public inbox for u-boot@lists.denx.de
 help / color / mirror / Atom feed
From: Roy Spliet <r.spliet@ultimaker.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [RFC 02/11] mtd/nand: add ONFI timing mode to nand_timings converter
Date: Mon, 08 Jun 2015 10:11:17 +0200	[thread overview]
Message-ID: <55754E25.6020406@ultimaker.com> (raw)
In-Reply-To: <1433541745.2477.31.camel@freescale.com>

Hello Scott et al.,

Op 06-06-15 om 00:02 schreef Scott Wood:
> On Fri, 2015-06-05 at 13:52 +0200, Roy Spliet wrote:
>> From: yassin <yassinjaffer@gmail.com>
>>
>> Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
>> ---
>>   drivers/mtd/nand/Makefile       |   2 +-
>>   drivers/mtd/nand/nand_timings.c | 252
>> ++++++++++++++++++++++++++++++++++++++++
>>   include/linux/mtd/nand.h        |   3 +
>>   3 files changed, 256 insertions(+), 1 deletion(-)
>>   create mode 100644 drivers/mtd/nand/nand_timings.c
> This code comes from Linux and yet I see no acknowledgement of that,
> much less a statement of which version of Linux this was pulled from.
Correct, my apologies as I should have clarified that "work by Boris 
Brezillon" does not
mean "upsteam work". The code comes from Boris' github tree[1] and 
contains work
that was not yet brought upstream, yet is required for NAND on sunxi to 
work.
> It would probably be better to handle this as part of a general sync
> with the Linux mtd code.
Ideally yes, but. In upstream Linux MTD we have a few issues to address 
as shown
by Boris' patch-set, most importantly:
- NAND chip timings (patch 1 to 3)
- Randomisation support (patch 6)
- Per-partition settings for ECC and randomisation (left out of my RFC, 
highly desirable
but not strictly required for U-boot booting)
- OF definition of all the above

U-Boot has the additional challenge
- Partitioning is not done the upstream way, but rather in/around 
cmd_mtdparts

We started discussion on these topics in the #mtd IRC channel (OFTC), 
and several ideas
have come up. The way I see it these issues can currently either be 
addressed by
bolting/duct-taping/tie-wrapping more layers of indirection on top of 
upstream MTD
framework, but really I feel that it might require a bit more of a 
structural approach
that may or may not break existing drivers.
The code I posted as RFC is functional. If you wish to steer towards an 
MTD sync-up, I
highly suggest first getting these issues tackled, and then making sure 
that we extend
the U-boot side of MTD with OF support for everything. This trajectory 
should include
deprecating the current implementation of cmd_mtdparts and hook that 
command up
to the "new" upstream way. In other words: now is probably not the right 
moment.

I'm afraid that as much as I'd like to, I will not have time to address 
every single one
of these issues (not to mention I am hardly the expert in MTD/NAND). I'm 
happy to
think along with designing a sustainable solution, but I will need 
someone to chime
in when it comes to carrying solutions upstream.

Roy

> -Scott

[1] https://github.com/bbrezillon/linux-sunxi/commits/sunxi-nand

-- 


IMAGINE IT >> MAKE IT

Meet us online at Twitter <http://twitter.com/ultimaker>, Facebook 
<http://facebook.com/ultimaker>, Google+ <http://google.com/+Ultimaker>

www.ultimaker.com

  reply	other threads:[~2015-06-08  8:11 UTC|newest]

Thread overview: 49+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-06-05 11:52 [U-Boot] [RFC] Sunxi NAND support for U-Boot Roy Spliet
2015-06-05 11:52 ` [U-Boot] [RFC 01/11] mtd/nand: define struct nand_timings Roy Spliet
2015-06-05 11:52 ` [U-Boot] [RFC 02/11] mtd/nand: add ONFI timing mode to nand_timings converter Roy Spliet
2015-06-05 22:02   ` Scott Wood
2015-06-08  8:11     ` Roy Spliet [this message]
2015-06-08  8:34       ` [U-Boot] [linux-sunxi] " Michal Suchanek
2015-06-08  8:41         ` Roy Spliet
2015-06-14 11:59           ` Boris Brezillon
2015-06-08 20:24       ` [U-Boot] " Scott Wood
2015-06-10  8:33     ` Hans de Goede
2015-06-10 19:06       ` Scott Wood
2015-06-05 11:52 ` [U-Boot] [RFC 03/11] mtd/nand: support ONFI timing mode retrieval for non-ONFI Roy Spliet
2015-06-14 11:53   ` Boris Brezillon
2015-06-05 11:52 ` [U-Boot] [RFC 04/11] mtd/nand: add page status table (pst) Roy Spliet
2015-06-14 11:52   ` Boris Brezillon
2015-06-05 11:52 ` [U-Boot] [RFC 05/11] mtd/nand: take nand_ecc_ctrl initialization out of nand_scan_tail Roy Spliet
2015-06-14 11:50   ` Boris Brezillon
2015-06-05 11:52 ` [U-Boot] [RFC 06/11] mtd/nand: Add randomisation layer Roy Spliet
2015-06-14 11:47   ` Boris Brezillon
2015-06-05 11:52 ` [U-Boot] [RFC 07/11] mtd/nand Add Sunxi NAND driver Roy Spliet
2015-06-14 11:42   ` Boris Brezillon
2015-06-14 11:45     ` Boris Brezillon
2015-06-05 11:52 ` [U-Boot] [RFC 08/11] mtd/nand: Add DT definitions for Olimex Lime Roy Spliet
2015-06-14 11:39   ` Boris Brezillon
2015-06-05 11:52 ` [U-Boot] [RFC 09/11] sunxi/nand: Enable UBI and NAND commands Roy Spliet
2015-06-06 15:13   ` Hans de Goede
2015-06-06 15:36     ` Ian Campbell
2015-06-08  7:38       ` Roy Spliet
2015-06-08  9:12         ` Ian Campbell
2015-06-05 11:52 ` [U-Boot] [RFC 10/11] mtd/nand: Define bootcmd for nand Roy Spliet
2015-06-05 11:52 ` [U-Boot] [RFC 11/11] mtd/nand: Sunxi NAND boot partition definitions Roy Spliet
2015-06-07 16:48   ` [U-Boot] [linux-sunxi] " Michal Suchanek
2015-06-08  8:38     ` Roy Spliet
2015-06-08  8:54       ` Michal Suchanek
2015-06-08  9:11         ` Roy Spliet
2015-06-08 10:48           ` Yassin
2015-06-08 11:35             ` Roy Spliet
2015-06-14 11:31               ` Boris Brezillon
2015-06-15  8:00                 ` Hans de Goede
2015-06-08 13:16       ` Hans de Goede
2015-06-08 13:56         ` Roy Spliet
2015-06-14 11:25     ` Boris Brezillon
2015-06-14 11:56       ` Michal Suchanek
2015-06-14 12:18         ` Boris Brezillon
2015-06-14 17:42           ` Michal Suchanek
2015-06-14 19:07             ` Boris Brezillon
2015-06-06 15:09 ` [U-Boot] [RFC] Sunxi NAND support for U-Boot Hans de Goede
2015-06-06 15:11 ` Hans de Goede
2015-06-14 11:13 ` Boris Brezillon

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=55754E25.6020406@ultimaker.com \
    --to=r.spliet@ultimaker.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox