[U-Boot] [PATCH 2/4] arm: at91: at91sam9m10g45ek/corvus remove useless chip select 1 init

["Andreas Bießmann" <andreas.devel@googlemail.com>]

Hi Erik,

On 08/13/2015 03:43 PM, Erik van Luijk wrote:
> On these boards the DDR is connected to a dedicated controller and not
> to chip select 1 of the EBI.

from the specs this seems correct. Could I please get a Tested-by, since
I do not own one of these boards.

Best regards

Andreas

> 
> Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
> ---
>  board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 8 --------
>  board/siemens/corvus/board.c                    | 8 --------
>  2 files changed, 16 deletions(-)
> 
> diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> index 3e65d71..d2ade4d 100644
> --- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> +++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
> @@ -131,21 +131,13 @@ static void ddr2_conf(struct atmel_mpddr *ddr2)
>  void mem_init(void)
>  {
>  	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
> -	struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
>  	struct atmel_mpddr ddr2;
> -	unsigned long csa;
>  
>  	ddr2_conf(&ddr2);
>  
>  	/* enable DDR2 clock */
>  	writel(0x4, &pmc->scer);
>  
> -	/* Chip select 1 is for DDR2/SDRAM */
> -	csa = readl(&mat->ebicsa);
> -	csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
> -	csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
> -	writel(csa, &mat->ebicsa);
> -
>  	/* DDRAM2 Controller initialize */
>  	ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2);
>  }
> diff --git a/board/siemens/corvus/board.c b/board/siemens/corvus/board.c
> index 9001fcbcf..d74743f 100644
> --- a/board/siemens/corvus/board.c
> +++ b/board/siemens/corvus/board.c
> @@ -144,21 +144,13 @@ static void ddr2_conf(struct atmel_mpddr *ddr2)
>  void mem_init(void)
>  {
>  	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
> -	struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
>  	struct atmel_mpddr ddr2;
> -	unsigned long csa;
>  
>  	ddr2_conf(&ddr2);
>  
>  	/* enable DDR2 clock */
>  	writel(0x4, &pmc->scer);
>  
> -	/* Chip select 1 is for DDR2/SDRAM */
> -	csa = readl(&mat->ebicsa);
> -	csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
> -	csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
> -	writel(csa, &mat->ebicsa);
> -
>  	/* DDRAM2 Controller initialize */
>  	ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2);
>  }
>