[U-Boot] [PATCH 08/18] exynos5: config: prepare for dm i2c support

[Przemyslaw Marczak <p.marczak@samsung.com>]

+ fixed address to Sjoerd Simons.

On 01/12/2015 10:19 AM, Przemyslaw Marczak wrote:
> Hello Akshay,
>
> On 01/09/2015 10:21 AM, Akshay Saraswat wrote:
>> Hi Przemyslaw,
>>
>>> This commit allows for test i2c drivers with new i2c api
>>> on Exynos5xxx based boards.
>>>
>>> The S3C24X0 I2C driver supports driver model I2C api,
>>> but i2c peripherials drivers on exynos5 boards doesn't.
>>> So this commit allows for test ported driver before switch
>>> the Exynos5 boards to DM I2C at all.
>>>
>>> Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
>>> Cc: Akshay Saraswat <akshay.s@samsung.com>
>>> Cc: Simon Glass <sjg@chromium.org>
>>> Cc: Minkyu Kang <mk7.kang@samsung.com>
>>> ---
>>> include/configs/exynos5-common.h | 29 ++++++++++++++++++-----------
>>> 1 file changed, 18 insertions(+), 11 deletions(-)
>>>
>>> diff --git a/include/configs/exynos5-common.h
>>> b/include/configs/exynos5-common.h
>>> index ad63f3c..b7af8a5 100644
>>> --- a/include/configs/exynos5-common.h
>>> +++ b/include/configs/exynos5-common.h
>>> @@ -54,13 +54,6 @@
>>> #define CONFIG_CMD_DTT
>>> #define CONFIG_TMU_CMD_DTT
>>>
>>> -/* TPM */
>>> -#define CONFIG_TPM
>>> -#define CONFIG_CMD_TPM
>>> -#define CONFIG_TPM_TIS_I2C
>>> -#define CONFIG_TPM_TIS_I2C_BUS_NUMBER    3
>>> -#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR    0x20
>>> -
>>> /* MMC SPL */
>>> #define COPY_BL2_FNPTR_ADDR    0x02020030
>>> #define CONFIG_SUPPORT_EMMC_BOOT
>>> @@ -126,15 +119,29 @@
>>> #define SPI_FLASH_UBOOT_POS    (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
>>>
>>> /* I2C */
>>> -#define CONFIG_SYS_I2C_INIT_BOARD
>>> -#define CONFIG_SYS_I2C
>>> +#if 0 /* For test */
>>
>> Quick test over SMDK 5250 after replacing #if 0 -> 1.
>> Looks like there is some problem in changing bus beyond 7.
>> Please check.
>>
>> Console prints are as follows -
>>
>> SMDK5250 # i2c dev 8
>> Setting bus to 8
>> Failure changing bus number (-19)
>> exit not allowed from main input shell.
>>
> I think that this is right, because, the defined buses are:
> - exynos5.dtsi - 0, 1, 2, 3 (periph_id: 56, 57, 58, 59),
> - exynos5250.dtsi - 4, 5, 6, 7 (periph_id: 60, 61, 62, 63)
> but there are no additional i2c nodes in exynos5250-smdk5250.dts file.
> So, you can use only i2c bus <0:7>.
>
> The additional i2c bus nodes are defined in:
> - exynos54xx.dtsi - 8, 9, 10 (periph_id: 87, 88, 203),
> So for exynos54xx boards we can switch between i2c <0:10>.
>
>>> +#define CONFIG_DM_I2C
>>> +#endif
>>> #define CONFIG_CMD_I2C
>>> -#define CONFIG_SYS_I2C_S3C24X0_SPEED    100000        /* 100 Kbps */
>>> #define CONFIG_SYS_I2C_S3C24X0
>>> -#define CONFIG_I2C_MULTI_BUS
>>> +#define CONFIG_SYS_I2C_S3C24X0_SPEED    100000        /* 100 Kbps */
>>> #define CONFIG_SYS_I2C_S3C24X0_SLAVE    0x0
>>> +#ifndef CONFIG_DM_I2C
>>> +#define CONFIG_SYS_I2C_INIT_BOARD
>>> +#define CONFIG_SYS_I2C
>>> +#define CONFIG_I2C_MULTI_BUS
>>> +#endif /* ifndef CONFIG_DM_I2C */
>>> #define CONFIG_I2C_EDID
>>>
>>> +/* TPM */
>>> +#ifndef CONFIG_DM_I2C
>>> +#define CONFIG_TPM
>>> +#define CONFIG_CMD_TPM
>>> +#define CONFIG_TPM_TIS_I2C
>>> +#define CONFIG_TPM_TIS_I2C_BUS_NUMBER    3
>>> +#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR    0x20
>>> +#endif
>>> +
>>> /* SPI */
>>> #ifdef CONFIG_SPI_FLASH
>>> #define CONFIG_EXYNOS_SPI
>>> --
>>> 1.9.1
>>
>> Regards,
>> Akshay Saraswat
>>
> So if you would like to use i2c 8, then please add proper nodes to dts -
> but please notice that the "reg" addresses are different for 5250/54xx.
>
> Best regards,

Best regards,
-- 
Przemyslaw Marczak
Samsung R&D Institute Poland
Samsung Electronics
p.marczak at samsung.com