[U-Boot] [PATCH 3/3] serial: uartlite: Add uartlite to Kconfig

[Michal Simek <michal.simek@xilinx.com>]

On 15.12.2015 05:02, Thomas Chou wrote:
> Hi Michal,
> 
> On 2015?12?14? 23:42, Michal Simek wrote:
>> On 14.12.2015 15:35, Thomas Chou wrote:
>>> Hi Michal,
>>>
>>> On 2015?12?11? 19:54, Michal Simek wrote:
>>>> - Move config option out of board file.
>>>> - Remove uartlite address from config file
>>>>
>>>> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
>>>> ---
>>>>
>>>>    board/xilinx/microblaze-generic/xparameters.h | 4 ----
>>>>    configs/microblaze-generic_defconfig          | 1 +
>>>>    drivers/serial/Kconfig                        | 7 +++++++
>>>>    include/configs/microblaze-generic.h          | 7 +------
>>>>    4 files changed, 9 insertions(+), 10 deletions(-)
>>>>
>>>> diff --git a/board/xilinx/microblaze-generic/xparameters.h
>>>> b/board/xilinx/microblaze-generic/xparameters.h
>>>> index 8ba146cb88db..11b3c9a4846e 100644
>>>> --- a/board/xilinx/microblaze-generic/xparameters.h
>>>> +++ b/board/xilinx/microblaze-generic/xparameters.h
>>>> @@ -28,10 +28,6 @@
>>>>    #define XILINX_TIMER_BASEADDR    0x41c00000
>>>>    #define XILINX_TIMER_IRQ    0
>>>>
>>>> -/* Uart pheriphery is RS232_Uart */
>>>> -#define XILINX_UARTLITE_BASEADDR    0x40600000
>>>> -#define XILINX_UARTLITE_BAUDRATE    115200
>>>> -
>>>>    /* IIC pheriphery is IIC_EEPROM */
>>>>    #define XILINX_IIC_0_BASEADDR    0x40800000
>>>>    #define XILINX_IIC_0_FREQ    100000
>>>> diff --git a/configs/microblaze-generic_defconfig
>>>> b/configs/microblaze-generic_defconfig
>>>> index 5df080b6a87c..9a7bb915466f 100644
>>>> --- a/configs/microblaze-generic_defconfig
>>>> +++ b/configs/microblaze-generic_defconfig
>>>> @@ -9,3 +9,4 @@ CONFIG_CMD_GPIO=y
>>>>    # CONFIG_CMD_SETEXPR is not set
>>>>    CONFIG_SPL_OF_CONTROL=y
>>>>    CONFIG_OF_EMBED=y
>>>> +CONFIG_XILINX_UARTLITE=y
>>>> diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
>>>> index f1e221799b81..ddf49ba9cef3 100644
>>>> --- a/drivers/serial/Kconfig
>>>> +++ b/drivers/serial/Kconfig
>>>> @@ -230,4 +230,11 @@ config UNIPHIER_SERIAL
>>>>          If you have a UniPhier based board and want to use the on-chip
>>>>          serial ports, say Y to this option. If unsure, say N.
>>>>
>>>> +config XILINX_UARTLITE
>>>> +    bool "Xilinx Uarlite support"
>>>> +    depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
>>>> +    help
>>>> +      If you have a Xilinx based board and want to use the uartlite
>>>> +      serial ports, say Y to this option. If unsure, say N.
>>>> +
>>>>    endmenu
>>>
>>> Kconfig should be with the driver 1/3. Others are boards related.
>>
>> It can be. Adding Kconfig fragment can be separate patch out of move to
>> DM. There is no connection too.
>> My intention was to show all related changes which are done by this one
>> step.
> 
> Please also make sure the patch series are bisectable.

I am not aware about anything what would caused that this series is not
bisectable. Do you see something like that?

Thanks,
Michal