From mboxrd@z Thu Jan  1 00:00:00 1970
From: Stefano Babic <sbabic@denx.de>
Date: Wed, 22 Apr 2015 14:47:42 +0200
Subject: [U-Boot] [RFC PATCH] arm: mx6: Clamp MMDC and DDR3 clocks for
	timing calculations
In-Reply-To: <55379271.10501@mail.bg>
References: <1429223817-10076-1-git-send-email-picmaster@mail.bg>
 <5537901B.8050106@denx.de> <55379271.10501@mail.bg>
Message-ID: <5537986E.2000101@denx.de>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

On 22/04/2015 14:22, Nikolay Dimitrov wrote:
> Hi Stefano,
> 
> On 04/22/2015 03:12 PM, Stefano Babic wrote:
>> Hi Nikolay,
>>
>> On 17/04/2015 00:36, Nikolay Dimitrov wrote:
>>> This is proposal for clamping the MMDC/DDR3 clocks to the maximum
>>> supported
>>> frequencies as per imx6 SOC models, and for dynamically calculating
>>> valid
>>> clock value based on mem_speed.
>>>
>>> Currently the code uses impossible values for mem_speed (1333, 1600
>>> MT/s) for
>>> calculating the DDR timings, and uses fixed clock (528 or 400 MHz) which
>>> doesn't take into account DDR3 memory limitations.
>>>
>>> Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
>>> Cc: Fabio Estevam <festevam@gmail.com>
>>> Cc: Stefano Babic <sbabic@denx.de>
>>> Cc: Tim Harvey <tharvey@gateworks.com>
>>> Cc: Eric Nelson <eric.nelson@boundarydevices.com>
>>> ---
>>>   arch/arm/cpu/armv7/mx6/ddr.c |   25 ++++++++++++++++++++-----
>>>   1 file changed, 20 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/arch/arm/cpu/armv7/mx6/ddr.c b/arch/arm/cpu/armv7/mx6/ddr.c
>>> index fef2231..9daa180 100644
>>> --- a/arch/arm/cpu/armv7/mx6/ddr.c
>>> +++ b/arch/arm/cpu/armv7/mx6/ddr.c
>>> @@ -265,7 +265,7 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo
>>> *sysinfo,
>>>       u16 tdllk = 0x1ff; /* DLL locking time: 512 cycles (JEDEC DDR3) */
>>>       u8 coladdr;
>>>       int clkper; /* clock period in picoseconds */
>>> -    int clock; /* clock freq in mHz */
>>> +    int clock; /* clock freq in MHz */
>>>       int cs;
>>>
>>>       mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
>>> @@ -273,16 +273,31 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo
>>> *sysinfo,
>>>       mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
>>>   #endif
>>>
>>> -    /* MX6D/MX6Q: 1066 MHz memory clock, clkper = 1.894ns = 1894ps */
>>> +    /* Limit mem_speed for MX6D/MX6Q */
>>>       if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) {
>>> -        clock = 528;
>>> +        if (ddr3_cfg->mem_speed > 1066)
>>> +            ddr3_cfg->mem_speed = 1066; /* 1066 MT/s */
>>> +
>>>           tcwl = 4;
>>>       }
>>> -    /* MX6S/MX6DL: 800 MHz memory clock, clkper = 2.5ns = 2500ps */
>>> +    /* Limit mem_speed for MX6S/MX6DL */
>>>       else {
>>> -        clock = 400;
>>> +        if (ddr3_cfg->mem_speed > 800)
>>> +            ddr3_cfg->mem_speed = 800;  /* 800 MT/s */
>>> +
>>>           tcwl = 3;
>>>       }
>>> +
>>> +    clock = ddr3_cfg->mem_speed / 2;
>>> +    /*
>>> +     * Data rate of 1066 MT/s requires 533 MHz DDR3 clock, but
>>> MX6D/Q supports
>>> +     * up to 528 MHz, so reduce the clock to fit chip specs
>>> +     */
>>> +    if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) {
>>> +        if (clock > 528)
>>> +            clock = 528; /* 528 MHz */
>>> +    }
>>> +
>>>       clkper = (1000 * 1000) / clock; /* pico seconds */
>>>       todtlon = tcwl;
>>>       taxpd = tcwl;
>>>
>>
>> Well done. I think we can forget the RFC of the title and apply it.
> 
> Do you need me to reword the commit message?

No, I check myself, thanks.

Regards,
Stefano


-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================