[U-Boot] [PATCH 5/5] move the erratum_a008336_a008514 from general ddr file to soc file

[Sinan Akman <sinan@writeme.com>]

   Hi Yuan

On 26/11/15 02:58 AM, Yuan Yao wrote:
> Both of the erratum:A008336 and A008514 are not apply to all the
> soc like:LS1021A, LS1043A.

   nitpick : perhaps you could reword the commit message to make
it a bit more clear. A suggestion :

   "As the errata A008336 and A008514 do not apply to all LS series
SoCs (such as LS1021A, LS1043A) we move them to an soc specific file"

> So it seems better to move those erratum codes form the general ddr
> file to the private soc file.
>
> Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
> ---
>   arch/arm/cpu/armv8/fsl-layerscape/soc.c | 37 +++++++++++++++++++++++++++++++++
>   drivers/ddr/fsl/fsl_ddr_gen4.c          | 34 ------------------------------
>   2 files changed, 37 insertions(+), 34 deletions(-)
>
> diff --git a/arch/arm/cpu/armv8/fsl-layerscape/soc.c b/arch/arm/cpu/armv8/fsl-layerscape/soc.c
> index 8896b70..738b113 100644
> --- a/arch/arm/cpu/armv8/fsl-layerscape/soc.c
> +++ b/arch/arm/cpu/armv8/fsl-layerscape/soc.c

   Not exactly related to this patch but at this point we have :

   armv7/ls102xa
   armv8/fsl-layerscape

   I think ls102x is also considered a layerscape SoC
and this is potentially confusing. Perhaps in another patch
we can come up with better naming.

   Regards
   Sinan Akman

> @@ -14,6 +14,41 @@
>   DECLARE_GLOBAL_DATA_PTR;
>
>   #if defined(CONFIG_LS2080A) || defined(CONFIG_LS2085A)
> +/*
> + * This erratum requires setting a value to eddrtqcr1 to
> + * optimal the DDR performance.
> + */
> +static void erratum_a008336(void)
> +{
> +	u32 *eddrtqcr1;
> +
> +#ifdef CONFIG_SYS_FSL_ERRATUM_A008336
> +#ifdef CONFIG_SYS_FSL_DCSR_DDR_ADDR
> +	eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR_ADDR + 0x800;
> +	out_le32(eddrtqcr1, 0x63b30002);
> +#endif
> +#ifdef CONFIG_SYS_FSL_DCSR_DDR2_ADDR
> +	eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR2_ADDR + 0x800;
> +	out_le32(eddrtqcr1, 0x63b30002);
> +#endif
> +#endif
> +}
> +
> +/*
> + * This erratum requires a register write before being Memory
> + * controller 3 being enabled.
> + */
> +static void erratum_a008514(void)
> +{
> +	u32 *eddrtqcr1;
> +
> +#ifdef CONFIG_SYS_FSL_ERRATUM_A008514
> +#ifdef CONFIG_SYS_FSL_DCSR_DDR2_ADDR
> +	eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR3_ADDR + 0x800;
> +	out_le32(eddrtqcr1, 0x63b20002);
> +#endif
> +#endif
> +}
>   #ifdef CONFIG_SYS_FSL_ERRATUM_A009635
>   #define PLATFORM_CYCLE_ENV_VAR	"a009635_interval_val"
>
> @@ -118,6 +153,8 @@ void fsl_lsch3_early_init_f(void)
>   	erratum_rcw_src();
>   	init_early_memctl_regs();	/* tighten IFC timing */
>   	erratum_a009203();
> +	erratum_a008514();
> +	erratum_a008336();
>   }
>
>   #elif defined(CONFIG_LS1043A)
> diff --git a/drivers/ddr/fsl/fsl_ddr_gen4.c b/drivers/ddr/fsl/fsl_ddr_gen4.c
> index 50f4671..d7cbf34 100644
> --- a/drivers/ddr/fsl/fsl_ddr_gen4.c
> +++ b/drivers/ddr/fsl/fsl_ddr_gen4.c
> @@ -48,10 +48,6 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
>   	u32 temp_sdram_cfg;
>   	u32 total_gb_size_per_controller;
>   	int timeout;
> -#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
> -	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
> -	u32 *eddrtqcr1;
> -#endif
>   #ifdef CONFIG_SYS_FSL_ERRATUM_A008511
>   	u32 temp32, mr6;
>   	u32 vref_seq1[3] = {0x80, 0x96, 0x16};	/* for range 1 */
> @@ -69,36 +65,20 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
>   	switch (ctrl_num) {
>   	case 0:
>   		ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
> -#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
> -	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
> -		eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR_ADDR + 0x800;
> -#endif
>   		break;
>   #if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 1)
>   	case 1:
>   		ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
> -#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
> -	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
> -		eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR2_ADDR + 0x800;
> -#endif
>   		break;
>   #endif
>   #if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 2)
>   	case 2:
>   		ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
> -#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
> -	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
> -		eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR3_ADDR + 0x800;
> -#endif
>   		break;
>   #endif
>   #if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_NUM_DDR_CONTROLLERS > 3)
>   	case 3:
>   		ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
> -#if defined(CONFIG_SYS_FSL_ERRATUM_A008336) || \
> -	defined(CONFIG_SYS_FSL_ERRATUM_A008514)
> -		eddrtqcr1 = (void *)CONFIG_SYS_FSL_DCSR_DDR4_ADDR + 0x800;
> -#endif
>   		break;
>   #endif
>   	default:
> @@ -109,20 +89,6 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
>   	if (step == 2)
>   		goto step2;
>
> -#ifdef CONFIG_SYS_FSL_ERRATUM_A008336
> -#if defined(CONFIG_LS2080A) || defined(CONFIG_LS2085A)
> -	/* A008336 only applies to general DDR controllers */
> -	if ((ctrl_num == 0) || (ctrl_num == 1))
> -#endif
> -		ddr_out32(eddrtqcr1, 0x63b30002);
> -#endif
> -#ifdef CONFIG_SYS_FSL_ERRATUM_A008514
> -#if defined(CONFIG_LS2080A) || defined(CONFIG_LS2085A)
> -	/* A008514 only applies to DP-DDR controler */
> -	if (ctrl_num == 2)
> -#endif
> -		ddr_out32(eddrtqcr1, 0x63b20002);
> -#endif
>   	if (regs->ddr_eor)
>   		ddr_out32(&ddr->eor, regs->ddr_eor);
>
>