From: York Sun <yorksun@freescale.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 16/17] arm: ls1021atwr: Disable CONFIG_E1000 temporarily
Date: Tue, 12 Jan 2016 09:52:13 -0800 [thread overview]
Message-ID: <56953D4D.9070302@freescale.com> (raw)
In-Reply-To: <1452580888-27637-17-git-send-email-bmeng.cn@gmail.com>
On 01/11/2016 10:38 PM, Bin Meng wrote:
> Before we switch to use driver model ethernet support, disable
> CONFIG_E1000 temporarily as with driver model ethernet, E1000
> driver depends on driver model PCI which is not ready on this
> board yet.
>
Any idea when PCI/E1000 can be enabled?
York
next prev parent reply other threads:[~2016-01-12 17:52 UTC|newest]
Thread overview: 57+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-01-12 6:41 [U-Boot] [PATCH 00/17] arm: ls1021atwr: Convert to use driver model TSEC driver Bin Meng
2016-01-12 6:41 ` [U-Boot] [PATCH 01/17] powerpc: bsc9132qds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENET Bin Meng
2016-01-27 15:07 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 02/17] powerpc: c29xpcie: " Bin Meng
2016-01-27 15:08 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 03/17] powerpc: mpc8572ds: " Bin Meng
2016-01-27 15:08 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 04/17] powerpc: mpc8548cds: " Bin Meng
2016-01-27 15:08 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 05/17] powerpc: p1010rdb: " Bin Meng
2016-01-27 15:08 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 06/17] arm: ls1021atwr: " Bin Meng
2016-01-27 15:09 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 07/17] net: tsec: fsl_mdio: Fix several cosmetic issues Bin Meng
2016-01-27 15:11 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 08/17] net: tsec: Move rx_idx and tx_idx to struct tsec_private Bin Meng
2016-01-27 15:13 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 09/17] net: tsec: Move rxbd and txbd " Bin Meng
2016-01-27 15:15 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 10/17] net: tsec: Adjust orders to avoid forward declaration of tsec_send() Bin Meng
2016-01-27 15:15 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 11/17] net: tsec: Use tsec_private pointer as the parameter for internal routines Bin Meng
2016-01-27 15:16 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 12/17] doc: dt-bindings: Describe Freescale TSEC ethernet controller Bin Meng
2016-01-27 15:17 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 13/17] net: tsec: Add driver model ethernet support Bin Meng
2016-01-13 20:09 ` Simon Glass
2016-01-27 15:19 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 14/17] net: tsec: Use priv->tbiaddr to initialize TBI PHY address Bin Meng
2016-01-27 15:20 ` Joe Hershberger
2016-01-29 21:26 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 15/17] arm: ls102xa: Rewrite the logic of ft_fixup_enet_phy_connect_type() Bin Meng
2016-01-27 15:21 ` Joe Hershberger
2016-01-29 21:27 ` [U-Boot] " Joe Hershberger
2016-01-12 6:41 ` [U-Boot] [PATCH 16/17] arm: ls1021atwr: Disable CONFIG_E1000 temporarily Bin Meng
2016-01-12 17:52 ` York Sun [this message]
2016-01-13 6:21 ` Bin Meng
2016-01-13 16:07 ` york sun
2016-01-14 1:57 ` Bin Meng
2016-01-12 6:41 ` [U-Boot] [PATCH 17/17] arm: ls1021atwr: Convert to use driver model TSEC driver Bin Meng
2016-01-18 5:16 ` [U-Boot] [PATCH 00/17] " Bin Meng
2016-01-19 17:16 ` york sun
2016-01-26 2:45 ` Bin Meng
2016-01-27 15:26 ` Joe Hershberger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56953D4D.9070302@freescale.com \
--to=yorksun@freescale.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox