public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
* [U-Boot] [PATCH v3] arm, imx6: add support for aristainetos2 board
@ 2015-05-18 11:32 Heiko Schocher
  2015-05-26 12:20 ` Stefano Babic
  0 siblings, 1 reply; 2+ messages in thread
From: Heiko Schocher @ 2015-05-18 11:32 UTC (permalink / raw)
  To: u-boot

add support for imx6dl based aristainetos2 board

U-Boot 2015.04-rc5-00066-g60f6ed4 (Apr 10 2015 - 08:46:27)

CPU:   Freescale i.MX6DL rev1.1 at 792 MHz
Reset cause: WDOG
Board: aristaitenos2
       Watchdog enabled
I2C:   ready
DRAM:  1 GiB
NAND:  1024 MiB
MMC:   FSL_SDHC: 0
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lg4573 (480x800)
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
=>

Signed-off-by: Heiko Schocher <hs@denx.de>

---

Changes in v2:
- add comment from Stefano Babic:
  - adapt for i2c fixes suggested by Stefano Babic
  - remove lgdisplay var
  - remove CONFIG_PHY_MICREL_KSZ9031
  - rename enable_spi to enable_spi_display
  - rotate logo remains in board code
Changes in v3:
- add comment from Stefano Babic:
  merged aristainetos2 board with the aristainetos board support
  introduced a include/configs/aristainetos-common.h for common
  settings, board/aristainetos/aristainetos-v1.c and
  board/aristainetos/aristainetos-v2.c for board version specific
  settings

 arch/arm/Kconfig                      |   4 +
 board/aristainetos/Kconfig            |  13 +
 board/aristainetos/MAINTAINERS        |   2 +
 board/aristainetos/aristainetos-v1.c  | 279 +++++++++++++++
 board/aristainetos/aristainetos-v2.c  | 627 ++++++++++++++++++++++++++++++++++
 board/aristainetos/aristainetos.c     | 323 ++++--------------
 board/aristainetos/aristainetos2.cfg  |  34 ++
 board/aristainetos/axi.cfg            |  22 ++
 board/aristainetos/clocks2.cfg        |  24 ++
 board/aristainetos/ddr-setup2.cfg     |  59 ++++
 board/aristainetos/nt5cc256m16cp.cfg  |  60 ++++
 configs/aristainetos2_defconfig       |   3 +
 include/configs/aristainetos-common.h | 333 ++++++++++++++++++
 include/configs/aristainetos.h        | 314 +----------------
 include/configs/aristainetos2.h       |  56 +++
 15 files changed, 1585 insertions(+), 568 deletions(-)
 create mode 100644 board/aristainetos/aristainetos-v1.c
 create mode 100644 board/aristainetos/aristainetos-v2.c
 create mode 100644 board/aristainetos/aristainetos2.cfg
 create mode 100644 board/aristainetos/axi.cfg
 create mode 100644 board/aristainetos/clocks2.cfg
 create mode 100644 board/aristainetos/ddr-setup2.cfg
 create mode 100644 board/aristainetos/nt5cc256m16cp.cfg
 create mode 100644 configs/aristainetos2_defconfig
 create mode 100644 include/configs/aristainetos-common.h
 create mode 100644 include/configs/aristainetos2.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 6727423..c5adb11 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -524,6 +524,10 @@ config TARGET_ARISTAINETOS
 	bool "Support aristainetos"
 	select CPU_V7
 
+config TARGET_ARISTAINETOS2
+	bool "Support aristainetos2"
+	select CPU_V7
+
 config TARGET_MX6QARM2
 	bool "Support mx6qarm2"
 	select CPU_V7
diff --git a/board/aristainetos/Kconfig b/board/aristainetos/Kconfig
index b8e380e..500b665 100644
--- a/board/aristainetos/Kconfig
+++ b/board/aristainetos/Kconfig
@@ -10,3 +10,16 @@ config SYS_CONFIG_NAME
 	default "aristainetos"
 
 endif
+
+if TARGET_ARISTAINETOS2
+
+config SYS_BOARD
+	default "aristainetos"
+
+config SYS_SOC
+	default "mx6"
+
+config SYS_CONFIG_NAME
+	default "aristainetos2"
+
+endif
diff --git a/board/aristainetos/MAINTAINERS b/board/aristainetos/MAINTAINERS
index d45d423..78c9b69 100644
--- a/board/aristainetos/MAINTAINERS
+++ b/board/aristainetos/MAINTAINERS
@@ -4,3 +4,5 @@ S:	Maintained
 F:	board/aristainetos/
 F:	include/configs/aristainetos.h
 F:	configs/aristainetos_defconfig
+F:	include/configs/aristainetos2.h
+F:	configs/aristainetos2_defconfig
diff --git a/board/aristainetos/aristainetos-v1.c b/board/aristainetos/aristainetos-v1.c
new file mode 100644
index 0000000..d6a7614
--- /dev/null
+++ b/board/aristainetos/aristainetos-v1.c
@@ -0,0 +1,279 @@
+/*
+ * (C) Copyright 2015
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <pwm.h>
+
+struct i2c_pads_info i2c_pad_info3 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
+		.gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
+		.gp = IMX_GPIO_NR(3, 17)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
+		.gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
+		.gp = IMX_GPIO_NR(3, 18)
+	}
+};
+
+iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart5_pads[] = {
+	MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const gpio_pads[] = {
+	/* LED enable */
+	MX6_PAD_SD4_DAT5__GPIO2_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* spi flash WP protect */
+	MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* backlight enable */
+	MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED yellow */
+	MX6_PAD_GPIO_3__GPIO1_IO03 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED red */
+	MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED green */
+	MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED blue */
+	MX6_PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* i2c4 scl */
+	MX6_PAD_GPIO_7__GPIO1_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* i2c4 sda */
+	MX6_PAD_GPIO_8__GPIO1_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* spi CS 1 */
+	MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const misc_pads[] = {
+	MX6_PAD_GPIO_1__USB_OTG_ID		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* OTG Power enable */
+	MX6_PAD_EIM_D31__GPIO3_IO31		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_KEY_ROW4__GPIO4_IO15		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_GPIO_16__ENET_REF_CLK	| MUX_PAD_CTRL(0x4001b0a8),
+	MX6_PAD_ENET_MDIO__ENET_MDIO	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_TX_EN__ENET_TX_EN	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RX_ER__ENET_RX_ER	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_CRS_DV__ENET_RX_EN	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+	/* set GPIO_16 as ENET_REF_CLK_OUT */
+	setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
+}
+
+static iomux_v3_cfg_t const backlight_pads[] = {
+	MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__PWM3_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const ecspi4_pads[] = {
+	MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const display_pads[] = {
+	MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL),
+	MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15,
+	MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02,
+	MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03,
+	MX6_PAD_DI0_PIN4__GPIO4_IO20,
+	MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
+	MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
+	MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
+	MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
+	MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
+	MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
+	MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
+	MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
+	MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
+	MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
+	MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
+	MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
+	MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
+	MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
+	MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
+	MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
+	MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
+	MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
+	MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18,
+	MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19,
+	MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20,
+	MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21,
+	MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22,
+	MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23,
+};
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
+		? (IMX_GPIO_NR(3, 20)) : -1;
+}
+
+static void setup_spi(void)
+{
+	int i;
+
+	imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
+	for (i = 0; i < 3; i++)
+		enable_spi_clk(true, i);
+
+	/* set cs1 to high */
+	gpio_direction_output(ECSPI4_CS1, 1);
+}
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+}
+
+int board_eth_init(bd_t *bis)
+{
+	struct iomuxc *iomuxc_regs =
+				(struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	/* clear gpr1[14], gpr1[18:17] to select anatop clock */
+	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0);
+
+	ret = enable_fec_anatop_clock(ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	setup_iomux_enet();
+	return cpu_eth_init(bis);
+}
+
+static void enable_lvds(struct display_info_t const *dev)
+{
+	imx_iomux_v3_setup_multiple_pads(
+		display_pads,
+		 ARRAY_SIZE(display_pads));
+	imx_iomux_v3_setup_multiple_pads(
+		backlight_pads,
+		 ARRAY_SIZE(backlight_pads));
+
+	/* enable backlight PWM 3 */
+	if (pwm_init(2, 0, 0))
+		goto error;
+	/* duty cycle 500ns, period: 3000ns */
+	if (pwm_config(2, 500, 3000))
+		goto error;
+	if (pwm_enable(2))
+		goto error;
+	return;
+
+error:
+	puts("error init pwm for backlight\n");
+	return;
+}
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+
+	reg = readl(&mxc_ccm->cs2cdr);
+	/* select pll 5 clock */
+	reg &= MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK;
+	reg &= MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK;
+	writel(reg, &mxc_ccm->cs2cdr);
+
+	imx_iomux_v3_setup_multiple_pads(backlight_pads,
+					 ARRAY_SIZE(backlight_pads));
+}
+
+static void setup_iomux_gpio(void)
+{
+	imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads));
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	setup_iomux_gpio();
+
+	setup_display();
+	return 0;
+}
+
+
+static void setup_i2c4(void)
+{
+	/* i2c4 not used, set it to gpio input */
+	gpio_request(IMX_GPIO_NR(1, 7), "i2c4_scl");
+	gpio_direction_input(IMX_GPIO_NR(1, 7));
+	gpio_request(IMX_GPIO_NR(1, 8), "i2c4_sda");
+	gpio_direction_input(IMX_GPIO_NR(1, 8));
+}
+
+static void setup_board_gpio(void)
+{
+	/* enable LED */
+	gpio_request(IMX_GPIO_NR(2, 13), "LED ena");
+	gpio_direction_output(IMX_GPIO_NR(2, 13), 0);
+
+	gpio_request(IMX_GPIO_NR(1, 3), "LED yellow");
+	gpio_direction_output(IMX_GPIO_NR(1, 3), 1);
+	gpio_request(IMX_GPIO_NR(1, 4), "LED red");
+	gpio_direction_output(IMX_GPIO_NR(1, 4), 1);
+	gpio_request(IMX_GPIO_NR(1, 5), "LED green");
+	gpio_direction_output(IMX_GPIO_NR(1, 5), 1);
+	gpio_request(IMX_GPIO_NR(1, 6), "LED blue");
+	gpio_direction_output(IMX_GPIO_NR(1, 6), 1);
+}
+
+static void setup_board_spi(void)
+{
+}
diff --git a/board/aristainetos/aristainetos-v2.c b/board/aristainetos/aristainetos-v2.c
new file mode 100644
index 0000000..7a44031
--- /dev/null
+++ b/board/aristainetos/aristainetos-v2.c
@@ -0,0 +1,627 @@
+/*
+ * (C) Copyright 2015
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <pwm.h>
+#include <micrel.h>
+#include <spi.h>
+#include <video.h>
+#include <../drivers/video/ipu.h>
+#if defined(CONFIG_VIDEO_BMP_LOGO)
+	#include <bmp_logo.h>
+#endif
+
+#define USDHC2_PAD_CTRL (PAD_CTL_SPEED_LOW |			\
+	PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define ECSPI1_CS0		IMX_GPIO_NR(4, 9)   /* 4.3 display controller */
+#define ECSPI4_CS0		IMX_GPIO_NR(3, 29)
+#define SOFT_RESET_GPIO		IMX_GPIO_NR(7, 13)
+#define SD2_DRIVER_ENABLE	IMX_GPIO_NR(7, 8)
+
+struct i2c_pads_info i2c_pad_info3 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC,
+		.gp = IMX_GPIO_NR(1, 5)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
+		.gp = IMX_GPIO_NR(1, 6)
+	}
+};
+
+struct i2c_pads_info i2c_pad_info4 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_7__I2C4_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO_7__GPIO1_IO07 | PC,
+		.gp = IMX_GPIO_NR(1, 7)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_8__I2C4_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO_8__GPIO1_IO08 | PC,
+		.gp = IMX_GPIO_NR(1, 8)
+	}
+};
+
+iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D19__UART1_CTS_B    | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D20__UART1_RTS_B    | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart2_pads[] = {
+	MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart3_pads[] = {
+	MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const gpio_pads[] = {
+	/* LED enable*/
+	MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED yellow */
+	MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED red */
+	MX6_PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED green */
+	MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED blue */
+	MX6_PAD_EIM_EB1__GPIO2_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* spi flash WP protect */
+	MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* spi CS 0 */
+	MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* spi bus #2 SS driver enable */
+	MX6_PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* RST_LOC# PHY reset input (has pull-down!)*/
+	MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD 2 level shifter output enable */
+	MX6_PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD1 card detect input */
+	MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD1 write protect input */
+	MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD2 card detect input */
+	MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD2 write protect input */
+	MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* Touchscreen IRQ */
+	MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const misc_pads[] = {
+	/* USB_OTG_ID = GPIO1_24*/
+	MX6_PAD_ENET_RX_ER__USB_OTG_ID		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* H1 Power enable = GPIO1_0*/
+	MX6_PAD_GPIO_0__USB_H1_PWR		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* OTG Power enable = GPIO4_15*/
+	MX6_PAD_KEY_ROW4__USB_OTG_PWR		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const backlight_pads[] = {
+	/* backlight PWM brightness control */
+	MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* backlight enable */
+	MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LCD power enable */
+	MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+}
+
+iomux_v3_cfg_t const ecspi4_pads[] = {
+	MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_A25__GPIO5_IO02  | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D29__GPIO3_IO29  | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const display_pads[] = {
+	MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL),
+	MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15,
+	MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02,
+	MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03,
+	MX6_PAD_DI0_PIN4__GPIO4_IO20,
+	MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
+	MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
+	MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
+	MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
+	MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
+	MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
+	MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
+	MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
+	MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
+	MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
+	MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
+	MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
+	MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
+	MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
+	MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
+	MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
+	MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
+	MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
+	MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18,
+	MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19,
+	MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20,
+	MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21,
+	MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22,
+	MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23,
+};
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	if (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
+		return IMX_GPIO_NR(5, 2);
+
+	if (bus == 0 && cs == 0)
+		return IMX_GPIO_NR(4, 9);
+
+	return -1;
+}
+
+static void setup_spi(void)
+{
+	int i;
+
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+	imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
+	for (i = 0; i < 4; i++)
+		enable_spi_clk(true, i);
+
+	gpio_direction_output(ECSPI1_CS0, 1);
+	gpio_direction_output(ECSPI4_CS1, 0);
+
+	/* set cs0 to high (second device on spi bus #4) */
+	gpio_direction_output(ECSPI4_CS0, 1);
+}
+
+static void setup_iomux_uart(void)
+{
+	switch (CONFIG_MXC_UART_BASE) {
+	case UART1_BASE:
+		imx_iomux_v3_setup_multiple_pads(uart1_pads,
+						 ARRAY_SIZE(uart1_pads));
+		break;
+	case UART2_BASE:
+		imx_iomux_v3_setup_multiple_pads(uart2_pads,
+						 ARRAY_SIZE(uart2_pads));
+		break;
+	case UART3_BASE:
+		imx_iomux_v3_setup_multiple_pads(uart3_pads,
+						 ARRAY_SIZE(uart3_pads));
+		break;
+	case UART4_BASE:
+		imx_iomux_v3_setup_multiple_pads(uart4_pads,
+						 ARRAY_SIZE(uart4_pads));
+		break;
+	}
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* control data pad skew - devaddr = 0x02, register = 0x04 */
+	ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+	/* rx data pad skew - devaddr = 0x02, register = 0x05 */
+	ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+	/* tx data pad skew - devaddr = 0x02, register = 0x06 */
+	ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+	/* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */
+	ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+	return cpu_eth_init(bis);
+}
+
+static int rotate_logo_one(unsigned char *out, unsigned char *in)
+{
+	int   i, j;
+
+	for (i = 0; i < BMP_LOGO_WIDTH; i++)
+		for (j = 0; j < BMP_LOGO_HEIGHT; j++)
+			out[j * BMP_LOGO_WIDTH + BMP_LOGO_HEIGHT - 1 - i] =
+			in[i * BMP_LOGO_WIDTH + j];
+	return 0;
+}
+
+/*
+ * Rotate the BMP_LOGO (only)
+ * Will only work, if the logo is square, as
+ * BMP_LOGO_HEIGHT and BMP_LOGO_WIDTH are defines, not variables
+ */
+void rotate_logo(int rotations)
+{
+	unsigned char out_logo[BMP_LOGO_WIDTH * BMP_LOGO_HEIGHT];
+	unsigned char *in_logo;
+	int   i, j;
+
+	if (BMP_LOGO_WIDTH != BMP_LOGO_HEIGHT)
+		return;
+
+	in_logo = bmp_logo_bitmap;
+
+	/* one 90 degree rotation */
+	if (rotations == 1  ||  rotations == 2  ||  rotations == 3)
+		rotate_logo_one(out_logo, in_logo);
+
+	/* second 90 degree rotation */
+	if (rotations == 2  ||  rotations == 3)
+		rotate_logo_one(in_logo, out_logo);
+
+	/* third 90 degree rotation */
+	if (rotations == 3)
+		rotate_logo_one(out_logo, in_logo);
+
+	/* copy result back to original array */
+	if (rotations == 1  ||  rotations == 3)
+		for (i = 0; i < BMP_LOGO_WIDTH; i++)
+			for (j = 0; j < BMP_LOGO_HEIGHT; j++)
+				in_logo[i * BMP_LOGO_WIDTH + j] =
+				out_logo[i * BMP_LOGO_WIDTH + j];
+}
+
+static void enable_display_power(void)
+{
+	imx_iomux_v3_setup_multiple_pads(backlight_pads,
+					 ARRAY_SIZE(backlight_pads));
+
+	/* backlight enable */
+	gpio_direction_output(IMX_GPIO_NR(6, 31), 1);
+	/* LCD power enable */
+	gpio_direction_output(IMX_GPIO_NR(6, 15), 1);
+
+	/* enable backlight PWM 1 */
+	if (pwm_init(0, 0, 0))
+		goto error;
+	/* duty cycle 500ns, period: 3000ns */
+	if (pwm_config(0, 50000, 300000))
+		goto error;
+	if (pwm_enable(0))
+		goto error;
+	return;
+
+error:
+	puts("error init pwm for backlight\n");
+	return;
+}
+
+static void enable_lvds(struct display_info_t const *dev)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+	s32 timeout = 100000;
+
+	/* set PLL5 clock */
+	reg = readl(&ccm->analog_pll_video);
+	reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
+	writel(reg, &ccm->analog_pll_video);
+
+	/* set PLL5 to 232720000Hz */
+	reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x26);
+	reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
+	writel(reg, &ccm->analog_pll_video);
+
+	writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xC0238),
+	       &ccm->analog_pll_video_num);
+	writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xF4240),
+	       &ccm->analog_pll_video_denom);
+
+	reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+	writel(reg, &ccm->analog_pll_video);
+
+	while (timeout--)
+		if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+			break;
+	if (timeout < 0)
+		printf("Warning: video pll lock timeout!\n");
+
+	reg = readl(&ccm->analog_pll_video);
+	reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+	reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+	writel(reg, &ccm->analog_pll_video);
+
+	/* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
+	reg = readl(&ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+		| (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &ccm->cs2cdr);
+
+	reg = readl(&ccm->cscmr2);
+	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+	writel(reg, &ccm->cscmr2);
+
+	reg = readl(&ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	      | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+	      | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
+	      | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	      | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+	      | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+	      | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+	       | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+		  << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+
+	return;
+}
+
+static void enable_spi_display(struct display_info_t const *dev)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+	s32 timeout = 100000;
+
+#if defined(CONFIG_VIDEO_BMP_LOGO)
+	rotate_logo(3);  /* portrait display in landscape mode */
+#endif
+
+	/*
+	 * set ldb clock to 28341000 Hz calculated through the formula:
+	 * (XRES + LEFT_M + RIGHT_M + HSYNC_LEN) *
+	 * (YRES + UPPER_M + LOWER_M + VSYNC_LEN) * REFRESH)
+	 * see:
+	 * https://community.freescale.com/thread/308170
+	 */
+	ipu_set_ldb_clock(28341000);
+
+	reg = readl(&ccm->cs2cdr);
+
+	/* select pll 5 clock */
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		| MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	writel(reg, &ccm->cs2cdr);
+
+	/* set PLL5 to 197994996Hz */
+	reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x21);
+	reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
+	writel(reg, &ccm->analog_pll_video);
+
+	writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xfbf4),
+	       &ccm->analog_pll_video_num);
+	writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xf4240),
+	       &ccm->analog_pll_video_denom);
+
+	reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+	writel(reg, &ccm->analog_pll_video);
+
+	while (timeout--)
+		if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+			break;
+	if (timeout < 0)
+		printf("Warning: video pll lock timeout!\n");
+
+	reg = readl(&ccm->analog_pll_video);
+	reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+	reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+	writel(reg, &ccm->analog_pll_video);
+
+	/* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
+	reg = readl(&ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+		| (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &ccm->cs2cdr);
+
+	reg = readl(&ccm->cscmr2);
+	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+	writel(reg, &ccm->cscmr2);
+
+	reg = readl(&ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK;
+	reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET);
+	reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK;
+	reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+	writel(reg, &ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	      | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+	      | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
+	      | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	      | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+	      | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+	      | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+	       | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+		  << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+
+	imx_iomux_v3_setup_multiple_pads(
+		display_pads,
+		 ARRAY_SIZE(display_pads));
+
+	return;
+}
+static void setup_display(void)
+{
+	enable_ipu_clock();
+	enable_display_power();
+}
+
+static void setup_iomux_gpio(void)
+{
+	imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads));
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	setup_iomux_gpio();
+
+	gpio_direction_output(SOFT_RESET_GPIO, 1);
+	gpio_direction_output(SD2_DRIVER_ENABLE, 1);
+	setup_display();
+	return 0;
+}
+
+static void setup_i2c4(void)
+{
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
+		  &i2c_pad_info4);
+}
+
+static void setup_board_gpio(void)
+{
+	/* enable all LEDs */
+	gpio_request(IMX_GPIO_NR(2, 13), "LED ena"); /* 25 */
+	gpio_direction_output(IMX_GPIO_NR(1, 25), 0);
+
+	/* switch off Status LEDs */
+	gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */
+	gpio_direction_output(IMX_GPIO_NR(6, 16), 1);
+	gpio_request(IMX_GPIO_NR(2, 28), "LED red"); /* 60 */
+	gpio_direction_output(IMX_GPIO_NR(2, 28), 1);
+	gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */
+	gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
+	gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */
+	gpio_direction_output(IMX_GPIO_NR(2, 29), 1);
+}
+
+static void setup_board_spi(void)
+{
+	/* enable spi bus #2 SS drivers */
+	gpio_direction_output(IMX_GPIO_NR(6, 6), 1);
+}
+
+int board_late_init(void)
+{
+	char *my_bootdelay;
+	char bootmode = 0;
+	char const *panel = getenv("panel");
+
+	/*
+	 * Check the boot-source. If booting from NOR Flash,
+	 * disable bootdelay
+	 */
+	gpio_request(IMX_GPIO_NR(7, 6), "bootsel0");
+	gpio_direction_input(IMX_GPIO_NR(7, 6));
+	gpio_request(IMX_GPIO_NR(7, 7), "bootsel1");
+	gpio_direction_input(IMX_GPIO_NR(7, 7));
+	gpio_request(IMX_GPIO_NR(7, 1), "bootsel2");
+	gpio_direction_input(IMX_GPIO_NR(7, 1));
+	bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 6)) ? 1 : 0) << 0;
+	bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 7)) ? 1 : 0) << 1;
+	bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 1)) ? 1 : 0) << 2;
+
+	if (bootmode == 7) {
+		my_bootdelay = getenv("nor_bootdelay");
+		if (my_bootdelay != NULL)
+			setenv("bootdelay", my_bootdelay);
+		else
+			setenv("bootdelay", "-2");
+	}
+
+	/* if we have the lg panel, we can initialze it now */
+	if (panel)
+		if (!strcmp(panel, displays[1].mode.name))
+			lg4573_spi_startup(0, 0, 10000000, SPI_MODE_0);
+
+	return 0;
+}
+
diff --git a/board/aristainetos/aristainetos.c b/board/aristainetos/aristainetos.c
index 8330bb6..0c39ee6 100644
--- a/board/aristainetos/aristainetos.c
+++ b/board/aristainetos/aristainetos.c
@@ -58,6 +58,13 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define ECSPI4_CS1		IMX_GPIO_NR(5, 2)
 
+#if (CONFIG_SYS_BOARD_VERSION == 1)
+#include "./aristainetos-v1.c"
+#elif (CONFIG_SYS_BOARD_VERSION == 2)
+#include "./aristainetos-v2.c"
+#endif
+
+
 struct i2c_pads_info i2c_pad_info1 = {
 	.scl = {
 		.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC,
@@ -84,89 +91,6 @@ struct i2c_pads_info i2c_pad_info2 = {
 	}
 };
 
-struct i2c_pads_info i2c_pad_info3 = {
-	.scl = {
-		.i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
-		.gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
-		.gp = IMX_GPIO_NR(3, 17)
-	},
-	.sda = {
-		.i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
-		.gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
-		.gp = IMX_GPIO_NR(3, 18)
-	}
-};
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
-
-	return 0;
-}
-
-iomux_v3_cfg_t const uart1_pads[] = {
-	MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const uart5_pads[] = {
-	MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const gpio_pads[] = {
-	/* LED enable */
-	MX6_PAD_SD4_DAT5__GPIO2_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* spi flash WP protect */
-	MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* backlight enable */
-	MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* LED yellow */
-	MX6_PAD_GPIO_3__GPIO1_IO03 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* LED red */
-	MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* LED green */
-	MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* LED blue */
-	MX6_PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* i2c4 scl */
-	MX6_PAD_GPIO_7__GPIO1_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* i2c4 sda */
-	MX6_PAD_GPIO_8__GPIO1_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* spi CS 1 */
-	MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const misc_pads[] = {
-	MX6_PAD_GPIO_1__USB_OTG_ID		| MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* OTG Power enable */
-	MX6_PAD_EIM_D31__GPIO3_IO31		| MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_KEY_ROW4__GPIO4_IO15		| MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const enet_pads[] = {
-	MX6_PAD_GPIO_16__ENET_REF_CLK	| MUX_PAD_CTRL(0x4001b0a8),
-	MX6_PAD_ENET_MDIO__ENET_MDIO	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_MDC__ENET_MDC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_TX_EN__ENET_TX_EN	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_RX_ER__ENET_RX_ER	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_CRS_DV__ENET_RX_EN	| MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-static void setup_iomux_enet(void)
-{
-	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
-
-	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
-	/* set GPIO_16 as ENET_REF_CLK_OUT */
-	setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
-}
-
 iomux_v3_cfg_t const usdhc1_pads[] = {
 	MX6_PAD_SD1_CLK__SD1_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD1_CMD__SD1_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -176,86 +100,11 @@ iomux_v3_cfg_t const usdhc1_pads[] = {
 	MX6_PAD_SD1_DAT3__SD1_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
 };
 
-iomux_v3_cfg_t const usdhc2_pads[] = {
-	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const ecspi4_pads[] = {
-	MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const display_pads[] = {
-	MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL),
-	MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15,
-	MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02,
-	MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03,
-	MX6_PAD_DI0_PIN4__GPIO4_IO20,
-	MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
-	MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
-	MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
-	MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
-	MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
-	MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
-	MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
-	MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
-	MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
-	MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
-	MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
-	MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
-	MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
-	MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
-	MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
-	MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
-	MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
-	MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
-	MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18,
-	MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19,
-	MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20,
-	MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21,
-	MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22,
-	MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23,
-};
-
-static iomux_v3_cfg_t const backlight_pads[] = {
-	MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_SD4_DAT1__PWM3_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
-	return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
-		? (IMX_GPIO_NR(3, 20)) : -1;
-}
-
-static void setup_spi(void)
-{
-	int i;
-
-	imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
-	for (i = 0; i < 3; i++)
-		enable_spi_clk(true, i);
-
-	/* set cs1 to high */
-	gpio_direction_output(ECSPI4_CS1, 1);
-}
-
-static void setup_iomux_gpio(void)
+int dram_init(void)
 {
-	imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads));
-}
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
 
-static void setup_iomux_uart(void)
-{
-	imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+	return 0;
 }
 
 #ifdef CONFIG_FSL_ESDHC
@@ -272,13 +121,24 @@ int board_mmc_getcd(struct mmc *mmc)
 int board_mmc_init(bd_t *bis)
 {
 	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-
 	imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
-	imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-
-	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]) |
-		fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
+#if (CONFIG_SYS_BOARD_VERSION == 2)
+	/*
+	 * usdhc2 has a levelshifter on the carrier board Rev. DV1,
+	 * that will automatically detect the driving direction.
+	 * During initialisation this isn't working correctly,
+	 * which causes DAT3 to be driven low towards the SD-card.
+	 * This causes a SD-card enetring the SPI-Mode
+	 * and therefore getting inaccessible until next power cycle.
+	 * As workaround we drive the DAT3 line as GPIO and set it high.
+	 * This makes usdhc2 unusable in u-boot, but works for the
+	 * initialisation in Linux
+	 */
+	imx_iomux_v3_setup_pad(MX6_PAD_SD2_DAT3__GPIO1_IO12 |
+			       MUX_PAD_CTRL(NO_PAD_CTRL));
+	gpio_direction_output(IMX_GPIO_NR(1, 12) , 1);
+#endif
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
 }
 #endif
 
@@ -291,48 +151,6 @@ int overwrite_console(void)
 	return 1;
 }
 
-int board_eth_init(bd_t *bis)
-{
-	struct iomuxc *iomuxc_regs =
-				(struct iomuxc *)IOMUXC_BASE_ADDR;
-	int ret;
-
-	setup_iomux_enet();
-	/* clear gpr1[14], gpr1[18:17] to select anatop clock */
-	clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC_MASK, 0);
-
-	ret = enable_fec_anatop_clock(ENET_50MHZ);
-	if (ret)
-		return ret;
-
-	return cpu_eth_init(bis);
-}
-#if defined(CONFIG_VIDEO_IPUV3)
-
-static void enable_lvds(struct display_info_t const *dev)
-{
-	imx_iomux_v3_setup_multiple_pads(
-		display_pads,
-		 ARRAY_SIZE(display_pads));
-	imx_iomux_v3_setup_multiple_pads(
-		backlight_pads,
-		 ARRAY_SIZE(backlight_pads));
-
-	/* enable backlight PWM 3 */
-	if (pwm_init(2, 0, 0))
-		goto error;
-	/* duty cycle 500ns, period: 3000ns */
-	if (pwm_config(2, 500, 3000))
-		goto error;
-	if (pwm_enable(2))
-		goto error;
-	return;
-
-error:
-	puts("error init pwm for backlight\n");
-	return;
-}
-
 struct display_info_t const displays[] = {
 	{
 		.bus	= -1,
@@ -356,43 +174,39 @@ struct display_info_t const displays[] = {
 			.vmode          = FB_VMODE_NONINTERLACED
 		}
 	}
+#if (CONFIG_SYS_BOARD_VERSION == 2)
+	, {
+		.bus	= -1,
+		.addr	= 0,
+		.pixfmt	= IPU_PIX_FMT_RGB24,
+		.detect	= NULL,
+		.enable	= enable_spi_display,
+		.mode	= {
+			.name           = "lg4573",
+			.refresh        = 60,
+			.xres           = 480,
+			.yres           = 800,
+			.pixclock       = 37037,
+			.left_margin    = 59,
+			.right_margin   = 10,
+			.upper_margin   = 15,
+			.lower_margin   = 15,
+			.hsync_len      = 10,
+			.vsync_len      = 15,
+			.sync           = FB_SYNC_EXT | FB_SYNC_HOR_HIGH_ACT |
+					  FB_SYNC_VERT_HIGH_ACT,
+			.vmode          = FB_VMODE_NONINTERLACED
+		}
+	}
+#endif
 };
 size_t display_count = ARRAY_SIZE(displays);
 
-static void setup_display(void)
-{
-	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-	int reg;
-
-	enable_ipu_clock();
-
-	reg = readl(&mxc_ccm->cs2cdr);
-	/* select pll 5 clock */
-	reg &= MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK;
-	reg &= MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK;
-	writel(reg, &mxc_ccm->cs2cdr);
-
-	imx_iomux_v3_setup_multiple_pads(backlight_pads,
-					 ARRAY_SIZE(backlight_pads));
-}
-
 /* no console on this board */
 int board_cfb_skip(void)
 {
 	return 1;
 }
-#endif
-
-int board_early_init_f(void)
-{
-	setup_iomux_uart();
-	setup_iomux_gpio();
-
-#if defined(CONFIG_VIDEO_IPUV3)
-	setup_display();
-#endif
-	return 0;
-}
 
 iomux_v3_cfg_t nfc_pads[] = {
 	MX6_PAD_NANDF_CLE__NAND_CLE		| MUX_PAD_CTRL(NO_PAD_CTRL),
@@ -424,6 +238,9 @@ static void setup_gpmi_nand(void)
 	imx_iomux_v3_setup_multiple_pads(nfc_pads,
 					 ARRAY_SIZE(nfc_pads));
 
+	/* gate ENFC_CLK_ROOT clock first,before clk source switch */
+	clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
 	/* config gpmi and bch clock to 100 MHz */
 	clrsetbits_le32(&mxc_ccm->cs2cdr,
 			MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
@@ -433,6 +250,9 @@ static void setup_gpmi_nand(void)
 			MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
 			MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
 
+	/* enable ENFC_CLK_ROOT clock */
+	setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
 	/* enable gpmi and bch clock gating */
 	setbits_le32(&mxc_ccm->CCGR4,
 		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
@@ -460,43 +280,26 @@ int board_init(void)
 		  &i2c_pad_info2);
 	setup_i2c(2, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
 		  &i2c_pad_info3);
-
-	/* i2c4 not used, set it to gpio input */
-	gpio_request(IMX_GPIO_NR(1, 7), "i2c4_scl");
-	gpio_direction_input(IMX_GPIO_NR(1, 7));
-	gpio_request(IMX_GPIO_NR(1, 8), "i2c4_sda");
-	gpio_direction_input(IMX_GPIO_NR(1, 8));
+	setup_i2c4();
 
 	/* SPI NOR Flash read only */
 	gpio_request(CONFIG_GPIO_ENABLE_SPI_FLASH, "ena_spi_nor");
 	gpio_direction_output(CONFIG_GPIO_ENABLE_SPI_FLASH, 0);
 	gpio_free(CONFIG_GPIO_ENABLE_SPI_FLASH);
 
-	/* enable LED */
-	gpio_request(IMX_GPIO_NR(2, 13), "LED ena");
-	gpio_direction_output(IMX_GPIO_NR(2, 13), 0);
-
-	gpio_request(IMX_GPIO_NR(1, 3), "LED yellow");
-	gpio_direction_output(IMX_GPIO_NR(1, 3), 1);
-	gpio_request(IMX_GPIO_NR(1, 4), "LED red");
-	gpio_direction_output(IMX_GPIO_NR(1, 4), 1);
-	gpio_request(IMX_GPIO_NR(1, 5), "LED green");
-	gpio_direction_output(IMX_GPIO_NR(1, 5), 1);
-	gpio_request(IMX_GPIO_NR(1, 6), "LED blue");
-	gpio_direction_output(IMX_GPIO_NR(1, 6), 1);
-
+	setup_board_gpio();
 	setup_gpmi_nand();
+	setup_board_spi();
 
 	/* GPIO_1 for USB_OTG_ID */
-	setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_USB_OTG_ID_SEL_MASK);
+	clrsetbits_le32(&iomux->gpr[1], IOMUXC_GPR1_USB_OTG_ID_SEL_MASK, 0);
 	imx_iomux_v3_setup_multiple_pads(misc_pads, ARRAY_SIZE(misc_pads));
-
 	return 0;
 }
 
 int checkboard(void)
 {
-	puts("Board: aristaitenos\n");
+	printf("Board: %s\n", CONFIG_BOARDNAME);
 	return 0;
 }
 
diff --git a/board/aristainetos/aristainetos2.cfg b/board/aristainetos/aristainetos2.cfg
new file mode 100644
index 0000000..dc2143b
--- /dev/null
+++ b/board/aristainetos/aristainetos2.cfg
@@ -0,0 +1,34 @@
+/*
+ * (C) Copyright 2015
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd
+ */
+BOOT_FROM      spi
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch/mx6-ddr.h"
+#include "asm/arch/iomux.h"
+#include "asm/arch/crm_regs.h"
+
+#include "ddr-setup2.cfg"
+#include "nt5cc256m16cp.cfg"
+#include "clocks2.cfg"
+#include "axi.cfg"
diff --git a/board/aristainetos/axi.cfg b/board/aristainetos/axi.cfg
new file mode 100644
index 0000000..0bb816c
--- /dev/null
+++ b/board/aristainetos/axi.cfg
@@ -0,0 +1,22 @@
+/*
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *      Addr-type register length (1,2 or 4 bytes)
+ *      Address   absolute address of the register
+ *      value     value to be stored in the register
+ */
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
+
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
+DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
diff --git a/board/aristainetos/clocks2.cfg b/board/aristainetos/clocks2.cfg
new file mode 100644
index 0000000..987d9a4
--- /dev/null
+++ b/board/aristainetos/clocks2.cfg
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *      Addr-type register length (1,2 or 4 bytes)
+ *      Address   absolute address of the register
+ *      value     value to be stored in the register
+ */
+
+/* set the default clock gate to save power */
+DATA 4, CCM_CCGR0, 0x00c03f3f
+DATA 4, CCM_CCGR1, 0x0030fcff
+DATA 4, CCM_CCGR2, 0x0fffcfc0
+DATA 4, CCM_CCGR3, 0x3ff0300f
+DATA 4, CCM_CCGR4, 0xfffff300
+DATA 4, CCM_CCGR5, 0x0f0000c3
+DATA 4, CCM_CCGR6, 0x00000fff
diff --git a/board/aristainetos/ddr-setup2.cfg b/board/aristainetos/ddr-setup2.cfg
new file mode 100644
index 0000000..3d5d894
--- /dev/null
+++ b/board/aristainetos/ddr-setup2.cfg
@@ -0,0 +1,59 @@
+/*
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *      Addr-type register length (1,2 or 4 bytes)
+ *      Address   absolute address of the register
+ *      value     value to be stored in the register
+ */
+
+/* DDR IO TYPE */
+DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000C0000
+DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000
+/* Clock */
+DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000030
+/* Address */
+DATA 4, MX6_IOM_DRAM_CAS, 0x00000030
+DATA 4, MX6_IOM_DRAM_RAS, 0x00000030
+DATA 4, MX6_IOM_GRP_ADDDS, 0x00000030
+/* Control */
+DATA 4, MX6_IOM_DRAM_RESET, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000
+DATA 4, MX6_IOM_DRAM_SDODT0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDODT1, 0x00000030
+DATA 4, MX6_IOM_GRP_CTLDS, 0x00000030
+/* Data Strobe */
+DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000
+DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS4, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS5, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS6, 0x00000028
+DATA 4, MX6_IOM_DRAM_SDQS7, 0x00000028
+DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000
+DATA 4, MX6_IOM_GRP_B0DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B1DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B2DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B3DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B4DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B5DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B6DS, 0x00000028
+DATA 4, MX6_IOM_GRP_B7DS, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM0, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM1, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM2, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM3, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM4, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM5, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM6, 0x00000028
+DATA 4, MX6_IOM_DRAM_DQM7, 0x00000028
diff --git a/board/aristainetos/nt5cc256m16cp.cfg b/board/aristainetos/nt5cc256m16cp.cfg
new file mode 100644
index 0000000..2ff41e9
--- /dev/null
+++ b/board/aristainetos/nt5cc256m16cp.cfg
@@ -0,0 +1,60 @@
+/*
+ * Copyright (C) 2013 Boundary Devices
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+/* ZQ Calibration */
+DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xa1390003
+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
+/*
+ * DQS gating, read delay, write delay calibration values
+ */
+DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x42190217
+DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x017B017B
+DATA 4, MX6_MMDC_P1_MPDGCTRL0, 0x4176017B
+DATA 4, MX6_MMDC_P1_MPDGCTRL1, 0x015F016C
+DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x4C4C4D4C
+DATA 4, MX6_MMDC_P1_MPRDDLCTL, 0x4A4D4C48
+DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x3F3F3F40
+DATA 4, MX6_MMDC_P1_MPWRDLCTL, 0x3538382E
+/* read data bit delay */
+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
+/* Complete calibration by forced measurment */
+DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
+DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800
+/* in DDR3, 64-bit mode, only MMDC0 is initiated */
+DATA 4, MX6_MMDC_P0_MDPDC, 0x00020025
+DATA 4, MX6_MMDC_P0_MDOTC, 0x00333030
+DATA 4, MX6_MMDC_P0_MDCFG0, 0x676B5313
+DATA 4, MX6_MMDC_P0_MDCFG1, 0xB66E8B63
+DATA 4, MX6_MMDC_P0_MDCFG2, 0x01FF00DB
+DATA 4, MX6_MMDC_P0_MDMISC, 0x00001740
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
+DATA 4, MX6_MMDC_P0_MDRWD, 0x000026d2
+DATA 4, MX6_MMDC_P0_MDOR, 0x006B1023
+DATA 4, MX6_MMDC_P0_MDASP, 0x00000027
+DATA 4, MX6_MMDC_P0_MDCTL, 0x84190000
+
+DATA 4, MX6_MMDC_P0_MDSCR, 0x04008032
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00048031
+DATA 4, MX6_MMDC_P0_MDSCR, 0x05208030
+DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
+
+/* final ddr setup */
+DATA 4, MX6_MMDC_P0_MDREF, 0x00005800
+DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00011117
+DATA 4, MX6_MMDC_P1_MPODTCTRL, 0x00011117
+DATA 4, MX6_MMDC_P0_MDPDC, 0x00025565
+DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
diff --git a/configs/aristainetos2_defconfig b/configs/aristainetos2_defconfig
new file mode 100644
index 0000000..e536646
--- /dev/null
+++ b/configs/aristainetos2_defconfig
@@ -0,0 +1,3 @@
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aristainetos/aristainetos2.cfg,MX6DL"
+CONFIG_ARM=y
+CONFIG_TARGET_ARISTAINETOS2=y
diff --git a/include/configs/aristainetos-common.h b/include/configs/aristainetos-common.h
new file mode 100644
index 0000000..7d60cf9
--- /dev/null
+++ b/include/configs/aristainetos-common.h
@@ -0,0 +1,333 @@
+/*
+ * (C) Copyright 2015
+ * (C) Copyright 2014
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6Q SabreSD board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __ARISTAINETOS_COMMON_CONFIG_H
+#define __ARISTAINETOS_COMMON_CONFIG_H
+
+#define CONFIG_MX6
+
+#include "mx6_common.h"
+#include <linux/sizes.h>
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+#define CONFIG_MACH_TYPE	4501
+#define CONFIG_MMCROOT		"/dev/mmcblk0p1"
+#define PHYS_SDRAM_SIZE		(1u * 1024 * 1024 * 1024)
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(64 * SZ_1M)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+
+#define CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR      0
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		0
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_MICREL
+
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_MTD
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_MXC_SPI
+#define CONFIG_SF_DEFAULT_BUS		3
+#define CONFIG_SF_DEFAULT_SPEED		20000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_SETEXPR
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY		3
+
+#define CONFIG_LOADADDR			0x12000000
+#define CONFIG_SYS_TEXT_BASE		0x17800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"script=u-boot.scr\0" \
+	"fit_file=/boot/system.itb\0" \
+	"loadaddr=0x12000000\0" \
+	"fit_addr_r=0x14000000\0" \
+	"uboot=/boot/u-boot.imx\0" \
+	"uboot_sz=d0000\0" \
+	"rescue_sys_addr=f0000\0" \
+	"rescue_sys_length=f10000\0" \
+	"panel=lb07wv8\0" \
+	"splashpos=m,m\0" \
+	"console=" CONFIG_CONSOLE_DEV "\0" \
+	"fdt_high=0xffffffff\0"	  \
+	"initrd_high=0xffffffff\0" \
+	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+	"set_fit_default=fdt addr ${fit_addr_r};fdt set /configurations " \
+		"default ${board_type}\0" \
+	"get_env=mw ${loadaddr} 0 0x20000;" \
+		"mmc rescan;" \
+		"ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} env.txt;" \
+		"env import -t ${loadaddr}\0" \
+	"default_env=mw ${loadaddr} 0 0x20000;" \
+		"env export -t ${loadaddr} serial# ethaddr eth1addr " \
+		"board_type panel;" \
+		"env default -a;" \
+		"env import -t ${loadaddr}\0" \
+	"loadbootscript=" \
+		"ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"mmcpart=1\0" \
+	"mmcdev=0\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} " \
+		"root=${mmcroot}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs addmtd addmisc set_fit_default;" \
+		"bootm ${fit_addr_r}\0" \
+	"mmc_load_fit=ext2load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
+		"${fit_file}\0" \
+	"mmc_load_uboot=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
+		"${uboot}\0" \
+	"mmc_upd_uboot=mw.b ${loadaddr} 0xff ${uboot_sz};" \
+		"setexpr cmp_buf ${loadaddr} + ${uboot_sz};" \
+		"setexpr uboot_maxsize ${uboot_sz} - 400;" \
+		"mw.b ${cmp_buf} 0x00 ${uboot_sz};" \
+		"run mmc_load_uboot;sf probe;sf erase 0 ${uboot_sz};" \
+		"sf write ${loadaddr} 400 ${filesize};" \
+		"sf read ${cmp_buf} 400 ${uboot_sz};" \
+		"cmp.b ${loadaddr} ${cmp_buf} ${uboot_maxsize}\0" \
+	"ubiboot=echo Booting from ubi ...; " \
+		"run ubiargs addmtd addmisc set_fit_default;" \
+		"bootm ${fit_addr_r}\0" \
+	"ubifs_load_fit=sf probe;ubi part ubi 2048;ubifsmount ubi:rootfs;" \
+		"ubifsload ${fit_addr_r} /boot/system.itb; " \
+		"imi ${fit_addr_r}\0 " \
+	"rescueargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/ram rw\0 " \
+	"rescueboot=echo Booting rescue system from NOR ...; " \
+		"run rescueargs addmtd addmisc set_fit_default;" \
+		"bootm ${fit_addr_r}\0" \
+	"rescue_load_fit=sf probe;sf read ${fit_addr_r} ${rescue_sys_addr} " \
+		"${rescue_sys_length}; imi ${fit_addr_r}\0" \
+	CONFIG_EXTRA_ENV_BOARD_SETTINGS
+
+#define CONFIG_BOOTCOMMAND \
+	"mmc dev ${mmcdev};" \
+	"if mmc rescan; then " \
+		"if run loadbootscript; then " \
+			"run bootscript; " \
+		"else " \
+			"if run mmc_load_fit; then " \
+				"run mmcboot; " \
+			"else " \
+				"if run ubifs_load_fit; then " \
+					"run ubiboot; " \
+				"else " \
+					"if run rescue_load_fit; then " \
+						"run rescueboot; " \
+					"else " \
+						"echo RESCUE SYSTEM BOOT " \
+							"FAILURE;" \
+					"fi; " \
+				"fi; " \
+			"fi; " \
+		"fi; " \
+	"else " \
+		"if run ubifs_load_fit; then " \
+			"run ubiboot; " \
+		"else " \
+			"if run rescue_load_fit; then " \
+				"run rescueboot; " \
+			"else " \
+				"echo RESCUE SYSTEM BOOT FAILURE;" \
+			"fi; " \
+		"fi; " \
+	"fi"
+
+#define CONFIG_ARP_TIMEOUT		200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE		256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS             16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x100000)
+#define CONFIG_SYS_MEMTEST_SCRATCH	0x10800000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE		(128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE			(12 * 1024)
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
+#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
+#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SECT_SIZE		(0x010000)
+#define CONFIG_ENV_OFFSET		(0x0d0000)
+#define CONFIG_ENV_OFFSET_REDUND	(0x0e0000)
+
+#define CONFIG_OF_LIBFDT
+
+#define CONFIG_CMD_CACHE
+
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_SYS_I2C_SLAVE		0x7f
+#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x00} }
+
+#define CONFIG_CMD_GPIO
+
+/* NAND stuff */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* RTC */
+#define CONFIG_SYS_I2C_RTC_ADDR	0x68
+#define CONFIG_SYS_RTC_BUS_NUM	2
+#define CONFIG_RTC_M41T11
+#define CONFIG_CMD_DATE
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_FAT
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+
+/* UBI support */
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+
+#define CONFIG_MTD_UBI_FASTMAP
+#define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT	1
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+
+#define CONFIG_FIT
+
+/* Framebuffer */
+#define CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+/* check this console not needed, after test remove it */
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_SPLASH_SCREEN_ALIGN
+#define CONFIG_BMP_16BPP
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_IPUV3_CLK 198000000
+#define CONFIG_IMX_VIDEO_SKIP
+
+#define CONFIG_CMD_BMP
+
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK	66000000
+
+#endif /* __ARISTAINETOS_COMMON_CONFIG_H */
diff --git a/include/configs/aristainetos.h b/include/configs/aristainetos.h
index cc26790..258866a 100644
--- a/include/configs/aristainetos.h
+++ b/include/configs/aristainetos.h
@@ -13,333 +13,31 @@
 #ifndef __ARISTAINETOS_CONFIG_H
 #define __ARISTAINETOS_CONFIG_H
 
-#define CONFIG_MX6
-
-#include "mx6_common.h"
-#include <linux/sizes.h>
-
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
-#include <asm/arch/imx-regs.h>
-#include <asm/imx-common/gpio.h>
-
-#define CONFIG_MACH_TYPE	4501
-#define CONFIG_MMCROOT		"/dev/mmcblk0p1"
+#define CONFIG_SYS_BOARD_VERSION	1
 #define CONFIG_HOSTNAME		aristainetos
-#define PHYS_SDRAM_SIZE		(1u * 1024 * 1024 * 1024)
-
-#define CONFIG_SYS_GENERIC_BOARD
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(64 * SZ_1M)
+#define CONFIG_BOARDNAME	"aristainetos"
 
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_MXC_GPIO
-
-#define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE	UART5_BASE
 #define CONFIG_CONSOLE_DEV	"ttymxc4"
 
-#define CONFIG_CMD_FUSE
-#define CONFIG_MXC_OCOTP
-
-/* MMC Configs */
-#define CONFIG_FSL_ESDHC
-#define CONFIG_FSL_USDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR      0
-
-#define CONFIG_MMC
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_BOUNCE_BUFFER
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_FEC_MXC
-#define CONFIG_MII
-#define IMX_FEC_BASE			ENET_BASE_ADDR
 #define CONFIG_FEC_XCV_TYPE		RMII
-#define CONFIG_ETHPRIME			"FEC"
-#define CONFIG_FEC_MXC_PHYADDR		0
-
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_MICREL
 
-#define CONFIG_CMD_SF
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_MTD
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_MXC_SPI
-#define CONFIG_SF_DEFAULT_BUS		3
 #define CONFIG_SF_DEFAULT_CS		0
-#define CONFIG_SF_DEFAULT_SPEED		20000000
-#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
-#define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX		1
-#define CONFIG_BAUDRATE			115200
 
-/* Command definition */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BMODE
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_SETEXPR
-#undef CONFIG_CMD_IMLS
-
-#define CONFIG_BOOTDELAY		3
-
-#define CONFIG_LOADADDR			0x12000000
-#define CONFIG_SYS_TEXT_BASE		0x17800000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"script=u-boot.scr\0" \
-	"fit_file=/boot/system.itb\0" \
-	"loadaddr=0x12000000\0" \
-	"fit_addr_r=0x14000000\0" \
-	"uboot=/boot/u-boot.imx\0" \
-	"uboot_sz=d0000\0" \
-	"rescue_sys_addr=f0000\0" \
-	"rescue_sys_length=f10000\0" \
+#define CONFIG_EXTRA_ENV_BOARD_SETTINGS \
 	"board_type=aristainetos7 at 1\0" \
-	"panel=lb07wv8\0" \
-	"splashpos=m,m\0" \
-	"console=" CONFIG_CONSOLE_DEV "\0" \
-	"fdt_high=0xffffffff\0"	  \
-	"initrd_high=0xffffffff\0" \
 	"mtdids=nand0=gpmi-nand,nor0=spi3.0\0" \
 	"mtdparts=mtdparts=spi3.0:832k(u-boot),64k(env),64k(env-red)," \
 		"-(rescue-system);gpmi-nand:-(ubi)\0" \
 	"addmisc=setenv bootargs ${bootargs} consoleblank=0\0" \
 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
-	"set_fit_default=fdt addr ${fit_addr_r};fdt set /configurations " \
-		"default ${board_type}\0" \
-	"get_env=mw ${loadaddr} 0 0x20000;" \
-		"mmc rescan;" \
-		"ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} env.txt;" \
-		"env import -t ${loadaddr}\0" \
-	"default_env=mw ${loadaddr} 0 0x20000;" \
-		"env export -t ${loadaddr} serial# ethaddr eth1addr " \
-		"board_type panel;" \
-		"env default -a;" \
-		"env import -t ${loadaddr}\0" \
-	"loadbootscript=" \
-		"ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
-	"bootscript=echo Running bootscript from mmc ...; " \
-		"source\0" \
-	"mmcpart=1\0" \
-	"mmcdev=0\0" \
-	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
-	"mmcargs=setenv bootargs console=${console},${baudrate} " \
-		"root=${mmcroot}\0" \
-	"mmcboot=echo Booting from mmc ...; " \
-		"run mmcargs addmtd addmisc set_fit_default;" \
-		"bootm ${fit_addr_r}\0" \
-	"mmc_load_fit=ext2load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
-		"${fit_file}\0" \
-	"mmc_load_uboot=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
-		"${uboot}\0" \
-	"mmc_upd_uboot=mw.b ${loadaddr} 0xff ${uboot_sz};" \
-		"setexpr cmp_buf ${loadaddr} + ${uboot_sz};" \
-		"setexpr uboot_maxsize ${uboot_sz} - 400;" \
-		"mw.b ${cmp_buf} 0x00 ${uboot_sz};" \
-		"run mmc_load_uboot;sf probe;sf erase 0 ${uboot_sz};" \
-		"sf write ${loadaddr} 400 ${filesize};" \
-		"sf read ${cmp_buf} 400 ${uboot_sz};" \
-		"cmp.b ${loadaddr} ${cmp_buf} ${uboot_maxsize}\0" \
 	"ubiargs=setenv bootargs console=${console},${baudrate} " \
-		"ubi.mtd=0,2048 root=ubi0:rootfs rootfstype=ubifs\0 " \
-	"ubiboot=echo Booting from ubi ...; " \
-		"run ubiargs addmtd addmisc set_fit_default;" \
-		"bootm ${fit_addr_r}\0" \
-	"ubifs_load_fit=sf probe;ubi part ubi 2048;ubifsmount ubi:rootfs;" \
-		"ubifsload ${fit_addr_r} /boot/system.itb; " \
-		"imi ${fit_addr_r}\0 " \
-	"rescueargs=setenv bootargs console=${console},${baudrate} " \
-		"root=/dev/ram rw\0 " \
-	"rescueboot=echo Booting rescue system from NOR ...; " \
-		"run rescueargs addmtd addmisc set_fit_default;" \
-		"bootm ${fit_addr_r}\0" \
-	"rescue_load_fit=sf probe;sf read ${fit_addr_r} ${rescue_sys_addr} " \
-		"${rescue_sys_length}; imi ${fit_addr_r}\0 "
-
-#define CONFIG_BOOTCOMMAND \
-	"mmc dev ${mmcdev};" \
-	"if mmc rescan; then " \
-		"if run loadbootscript; then " \
-			"run bootscript; " \
-		"else " \
-			"if run mmc_load_fit; then " \
-				"run mmcboot; " \
-			"else " \
-				"if run ubifs_load_fit; then " \
-					"run ubiboot; " \
-				"else " \
-					"if run rescue_load_fit; then " \
-						"run rescueboot; " \
-					"else " \
-						"echo RESCUE SYSTEM BOOT " \
-							"FAILURE;" \
-					"fi; " \
-				"fi; " \
-			"fi; " \
-		"fi; " \
-	"else " \
-		"if run ubifs_load_fit; then " \
-			"run ubiboot; " \
-		"else " \
-			"if run rescue_load_fit; then " \
-				"run rescueboot; " \
-			"else " \
-				"echo RESCUE SYSTEM BOOT FAILURE;" \
-			"fi; " \
-		"fi; " \
-	"fi"
-
-#define CONFIG_ARP_TIMEOUT		200UL
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_CBSIZE		256
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS             16
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x100000)
-#define CONFIG_SYS_MEMTEST_SCRATCH	0x10800000
-
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
-
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE		(128 * 1024)
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
-	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
-	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FLASH and environment organization */
-#define CONFIG_SYS_NO_FLASH
-
-#define CONFIG_ENV_SIZE			(12 * 1024)
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
-#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
-#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
-#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
-#define CONFIG_ENV_SECT_SIZE		(0x010000)
-#define CONFIG_ENV_OFFSET		(0x0d0000)
-#define CONFIG_ENV_OFFSET_REDUND	(0x0e0000)
-
-#define CONFIG_OF_LIBFDT
-
-#define CONFIG_CMD_CACHE
-
-#define CONFIG_SYS_FSL_USDHC_NUM	2
-
-#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0x7f
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x00} }
-
-#define CONFIG_CMD_GPIO
-#define CONFIG_GPIO_ENABLE_SPI_FLASH	IMX_GPIO_NR(2, 15)
-
-/* NAND stuff */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
-#define CONFIG_NAND_MXS
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BASE		0x40000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* DMA stuff, needed for GPMI/MXS NAND support */
-#define CONFIG_APBH_DMA
-#define CONFIG_APBH_DMA_BURST
-#define CONFIG_APBH_DMA_BURST8
-
-/* RTC */
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68
-#define CONFIG_SYS_RTC_BUS_NUM	2
-#define CONFIG_RTC_M41T11
-#define CONFIG_CMD_DATE
-
-/* USB Configs */
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_FAT
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
-#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS	0
+		"ubi.mtd=0,2048 root=ubi0:rootfs rootfstype=ubifs\0 "
 
 #define ARISTAINETOS_USB_OTG_PWR	IMX_GPIO_NR(4, 15)
 #define ARISTAINETOS_USB_H1_PWR		IMX_GPIO_NR(3, 31)
+#define CONFIG_GPIO_ENABLE_SPI_FLASH	IMX_GPIO_NR(2, 15)
 
-/* UBI support */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_MTD_DEVICE
-#define CONFIG_RBTREE
-#define CONFIG_LZO
-#define CONFIG_CMD_UBI
-#define CONFIG_CMD_UBIFS
-
-#define CONFIG_MTD_UBI_FASTMAP
-#define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT	1
-
-#define CONFIG_HW_WATCHDOG
-#define CONFIG_IMX_WATCHDOG
-
-#define CONFIG_FIT
-
-/* Framebuffer */
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_IPUV3
-/* check this console not needed, after test remove it */
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_BMP_16BPP
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_IPUV3_CLK 198000000
-#define CONFIG_IMX_VIDEO_SKIP
-
-#define CONFIG_CMD_BMP
+#include "aristainetos-common.h"
 
-#define CONFIG_PWM_IMX
-#define CONFIG_IMX6_PWM_PER_CLK	66000000
 #endif                         /* __ARISTAINETOS_CONFIG_H */
diff --git a/include/configs/aristainetos2.h b/include/configs/aristainetos2.h
new file mode 100644
index 0000000..faeafe2d
--- /dev/null
+++ b/include/configs/aristainetos2.h
@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2015
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6DL aristainetos2 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __ARISTAINETOS2_CONFIG_H
+#define __ARISTAINETOS2_CONFIG_H
+
+#define CONFIG_SYS_BOARD_VERSION	2
+#define CONFIG_HOSTNAME		aristainetos2
+#define CONFIG_BOARDNAME	"aristainetos2"
+
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_UART_BASE	UART2_BASE
+#define CONFIG_CONSOLE_DEV	"ttymxc1"
+
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_PHY_MICREL_KSZ9031
+
+#define CONFIG_SF_DEFAULT_CS		1
+
+#define CONFIG_EXTRA_ENV_BOARD_SETTINGS \
+	"board_type=aristainetos2_7 at 1\0" \
+	"nor_bootdelay=-2\0" \
+	"mtdids=nand0=gpmi-nand,nor0=spi3.1\0" \
+	"mtdparts=mtdparts=spi3.1:832k(u-boot),64k(env),64k(env-red)," \
+		"-(rescue-system);gpmi-nand:-(ubi)\0" \
+	"addmisc=setenv bootargs ${bootargs} net.ifnames=0 consoleblank=0\0" \
+	"ubiargs=setenv bootargs console=${console},${baudrate} " \
+		"ubi.mtd=0,4096 root=ubi0:rootfs rootfstype=ubifs\0 "
+
+#define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */
+
+#define ARISTAINETOS_USB_OTG_PWR	IMX_GPIO_NR(4, 15)
+#define ARISTAINETOS_USB_H1_PWR	IMX_GPIO_NR(1, 0)
+#define CONFIG_GPIO_ENABLE_SPI_FLASH	IMX_GPIO_NR(2, 15)
+
+/* Framebuffer */
+#define CONFIG_SYS_LDB_CLOCK 33246000
+#define CONFIG_LG4573
+
+#define CONFIG_CMD_BMP
+
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK	66000000
+
+#include "aristainetos-common.h"
+
+#endif                         /* __ARISTAINETOS2_CONFIG_H */
-- 
2.1.0

^ permalink raw reply related	[flat|nested] 2+ messages in thread
end of thread, other threads:[~2015-05-26 12:20 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-05-18 11:32 [U-Boot] [PATCH v3] arm, imx6: add support for aristainetos2 board Heiko Schocher
2015-05-26 12:20 ` Stefano Babic

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox