Date: Tue, 11 Nov 2014 17:29:08 +0200	[thread overview]
Message-ID: <54622B44.1090700@compulab.co.il> (raw)
In-Reply-To: <1414603713-15155-1-git-send-email-nikita@compulab.co.il>

Gentle ping.

On 10/29/2014 07:28 PM, Nikita Kiryanov wrote:
> The bmode command forces the SoC to use a specific boot device
> by writing its boot mode into SRC_GPR9, and notifying the SoC of
> the change using SRC_GPR10[28] bit: if the bit is on, bootROM
> uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine
> the boot device.
>
> SPL on the other hand is oblivious to this distinction, so once
> the bootROM loads SPL from the device configured in SRC_GPR10,
> SPL will attempt to load U-Boot from the device configured in
> SRC_SMBR1, which is not updated by the bootROM to the value in
> SRC_GPR9.
>
> The result is that the selected boot device is not used across all
> the boot stages.
>
> Update spl_boot_device() to look at gpr9 when necessary.
>
> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
> Cc: Stefano Babic <sbabic@denx.de>
> Cc: Troy Kisky <troy.kisky@boundarydevices.com>
> Cc: Tim Harvey <tharvey@gateworks.com>
> Cc: Eric Nelson <eric.nelson@boundarydevices.com>
> Cc: Fabio Estevam <fabio.estevam@freescale.com>
> Cc: Heiko Schocher <hs@denx.de>
> ---
>   arch/arm/cpu/armv7/mx6/soc.c | 4 ++--
>   arch/arm/imx-common/spl.c    | 5 +++--
>   2 files changed, 5 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
> index dd5aaa2..07ae79e 100644
> --- a/arch/arm/cpu/armv7/mx6/soc.c
> +++ b/arch/arm/cpu/armv7/mx6/soc.c
> @@ -333,8 +333,8 @@ void boot_mode_apply(unsigned cfg_val)
>   /*
>    * cfg_val will be used for
>    * Boot_cfg4[7:0]:Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0]
> - * After reset, if GPR10[28] is 1, ROM will copy GPR9[25:0]
> - * to SBMR1, which will determine the boot device.
> + * After reset, if GPR10[28] is 1, ROM will use GPR9[25:0]
> + * instead of SBMR1 to determine the boot device.
>    */
>   const struct boot_mode soc_boot_modes[] = {
>   	{"normal",	MAKE_CFGVAL(0x00, 0x00, 0x00, 0x00)},
> diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
> index 9d3c31a..477c38c 100644
> --- a/arch/arm/imx-common/spl.c
> +++ b/arch/arm/imx-common/spl.c
> @@ -14,11 +14,12 @@
>   #include <spl.h>
>
>   #if defined(CONFIG_MX6)
> -/* determine boot device from SRC_SBMR1 register (BOOT_CFG[4:1]) */
> +/* determine boot device from SRC_SBMR1 (BOOT_CFG[4:1]) or SRC_GPR9 register */
>   u32 spl_boot_device(void)
>   {
>   	struct src *psrc = (struct src *)SRC_BASE_ADDR;
> -	unsigned reg = readl(&psrc->sbmr1);
> +	unsigned int gpr10_boot = readl(&psrc->gpr10) & (1 << 28);
> +	unsigned reg = gpr10_boot ? readl(&psrc->gpr9) : readl(&psrc->sbmr1);
>
>   	/* BOOT_CFG1[7:4] - see IMX6DQRM Table 8-8 */
>   	switch ((reg & 0x000000FF) >> 4) {
>

-- 
Regards,
Nikita Kiryanov

  reply	other threads:[~2014-11-11 15:29 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-10-29 17:28 [U-Boot] [PATCH] arm: imx: make bmode command work with SPL/U-Boot combo Nikita Kiryanov
2014-11-11 15:29 ` Nikita Kiryanov [this message]
2014-11-12  8:05 ` Stefano Babic

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=54622B44.1090700@compulab.co.il \
    --to=nikita@compulab.co.il \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox