From: Purna Chandra Mandal <purna.mandal@microchip.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v1 11/18] drivers: gpio: add driver for Microchip PIC32 GPIO controller.
Date: Thu, 17 Dec 2015 23:01:45 +0530 [thread overview]
Message-ID: <5672F181.9050201@microchip.com> (raw)
PIC32 has ten independently programmable ports and each one with 16 pins.
These pins can be configured and used as GPIO, if they are not used by
any other peripherals.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
---
drivers/gpio/Kconfig | 7 ++
drivers/gpio/Makefile | 2 +-
drivers/gpio/pic32_gpio.c | 164 ++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 172 insertions(+), 1 deletion(-)
create mode 100644 drivers/gpio/pic32_gpio.c
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index e60e9fd..13e9a6a 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -83,4 +83,11 @@ config VYBRID_GPIO
help
Say yes here to support Vybrid vf610 GPIOs.
+config PIC32_GPIO
+ bool "Microchip PIC32 GPIO driver"
+ depends on DM_GPIO
+ default y if MACH_PIC32
+ help
+ Say yes here to support Microchip PIC32 GPIOs.
+
endmenu
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index fb4fd25..845a6d4 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -46,4 +46,4 @@ obj-$(CONFIG_STM32_GPIO) += stm32_gpio.o
obj-$(CONFIG_ZYNQ_GPIO) += zynq_gpio.o
obj-$(CONFIG_VYBRID_GPIO) += vybrid_gpio.o
obj-$(CONFIG_HIKEY_GPIO) += hi6220_gpio.o
-
+obj-$(CONFIG_PIC32_GPIO) += pic32_gpio.o
diff --git a/drivers/gpio/pic32_gpio.c b/drivers/gpio/pic32_gpio.c
new file mode 100644
index 0000000..60b423e
--- /dev/null
+++ b/drivers/gpio/pic32_gpio.c
@@ -0,0 +1,164 @@
+/*
+ * Copyright (c) 2015 Microchip Technology Inc
+ * Purna Chandra Mandal <purna.mandal@microchip.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <malloc.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <linux/compat.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <asm/arch-pic32/pic32.h>
+
+/* Peripheral Pin Control */
+struct pic32_gpio_regs {
+ struct pic32_reg_atomic ansel;
+ struct pic32_reg_atomic tris;
+ struct pic32_reg_atomic port;
+ struct pic32_reg_atomic lat;
+ struct pic32_reg_atomic open_drain;
+ struct pic32_reg_atomic cnpu;
+ struct pic32_reg_atomic cnpd;
+ struct pic32_reg_atomic cncon;
+};
+
+enum {
+ MICROCHIP_GPIO_DIR_OUT,
+ MICROCHIP_GPIO_DIR_IN,
+ MICROCHIP_GPIOS_PER_BANK = 16,
+};
+
+struct pic32_gpio_priv {
+ struct pic32_gpio_regs *regs;
+ char name[2];
+};
+
+static int pic32_gpio_get_value(struct udevice *dev, unsigned offset)
+{
+ struct pic32_gpio_priv *priv = dev_get_priv(dev);
+
+ return !!(readl(&priv->regs->port.raw) & BIT(offset));
+}
+
+static int pic32_gpio_set_value(struct udevice *dev, unsigned offset,
+ int value)
+{
+ struct pic32_gpio_priv *priv = dev_get_priv(dev);
+ int mask = BIT(offset);
+
+ if (value)
+ writel(mask, &priv->regs->port.set);
+ else
+ writel(mask, &priv->regs->port.clr);
+
+ return 0;
+}
+
+static int pic32_gpio_direction(struct udevice *dev, unsigned offset)
+{
+ struct pic32_gpio_priv *priv = dev_get_priv(dev);
+
+ if (readl(&priv->regs->ansel.raw) & BIT(offset))
+ return -1;
+
+ if (readl(&priv->regs->tris.raw) & BIT(offset))
+ return MICROCHIP_GPIO_DIR_IN;
+ else
+ return MICROCHIP_GPIO_DIR_OUT;
+}
+
+static int pic32_gpio_direction_input(struct udevice *dev, unsigned offset)
+{
+ struct pic32_gpio_priv *priv = dev_get_priv(dev);
+ int mask = BIT(offset);
+
+ writel(mask, &priv->regs->ansel.clr);
+ writel(mask, &priv->regs->tris.set);
+
+ return 0;
+}
+
+static int pic32_gpio_direction_output(struct udevice *dev,
+ unsigned offset, int value)
+{
+ struct pic32_gpio_priv *priv = dev_get_priv(dev);
+ int mask = BIT(offset);
+
+ writel(mask, &priv->regs->ansel.clr);
+ writel(mask, &priv->regs->tris.clr);
+
+ pic32_gpio_set_value(dev, offset, value);
+ return 0;
+}
+
+static int pic32_gpio_xlate(struct udevice *dev, struct gpio_desc *desc,
+ struct fdtdec_phandle_args *args)
+{
+ desc->offset = args->args[0];
+ desc->flags = args->args[1] & GPIO_ACTIVE_LOW ? GPIOD_ACTIVE_LOW : 0;
+
+ return 0;
+}
+
+static int pic32_gpio_probe(struct udevice *dev)
+{
+ struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+ struct pic32_gpio_priv *priv = dev_get_priv(dev);
+ char *end;
+ int bank;
+
+ priv->regs = (struct pic32_gpio_regs *)dev_get_addr(dev);
+ uc_priv->gpio_count = MICROCHIP_GPIOS_PER_BANK;
+ end = strrchr(dev->name, '@');
+ bank = trailing_strtoln(dev->name, end);
+ priv->name[0] = 'A' + bank;
+ uc_priv->bank_name = priv->name;
+
+ return 0;
+}
+
+static int pic32_gpio_get_function(struct udevice *dev, unsigned offset)
+{
+ int ret = GPIOF_UNUSED;
+
+ switch (pic32_gpio_direction(dev, offset)) {
+ case MICROCHIP_GPIO_DIR_OUT:
+ ret = GPIOF_OUTPUT;
+ break;
+ case MICROCHIP_GPIO_DIR_IN:
+ ret = GPIOF_INPUT;
+ break;
+ default:
+ ret = GPIOF_UNUSED;
+ break;
+ }
+ return ret;
+}
+
+static const struct dm_gpio_ops gpio_pic32_ops = {
+ .direction_input = pic32_gpio_direction_input,
+ .direction_output = pic32_gpio_direction_output,
+ .get_value = pic32_gpio_get_value,
+ .set_value = pic32_gpio_set_value,
+ .get_function = pic32_gpio_get_function,
+ .xlate = pic32_gpio_xlate,
+};
+
+static const struct udevice_id pic32_gpio_ids[] = {
+ { .compatible = "microchip,gpio-bank" },
+ { }
+};
+
+U_BOOT_DRIVER(gpio_pic32) = {
+ .name = "gpio_pic32",
+ .id = UCLASS_GPIO,
+ .of_match = pic32_gpio_ids,
+ .ops = &gpio_pic32_ops,
+ .probe = pic32_gpio_probe,
+ .priv_auto_alloc_size = sizeof(struct pic32_gpio_priv),
+};
--
1.8.3.1
reply other threads:[~2015-12-17 17:31 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5672F181.9050201@microchip.com \
--to=purna.mandal@microchip.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox