[U-Boot] [PATCH] sunxi: clock: Set AHB1 clock frequency to 200MHz on Allwinner H3

[Hans de Goede <hdegoede@redhat.com>]

Hi,

On 20-11-15 06:07, Siarhei Siamashka wrote:
> The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
> on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
> This can be verified by reading the value of the AHB1_APB1_CFG_REG
> register via /dev/mem. It always reads as 0x3180 regardless of
> the current cpufreq operating point. So this configuration should
> be safe for use in U-Boot too.
>
> PLL6 also needs to be configured before it is used as the clock
> source, according to the "CCU / Programming Guidelines" section
> of the Allwinner manual.
>
> The current low AHB1 clock speed is limiting the USB transfer
> speed when booting via FEL. This patch can increase the FEL USB
> transfer speed from ~510 KB/s to ~950 KB/s.
>
> Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
> ---
>
> This is intended to be used together with the Allwinner H3 patches
> from Jens Kuske:
>      http://lists.denx.de/pipermail/u-boot/2015-November/234589.html

Thanks, I've applied this patch to my tree, and it will be part
of the next pull-req.

Regards,

Hans

>
> Allwinner A83T is likely using the same 200MHz AHB1 setup:
>      https://github.com/allwinner-zh/bootloader/blob/e5ceeca21188/basic_loader/bsp/bsp_for_a83/common/common.c#L101
>
> I can successfully boot my A31s based tablet with 200MHz AHB1 clock
> speed too. And this also speeds up FEL USB transfers. However I can't
> check what kind of AHB1 configuration is used by the Android firmware
> without rooting it first, which I wouldn't do at the moment.
>
>   arch/arm/cpu/armv7/sunxi/clock_sun6i.c        | 6 ++++--
>   arch/arm/include/asm/arch-sunxi/clock_sun6i.h | 7 ++++++-
>   2 files changed, 10 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/cpu/armv7/sunxi/clock_sun6i.c b/arch/arm/cpu/armv7/sunxi/clock_sun6i.c
> index 3ab3b31..916ee48 100644
> --- a/arch/arm/cpu/armv7/sunxi/clock_sun6i.c
> +++ b/arch/arm/cpu/armv7/sunxi/clock_sun6i.c
> @@ -34,9 +34,11 @@ void clock_init_safe(void)
>
>   	clock_set_pll1(408000000);
>
> -	writel(AHB1_ABP1_DIV_DEFAULT, &ccm->ahb1_apb1_div);
> -
>   	writel(PLL6_CFG_DEFAULT, &ccm->pll6_cfg);
> +	while (!(readl(&ccm->pll6_cfg) & CCM_PLL6_CTRL_LOCK))
> +		;
> +
> +	writel(AHB1_ABP1_DIV_DEFAULT, &ccm->ahb1_apb1_div);
>
>   	writel(MBUS_CLK_DEFAULT, &ccm->mbus0_clk_cfg);
>   	writel(MBUS_CLK_DEFAULT, &ccm->mbus1_clk_cfg);
> diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
> index 584d351..09337a1 100644
> --- a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
> +++ b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
> @@ -201,6 +201,7 @@ struct sunxi_ccm_reg {
>   #define CCM_PLL6_CTRL_N_MASK		(0x1f << CCM_PLL6_CTRL_N_SHIFT)
>   #define CCM_PLL6_CTRL_K_SHIFT		4
>   #define CCM_PLL6_CTRL_K_MASK		(0x3 << CCM_PLL6_CTRL_K_SHIFT)
> +#define CCM_PLL6_CTRL_LOCK		(1 << 28)
>
>   #define CCM_MIPI_PLL_CTRL_M_SHIFT	0
>   #define CCM_MIPI_PLL_CTRL_M_MASK	(0xf << CCM_MIPI_PLL_CTRL_M_SHIFT)
> @@ -219,7 +220,11 @@ struct sunxi_ccm_reg {
>   #define CCM_PLL11_CTRL_UPD		(0x1 << 30)
>   #define CCM_PLL11_CTRL_EN		(0x1 << 31)
>
> -#define AHB1_ABP1_DIV_DEFAULT		0x00002020
> +#if defined CONFIG_MACH_SUN8I_H3
> +#define AHB1_ABP1_DIV_DEFAULT		0x00003180 /* AHB1=PLL6/3,APB1=AHB1/2 */
> +#else
> +#define AHB1_ABP1_DIV_DEFAULT		0x00002020 /* AHB1=AXI/4, APB1=AHB1/2 */
> +#endif
>
>   #define AXI_GATE_OFFSET_DRAM		0
>
>