From mboxrd@z Thu Jan 1 00:00:00 1970 From: Thomas Chou Date: Tue, 13 Oct 2015 21:13:42 +0800 Subject: [U-Boot] [PATCH] nios2: clean up comments style in start.S In-Reply-To: <1444116616-4473-1-git-send-email-thomas@wytron.com.tw> References: <1444116616-4473-1-git-send-email-thomas@wytron.com.tw> Message-ID: <561D0386.5090309@wytron.com.tw> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de On 10/06/2015 03:30 PM, Thomas Chou wrote: > Clean up comments style in start.S. > > Signed-off-by: Thomas Chou > --- > arch/nios2/cpu/start.S | 21 +++++++++++++-------- > 1 file changed, 13 insertions(+), 8 deletions(-) > Applied to u-boot-nios. > diff --git a/arch/nios2/cpu/start.S b/arch/nios2/cpu/start.S > index 90e0310..00cec40 100644 > --- a/arch/nios2/cpu/start.S > +++ b/arch/nios2/cpu/start.S > @@ -18,7 +18,8 @@ > > _start: > wrctl status, r0 /* Disable interrupts */ > - /* ICACHE INIT -- only the icache line at the reset address > + /* > + * ICACHE INIT -- only the icache line at the reset address > * is invalidated at reset. So the init must stay within > * the cache line size (8 words). If GERMS is used, we'll > * just be invalidating the cache a second time. If cache > @@ -32,7 +33,8 @@ _start: > bgt r5, r0, 0b > br _except_end /* Skip the tramp */ > > - /* EXCEPTION TRAMPOLINE -- the following gets copied > + /* > + * EXCEPTION TRAMPOLINE -- the following gets copied > * to the exception address (below), but is otherwise at the > * default exception vector offset (0x0020). > */ > @@ -42,12 +44,14 @@ _except_start: > jmp et > _except_end: > > - /* INTERRUPTS -- for now, all interrupts masked and globally > + /* > + * INTERRUPTS -- for now, all interrupts masked and globally > * disabled. > */ > wrctl ienable, r0 /* All disabled */ > > - /* DCACHE INIT -- if dcache not implemented, initd behaves as > + /* > + * DCACHE INIT -- if dcache not implemented, initd behaves as > * nop. > */ > movhi r4, %hi(CONFIG_SYS_DCACHELINE_SIZE) > @@ -59,7 +63,8 @@ _except_end: > add r6, r6, r4 > bltu r6, r5, 1b > > - /* RELOCATE CODE, DATA & COMMAND TABLE -- the following code > + /* > + * RELOCATE CODE, DATA & COMMAND TABLE -- the following code > * assumes code, data and the command table are all > * contiguous. This lets us relocate everything as a single > * block. Make sure the linker script matches this ;-) > @@ -89,8 +94,7 @@ _cur: movhi r5, %hi(_cur - _start) > jmp r4 > _reloc: > > - /* STACK INIT -- zero top two words for call back chain. > - */ > + /* STACK INIT -- zero top two words for call back chain. */ > movhi sp, %hi(CONFIG_SYS_INIT_SP) > ori sp, sp, %lo(CONFIG_SYS_INIT_SP) > addi sp, sp, -8 > @@ -116,7 +120,8 @@ _reloc: > ori r2, r2, %lo(board_init_f at h) > callr r2 > > - /* NEVER RETURNS -- but branch to the _start just > + /* > + * NEVER RETURNS -- but branch to the _start just > * in case ;-) > */ > br _start >