[U-Boot] [PATCH v3 1/5] power: pfuze100: Update definitions for buck regulators

[U-Boot] [PATCH v3 1/5] power: pfuze100: Update definitions for buck regulators

[Ye.Li]

Add definitions for buck regulators (SW1A/B/C) registers and voltage
values.

Signed-off-by: Ye.Li <B37916@freescale.com>
---
Changes since v1:
- None

Changes since v2:
- Create this patch for updating registers definitions and magic value.

 include/power/pfuze100_pmic.h |   80 +++++++++++++++++++++++++++++++++++++++++
 1 files changed, 80 insertions(+), 0 deletions(-)

diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h
index 0002f1e..1118489 100644
--- a/include/power/pfuze100_pmic.h
+++ b/include/power/pfuze100_pmic.h
@@ -38,6 +38,86 @@ enum {
 };
 
 /*
+ * Buck Regulators
+ */
+
+/* SW1A/B/C Output Voltage Configuration */
+#define SW1x_0_300V 0
+#define SW1x_0_325V 1
+#define SW1x_0_350V 2
+#define SW1x_0_375V 3
+#define SW1x_0_400V 4
+#define SW1x_0_425V 5
+#define SW1x_0_450V 6
+#define SW1x_0_475V 7
+#define SW1x_0_500V 8
+#define SW1x_0_525V 9
+#define SW1x_0_550V 10
+#define SW1x_0_575V 11
+#define SW1x_0_600V 12
+#define SW1x_0_625V 13
+#define SW1x_0_650V 14
+#define SW1x_0_675V 15
+#define SW1x_0_700V 16
+#define SW1x_0_725V 17
+#define SW1x_0_750V 18
+#define SW1x_0_775V 19
+#define SW1x_0_800V 20
+#define SW1x_0_825V 21
+#define SW1x_0_850V 22
+#define SW1x_0_875V 23
+#define SW1x_0_900V 24
+#define SW1x_0_925V 25
+#define SW1x_0_950V 26
+#define SW1x_0_975V 27
+#define SW1x_1_000V 28
+#define SW1x_1_025V 29
+#define SW1x_1_050V 30
+#define SW1x_1_075V 31
+#define SW1x_1_100V 32
+#define SW1x_1_125V 33
+#define SW1x_1_150V 34
+#define SW1x_1_175V 35
+#define SW1x_1_200V 36
+#define SW1x_1_225V 37
+#define SW1x_1_250V 38
+#define SW1x_1_275V 39
+#define SW1x_1_300V 40
+#define SW1x_1_325V 41
+#define SW1x_1_350V 42
+#define SW1x_1_375V 43
+#define SW1x_1_400V 44
+#define SW1x_1_425V 45
+#define SW1x_1_450V 46
+#define SW1x_1_475V 47
+#define SW1x_1_500V 48
+#define SW1x_1_525V 49
+#define SW1x_1_550V 50
+#define SW1x_1_575V 51
+#define SW1x_1_600V 52
+#define SW1x_1_625V 53
+#define SW1x_1_650V 54
+#define SW1x_1_675V 55
+#define SW1x_1_700V 56
+#define SW1x_1_725V 57
+#define SW1x_1_750V 58
+#define SW1x_1_775V 59
+#define SW1x_1_800V 60
+#define SW1x_1_825V 61
+#define SW1x_1_850V 62
+#define SW1x_1_875V 63
+
+#define SW1x_NORMAL_MASK  0x3f
+#define SW1x_STBY_MASK    0x3f
+#define SW1x_OFF_MASK     0x3f
+
+#define SW1xCONF_DVSSPEED_MASK 0xc0
+#define SW1xCONF_DVSSPEED_2US  0x00
+#define SW1xCONF_DVSSPEED_4US  0x40
+#define SW1xCONF_DVSSPEED_8US  0x80
+#define SW1xCONF_DVSSPEED_16US 0xc0
+
+/*
  * LDO Configuration
  */
 
-- 
1.7.4.1

[U-Boot] [PATCH v3 2/5] imx: mx6sabre common: Factorize the Pfuze init function

[Ye.Li]

Since the Pfuze initializations are similar on various mx6 SABRE
boards. Factorize the initialization to a common function in file
board/freescale/common/pfuze.c. So that all SABRE boards BSP can
share the function.

Signed-off-by: Ye.Li <B37916@freescale.com>
---
Changes since v1:
- Factorize the pfuze init function for sabre boards

Changes since v2:
- Replace the magic value to definitions in pfuze driver.

 board/freescale/common/Makefile |    1 +
 board/freescale/common/pfuze.c  |   54 +++++++++++++++++++++++++++++++++++++++
 board/freescale/common/pfuze.h  |   12 ++++++++
 3 files changed, 67 insertions(+), 0 deletions(-)
 create mode 100644 board/freescale/common/pfuze.c
 create mode 100644 board/freescale/common/pfuze.h

diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 32b5a3b..25a1bc1 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -53,6 +53,7 @@ obj-$(CONFIG_P5040DS)		+= ics307_clk.o
 obj-$(CONFIG_VSC_CROSSBAR)    += vsc3316_3308.o
 obj-$(CONFIG_IDT8T49N222A)	+= idt8t49n222a_serdes_clk.o
 obj-$(CONFIG_ZM7300)		+= zm7300.o
+obj-$(CONFIG_POWER_PFUZE100)	+= pfuze.o
 
 # deal with common files for P-series corenet based devices
 obj-$(CONFIG_P2041RDB)	+= p_corenet/
diff --git a/board/freescale/common/pfuze.c b/board/freescale/common/pfuze.c
new file mode 100644
index 0000000..b6893c7
--- /dev/null
+++ b/board/freescale/common/pfuze.c
@@ -0,0 +1,54 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+
+struct pmic * pfuze_common_init(unsigned char i2cbus)
+{
+	struct pmic *p;
+	int ret;
+	unsigned int reg;
+
+	ret = power_pfuze100_init(i2cbus);
+	if (ret)
+		return NULL;
+
+	p = pmic_get("PFUZE100");
+	ret = pmic_probe(p);
+	if (ret)
+		return NULL;
+
+	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
+	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
+
+	/* Set SW1AB stanby volage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
+	reg &= ~SW1x_STBY_MASK;
+	reg |= SW1x_0_975V;
+	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
+
+	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PUZE_100_SW1ABCONF, &reg);
+	reg &= ~SW1xCONF_DVSSPEED_MASK;
+	reg |= SW1xCONF_DVSSPEED_4US;
+	pmic_reg_write(p, PUZE_100_SW1ABCONF, reg);
+
+	/* Set SW1C standby voltage to 0.975V */
+	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
+	reg &= ~SW1x_STBY_MASK;
+	reg |= SW1x_0_975V;
+	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
+
+	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
+	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
+	reg &= ~SW1xCONF_DVSSPEED_MASK;
+	reg |= SW1xCONF_DVSSPEED_4US;
+	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
+
+	return p;
+}
diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h
new file mode 100644
index 0000000..c5d1771
--- /dev/null
+++ b/board/freescale/common/pfuze.h
@@ -0,0 +1,12 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __PFUZE_BOARD_HELPER__
+#define __PFUZE_BOARD_HELPER__
+
+struct pmic * pfuze_common_init(unsigned char i2cbus);
+
+#endif
-- 
1.7.4.1

[U-Boot] [PATCH v3 3/5] imx: mx6sabresd: Use the pfuze common init function

[Ye.Li]

Modify the pfuze init for mx6sabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.

Signed-off-by: Ye.Li <B37916@freescale.com>
---
Changes since v1:
- Change to use pfuze common init function for sabre boards.

Changes since v2:
- Move the pfuze init to power_init_board

 board/freescale/mx6sabresd/mx6sabresd.c |   52 +++++-------------------------
 1 files changed, 9 insertions(+), 43 deletions(-)

diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 3d81fff..bc3cd25 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -27,6 +27,7 @@
 #include <i2c.h>
 #include <power/pmic.h>
 #include <power/pfuze100_pmic.h>
+#include "../common/pfuze.h"
 DECLARE_GLOBAL_DATA_PTR;
 
 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
@@ -517,60 +518,27 @@ int board_init(void)
 	return 0;
 }
 
-static int pfuze_init(void)
+int power_init_board(void)
 {
 	struct pmic *p;
-	int ret;
 	unsigned int reg;
 
-	ret = power_pfuze100_init(I2C_PMIC);
-	if (ret)
-		return ret;
-
-	p = pmic_get("PFUZE100");
-	ret = pmic_probe(p);
-	if (ret)
-		return ret;
-
-	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
-	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
+	p = pfuze_common_init(I2C_PMIC);
+	if (!p)
+		return -ENODEV;
 
 	/* Increase VGEN3 from 2.5 to 2.8V */
 	pmic_reg_read(p, PFUZE100_VGEN3VOL, &reg);
-	reg &= ~0xf;
-	reg |= 0xa;
+	reg &= ~LDO_VOL_MASK;
+	reg |= LDOB_2_80V;
 	pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
 
 	/* Increase VGEN5 from 2.8 to 3V */
 	pmic_reg_read(p, PFUZE100_VGEN5VOL, &reg);
-	reg &= ~0xf;
-	reg |= 0xc;
+	reg &= ~LDO_VOL_MASK;
+	reg |= LDOB_3_00V;
 	pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
 
-	/* Set SW1AB stanby volage to 0.975V */
-	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
-	reg &= ~0x3f;
-	reg |= 0x1b;
-	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
-
-	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
-	pmic_reg_read(p, PUZE_100_SW1ABCONF, &reg);
-	reg &= ~0xc0;
-	reg |= 0x40;
-	pmic_reg_write(p, PUZE_100_SW1ABCONF, reg);
-
-	/* Set SW1C standby voltage to 0.975V */
-	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
-	reg &= ~0x3f;
-	reg |= 0x1b;
-	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
-
-	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
-	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
-	reg &= ~0xc0;
-	reg |= 0x40;
-	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
-
 	return 0;
 }
 
@@ -597,8 +565,6 @@ int board_late_init(void)
 #ifdef CONFIG_CMD_BMODE
 	add_board_boot_modes(board_boot_modes);
 #endif
-	pfuze_init();
-
 	return 0;
 }
 
-- 
1.7.4.1

[U-Boot] [PATCH v3 4/5] imx: mx6sxsabresd: Use the pfuze common init function

[Ye.Li]

Modify the pfuze init for mx6sxsabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.

Signed-off-by: Ye.Li <B37916@freescale.com>
---
Changes since v1:
- Change to use pfuze common init function for sabre boards.

Changes since v2:
- Move the pfuze init to power_init_board

 board/freescale/mx6sxsabresd/mx6sxsabresd.c |   48 ++++-----------------------
 1 files changed, 7 insertions(+), 41 deletions(-)

diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 68d3718..54c84ed 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -25,6 +25,7 @@
 #include <netdev.h>
 #include <power/pmic.h>
 #include <power/pfuze100_pmic.h>
+#include "../common/pfuze.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -170,52 +171,19 @@ static struct i2c_pads_info i2c_pad_info1 = {
 	},
 };
 
-static int pfuze_init(void)
+int power_init_board(void)
 {
 	struct pmic *p;
-	int ret;
 	unsigned int reg;
 
-	ret = power_pfuze100_init(I2C_PMIC);
-	if (ret)
-		return ret;
-
-	p = pmic_get("PFUZE100");
-	ret = pmic_probe(p);
-	if (ret)
-		return ret;
-
-	pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
-	printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
-
-	/* Set SW1AB standby voltage to 0.975V */
-	pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
-	reg &= ~0x3f;
-	reg |= 0x1b;
-	pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
-
-	/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
-	pmic_reg_read(p, PUZE_100_SW1ABCONF, &reg);
-	reg &= ~0xc0;
-	reg |= 0x40;
-	pmic_reg_write(p, PUZE_100_SW1ABCONF, reg);
-
-	/* Set SW1C standby voltage to 0.975V */
-	pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
-	reg &= ~0x3f;
-	reg |= 0x1b;
-	pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
-
-	/* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
-	pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
-	reg &= ~0xc0;
-	reg |= 0x40;
-	pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
+	p = pfuze_common_init(I2C_PMIC);
+	if (!p)
+		return -ENODEV;
 
 	/* Enable power of VGEN5 3V3, needed for SD3 */
 	pmic_reg_read(p, PFUZE100_VGEN5VOL, &reg);
-	reg &= ~0x1F;
-	reg |= 0x1F;
+	reg &= ~LDO_VOL_MASK;
+	reg |= (LDOB_3_30V | (1 << LDO_EN));
 	pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
 
 	return 0;
@@ -282,8 +250,6 @@ int board_init(void)
 
 int board_late_init(void)
 {
-	pfuze_init();
-
 	return 0;
 }
 
-- 
1.7.4.1

[U-Boot] [PATCH v3 5/5] imx: imx6q/dlsabreauto: Add PMIC Pfuze100 support

[Ye.Li]

Add the pfuze100 initialization in power_init_board for imx6q/dl
sabreauto board.

Signed-off-by: Ye.Li <B37916@freescale.com>
---
Changes since v1:
- Change to use pfuze common init function for sabre boards.

Changes since v2:
- Move the pfuze init to power_init_board

 board/freescale/mx6qsabreauto/mx6qsabreauto.c |   15 +++++++++++++++
 include/configs/mx6qsabreauto.h               |    6 ++++++
 2 files changed, 21 insertions(+), 0 deletions(-)

diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index 42ae6fa..182625c 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -28,6 +28,8 @@
 #include <asm/imx-common/video.h>
 #include <asm/arch/crm_regs.h>
 #include <pca953x.h>
+#include <power/pmic.h>
+#include "../common/pfuze.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -48,6 +50,8 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
 
+#define I2C_PMIC	1
+
 int dram_init(void)
 {
 	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
@@ -364,6 +368,17 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs)
 }
 #endif
 
+int power_init_board(void)
+{
+	struct pmic *p;
+
+	p = pfuze_common_init(I2C_PMIC);
+	if (!p)
+		return -ENODEV;
+
+	return 0;
+}
+
 #ifdef CONFIG_CMD_BMODE
 static const struct boot_mode board_boot_modes[] = {
 	/* 4 bit bus width */
diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h
index 235dd6d..91161fa 100644
--- a/include/configs/mx6qsabreauto.h
+++ b/include/configs/mx6qsabreauto.h
@@ -48,4 +48,10 @@
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_SPEED		100000
 
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
+
 #endif                         /* __MX6QSABREAUTO_CONFIG_H */
-- 
1.7.4.1

[U-Boot] [PATCH v3 1/5] power: pfuze100: Update definitions for buck regulators

[Przemyslaw Marczak]

Hello Ye Li,

On 11/06/2014 09:28 AM, Ye.Li wrote:
> Add definitions for buck regulators (SW1A/B/C) registers and voltage
> values.
>
> Signed-off-by: Ye.Li <B37916@freescale.com>
> ---
> Changes since v1:
> - None
>
> Changes since v2:
> - Create this patch for updating registers definitions and magic value.
>
>   include/power/pfuze100_pmic.h |   80 +++++++++++++++++++++++++++++++++++++++++
>   1 files changed, 80 insertions(+), 0 deletions(-)
>
> diff --git a/include/power/pfuze100_pmic.h b/include/power/pfuze100_pmic.h
> index 0002f1e..1118489 100644
> --- a/include/power/pfuze100_pmic.h
> +++ b/include/power/pfuze100_pmic.h
> @@ -38,6 +38,86 @@ enum {
>   };
>
>   /*
> + * Buck Regulators
> + */
> +
> +/* SW1A/B/C Output Voltage Configuration */
> +#define SW1x_0_300V 0
> +#define SW1x_0_325V 1
> +#define SW1x_0_350V 2
> +#define SW1x_0_375V 3
> +#define SW1x_0_400V 4
> +#define SW1x_0_425V 5
> +#define SW1x_0_450V 6
> +#define SW1x_0_475V 7
> +#define SW1x_0_500V 8
> +#define SW1x_0_525V 9
> +#define SW1x_0_550V 10
> +#define SW1x_0_575V 11
> +#define SW1x_0_600V 12
> +#define SW1x_0_625V 13
> +#define SW1x_0_650V 14
> +#define SW1x_0_675V 15
> +#define SW1x_0_700V 16
> +#define SW1x_0_725V 17
> +#define SW1x_0_750V 18
> +#define SW1x_0_775V 19
> +#define SW1x_0_800V 20
> +#define SW1x_0_825V 21
> +#define SW1x_0_850V 22
> +#define SW1x_0_875V 23
> +#define SW1x_0_900V 24
> +#define SW1x_0_925V 25
> +#define SW1x_0_950V 26
> +#define SW1x_0_975V 27
> +#define SW1x_1_000V 28
> +#define SW1x_1_025V 29
> +#define SW1x_1_050V 30
> +#define SW1x_1_075V 31
> +#define SW1x_1_100V 32
> +#define SW1x_1_125V 33
> +#define SW1x_1_150V 34
> +#define SW1x_1_175V 35
> +#define SW1x_1_200V 36
> +#define SW1x_1_225V 37
> +#define SW1x_1_250V 38
> +#define SW1x_1_275V 39
> +#define SW1x_1_300V 40
> +#define SW1x_1_325V 41
> +#define SW1x_1_350V 42
> +#define SW1x_1_375V 43
> +#define SW1x_1_400V 44
> +#define SW1x_1_425V 45
> +#define SW1x_1_450V 46
> +#define SW1x_1_475V 47
> +#define SW1x_1_500V 48
> +#define SW1x_1_525V 49
> +#define SW1x_1_550V 50
> +#define SW1x_1_575V 51
> +#define SW1x_1_600V 52
> +#define SW1x_1_625V 53
> +#define SW1x_1_650V 54
> +#define SW1x_1_675V 55
> +#define SW1x_1_700V 56
> +#define SW1x_1_725V 57
> +#define SW1x_1_750V 58
> +#define SW1x_1_775V 59
> +#define SW1x_1_800V 60
> +#define SW1x_1_825V 61
> +#define SW1x_1_850V 62
> +#define SW1x_1_875V 63
> +
> +#define SW1x_NORMAL_MASK  0x3f
> +#define SW1x_STBY_MASK    0x3f
> +#define SW1x_OFF_MASK     0x3f
> +
> +#define SW1xCONF_DVSSPEED_MASK 0xc0
> +#define SW1xCONF_DVSSPEED_2US  0x00
> +#define SW1xCONF_DVSSPEED_4US  0x40
> +#define SW1xCONF_DVSSPEED_8US  0x80
> +#define SW1xCONF_DVSSPEED_16US 0xc0
> +
> +/*
>    * LDO Configuration
>    */
>
>

I can't test this code, but the changes looks good for me.

Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>

Best regards,
-- 
Przemyslaw Marczak
Samsung R&D Institute Poland
Samsung Electronics
p.marczak at samsung.com

[U-Boot] [PATCH v3 1/5] power: pfuze100: Update definitions for buck regulators

[Stefano Babic]

Hi Przemyslaw,

On 13/11/2014 17:29, Przemyslaw Marczak wrote:
> Hello Ye Li,
> 
> On 11/06/2014 09:28 AM, Ye.Li wrote:
>> Add definitions for buck regulators (SW1A/B/C) registers and voltage
>> values.
>>
>> Signed-off-by: Ye.Li <B37916@freescale.com>
>> ---

> 
> I can't test this code, but the changes looks good for me.
> 
> Reviewed-by: Przemyslaw Marczak <p.marczak@samsung.com>

Thanks - I will check the series for merging into u-boot-imx now (the
rest of patches are related to i.MX boards).

Best regards,
Stefano Babic


-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v3 5/5] imx: imx6q/dlsabreauto: Add PMIC Pfuze100 support

[Stefano Babic]

On 06/11/2014 09:29, Ye.Li wrote:
> Add the pfuze100 initialization in power_init_board for imx6q/dl
> sabreauto board.
> 
> Signed-off-by: Ye.Li <B37916@freescale.com>
> ---

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic



-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v3 4/5] imx: mx6sxsabresd: Use the pfuze common init function

[Stefano Babic]

On 06/11/2014 09:29, Ye.Li wrote:
> Modify the pfuze init for mx6sxsabresd to use the shared
> "pfuze_common_init" function. And move this initialization to
> power_init_board.
> 
> Signed-off-by: Ye.Li <B37916@freescale.com>
> ---

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic



-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v3 3/5] imx: mx6sabresd: Use the pfuze common init function

[Stefano Babic]

On 06/11/2014 09:29, Ye.Li wrote:
> Modify the pfuze init for mx6sabresd to use the shared
> "pfuze_common_init" function. And move this initialization to
> power_init_board.
> 
> Signed-off-by: Ye.Li <B37916@freescale.com>
> ---

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic


-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v3 1/5] power: pfuze100: Update definitions for buck regulators

[Stefano Babic]

On 06/11/2014 09:28, Ye.Li wrote:
> Add definitions for buck regulators (SW1A/B/C) registers and voltage
> values.
> 
> Signed-off-by: Ye.Li <B37916@freescale.com>
> ---

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic



-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================

[U-Boot] [PATCH v3 2/5] imx: mx6sabre common: Factorize the Pfuze init function

[Stefano Babic]

On 06/11/2014 09:28, Ye.Li wrote:
> Since the Pfuze initializations are similar on various mx6 SABRE
> boards. Factorize the initialization to a common function in file
> board/freescale/common/pfuze.c. So that all SABRE boards BSP can
> share the function.
> 
> Signed-off-by: Ye.Li <B37916@freescale.com>
> ---

After rebasing on current u-boot-imx and fixing the following checkpatch
errors:

ERROR: "foo * bar" should be "foo *bar"
#182: FILE: board/freescale/common/pfuze.c:11:
+struct pmic * pfuze_common_init(unsigned char i2cbus)

ERROR: "foo * bar" should be "foo *bar"
#241: FILE: board/freescale/common/pfuze.h:10:
+struct pmic * pfuze_common_init(unsigned char i2cbus);

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic



-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================