* [U-Boot] [PATCH 1/1] arm: at91: reworked meesc board support
@ 2015-10-29 12:38 Daniel Gorsulowski
2015-10-30 4:44 ` [U-Boot] [PATCH V2 " Daniel Gorsulowski
0 siblings, 1 reply; 3+ messages in thread
From: Daniel Gorsulowski @ 2015-10-29 12:38 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
---
board/esd/meesc/meesc.c | 20 ++++++++++++++++----
include/configs/meesc.h | 45 +++++++++++++++++++++++----------------------
2 files changed, 39 insertions(+), 26 deletions(-)
diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
index c5994e0..b7f9f90 100644
--- a/board/esd/meesc/meesc.c
+++ b/board/esd/meesc/meesc.c
@@ -3,7 +3,7 @@
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
- * (C) Copyright 2009-2011
+ * (C) Copyright 2009-2015
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
@@ -28,6 +28,7 @@ DECLARE_GLOBAL_DATA_PTR;
* Miscelaneous platform dependent initialisations
*/
+#ifdef CONFIG_REVISION_TAG
static int hw_rev = -1; /* hardware revision */
int get_hw_rev(void)
@@ -45,6 +46,7 @@ int get_hw_rev(void)
return hw_rev;
}
+#endif /* CONFIG_REVISION_TAG */
#ifdef CONFIG_CMD_NAND
static void meesc_nand_hw_init(void)
@@ -125,12 +127,18 @@ static void meesc_ethercat_hw_init(void)
int dram_init(void)
{
- gd->ram_size = get_ram_size(
- (void *)CONFIG_SYS_SDRAM_BASE,
- CONFIG_SYS_SDRAM_SIZE);
+ /* dram_init must store complete ramsize in gd->ram_size */
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
+ PHYS_SDRAM_SIZE);
return 0;
}
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+}
+
int board_eth_init(bd_t *bis)
{
int rc = 0;
@@ -140,6 +148,7 @@ int board_eth_init(bd_t *bis)
return rc;
}
+#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard(void)
{
char str[32];
@@ -173,10 +182,13 @@ int checkboard(void)
puts(", serial# ");
puts(str);
}
+#ifdef CONFIG_REVISION_TAG
printf("\nHardware-revision: 1.%d\n", get_hw_rev());
+#endif
printf("Mach-type: %lu\n", gd->bd->bi_arch_number);
return 0;
}
+#endif /* CONFIG_DISPLAY_BOARDINFO */
#ifdef CONFIG_SERIAL_TAG
void get_board_serial(struct tag_serialnr *serialnr)
diff --git a/include/configs/meesc.h b/include/configs/meesc.h
index 9c53fb4..d976c8e 100644
--- a/include/configs/meesc.h
+++ b/include/configs/meesc.h
@@ -3,7 +3,7 @@
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
- * (C) Copyright 2009-2011
+ * (C) Copyright 2009-2015
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
@@ -27,7 +27,7 @@
* Since the linker has to swallow that define, we must use a pure
* hex number here!
*/
-#define CONFIG_SYS_TEXT_BASE 0x20002000
+#define CONFIG_SYS_TEXT_BASE 0x21F00000
/*
* since a number of boards are not being listed in linux
@@ -56,14 +56,15 @@
#define CONFIG_DISPLAY_CPUINFO /* display cpu info and speed */
#define CONFIG_PREBOOT /* enable preboot variable */
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_OF_LIBFDT
+
+#define CONFIG_SYS_GENERIC_BOARD
/*
* Hardware drivers
*/
-/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is
reworked */
-#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
-
/* general purpose I/O */
#define CONFIG_AT91_GPIO
@@ -87,10 +88,18 @@
/*
* Command line configuration.
*/
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMLS
+
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
+
+#ifdef CONFIG_SYS_USE_NANDFLASH
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_USB
+#endif
/* LED */
#define CONFIG_AT91_LED
@@ -99,9 +108,12 @@
* SDRAM: 1 bank, min 32, max 128 MB
* Initialized before u-boot gets started.
*/
+#define PHYS_SDRAM ATMEL_BASE_CS1 /* 0x20000000 */
+#define PHYS_SDRAM_SIZE 0x02000000 /* 32 MByte */
+
#define CONFIG_NR_DRAM_BANKS 1
-#define CONFIG_SYS_SDRAM_BASE 0x20000000 /* ATMEL_BASE_CS1 */
-#define CONFIG_SYS_SDRAM_SIZE 0x02000000
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_SDRAM_SIZE PHYS_SDRAM_SIZE
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x00100000)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01E00000)
@@ -133,7 +145,7 @@
#ifdef CONFIG_CMD_NAND
# define CONFIG_NAND_ATMEL
# define CONFIG_SYS_MAX_NAND_DEVICE 1
-# define CONFIG_SYS_NAND_BASE 0x40000000 /* ATMEL_BASE_CS3 */
+# define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 /* 0x40000000 */
# define CONFIG_SYS_NAND_DBW_8
# define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
# define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
@@ -148,19 +160,6 @@
#define CONFIG_NET_RETRY_COUNT 20
#undef CONFIG_RESET_PHY_R
-/* USB */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-
-/* CAN */
-#define CONFIG_AT91_CAN
-
/* hw-controller addresses */
#define CONFIG_ET1100_BASE 0x70000000
@@ -190,6 +189,8 @@
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
/*
* Size of malloc() pool
--
2.5.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [U-Boot] [PATCH V2 1/1] arm: at91: reworked meesc board support
2015-10-29 12:38 [U-Boot] [PATCH 1/1] arm: at91: reworked meesc board support Daniel Gorsulowski
@ 2015-10-30 4:44 ` Daniel Gorsulowski
2015-10-31 20:47 ` Andreas Bießmann
0 siblings, 1 reply; 3+ messages in thread
From: Daniel Gorsulowski @ 2015-10-30 4:44 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
---
Changes in V2:
- Fetched again and created patch against current master
board/esd/meesc/meesc.c | 20 ++++++++++++++++----
include/configs/meesc.h | 42 ++++++++++++++++++++----------------------
2 files changed, 36 insertions(+), 26 deletions(-)
diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
index c5994e0..b7f9f90 100644
--- a/board/esd/meesc/meesc.c
+++ b/board/esd/meesc/meesc.c
@@ -3,7 +3,7 @@
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
- * (C) Copyright 2009-2011
+ * (C) Copyright 2009-2015
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
@@ -28,6 +28,7 @@ DECLARE_GLOBAL_DATA_PTR;
* Miscelaneous platform dependent initialisations
*/
+#ifdef CONFIG_REVISION_TAG
static int hw_rev = -1; /* hardware revision */
int get_hw_rev(void)
@@ -45,6 +46,7 @@ int get_hw_rev(void)
return hw_rev;
}
+#endif /* CONFIG_REVISION_TAG */
#ifdef CONFIG_CMD_NAND
static void meesc_nand_hw_init(void)
@@ -125,12 +127,18 @@ static void meesc_ethercat_hw_init(void)
int dram_init(void)
{
- gd->ram_size = get_ram_size(
- (void *)CONFIG_SYS_SDRAM_BASE,
- CONFIG_SYS_SDRAM_SIZE);
+ /* dram_init must store complete ramsize in gd->ram_size */
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
+ PHYS_SDRAM_SIZE);
return 0;
}
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM;
+ gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+}
+
int board_eth_init(bd_t *bis)
{
int rc = 0;
@@ -140,6 +148,7 @@ int board_eth_init(bd_t *bis)
return rc;
}
+#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard(void)
{
char str[32];
@@ -173,10 +182,13 @@ int checkboard(void)
puts(", serial# ");
puts(str);
}
+#ifdef CONFIG_REVISION_TAG
printf("\nHardware-revision: 1.%d\n", get_hw_rev());
+#endif
printf("Mach-type: %lu\n", gd->bd->bi_arch_number);
return 0;
}
+#endif /* CONFIG_DISPLAY_BOARDINFO */
#ifdef CONFIG_SERIAL_TAG
void get_board_serial(struct tag_serialnr *serialnr)
diff --git a/include/configs/meesc.h b/include/configs/meesc.h
index 9c53fb4..10a6ce9 100644
--- a/include/configs/meesc.h
+++ b/include/configs/meesc.h
@@ -3,7 +3,7 @@
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
- * (C) Copyright 2009-2011
+ * (C) Copyright 2009-2015
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
@@ -27,7 +27,7 @@
* Since the linker has to swallow that define, we must use a pure
* hex number here!
*/
-#define CONFIG_SYS_TEXT_BASE 0x20002000
+#define CONFIG_SYS_TEXT_BASE 0x21F00000
/*
* since a number of boards are not being listed in linux
@@ -56,14 +56,13 @@
#define CONFIG_DISPLAY_CPUINFO /* display cpu info and speed */
#define CONFIG_PREBOOT /* enable preboot variable */
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_OF_LIBFDT
/*
* Hardware drivers
*/
-/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is
reworked */
-#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
-
/* general purpose I/O */
#define CONFIG_AT91_GPIO
@@ -87,10 +86,17 @@
/*
* Command line configuration.
*/
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_IMLS
+
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
+
+#ifdef CONFIG_SYS_USE_NANDFLASH
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_USB
+#endif
/* LED */
#define CONFIG_AT91_LED
@@ -99,9 +105,12 @@
* SDRAM: 1 bank, min 32, max 128 MB
* Initialized before u-boot gets started.
*/
+#define PHYS_SDRAM ATMEL_BASE_CS1 /* 0x20000000 */
+#define PHYS_SDRAM_SIZE 0x02000000 /* 32 MByte */
+
#define CONFIG_NR_DRAM_BANKS 1
-#define CONFIG_SYS_SDRAM_BASE 0x20000000 /* ATMEL_BASE_CS1 */
-#define CONFIG_SYS_SDRAM_SIZE 0x02000000
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_SDRAM_SIZE PHYS_SDRAM_SIZE
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x00100000)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01E00000)
@@ -133,7 +142,7 @@
#ifdef CONFIG_CMD_NAND
# define CONFIG_NAND_ATMEL
# define CONFIG_SYS_MAX_NAND_DEVICE 1
-# define CONFIG_SYS_NAND_BASE 0x40000000 /* ATMEL_BASE_CS3 */
+# define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 /* 0x40000000 */
# define CONFIG_SYS_NAND_DBW_8
# define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
# define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
@@ -148,19 +157,6 @@
#define CONFIG_NET_RETRY_COUNT 20
#undef CONFIG_RESET_PHY_R
-/* USB */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
-#define CONFIG_USB_OHCI_NEW
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SYS_USB_OHCI_CPU_INIT
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-
-/* CAN */
-#define CONFIG_AT91_CAN
-
/* hw-controller addresses */
#define CONFIG_ET1100_BASE 0x70000000
@@ -190,6 +186,8 @@
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_HUSH_PARSER
/*
* Size of malloc() pool
--
2.5.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [U-Boot] [PATCH V2 1/1] arm: at91: reworked meesc board support
2015-10-30 4:44 ` [U-Boot] [PATCH V2 " Daniel Gorsulowski
@ 2015-10-31 20:47 ` Andreas Bießmann
0 siblings, 0 replies; 3+ messages in thread
From: Andreas Bießmann @ 2015-10-31 20:47 UTC (permalink / raw)
To: u-boot
Hi Daniel,
On 30.10.15 05:44, Daniel Gorsulowski wrote:
> Signed-off-by: Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
> ---
> Changes in V2:
> - Fetched again and created patch against current master
could you please regenerate another one:
---8<---
Applying: arm: at91: reworked meesc board support
fatal: corrupt patch at line 116
Patch failed at 0001 arm: at91: reworked meesc board support
The copy of the patch that failed is found in:
/Users/andreas/src/u-boot/.git/rebase-apply/patch
When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead.
To restore the original branch and stop patching, run "git am --abort".
andreas at imac % patch -p1 < .git/rebase-apply/patch
patching file board/esd/meesc/meesc.c
Hunk #1 FAILED at 3.
Hunk #2 FAILED at 28.
Hunk #3 FAILED at 46.
Hunk #4 FAILED at 127.
Hunk #5 FAILED at 148.
Hunk #6 FAILED at 182.
6 out of 6 hunks FAILED -- saving rejects to file
board/esd/meesc/meesc.c.rej
patching file include/configs/meesc.h
Hunk #1 FAILED at 3.
Hunk #2 FAILED at 27.
patch: **** malformed patch@line 116: reworked */
--->8---
a) there is something wrong with your toolchain ... something corupted
the mail (automatic line wrap)
b) the patch is not on top of current master
Andreas
>
> board/esd/meesc/meesc.c | 20 ++++++++++++++++----
> include/configs/meesc.h | 42 ++++++++++++++++++++----------------------
> 2 files changed, 36 insertions(+), 26 deletions(-)
>
> diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
> index c5994e0..b7f9f90 100644
> --- a/board/esd/meesc/meesc.c
> +++ b/board/esd/meesc/meesc.c
> @@ -3,7 +3,7 @@
> * Stelian Pop <stelian@popies.net>
> * Lead Tech Design <www.leadtechdesign.com>
> *
> - * (C) Copyright 2009-2011
> + * (C) Copyright 2009-2015
> * Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
> * esd electronic system design gmbh <www.esd.eu>
> *
> @@ -28,6 +28,7 @@ DECLARE_GLOBAL_DATA_PTR;
> * Miscelaneous platform dependent initialisations
> */
>
> +#ifdef CONFIG_REVISION_TAG
> static int hw_rev = -1; /* hardware revision */
>
> int get_hw_rev(void)
> @@ -45,6 +46,7 @@ int get_hw_rev(void)
>
> return hw_rev;
> }
> +#endif /* CONFIG_REVISION_TAG */
>
> #ifdef CONFIG_CMD_NAND
> static void meesc_nand_hw_init(void)
> @@ -125,12 +127,18 @@ static void meesc_ethercat_hw_init(void)
>
> int dram_init(void)
> {
> - gd->ram_size = get_ram_size(
> - (void *)CONFIG_SYS_SDRAM_BASE,
> - CONFIG_SYS_SDRAM_SIZE);
> + /* dram_init must store complete ramsize in gd->ram_size */
> + gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
> + PHYS_SDRAM_SIZE);
> return 0;
> }
>
> +void dram_init_banksize(void)
> +{
> + gd->bd->bi_dram[0].start = PHYS_SDRAM;
> + gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
> +}
> +
> int board_eth_init(bd_t *bis)
> {
> int rc = 0;
> @@ -140,6 +148,7 @@ int board_eth_init(bd_t *bis)
> return rc;
> }
>
> +#ifdef CONFIG_DISPLAY_BOARDINFO
> int checkboard(void)
> {
> char str[32];
> @@ -173,10 +182,13 @@ int checkboard(void)
> puts(", serial# ");
> puts(str);
> }
> +#ifdef CONFIG_REVISION_TAG
> printf("\nHardware-revision: 1.%d\n", get_hw_rev());
> +#endif
> printf("Mach-type: %lu\n", gd->bd->bi_arch_number);
> return 0;
> }
> +#endif /* CONFIG_DISPLAY_BOARDINFO */
>
> #ifdef CONFIG_SERIAL_TAG
> void get_board_serial(struct tag_serialnr *serialnr)
> diff --git a/include/configs/meesc.h b/include/configs/meesc.h
> index 9c53fb4..10a6ce9 100644
> --- a/include/configs/meesc.h
> +++ b/include/configs/meesc.h
> @@ -3,7 +3,7 @@
> * Stelian Pop <stelian@popies.net>
> * Lead Tech Design <www.leadtechdesign.com>
> *
> - * (C) Copyright 2009-2011
> + * (C) Copyright 2009-2015
> * Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
> * esd electronic system design gmbh <www.esd.eu>
> *
> @@ -27,7 +27,7 @@
> * Since the linker has to swallow that define, we must use a pure
> * hex number here!
> */
> -#define CONFIG_SYS_TEXT_BASE 0x20002000
> +#define CONFIG_SYS_TEXT_BASE 0x21F00000
>
> /*
> * since a number of boards are not being listed in linux
> @@ -56,14 +56,13 @@
> #define CONFIG_DISPLAY_CPUINFO /* display cpu info and speed */
> #define CONFIG_PREBOOT /* enable preboot variable */
>
> +#define CONFIG_CMD_BOOTZ
> +#define CONFIG_OF_LIBFDT
>
> /*
> * Hardware drivers
> */
>
> -/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is
> reworked */
> -#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
> -
> /* general purpose I/O */
> #define CONFIG_AT91_GPIO
>
> @@ -87,10 +86,17 @@
> /*
> * Command line configuration.
> */
> +#undef CONFIG_CMD_BDI
> +#undef CONFIG_CMD_FPGA
> +#undef CONFIG_CMD_LOADS
> +#undef CONFIG_CMD_IMLS
> +
> #define CONFIG_CMD_PING
> #define CONFIG_CMD_DHCP
> +
> +#ifdef CONFIG_SYS_USE_NANDFLASH
> #define CONFIG_CMD_NAND
> -#define CONFIG_CMD_USB
> +#endif
>
> /* LED */
> #define CONFIG_AT91_LED
> @@ -99,9 +105,12 @@
> * SDRAM: 1 bank, min 32, max 128 MB
> * Initialized before u-boot gets started.
> */
> +#define PHYS_SDRAM ATMEL_BASE_CS1 /* 0x20000000 */
> +#define PHYS_SDRAM_SIZE 0x02000000 /* 32 MByte */
> +
> #define CONFIG_NR_DRAM_BANKS 1
> -#define CONFIG_SYS_SDRAM_BASE 0x20000000 /* ATMEL_BASE_CS1 */
> -#define CONFIG_SYS_SDRAM_SIZE 0x02000000
> +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
> +#define CONFIG_SYS_SDRAM_SIZE PHYS_SDRAM_SIZE
>
> #define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x00100000)
> #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01E00000)
> @@ -133,7 +142,7 @@
> #ifdef CONFIG_CMD_NAND
> # define CONFIG_NAND_ATMEL
> # define CONFIG_SYS_MAX_NAND_DEVICE 1
> -# define CONFIG_SYS_NAND_BASE 0x40000000 /* ATMEL_BASE_CS3 */
> +# define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 /* 0x40000000 */
> # define CONFIG_SYS_NAND_DBW_8
> # define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
> # define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
> @@ -148,19 +157,6 @@
> #define CONFIG_NET_RETRY_COUNT 20
> #undef CONFIG_RESET_PHY_R
>
> -/* USB */
> -#define CONFIG_USB_ATMEL
> -#define CONFIG_USB_ATMEL_CLK_SEL_PLLB
> -#define CONFIG_USB_OHCI_NEW
> -#define CONFIG_DOS_PARTITION
> -#define CONFIG_SYS_USB_OHCI_CPU_INIT
> -#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000
> -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
> -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
> -
> -/* CAN */
> -#define CONFIG_AT91_CAN
> -
> /* hw-controller addresses */
> #define CONFIG_ET1100_BASE 0x70000000
>
> @@ -190,6 +186,8 @@
> sizeof(CONFIG_SYS_PROMPT) + 16)
> #define CONFIG_SYS_LONGHELP
> #define CONFIG_CMDLINE_EDITING
> +#define CONFIG_AUTO_COMPLETE
> +#define CONFIG_SYS_HUSH_PARSER
>
> /*
> * Size of malloc() pool
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2015-10-31 20:47 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-10-29 12:38 [U-Boot] [PATCH 1/1] arm: at91: reworked meesc board support Daniel Gorsulowski
2015-10-30 4:44 ` [U-Boot] [PATCH V2 " Daniel Gorsulowski
2015-10-31 20:47 ` Andreas Bießmann
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox