[U-Boot] [PATCH] arm: mx6: ddr: add pd_fast_exit flag to system information

[U-Boot] [PATCH] arm: mx6: ddr: add pd_fast_exit flag to system information

[Tim Harvey]

DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.

In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
 arch/arm/cpu/armv7/mx6/ddr.c            | 7 ++++++-
 arch/arm/include/asm/arch-mx6/mx6-ddr.h | 1 +
 2 files changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/arm/cpu/armv7/mx6/ddr.c b/arch/arm/cpu/armv7/mx6/ddr.c
index fef2231..653d58e 100644
--- a/arch/arm/cpu/armv7/mx6/ddr.c
+++ b/arch/arm/cpu/armv7/mx6/ddr.c
@@ -514,17 +514,21 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo *sysinfo,
 		/* MR2 */
 		val = (sysinfo->rtt_wr & 3) << 9 | (ddr3_cfg->SRT & 1) << 7 |
 		      ((tcwl - 3) & 3) << 3;
+		debug("MR2 CS%d: 0x%08x\n", cs, (u32)MR(val, 2, 3, cs));
 		mmdc0->mdscr = MR(val, 2, 3, cs);
 		/* MR3 */
+		debug("MR3 CS%d: 0x%08x\n", cs, (u32)MR(0, 3, 3, cs));
 		mmdc0->mdscr = MR(0, 3, 3, cs);
 		/* MR1 */
 		val = ((sysinfo->rtt_nom & 1) ? 1 : 0) << 2 |
 		      ((sysinfo->rtt_nom & 2) ? 1 : 0) << 6;
+		debug("MR1 CS%d: 0x%08x\n", cs, (u32)MR(val, 1, 3, cs));
 		mmdc0->mdscr = MR(val, 1, 3, cs);
 		/* MR0 */
 		val = ((tcl - 1) << 4) |	/* CAS */
 		      (1 << 8)   |		/* DLL Reset */
 		      ((twr - 3) << 9);		/* Write Recovery */
+		debug("MR0 CS%d: 0x%08x\n", cs, (u32)MR(val, 0, 3, cs));
 		mmdc0->mdscr = MR(val, 0, 3, cs);
 		/* ZQ calibration */
 		val = (1 << 10);
@@ -535,10 +539,11 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo *sysinfo,
 	mmdc0->mdpdc = (tcke & 0x7) << 16 |
 			5            << 12 |  /* PWDT_1: 256 cycles */
 			5            <<  8 |  /* PWDT_0: 256 cycles */
-			1            <<  7 |  /* SLOW_PD */
 			1            <<  6 |  /* BOTH_CS_PD */
 			(tcksrx & 0x7) << 3 |
 			(tcksre & 0x7);
+	if (!sysinfo->pd_fast_exit)
+		mmdc0->mdpdc |= (1 << 7); /* SLOW_PD */
 	mmdc0->mapsr = 0x00001006; /* ADOPT power down enabled */
 
 	/* Step 11: Configure ZQ calibration: one-time and periodic 1ms */
diff --git a/arch/arm/include/asm/arch-mx6/mx6-ddr.h b/arch/arm/include/asm/arch-mx6/mx6-ddr.h
index 8e0d7d1..c49aa62 100644
--- a/arch/arm/include/asm/arch-mx6/mx6-ddr.h
+++ b/arch/arm/include/asm/arch-mx6/mx6-ddr.h
@@ -250,6 +250,7 @@ struct mx6_ddr_sysinfo {
 	u8 mif3_mode;	/* Command prediction working mode */
 	u8 rst_to_cke;	/* Time from SDE enable to CKE rise */
 	u8 sde_to_rst;	/* Time from SDE enable until DDR reset# is high */
+	u8 pd_fast_exit;/* enable precharge powerdown fast-exit */
 };
 
 /*
-- 
1.9.1

[U-Boot] [PATCH] arm: mx6: ddr: add pd_fast_exit flag to system information

[Stefano Babic]

On 04/04/2015 01:52, Tim Harvey wrote:
> DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
> 
> In slow-exit mode the DLL is off but in some quiescent state that makes it easy
> to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
> In fast-exist mode the DLL is maintained such that it is ready again in about
> 3tCK.
> 
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> ---

Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic


-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================