* [U-Boot] [REGRESSION] Ethernet broken on Colibri T20/T30
@ 2016-01-17 0:51 Marcel Ziswiler
2016-01-18 17:42 ` Stephen Warren
0 siblings, 1 reply; 3+ messages in thread
From: Marcel Ziswiler @ 2016-01-17 0:51 UTC (permalink / raw)
To: u-boot
Hi Simon
As mentioned before I noticed Ethernet (on-module USB ASIX chip) to be
broken on master while it still worked fine in v2016.01. I kind of
remember having once noticed something along those lines when testing
some of your early dm stuff but could not find our discussion about it
anymore plus I don't think it did actually lead anywhere.
FWIW it currently crashes as follows (showing Colibri T20 but the same
happens on Colibri T30):
U-Boot SPL 2016.01-00205-gb8c5b47 (Jan 17 2016 - 01:31:48)
Trying to boot from RAM
U-Boot 2016.01-00205-gb8c5b47 (Jan 17 2016 - 01:31:48 +0100)
TEGRA20
Model: Toradex Colibri T20
Board: Toradex Colibri T20
DRAM:??512 MiB
NAND:??1024 MiB
MMC:???Tegra SD/MMC: 0
*** Warning - bad CRC, using default environment
In:????serial
Out:???lcd
Err:???lcd
USB recovery mode
Net:???No ethernet found.
Hit any key to stop autoboot:??2 \b\b\b 0?
Colibri T20 # usb start
starting USB...
USB0:???USB EHCI 1.00
USB1:???USB EHCI 1.00
USB2:???USB EHCI 1.00
scanning bus 1 for devices... 1 USB Device(s) found
scanning bus 2 for devices...?
Warning: asix_eth using MAC address from ROM
2 USB Device(s) found
scanning bus 0 for devices... 2 USB Device(s) found
Colibri T20 # dhcp
BOOTP broadcast 1
EHCI timed out on TD - token=0x88008d80
Rx: failed to receive: -5
BOOTP broadcast 2
EHCI timed out on TD - token=0x8008d80
Rx: failed to receive: -5
BOOTP broadcast 3
EHCI timed out on TD - token=0x88008d80
Rx: failed to receive: -5
BOOTP broadcast 4
EHCI timed out on TD - token=0x8008d80
Rx: failed to receive: -5
BOOTP broadcast 5
EHCI timed out on TD - token=0x88008d80
Rx: failed to receive: -5
BOOTP broadcast 6
EHCI timed out on TD - token=0x8008d80
Rx: failed to receive: -5
Retry time exceeded; starting again
data abort
pc : [<1fb4d194>] ???lr : [<1fbb9784>]
reloc pc : [<0012d194>] ???lr : [<00199784>]
sp : 1d61c5e0??ip : 6aa665ea ?fp : 1d62bca0
r10: 00000000??r9 : 1d61fee0 ?r8 : 1d62bca0
r7 : 00000000??r6 : 1d6312e0 ?r5 : 1f6da8e0??r4 : 00000000
r3 : 1c585760??r2 : 03155180 ?r1 : 00000000??r0 : caa661ca
Flags: NzCv??IRQs off??FIQs off??Mode SVC_32
Resetting CPU ...
resetting ...
Do you have any clue what could be going on?
Cheers
Marcel
^ permalink raw reply [flat|nested] 3+ messages in thread
* [U-Boot] [REGRESSION] Ethernet broken on Colibri T20/T30
2016-01-17 0:51 [U-Boot] [REGRESSION] Ethernet broken on Colibri T20/T30 Marcel Ziswiler
@ 2016-01-18 17:42 ` Stephen Warren
2016-01-19 2:13 ` Simon Glass
0 siblings, 1 reply; 3+ messages in thread
From: Stephen Warren @ 2016-01-18 17:42 UTC (permalink / raw)
To: u-boot
On 01/16/2016 05:51 PM, Marcel Ziswiler wrote:
> Hi Simon
>
> As mentioned before I noticed Ethernet (on-module USB ASIX chip) to be
> broken on master while it still worked fine in v2016.01. I kind of
> remember having once noticed something along those lines when testing
> some of your early dm stuff but could not find our discussion about it
> anymore plus I don't think it did actually lead anywhere.
>
> FWIW it currently crashes as follows (showing Colibri T20 but the same
> happens on Colibri T30):
>
> U-Boot SPL 2016.01-00205-gb8c5b47 (Jan 17 2016 - 01:31:48)
...
> Colibri T20 # usb start
> starting USB...
> USB0: USB EHCI 1.00
> USB1: USB EHCI 1.00
> USB2: USB EHCI 1.00
> scanning bus 1 for devices... 1 USB Device(s) found
> scanning bus 2 for devices...
> Warning: asix_eth using MAC address from ROM
> 2 USB Device(s) found
> scanning bus 0 for devices... 2 USB Device(s) found
> Colibri T20 # dhcp
> BOOTP broadcast 1
> EHCI timed out on TD - token=0x88008d80
> Rx: failed to receive: -5
> BOOTP broadcast 2
> EHCI timed out on TD - token=0x8008d80
> Rx: failed to receive: -5
> BOOTP broadcast 3
> EHCI timed out on TD - token=0x88008d80
> Rx: failed to receive: -5
> BOOTP broadcast 4
> EHCI timed out on TD - token=0x8008d80
> Rx: failed to receive: -5
> BOOTP broadcast 5
> EHCI timed out on TD - token=0x88008d80
> Rx: failed to receive: -5
> BOOTP broadcast 6
> EHCI timed out on TD - token=0x8008d80
> Rx: failed to receive: -5
>
> Retry time exceeded; starting again
> data abort
> pc : [<1fb4d194>] lr : [<1fbb9784>]
> reloc pc : [<0012d194>] lr : [<00199784>]
> sp : 1d61c5e0 ip : 6aa665ea fp : 1d62bca0
> r10: 00000000 r9 : 1d61fee0 r8 : 1d62bca0
> r7 : 00000000 r6 : 1d6312e0 r5 : 1f6da8e0 r4 : 00000000
> r3 : 1c585760 r2 : 03155180 r1 : 00000000 r0 : caa661ca
> Flags: NzCv IRQs off FIQs off Mode SVC_32
> Resetting CPU ...
>
> resetting ...
>
> Do you have any clue what could be going on?
FWIW, I tried that same commit on Beaver with an asix USB Ethernet
device and didn't see that problem, even after aligning the config file
for Beaver more closely with colibri_t30 (e.g. disabling PCIe support,
copying all the config options that colibri_t30 has but beaver doesn't
into beaver's config file).
I wonder if it's anything to do with having 3 USB controllers active
rather than 2 (although that seems unlikely; I can see going from 1->2
causing issues, but once 2 work, adding more seems like it should).
Perhaps there's a DRAM bandwidth issue, but then I can't see why the
patches between v2016.01 and the commit you mentioned would affect that.
^ permalink raw reply [flat|nested] 3+ messages in thread
* [U-Boot] [REGRESSION] Ethernet broken on Colibri T20/T30
2016-01-18 17:42 ` Stephen Warren
@ 2016-01-19 2:13 ` Simon Glass
0 siblings, 0 replies; 3+ messages in thread
From: Simon Glass @ 2016-01-19 2:13 UTC (permalink / raw)
To: u-boot
Hi,
On 18 January 2016 at 10:42, Stephen Warren <swarren@wwwdotorg.org> wrote:
> On 01/16/2016 05:51 PM, Marcel Ziswiler wrote:
>>
>> Hi Simon
>>
>> As mentioned before I noticed Ethernet (on-module USB ASIX chip) to be
>> broken on master while it still worked fine in v2016.01. I kind of
>> remember having once noticed something along those lines when testing
>> some of your early dm stuff but could not find our discussion about it
>> anymore plus I don't think it did actually lead anywhere.
>>
>> FWIW it currently crashes as follows (showing Colibri T20 but the same
>> happens on Colibri T30):
>>
>> U-Boot SPL 2016.01-00205-gb8c5b47 (Jan 17 2016 - 01:31:48)
>
> ...
>
>> Colibri T20 # usb start
>> starting USB...
>> USB0: USB EHCI 1.00
>> USB1: USB EHCI 1.00
>> USB2: USB EHCI 1.00
>> scanning bus 1 for devices... 1 USB Device(s) found
>> scanning bus 2 for devices...
>> Warning: asix_eth using MAC address from ROM
>> 2 USB Device(s) found
>> scanning bus 0 for devices... 2 USB Device(s) found
>> Colibri T20 # dhcp
>> BOOTP broadcast 1
>> EHCI timed out on TD - token=0x88008d80
>> Rx: failed to receive: -5
>> BOOTP broadcast 2
>> EHCI timed out on TD - token=0x8008d80
>> Rx: failed to receive: -5
>> BOOTP broadcast 3
>> EHCI timed out on TD - token=0x88008d80
>> Rx: failed to receive: -5
>> BOOTP broadcast 4
>> EHCI timed out on TD - token=0x8008d80
>> Rx: failed to receive: -5
>> BOOTP broadcast 5
>> EHCI timed out on TD - token=0x88008d80
>> Rx: failed to receive: -5
>> BOOTP broadcast 6
>> EHCI timed out on TD - token=0x8008d80
>> Rx: failed to receive: -5
>>
>> Retry time exceeded; starting again
>> data abort
>> pc : [<1fb4d194>] lr : [<1fbb9784>]
>> reloc pc : [<0012d194>] lr : [<00199784>]
>> sp : 1d61c5e0 ip : 6aa665ea fp : 1d62bca0
>> r10: 00000000 r9 : 1d61fee0 r8 : 1d62bca0
>> r7 : 00000000 r6 : 1d6312e0 r5 : 1f6da8e0 r4 : 00000000
>> r3 : 1c585760 r2 : 03155180 r1 : 00000000 r0 : caa661ca
>> Flags: NzCv IRQs off FIQs off Mode SVC_32
>> Resetting CPU ...
>>
>> resetting ...
>>
>> Do you have any clue what could be going on?
>
>
> FWIW, I tried that same commit on Beaver with an asix USB Ethernet device
> and didn't see that problem, even after aligning the config file for Beaver
> more closely with colibri_t30 (e.g. disabling PCIe support, copying all the
> config options that colibri_t30 has but beaver doesn't into beaver's config
> file).
>
> I wonder if it's anything to do with having 3 USB controllers active rather
> than 2 (although that seems unlikely; I can see going from 1->2 causing
> issues, but once 2 work, adding more seems like it should). Perhaps there's
> a DRAM bandwidth issue, but then I can't see why the patches between
> v2016.01 and the commit you mentioned would affect that.
I have seen the EHCI timeout on and off. I thought it might be due to
cache misalignment such that we wail to talk to the hardware. I have
never dug into it though, or at least not successfully. If you have a
repeatable case it might be worth taking a look.
Regards,
Simon
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2016-01-19 2:13 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-01-17 0:51 [U-Boot] [REGRESSION] Ethernet broken on Colibri T20/T30 Marcel Ziswiler
2016-01-18 17:42 ` Stephen Warren
2016-01-19 2:13 ` Simon Glass
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox