From mboxrd@z Thu Jan  1 00:00:00 1970
From: Stefano Babic <sbabic@denx.de>
Date: Mon, 08 Jun 2015 08:50:33 +0200
Subject: [U-Boot] [PATCH 2/2] ot1200: setup i2c bus 1 in
	setup_iomux_i2c()
In-Reply-To: <1433324003-6884-2-git-send-email-christian.gmeiner@gmail.com>
References: <1433324003-6884-1-git-send-email-christian.gmeiner@gmail.com>
 <1433324003-6884-2-git-send-email-christian.gmeiner@gmail.com>
Message-ID: <55753B39.6000706@denx.de>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

On 03/06/2015 11:33, Christian Gmeiner wrote:
> On this bus there is a EEPROM containing EDID and ddr3
> calibration information.
> 
> Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
> ---
>  board/bachmann/ot1200/ot1200.c | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/board/bachmann/ot1200/ot1200.c b/board/bachmann/ot1200/ot1200.c
> index a33d496..2237b7a 100644
> --- a/board/bachmann/ot1200/ot1200.c
> +++ b/board/bachmann/ot1200/ot1200.c
> @@ -122,6 +122,20 @@ static void setup_iomux_features(void)
>  
>  #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
>  
> +/* I2C2 - EEPROM */
> +static struct i2c_pads_info i2c_pad_info1 = {
> +	.scl = {
> +		.i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
> +		.gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
> +		.gp = IMX_GPIO_NR(2, 30)
> +	},
> +	.sda = {
> +		.i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC,
> +		.gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC,
> +		.gp = IMX_GPIO_NR(3, 16)
> +	}
> +};
> +
>  /* I2C3 - IO expander  */
>  static struct i2c_pads_info i2c_pad_info2 = {
>  	.scl = {
> @@ -138,6 +152,7 @@ static struct i2c_pads_info i2c_pad_info2 = {
>  
>  static void setup_iomux_i2c(void)
>  {
> +	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
>  	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
>  }
>  
> 
Applied to u-boot-imx, thanks !

Best regards,
Stefano Babic

-- 
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================