[U-Boot] [U-boot][PATCH v2] keystone2: add support for UART download

[Nishanth Menon <nm@ti.com>]

On 02/17/2015 10:39 AM, Vitaly Andrianov wrote:
> Currently to flash u-boot image onto NAND or SPI NOR flash, very first
> time user need to use Code Composer Studio (CCS). This is cumbersome for
> an user not familiar with CCS. This patch add simpler procedure using
> uart boot mode for K2 EVMs.
> 
> When UART bootmode is set and board is rebooted, the ROM boot loader
> transfers the image at the beginning of the internal RAM. After the
> transfer is complete the boot-loader sets the PC to the first internal RAM
> address 0x0c000000. The u-boot.bin is linked to the address 0x0c001000.
> 
> In order to use the u-boot.bin as an image for UART download, we need to
> add 4K zeros prefix that act as 1K NOP instructions before reaching
> 0xc001000.
> 
> Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
> Acked-by: Murali Karicheri <m-karicheri2@ti.com>
> Tested-by: Murali Karicheri <m-karicheri2@ti.com>
> ---
> Changes in V2:
> 	- removed extra EOL
> 	- "MSMC" replaced by "internal RAM" in the commit message
> 
>  Makefile                |  6 ++++++
>  board/ti/ks2_evm/README | 15 +++++++++++++++
>  2 files changed, 21 insertions(+)
> 
> diff --git a/Makefile b/Makefile
> index 36a9a28..7a86cac 100644
> --- a/Makefile
> +++ b/Makefile
> @@ -940,6 +940,12 @@ u-boot-nand.gph: u-boot.bin FORCE
>  	$(call if_changed,mkimage)
>  	@dd if=/dev/zero bs=8 count=1 2>/dev/null >> $@
>  
> +u-boot.uart.pad:
> +	@dd if=/dev/zero bs=4 count=1024 2>/dev/null > $@
> +
> +u-boot.uart: u-boot.uart.pad u-boot.bin FORCE
> +	$(call if_changed,cat)
> +
>  # x86 uses a large ROM. We fill it with 0xff, put the 16-bit stuff (including
>  # reset vector) at the top, Intel ME descriptor at the bottom, and U-Boot in
>  # the middle.
> diff --git a/board/ti/ks2_evm/README b/board/ti/ks2_evm/README
> index 9ee90a4..7e2e096 100644
> --- a/board/ti/ks2_evm/README
> +++ b/board/ti/ks2_evm/README
> @@ -81,6 +81,21 @@ To build u-boot-nand.gph
>    >make k2hk_evm_defconfig
>    >make u-boot-nand.gph
>  
> +To build u-boot.uart
> +  >make k2hk_evm_defconfig
> +  >make u-boot.uart
> +
> +Load and Run U-Boot on keystone EVMs using UART download
> +========================================================
> +
> +Open BMC and regular UART terminals.
> +
> +1. On the regular UART port start xmodem transfer of the u-boot.uart
> +2. Using BMC terminal set the ARM-UART bootmode and reboot the EVM
> +   BMC> bootmode #4
> +   MBC> reboot
> +3. When xmodem is complete you should see the u-boot starts on the UART port
> +
>  Load and Run U-Boot on keystone EVMs using CCS
>  =========================================
>  
> 

Could you please address the comments provided in V1 of your patch first?
https://patchwork.ozlabs.org/patch/440322/

I see my comments have not been responded to as to why the
alternatives presented do not work.

It is always a good practice to respond to review comments prior to
posting a new revision and not just ignoring them.

Sorry, I have to give a: Nak to this version of patch considering that
there are still questions not addressed from V1.

-- 
Regards,
Nishanth Menon