[U-Boot] [PATCH v3 00/21] Add support for 96boards Dragonboard410C board

[U-Boot] [PATCH v3 00/21] Add support for 96boards Dragonboard410C board

[Mateusz Kulikowski]

Hi All,

This is (hopefully) last version of Dragonboard410c series.
Sorry for longer delay, but I had too many things to do recently.

As always - for "simplicity" this series is available on my github:
https://github.com/hallor/u-boot/tree/dragonboard-for-mainline-v3

There are almost no changes + one bugfix:
- Bugfix: small rework of serial driver - U-Boot was interrupted
  when no serial converter was attached.
- Updated dragonboard readme.txt with info on how to stop @ fastboot
- Added SPMI entries into test.dts (so automatic DM tests would not fail)
- Added Tested-by and Reviewed-by Simon (from v2 comments)
- Rebased to recent master
- Fixed warnings in ASIX and ULPI code
- Added comments to head.S, little updates suggested by Daniel

@Simon: Thanks for the tests of v2!

Daniel Gl?ckner, Tom Rini, Jagan Teki: Thanks for the comments!

Regards,
Mateusz

V2 cover contents:

This is updated series. 99% of review changes are applied,
specific changes are (as always) include in each patch.

You can find this series on my github (if anyone just want to
try it - that branch has also wait_for_bit applied):
https://github.com/hallor/u-boot/tree/dragonboard-for-mainline-v2

I did target tests on Dragonboard410c, and build tested
platforms that may be affected by ULPI changes.

@Simon:
I decided not to rewrite pm8916_gpio for now, but for sake of
"cleannes" moved offending bindings to separate file (and
they are now properly childs of pm8916_gpio).
I will update it during rework of SoC gpio driver
(I will have to create proper pinmux/pinctrl drivers to
get rid of Little Kernel eventually).

This series still needs wait_for_bit series that is not
included (yet).

V1 cover contents:

I finally managed to cleanup RFC for submission. I've included changes in
each patch, there is a bit of them, but all are needed :)

This series requires wait_for_bit patch that I send few days ago:
https://patchwork.ozlabs.org/patch/561185/

RFC cover contents:
http://lists.denx.de/pipermail/u-boot/2015-December/237365.html

Changes in v3:
- Add msm_serial_fetch that tries to fetch characters from FIFO
- Decrease no of characters requested in RX transaction
- Try to fetch characters from FIFO when tstc()/pending() is called
- New patch
- New patch
- New patch
- Updated test.dts to include SPMI like sandbox.dts does
- readme: Added info on how to enter fastboot mode and that
  dtbTool is also part of skales. Added more explanation
  on image generation.
- head: Add comment why it's needed, drop MZ EFI signature
  that makes no sense on this particular SoC, fix confusing
  entry point name (+update .lds file)

Changes in v2:
- Added newline before return... (globally)
- Renamed p to priv (priv data) - it required some rewrapping
- Added Reviewed-by
- Reordered includes (again)
- Added newlines between returns
- Fixed error handling in msm_gpio_probe
- Added reviewed-by
- Add reviewed-by
- Add Reviewed-by (sjg)
- Add better (any) descriptions for Kconfig items.
- New patch, independent of the rest
- Should compile cleanly on all affected platforms
- Is orthogonal to series (i.e. if get's NAK will not break rest of series)
- Add acked-by
- Add reviewed-by
- Add Acked-by
- Use PORT_... macro to write to portsc
- Remove extra whitespace in probe()
- Add acked-by
- Use proper  entry order in Kconfig
- Rename CONFIG_DM_SPMI -> CONFIG_SPMI
- Fix header ordering
- Add reviewed-by
- Rename CONFIG_DM_SPMI -> CONFIG_SPMI
- Rename r -> regs, p -> priv
- Add reviewed-by
- Update binding doc (drop unused bindig)
- Rename DM_SPMI -> SPMI
- Rename p -> priv (in write/read)
- Fix header ordering (again)
- Add reviewed-by
- Add reviewed-by
- Reordered Kconfig & Makefile (to keep alphabetical ordering)
- Added link to dt binding @ help
- Add Reviewed-by
- Rename DM_SPMI -> SPMI
- Make MND divider comments more compact :)
- p -> priv
- Add reviewed-by
- Reordered Kconfig to keep alphabetical order
- Renamed reset_sandbox -> msm_reset (typo in reset.c)
- Renamed CONFIG_DM_SPMI -> CONFIG_SPMI
- Removed extra enter in dragonboard file
- Added ULPI* to defconfig
- Added MAINTAINERS to board
- Cleaned up config file - use distro defaults/environment:
  - Dropped multiple CONFIG_CMD* and other CONFIG_*
  - Added distro env/config
  - Dropped old boot commands
- Split dts - pm8916_gpio entries are taken directly from
  Linux Dragonboard dts; Add handles for u-boot in -uboot.dtsi;
  They will be removed once gpio drivers are converted to pinctrl.
- Renamed some pmic nodes, fixed dragonboard.c to find them properly.
- Added header and converted comments to c98-style in head.S
- Print error if pmic gpio node is not found.
- New patch

Changes in v1:
- Added (better) help to KConfig
- Added dt binding documentation
- Fixed include ordering
- Reworked msm_serial_getc
- Added error handling to msm_uart_clk_init (that is ignored later for now)
- Dropped unneeded DM_FLAG_PRE_RELOC
- Added dt binding documentation
- Added help to KConfig
- Use clrsetbits() to switch direction
- Fixed include order
- Added #defines for registers/register fields
- Added secondary compatible string
- Added commit message
- Added DT binding documentation
- Added Kconfig help
- Reordered includes
- Dropped redundant fields from msm_sdhc
- Cleaned up clock init code (+ added error handling)
- Dropped mdelay - use wait_for_bit instead in reset code
- Added missing newline after declarations
- Added error handling if "reg" is missing
- Converted base address to pointer
- No changes, just added Acked-by, Reviewed-by
- Reordered header files
- Removed braces around constant
- Added more verbose help to KConfig
- Added ULPI dependency to Kconfig
- Drop register #defines - use ehci-ci.h instead
- Create fixed ulpi viewport for device
- Use setbits/clearbits where possible
- Use wait_for_bit to reset controller
- Add dt binding documents
- Reorder includes
- Add read/write arguments documentation
- add binding documentation and better Kconfig help
- Changed a bit mapping
- Change include order
- Use clrsetbits* where possible
- Add one more supported dts id
- Handle missing fields in dt properly
- Added dt bindings
- Reoder includes
- Replaced extract_* macros with ordinary shift/mask
- Added error checking and whitespaces in probe
- Add binding doc
- Fixed inlcude ordering
- Merged direction_input and direction_output functions
- gpio_get: use switch instead of stacked if
- use pmic_clrsetbits
- add possibility to change prwkey bank name
- Handle invalid bindings
- Sanity HW check (i.e. check type/subtype registers)
- Fix include order
- Cleanup defines (added spaces for readibility)
- Base address is integer to avoid casting
- Use setbits_* family where possible
- Drop unneded comments, added newlines where needed
- Check return value of dev_get_addr
- Add binding for apq8016
- Cleaned up divider calculation
- Drop most of gpio.h (only empty file is needed)
- Add better help for dragonboard
- Move static structures to board_prepare_usb
- Add DM_SPMI to defconfig

Mateusz Kulikowski (21):
  serial: Add support for Qualcomm serial port
  gpio: Add support for Qualcomm gpio controller
  mmc: Add support for Qualcomm SDHCI controller
  ehci-hcd: Add init_after_reset
  usb: ulpi: Add Kconfig options for ULPI
  Migrate CONFIG_ULPI* to Kconfig
  usb: ulpi: Fix viewport_addr type
  usb: ulpi: Fix compile warning in read/write on 64-bit machines.
  eth: asix88179: Print packet length properly
  usb: Rename ehci-fsl.h to ehci-ci.h
  usb: ehci-ci: Add missing registers.
  ehci-ci.h: drop generic USBCMD fields
  ehci: Add support for Qualcomm EHCI
  drivers: Add SPMI bus uclass
  spmi: Add sandbox test driver
  drivers: spmi: Add support for Qualcomm SPMI bus driver
  pmic: Add support for Qualcomm PM8916 PMIC
  gpio: Add support for Qualcomm PM8916 gpios
  arm: Add support for Qualcomm Snapdragon family
  board: Add Qualcomm Dragonboard 410C support
  Add myself as Snapdragon and SPMI maintainer

 MAINTAINERS                                        |  11 +
 arch/arm/Kconfig                                   |  12 +
 arch/arm/Makefile                                  |   1 +
 arch/arm/dts/Makefile                              |   2 +
 arch/arm/dts/dragonboard410c-uboot.dtsi            |  28 ++
 arch/arm/dts/dragonboard410c.dts                   | 148 ++++++++++
 arch/arm/mach-snapdragon/Kconfig                   |  26 ++
 arch/arm/mach-snapdragon/Makefile                  |   8 +
 arch/arm/mach-snapdragon/clock-apq8016.c           | 262 ++++++++++++++++++
 arch/arm/mach-snapdragon/include/mach/gpio.h       |   9 +
 .../mach-snapdragon/include/mach/sysmap-apq8016.h  |  14 +
 arch/arm/mach-snapdragon/reset.c                   |  40 +++
 arch/sandbox/dts/sandbox.dts                       |  20 ++
 arch/sandbox/dts/test.dts                          |  20 ++
 board/qualcomm/dragonboard410c/Kconfig             |  15 +
 board/qualcomm/dragonboard410c/MAINTAINERS         |   6 +
 board/qualcomm/dragonboard410c/Makefile            |   8 +
 board/qualcomm/dragonboard410c/dragonboard410c.c   | 131 +++++++++
 board/qualcomm/dragonboard410c/head.S              |  34 +++
 board/qualcomm/dragonboard410c/readme.txt          |  71 +++++
 board/qualcomm/dragonboard410c/u-boot.lds          |  90 ++++++
 configs/colibri_t20_defconfig                      |   2 +
 configs/dragonboard410c_defconfig                  |  31 +++
 configs/harmony_defconfig                          |   2 +
 configs/mcx_defconfig                              |   3 +
 configs/mt_ventoux_defconfig                       |   3 +
 configs/sandbox_defconfig                          |   4 +
 configs/twister_defconfig                          |   3 +
 configs/zynq_picozed_defconfig                     |   3 +
 configs/zynq_zc702_defconfig                       |   3 +
 configs/zynq_zc706_defconfig                       |   3 +
 configs/zynq_zed_defconfig                         |   3 +
 configs/zynq_zybo_defconfig                        |   3 +
 doc/device-tree-bindings/gpio/gpio-msm.txt         |  22 ++
 doc/device-tree-bindings/gpio/pm8916_gpio.txt      |  48 ++++
 doc/device-tree-bindings/mmc/msm_sdhci.txt         |  25 ++
 doc/device-tree-bindings/pmic/pm8916.txt           |  18 ++
 doc/device-tree-bindings/serial/msm-serial.txt     |   6 +
 doc/device-tree-bindings/spmi/spmi-msm.txt         |  26 ++
 doc/device-tree-bindings/spmi/spmi-sandbox.txt     |  31 +++
 doc/device-tree-bindings/usb/ehci-msm.txt          |  10 +
 doc/git-mailrc                                     |   3 +
 drivers/Kconfig                                    |   2 +
 drivers/Makefile                                   |   1 +
 drivers/gpio/Kconfig                               |  24 ++
 drivers/gpio/Makefile                              |   2 +
 drivers/gpio/msm_gpio.c                            | 135 +++++++++
 drivers/gpio/pm8916_gpio.c                         | 302 +++++++++++++++++++++
 drivers/mmc/Kconfig                                |   9 +
 drivers/mmc/Makefile                               |   1 +
 drivers/mmc/msm_sdhci.c                            | 180 ++++++++++++
 drivers/power/pmic/Kconfig                         |  16 ++
 drivers/power/pmic/Makefile                        |   1 +
 drivers/power/pmic/pm8916.c                        |  96 +++++++
 drivers/serial/Kconfig                             |   8 +
 drivers/serial/Makefile                            |   1 +
 drivers/serial/serial_msm.c                        | 217 +++++++++++++++
 drivers/spmi/Kconfig                               |  23 ++
 drivers/spmi/Makefile                              |   9 +
 drivers/spmi/spmi-msm.c                            | 189 +++++++++++++
 drivers/spmi/spmi-sandbox.c                        | 157 +++++++++++
 drivers/spmi/spmi-uclass.c                         |  48 ++++
 drivers/usb/Kconfig                                |   2 +
 drivers/usb/eth/asix88179.c                        |   2 +-
 drivers/usb/host/Kconfig                           |  11 +
 drivers/usb/host/Makefile                          |   1 +
 drivers/usb/host/ehci-fsl.c                        |   2 +-
 drivers/usb/host/ehci-hcd.c                        |   6 +
 drivers/usb/host/ehci-mpc512x.c                    |   6 +-
 drivers/usb/host/ehci-msm.c                        | 178 ++++++++++++
 drivers/usb/host/ehci-mx5.c                        |   2 +-
 drivers/usb/host/ehci-mx6.c                        |   2 +-
 drivers/usb/host/ehci-mxc.c                        |   2 +-
 drivers/usb/host/ehci-vf.c                         |   2 +-
 drivers/usb/host/ehci-zynq.c                       |   2 +-
 drivers/usb/host/ehci.h                            |   1 +
 drivers/usb/ulpi/Kconfig                           |  33 +++
 drivers/usb/ulpi/ulpi-viewport.c                   |   5 +-
 include/configs/colibri_t20.h                      |   3 +-
 include/configs/dragonboard410c.h                  | 153 +++++++++++
 include/configs/harmony.h                          |   2 -
 include/configs/mcx.h                              |   2 -
 include/configs/tam3517-common.h                   |   2 -
 include/configs/zynq-common.h                      |   2 -
 include/dm/uclass-id.h                             |   1 +
 include/spmi/spmi.h                                |  47 ++++
 include/usb/{ehci-fsl.h => ehci-ci.h}              |  16 +-
 include/usb/ulpi.h                                 |   4 +-
 test/dm/Makefile                                   |   1 +
 test/dm/spmi.c                                     | 115 ++++++++
 90 files changed, 3203 insertions(+), 31 deletions(-)
 create mode 100644 arch/arm/dts/dragonboard410c-uboot.dtsi
 create mode 100644 arch/arm/dts/dragonboard410c.dts
 create mode 100644 arch/arm/mach-snapdragon/Kconfig
 create mode 100644 arch/arm/mach-snapdragon/Makefile
 create mode 100644 arch/arm/mach-snapdragon/clock-apq8016.c
 create mode 100644 arch/arm/mach-snapdragon/include/mach/gpio.h
 create mode 100644 arch/arm/mach-snapdragon/include/mach/sysmap-apq8016.h
 create mode 100644 arch/arm/mach-snapdragon/reset.c
 create mode 100644 board/qualcomm/dragonboard410c/Kconfig
 create mode 100644 board/qualcomm/dragonboard410c/MAINTAINERS
 create mode 100644 board/qualcomm/dragonboard410c/Makefile
 create mode 100644 board/qualcomm/dragonboard410c/dragonboard410c.c
 create mode 100644 board/qualcomm/dragonboard410c/head.S
 create mode 100644 board/qualcomm/dragonboard410c/readme.txt
 create mode 100644 board/qualcomm/dragonboard410c/u-boot.lds
 create mode 100644 configs/dragonboard410c_defconfig
 create mode 100644 doc/device-tree-bindings/gpio/gpio-msm.txt
 create mode 100644 doc/device-tree-bindings/gpio/pm8916_gpio.txt
 create mode 100644 doc/device-tree-bindings/mmc/msm_sdhci.txt
 create mode 100644 doc/device-tree-bindings/pmic/pm8916.txt
 create mode 100644 doc/device-tree-bindings/serial/msm-serial.txt
 create mode 100644 doc/device-tree-bindings/spmi/spmi-msm.txt
 create mode 100644 doc/device-tree-bindings/spmi/spmi-sandbox.txt
 create mode 100644 doc/device-tree-bindings/usb/ehci-msm.txt
 create mode 100644 drivers/gpio/msm_gpio.c
 create mode 100644 drivers/gpio/pm8916_gpio.c
 create mode 100644 drivers/mmc/msm_sdhci.c
 create mode 100644 drivers/power/pmic/pm8916.c
 create mode 100644 drivers/serial/serial_msm.c
 create mode 100644 drivers/spmi/Kconfig
 create mode 100644 drivers/spmi/Makefile
 create mode 100644 drivers/spmi/spmi-msm.c
 create mode 100644 drivers/spmi/spmi-sandbox.c
 create mode 100644 drivers/spmi/spmi-uclass.c
 create mode 100644 drivers/usb/host/ehci-msm.c
 create mode 100644 drivers/usb/ulpi/Kconfig
 create mode 100644 include/configs/dragonboard410c.h
 create mode 100644 include/spmi/spmi.h
 rename include/usb/{ehci-fsl.h => ehci-ci.h} (96%)
 create mode 100644 test/dm/spmi.c

-- 
2.5.0

[U-Boot] [PATCH v3 01/21] serial: Add support for Qualcomm serial port

[Mateusz Kulikowski]

This driver works in "new" Data Mover UART mode, so
will be compatible with modern Qualcomm chips only.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3:
- Add msm_serial_fetch that tries to fetch characters from FIFO
- Decrease no of characters requested in RX transaction
- Try to fetch characters from FIFO when tstc()/pending() is called

Changes in v2:
- Added newline before return... (globally)
- Renamed p to priv (priv data) - it required some rewrapping
- Added Reviewed-by

Changes in v1:
- Added (better) help to KConfig
- Added dt binding documentation
- Fixed include ordering
- Reworked msm_serial_getc
- Added error handling to msm_uart_clk_init (that is ignored later for now)
- Dropped unneeded DM_FLAG_PRE_RELOC

 doc/device-tree-bindings/serial/msm-serial.txt |   6 +
 drivers/serial/Kconfig                         |   8 +
 drivers/serial/Makefile                        |   1 +
 drivers/serial/serial_msm.c                    | 217 +++++++++++++++++++++++++
 4 files changed, 232 insertions(+)
 create mode 100644 doc/device-tree-bindings/serial/msm-serial.txt
 create mode 100644 drivers/serial/serial_msm.c

diff --git a/doc/device-tree-bindings/serial/msm-serial.txt b/doc/device-tree-bindings/serial/msm-serial.txt
new file mode 100644
index 0000000..48b8428
--- /dev/null
+++ b/doc/device-tree-bindings/serial/msm-serial.txt
@@ -0,0 +1,6 @@
+Qualcomm UART (Data Mover mode)
+
+Required properties:
+- compatible: must be "qcom,msm-uartdm-v1.4"
+- reg: start address and size of the registers
+- clock: interface clock (must accept baudrate as a frequency)
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 92d4212..e748663 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -311,4 +311,12 @@ config XILINX_UARTLITE
 	  If you have a Xilinx based board and want to use the uartlite
 	  serial ports, say Y to this option. If unsure, say N.
 
+config MSM_SERIAL
+	bool "Qualcomm on-chip UART"
+	depends on DM_SERIAL
+	help
+	  Support Data Mover UART used on Qualcomm Snapdragon SoCs.
+	  It should support all Qualcomm devices with UARTDM version 1.4,
+	  for example APQ8016 and MSM8916.
+	  Single baudrate is supported in current implementation (115200).
 endmenu
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 05bdf56..462dba1 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -38,6 +38,7 @@ obj-$(CONFIG_UNIPHIER_SERIAL) += serial_uniphier.o
 obj-$(CONFIG_STM32_SERIAL) += serial_stm32.o
 obj-$(CONFIG_PIC32_SERIAL) += serial_pic32.o
 obj-$(CONFIG_STM32X7_SERIAL) += serial_stm32x7.o
+obj-$(CONFIG_MSM_SERIAL) += serial_msm.o
 
 ifndef CONFIG_SPL_BUILD
 obj-$(CONFIG_USB_TTY) += usbtty.o
diff --git a/drivers/serial/serial_msm.c b/drivers/serial/serial_msm.c
new file mode 100644
index 0000000..80fb89e
--- /dev/null
+++ b/drivers/serial/serial_msm.c
@@ -0,0 +1,217 @@
+/*
+ * Qualcomm UART driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * UART will work in Data Mover mode.
+ * Based on Linux driver.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <errno.h>
+#include <serial.h>
+#include <watchdog.h>
+#include <asm/io.h>
+#include <linux/compiler.h>
+
+/* Serial registers - this driver works in uartdm mode*/
+
+#define UARTDM_DMRX             0x34 /* Max RX transfer length */
+#define UARTDM_NCF_TX           0x40 /* Number of chars to TX */
+
+#define UARTDM_RXFS             0x50 /* RX channel status register */
+#define UARTDM_RXFS_BUF_SHIFT   0x7  /* Number of bytes in the packing buffer */
+#define UARTDM_RXFS_BUF_MASK    0x7
+
+#define UARTDM_SR                0xA4 /* Status register */
+#define UARTDM_SR_RX_READY       (1 << 0) /* Word is the receiver FIFO */
+#define UARTDM_SR_TX_EMPTY       (1 << 3) /* Transmitter underrun */
+#define UARTDM_SR_UART_OVERRUN   (1 << 4) /* Receive overrun */
+
+#define UARTDM_CR                         0xA8 /* Command register */
+#define UARTDM_CR_CMD_RESET_ERR           (3 << 4) /* Clear overrun error */
+#define UARTDM_CR_CMD_RESET_STALE_INT     (8 << 4) /* Clears stale irq */
+#define UARTDM_CR_CMD_RESET_TX_READY      (3 << 8) /* Clears TX Ready irq*/
+#define UARTDM_CR_CMD_FORCE_STALE         (4 << 8) /* Causes stale event */
+#define UARTDM_CR_CMD_STALE_EVENT_DISABLE (6 << 8) /* Disable stale event */
+
+#define UARTDM_IMR                0xB0 /* Interrupt mask register */
+#define UARTDM_ISR                0xB4 /* Interrupt status register */
+#define UARTDM_ISR_TX_READY       0x80 /* TX FIFO empty */
+
+#define UARTDM_TF               0x100 /* UART Transmit FIFO register */
+#define UARTDM_RF               0x140 /* UART Receive FIFO register */
+
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct msm_serial_data {
+	phys_addr_t base;
+	unsigned chars_cnt; /* number of buffered chars */
+	uint32_t chars_buf; /* buffered chars */
+};
+
+static int msm_serial_fetch(struct udevice *dev)
+{
+	struct msm_serial_data *priv = dev_get_priv(dev);
+	unsigned sr;
+
+	if (priv->chars_cnt)
+		return priv->chars_cnt;
+
+	/* Clear error in case of buffer overrun */
+	if (readl(priv->base + UARTDM_SR) & UARTDM_SR_UART_OVERRUN)
+		writel(UARTDM_CR_CMD_RESET_ERR, priv->base + UARTDM_CR);
+
+	/* We need to fetch new character */
+	sr = readl(priv->base + UARTDM_SR);
+
+	if (sr & UARTDM_SR_RX_READY) {
+		/* There are at least 4 bytes in fifo */
+		priv->chars_buf = readl(priv->base + UARTDM_RF);
+		priv->chars_cnt = 4;
+	} else {
+		/* Check if there is anything in fifo */
+		priv->chars_cnt = readl(priv->base + UARTDM_RXFS);
+		/* Extract number of characters in UART packing buffer*/
+		priv->chars_cnt = (priv->chars_cnt >>
+				   UARTDM_RXFS_BUF_SHIFT) &
+				  UARTDM_RXFS_BUF_MASK;
+		if (!priv->chars_cnt)
+			return 0;
+
+		/* There is at least one charcter, move it to fifo */
+		writel(UARTDM_CR_CMD_FORCE_STALE,
+		       priv->base + UARTDM_CR);
+
+		priv->chars_buf = readl(priv->base + UARTDM_RF);
+		writel(UARTDM_CR_CMD_RESET_STALE_INT,
+		       priv->base + UARTDM_CR);
+		writel(0x7, priv->base + UARTDM_DMRX);
+	}
+
+	return priv->chars_cnt;
+}
+
+static int msm_serial_getc(struct udevice *dev)
+{
+	struct msm_serial_data *priv = dev_get_priv(dev);
+	char c;
+
+	if (!msm_serial_fetch(dev))
+		return -EAGAIN;
+
+	c = priv->chars_buf & 0xFF;
+	priv->chars_buf >>= 8;
+	priv->chars_cnt--;
+
+	return c;
+}
+
+static int msm_serial_putc(struct udevice *dev, const char ch)
+{
+	struct msm_serial_data *priv = dev_get_priv(dev);
+
+	if (!(readl(priv->base + UARTDM_SR) & UARTDM_SR_TX_EMPTY) &&
+	    !(readl(priv->base + UARTDM_ISR) & UARTDM_ISR_TX_READY))
+		return -EAGAIN;
+
+	writel(UARTDM_CR_CMD_RESET_TX_READY, priv->base + UARTDM_CR);
+
+	writel(1, priv->base + UARTDM_NCF_TX);
+	writel(ch, priv->base + UARTDM_TF);
+
+	return 0;
+}
+
+static int msm_serial_pending(struct udevice *dev, bool input)
+{
+	if (input) {
+		if (msm_serial_fetch(dev))
+			return 1;
+	}
+
+	return 0;
+}
+
+static const struct dm_serial_ops msm_serial_ops = {
+	.putc = msm_serial_putc,
+	.pending = msm_serial_pending,
+	.getc = msm_serial_getc,
+};
+
+static int msm_uart_clk_init(struct udevice *dev)
+{
+	uint clk_rate = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+					"clock-frequency", 115200);
+	uint clkd[2]; /* clk_id and clk_no */
+	int clk_offset;
+	struct udevice *clk;
+	int ret;
+
+	ret = fdtdec_get_int_array(gd->fdt_blob, dev->of_offset, "clock", clkd,
+				   2);
+	if (ret)
+		return ret;
+
+	clk_offset = fdt_node_offset_by_phandle(gd->fdt_blob, clkd[0]);
+	if (clk_offset < 0)
+		return clk_offset;
+
+	ret = uclass_get_device_by_of_offset(UCLASS_CLK, clk_offset, &clk);
+	if (ret)
+		return ret;
+
+	ret = clk_set_periph_rate(clk, clkd[1], clk_rate);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int msm_serial_probe(struct udevice *dev)
+{
+	struct msm_serial_data *priv = dev_get_priv(dev);
+
+	msm_uart_clk_init(dev); /* Ignore return value and hope clock was
+				  properly initialized by earlier loaders */
+
+	if (readl(priv->base + UARTDM_SR) & UARTDM_SR_UART_OVERRUN)
+		writel(UARTDM_CR_CMD_RESET_ERR, priv->base + UARTDM_CR);
+
+	writel(0, priv->base + UARTDM_IMR);
+	writel(UARTDM_CR_CMD_STALE_EVENT_DISABLE, priv->base + UARTDM_CR);
+	msm_serial_fetch(dev);
+
+	return 0;
+}
+
+static int msm_serial_ofdata_to_platdata(struct udevice *dev)
+{
+	struct msm_serial_data *priv = dev_get_priv(dev);
+
+	priv->base = dev_get_addr(dev);
+	if (priv->base == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct udevice_id msm_serial_ids[] = {
+	{ .compatible = "qcom,msm-uartdm-v1.4" },
+	{ }
+};
+
+U_BOOT_DRIVER(serial_msm) = {
+	.name	= "serial_msm",
+	.id	= UCLASS_SERIAL,
+	.of_match = msm_serial_ids,
+	.ofdata_to_platdata = msm_serial_ofdata_to_platdata,
+	.priv_auto_alloc_size = sizeof(struct msm_serial_data),
+	.probe = msm_serial_probe,
+	.ops	= &msm_serial_ops,
+};
-- 
2.5.0

[U-Boot] [PATCH v3 02/21] gpio: Add support for Qualcomm gpio controller

[Mateusz Kulikowski]

Add support for gpio controllers on Qualcomm Snapdragon devices.
This devices are usually called Top Level Mode Multiplexing in
Qualcomm documentation.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Reordered includes (again)
- Added newlines between returns
- Fixed error handling in msm_gpio_probe
- Added reviewed-by

Changes in v1:
- Added dt binding documentation
- Added help to KConfig
- Use clrsetbits() to switch direction
- Fixed include order
- Added #defines for registers/register fields
- Added secondary compatible string

 doc/device-tree-bindings/gpio/gpio-msm.txt |  22 +++++
 drivers/gpio/Kconfig                       |  14 +++
 drivers/gpio/Makefile                      |   1 +
 drivers/gpio/msm_gpio.c                    | 135 +++++++++++++++++++++++++++++
 4 files changed, 172 insertions(+)
 create mode 100644 doc/device-tree-bindings/gpio/gpio-msm.txt
 create mode 100644 drivers/gpio/msm_gpio.c

diff --git a/doc/device-tree-bindings/gpio/gpio-msm.txt b/doc/device-tree-bindings/gpio/gpio-msm.txt
new file mode 100644
index 0000000..966ce0a
--- /dev/null
+++ b/doc/device-tree-bindings/gpio/gpio-msm.txt
@@ -0,0 +1,22 @@
+Qualcomm Snapdragon GPIO controller
+
+Required properties:
+- compatible : "qcom,msm8916-pinctrl" or "qcom,apq8016-pinctrl"
+- reg : Physical base address and length of the controller's registers.
+	This controller is called "Top Level Mode Multiplexing" in
+	Qualcomm documentation.
+- #gpio-cells : Should be one (pin number).
+- gpio-controller : Marks the device node as a GPIO controller.
+- gpio-count: Number of GPIO pins.
+- gpio-bank-name: (optional) name of gpio bank. As default "soc" is used.
+
+Example:
+
+soc_gpios: pinctrl at 1000000 {
+	compatible = "qcom,msm8916-pinctrl";
+	reg = <0x1000000 0x300000>;
+	gpio-controller;
+	gpio-count = <122>;
+	gpio-bank-name="soc";
+	#gpio-cells = <1>;
+};
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 94fabb9..befb4af 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -46,6 +46,20 @@ config LPC32XX_GPIO
 	help
 	  Support for the LPC32XX GPIO driver.
 
+config MSM_GPIO
+	bool "Qualcomm GPIO driver"
+	depends on DM_GPIO
+	default n
+	help
+	  Support GPIO controllers on Qualcomm Snapdragon family of SoCs.
+	  This controller have single bank (default name "soc"), every
+	  gpio has it's own set of registers.
+	  Only simple GPIO operations are supported (get/set, change of
+	  direction and checking pin function).
+	  Supported devices:
+	  - APQ8016
+	  - MSM8916
+
 config ROCKCHIP_GPIO
 	bool "Rockchip GPIO driver"
 	depends on DM_GPIO
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index ca8c487..830d7a6 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -48,3 +48,4 @@ obj-$(CONFIG_ZYNQ_GPIO)		+= zynq_gpio.o
 obj-$(CONFIG_VYBRID_GPIO)	+= vybrid_gpio.o
 obj-$(CONFIG_HIKEY_GPIO)	+= hi6220_gpio.o
 obj-$(CONFIG_PIC32_GPIO)	+= pic32_gpio.o
+obj-$(CONFIG_MSM_GPIO)		+= msm_gpio.o
diff --git a/drivers/gpio/msm_gpio.c b/drivers/gpio/msm_gpio.c
new file mode 100644
index 0000000..950f309
--- /dev/null
+++ b/drivers/gpio/msm_gpio.c
@@ -0,0 +1,135 @@
+/*
+ * Qualcomm GPIO driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Register offsets */
+#define GPIO_CONFIG_OFF(no)         ((no) * 0x1000)
+#define GPIO_IN_OUT_OFF(no)         ((no) * 0x1000 + 0x4)
+
+/* OE */
+#define GPIO_OE_DISABLE  (0x0 << 9)
+#define GPIO_OE_ENABLE   (0x1 << 9)
+#define GPIO_OE_MASK     (0x1 << 9)
+
+/* GPIO_IN_OUT register shifts. */
+#define GPIO_IN          0
+#define GPIO_OUT         1
+
+struct msm_gpio_bank {
+	phys_addr_t base;
+};
+
+static int msm_gpio_direction_input(struct udevice *dev, unsigned int gpio)
+{
+	struct msm_gpio_bank *priv = dev_get_priv(dev);
+	phys_addr_t reg = priv->base + GPIO_CONFIG_OFF(gpio);
+
+	/* Disable OE bit */
+	clrsetbits_le32(reg, GPIO_OE_MASK, GPIO_OE_DISABLE);
+
+	return 0;
+}
+
+static int msm_gpio_set_value(struct udevice *dev, unsigned gpio, int value)
+{
+	struct msm_gpio_bank *priv = dev_get_priv(dev);
+
+	value = !!value;
+	/* set value */
+	writel(value << GPIO_OUT, priv->base + GPIO_IN_OUT_OFF(gpio));
+
+	return 0;
+}
+
+static int msm_gpio_direction_output(struct udevice *dev, unsigned gpio,
+				     int value)
+{
+	struct msm_gpio_bank *priv = dev_get_priv(dev);
+	phys_addr_t reg = priv->base + GPIO_CONFIG_OFF(gpio);
+
+	value = !!value;
+	/* set value */
+	writel(value << GPIO_OUT, priv->base + GPIO_IN_OUT_OFF(gpio));
+	/* switch direction */
+	clrsetbits_le32(reg, GPIO_OE_MASK, GPIO_OE_ENABLE);
+
+	return 0;
+}
+
+static int msm_gpio_get_value(struct udevice *dev, unsigned gpio)
+{
+	struct msm_gpio_bank *priv = dev_get_priv(dev);
+
+	return !!(readl(priv->base + GPIO_IN_OUT_OFF(gpio)) >> GPIO_IN);
+}
+
+static int msm_gpio_get_function(struct udevice *dev, unsigned offset)
+{
+	struct msm_gpio_bank *priv = dev_get_priv(dev);
+
+	if (readl(priv->base + GPIO_CONFIG_OFF(offset)) & GPIO_OE_ENABLE)
+		return GPIOF_OUTPUT;
+
+	return GPIOF_INPUT;
+}
+
+static const struct dm_gpio_ops gpio_msm_ops = {
+	.direction_input	= msm_gpio_direction_input,
+	.direction_output	= msm_gpio_direction_output,
+	.get_value		= msm_gpio_get_value,
+	.set_value		= msm_gpio_set_value,
+	.get_function		= msm_gpio_get_function,
+};
+
+static int msm_gpio_probe(struct udevice *dev)
+{
+	struct msm_gpio_bank *priv = dev_get_priv(dev);
+
+	priv->base = dev_get_addr(dev);
+
+	return priv->base == FDT_ADDR_T_NONE ? -EINVAL : 0;
+}
+
+static int msm_gpio_ofdata_to_platdata(struct udevice *dev)
+{
+	struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+
+	uc_priv->gpio_count = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
+					     "gpio-count", 0);
+	uc_priv->bank_name = fdt_getprop(gd->fdt_blob, dev->of_offset,
+					 "gpio-bank-name", NULL);
+	if (uc_priv->bank_name == NULL)
+		uc_priv->bank_name = "soc";
+
+	return 0;
+}
+
+static const struct udevice_id msm_gpio_ids[] = {
+	{ .compatible = "qcom,msm8916-pinctrl" },
+	{ .compatible = "qcom,apq8016-pinctrl" },
+	{ }
+};
+
+U_BOOT_DRIVER(gpio_msm) = {
+	.name	= "gpio_msm",
+	.id	= UCLASS_GPIO,
+	.of_match = msm_gpio_ids,
+	.ofdata_to_platdata = msm_gpio_ofdata_to_platdata,
+	.probe	= msm_gpio_probe,
+	.ops	= &gpio_msm_ops,
+	.priv_auto_alloc_size = sizeof(struct msm_gpio_bank),
+};
+
+
-- 
2.5.0

[U-Boot] [PATCH v3 03/21] mmc: Add support for Qualcomm SDHCI controller

[Mateusz Kulikowski]

Add support for SD/eMMC controller present on some Qualcomm Snapdragon
devices. This controller implements SDHCI 2.0 interface but requires
vendor-specific initialization.
Driver works in PIO mode as ADMA is not supported by U-Boot (yet).

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Add reviewed-by

Changes in v1:
- Added commit message
- Added DT binding documentation
- Added Kconfig help
- Reordered includes
- Dropped redundant fields from msm_sdhc
- Cleaned up clock init code (+ added error handling)
- Dropped mdelay - use wait_for_bit instead in reset code
- Added missing newline after declarations
- Added error handling if "reg" is missing
- Converted base address to pointer

 doc/device-tree-bindings/mmc/msm_sdhci.txt |  25 ++++
 drivers/mmc/Kconfig                        |   9 ++
 drivers/mmc/Makefile                       |   1 +
 drivers/mmc/msm_sdhci.c                    | 180 +++++++++++++++++++++++++++++
 4 files changed, 215 insertions(+)
 create mode 100644 doc/device-tree-bindings/mmc/msm_sdhci.txt
 create mode 100644 drivers/mmc/msm_sdhci.c

diff --git a/doc/device-tree-bindings/mmc/msm_sdhci.txt b/doc/device-tree-bindings/mmc/msm_sdhci.txt
new file mode 100644
index 0000000..08a290c
--- /dev/null
+++ b/doc/device-tree-bindings/mmc/msm_sdhci.txt
@@ -0,0 +1,25 @@
+Qualcomm Snapdragon SDHCI controller
+
+Required properties:
+- compatible : "qcom,sdhci-msm-v4"
+- reg: Base address and length of registers:
+	- Host controller registers (SDHCI)
+	- SD Core registers
+- clock: interface clock (must accept SD bus clock as a frequency)
+
+Optional properties:
+- index: If there is more than one controller - controller index (required
+	by generic SDHCI code).
+- bus_width: Width of SD/eMMC bus (default 4)
+- clock-frequency: Frequency of SD/eMMC bus (default 400 kHz)
+
+Example:
+
+sdhci at 07864000 {
+	compatible = "qcom,sdhci-msm-v4";
+	reg = <0x7864900 0x11c 0x7864000 0x800>;
+	index = <0x1>;
+	bus-width = <0x4>;
+	clock = <&clkc 1>;
+	clock-frequency = <200000000>;
+};
diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index dc8532f..4d3df11 100644
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -16,6 +16,15 @@ config DM_MMC
 	  appear as block devices in U-Boot and can support filesystems such
 	  as EXT4 and FAT.
 
+config MSM_SDHCI
+	bool "Qualcomm SDHCI controller"
+	depends on DM_MMC
+	help
+	  Enables support for SDHCI 2.0 controller present on some Qualcomm
+          Snapdragon devices. This device is compatible with eMMC v4.5 and
+          SD 3.0 specifications. Both SD and eMMC devices are supported.
+	  Card-detect gpios are not supported.
+
 config ROCKCHIP_DWMMC
 	bool "Rockchip SD/MMC controller support"
 	depends on DM_MMC && OF_CONTROL
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index b85e4bf..585aaf3 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -50,3 +50,4 @@ else
 obj-$(CONFIG_GENERIC_MMC) += mmc_write.o
 endif
 obj-$(CONFIG_PIC32_SDHCI) += pic32_sdhci.o
+obj-$(CONFIG_MSM_SDHCI) += msm_sdhci.o
diff --git a/drivers/mmc/msm_sdhci.c b/drivers/mmc/msm_sdhci.c
new file mode 100644
index 0000000..1e2a29b
--- /dev/null
+++ b/drivers/mmc/msm_sdhci.c
@@ -0,0 +1,180 @@
+/*
+ * Qualcomm SDHCI driver - SD/eMMC controller
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * Based on Linux driver
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <sdhci.h>
+#include <wait_bit.h>
+#include <asm/io.h>
+#include <linux/bitops.h>
+
+/* Non-standard registers needed for SDHCI startup */
+#define SDCC_MCI_POWER   0x0
+#define SDCC_MCI_POWER_SW_RST BIT(7)
+
+/* This is undocumented register */
+#define SDCC_MCI_VERSION             0x50
+#define SDCC_MCI_VERSION_MAJOR_SHIFT 28
+#define SDCC_MCI_VERSION_MAJOR_MASK  (0xf << SDCC_MCI_VERSION_MAJOR_SHIFT)
+#define SDCC_MCI_VERSION_MINOR_MASK  0xff
+
+#define SDCC_MCI_STATUS2 0x6C
+#define SDCC_MCI_STATUS2_MCI_ACT 0x1
+#define SDCC_MCI_HC_MODE 0x78
+
+/* Offset to SDHCI registers */
+#define SDCC_SDHCI_OFFSET 0x900
+
+/* Non standard (?) SDHCI register */
+#define SDHCI_VENDOR_SPEC_CAPABILITIES0  0x11c
+
+struct msm_sdhc {
+	struct sdhci_host host;
+	void *base;
+};
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int msm_sdc_clk_init(struct udevice *dev)
+{
+	uint clk_rate = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+					"clock-frequency", 400000);
+	uint clkd[2]; /* clk_id and clk_no */
+	int clk_offset;
+	struct udevice *clk;
+	int ret;
+
+	ret = fdtdec_get_int_array(gd->fdt_blob, dev->of_offset, "clock", clkd,
+				   2);
+	if (ret)
+		return ret;
+
+	clk_offset = fdt_node_offset_by_phandle(gd->fdt_blob, clkd[0]);
+	if (clk_offset < 0)
+		return clk_offset;
+
+	ret = uclass_get_device_by_of_offset(UCLASS_CLK, clk_offset, &clk);
+	if (ret)
+		return ret;
+
+	ret = clk_set_periph_rate(clk, clkd[1], clk_rate);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int msm_sdc_probe(struct udevice *dev)
+{
+	struct msm_sdhc *prv = dev_get_priv(dev);
+	struct sdhci_host *host = &prv->host;
+	u32 core_version, core_minor, core_major;
+	int ret;
+
+	host->quirks = SDHCI_QUIRK_WAIT_SEND_CMD | SDHCI_QUIRK_BROKEN_R1B;
+
+	/* Init clocks */
+	ret = msm_sdc_clk_init(dev);
+	if (ret)
+		return ret;
+
+	/* Reset the core and Enable SDHC mode */
+	writel(readl(prv->base + SDCC_MCI_POWER) | SDCC_MCI_POWER_SW_RST,
+	       prv->base + SDCC_MCI_POWER);
+
+
+	/* Wait for reset to be written to register */
+	if (wait_for_bit(__func__, prv->base + SDCC_MCI_STATUS2,
+			 SDCC_MCI_STATUS2_MCI_ACT, false, 10, false)) {
+		printf("msm_sdhci: reset request failed\n");
+		return -EIO;
+	}
+
+	/* SW reset can take upto 10HCLK + 15MCLK cycles. (min 40us) */
+	if (wait_for_bit(__func__, prv->base + SDCC_MCI_POWER,
+			 SDCC_MCI_POWER_SW_RST, false, 2, false)) {
+		printf("msm_sdhci: stuck in reset\n");
+		return -ETIMEDOUT;
+	}
+
+	/* Enable host-controller mode */
+	writel(1, prv->base + SDCC_MCI_HC_MODE);
+
+	core_version = readl(prv->base + SDCC_MCI_VERSION);
+
+	core_major = (core_version & SDCC_MCI_VERSION_MAJOR_MASK);
+	core_major >>= SDCC_MCI_VERSION_MAJOR_SHIFT;
+
+	core_minor = core_version & SDCC_MCI_VERSION_MINOR_MASK;
+
+	/*
+	 * Support for some capabilities is not advertised by newer
+	 * controller versions and must be explicitly enabled.
+	 */
+	if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) {
+		u32 caps = readl(host->ioaddr + SDHCI_CAPABILITIES);
+		caps |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
+		writel(caps, host->ioaddr + SDHCI_VENDOR_SPEC_CAPABILITIES0);
+	}
+
+	/* Set host controller version */
+	host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
+
+	/* automatically detect max and min speed */
+	return add_sdhci(host, 0, 0);
+}
+
+static int msm_sdc_remove(struct udevice *dev)
+{
+	struct msm_sdhc *priv = dev_get_priv(dev);
+
+	 /* Disable host-controller mode */
+	writel(0, priv->base + SDCC_MCI_HC_MODE);
+
+	return 0;
+}
+
+static int msm_ofdata_to_platdata(struct udevice *dev)
+{
+	struct udevice *parent = dev->parent;
+	struct msm_sdhc *priv = dev_get_priv(dev);
+	struct sdhci_host *host = &priv->host;
+
+	host->name = strdup(dev->name);
+	host->ioaddr = (void *)dev_get_addr(dev);
+	host->bus_width = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
+					 "bus-width", 4);
+	host->index = fdtdec_get_uint(gd->fdt_blob, dev->of_offset, "index", 0);
+	priv->base = (void *)fdtdec_get_addr_size_auto_parent(gd->fdt_blob,
+							      parent->of_offset,
+							      dev->of_offset,
+							      "reg", 1, NULL);
+	if (priv->base == (void *)FDT_ADDR_T_NONE ||
+	    host->ioaddr == (void *)FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct udevice_id msm_mmc_ids[] = {
+	{ .compatible = "qcom,sdhci-msm-v4" },
+	{ }
+};
+
+U_BOOT_DRIVER(msm_sdc_drv) = {
+	.name		= "msm_sdc",
+	.id		= UCLASS_MMC,
+	.of_match	= msm_mmc_ids,
+	.ofdata_to_platdata = msm_ofdata_to_platdata,
+	.probe		= msm_sdc_probe,
+	.remove		= msm_sdc_remove,
+	.priv_auto_alloc_size = sizeof(struct msm_sdhc),
+};
-- 
2.5.0

[U-Boot] [PATCH v3 04/21] ehci-hcd: Add init_after_reset

[Mateusz Kulikowski]

Some host controllers need addidional initialization after ehci_reset()
In non-dm implementation it is possible to use CONFIG_EHCI_HCD_INIT_AFTER_RESET.
This patch adds similar option to ehci drivers using dm.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Add Reviewed-by (sjg)

Changes in v1:
- No changes, just added Acked-by, Reviewed-by

 drivers/usb/host/ehci-hcd.c | 6 ++++++
 drivers/usb/host/ehci.h     | 1 +
 2 files changed, 7 insertions(+)

diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index 0113c6c..598f444 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -1615,6 +1615,12 @@ int ehci_register(struct udevice *dev, struct ehci_hccr *hccr,
 	if (ret)
 		goto err;
 
+	if (ops->init_after_reset) {
+		ret = ops->init_after_reset(ctrl);
+		if (ret)
+			goto err;
+	}
+
 	ret = ehci_common_init(ctrl, tweaks);
 	if (ret)
 		goto err;
diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h
index 826b3fe..734d7f0 100644
--- a/drivers/usb/host/ehci.h
+++ b/drivers/usb/host/ehci.h
@@ -240,6 +240,7 @@ struct ehci_ops {
 	void (*powerup_fixup)(struct ehci_ctrl *ctrl, uint32_t *status_reg,
 			      uint32_t *reg);
 	uint32_t *(*get_portsc_register)(struct ehci_ctrl *ctrl, int port);
+	int (*init_after_reset)(struct ehci_ctrl *ctrl);
 };
 
 struct ehci_ctrl {
-- 
2.5.0

[U-Boot] [PATCH v3 05/21] usb: ulpi: Add Kconfig options for ULPI

[Mateusz Kulikowski]

The following options can be now enabled via defconfig:
- CONFIG_USB_ULPI
- CONFIG_USB_ULPI_VIEWPORT
- CONFIG_USB_ULPI_VIEWPORT_OMAP

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Add better (any) descriptions for Kconfig items.

Changes in v1: None

 drivers/usb/Kconfig      |  2 ++
 drivers/usb/ulpi/Kconfig | 33 +++++++++++++++++++++++++++++++++
 2 files changed, 35 insertions(+)
 create mode 100644 drivers/usb/ulpi/Kconfig

diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index abb06fc..57b99f2 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -53,6 +53,8 @@ source "drivers/usb/musb-new/Kconfig"
 
 source "drivers/usb/emul/Kconfig"
 
+source "drivers/usb/ulpi/Kconfig"
+
 comment "USB peripherals"
 
 config USB_STORAGE
diff --git a/drivers/usb/ulpi/Kconfig b/drivers/usb/ulpi/Kconfig
new file mode 100644
index 0000000..329d2df
--- /dev/null
+++ b/drivers/usb/ulpi/Kconfig
@@ -0,0 +1,33 @@
+comment "ULPI drivers"
+
+choice
+	prompt "ULPI Viewport type"
+	optional
+	default n
+	help
+	  Select ULPI viewport (SoC-side interface to ULPI) implementation
+	  appropriate for the device if you want to communicate with
+	  UTMI (USB PHY) via ULPI interface.
+
+config USB_ULPI_VIEWPORT
+	bool "Generic ULPI Viewport"
+	help
+	  Support generic ULPI Viewport implementation that is used on
+	  some Tegra and Snapdragon devices.
+
+config USB_ULPI_VIEWPORT_OMAP
+	bool "OMAP ULPI Viewport"
+	help
+	  Support ULPI Viewport implementation that is used on OMAP devices.
+
+endchoice
+
+config USB_ULPI
+	bool "ULPI support"
+	depends on (USB_ULPI_VIEWPORT || USB_ULPI_VIEWPORT_OMAP)
+	help
+	  Select to commnicate with USB PHY via ULPI interface.
+	  ULPI is wrapper on UTMI+ core that is used as
+	  PHY Transreceiver for USB controllers.
+
+	  This driver uses ULPI viewports that are specific for each SoC.
-- 
2.5.0

[U-Boot] [PATCH v3 06/21] Migrate CONFIG_ULPI* to Kconfig

[Mateusz Kulikowski]

Move CONFIG_USB_ULPI* from headers to defconfigs for boards that use it.
Also - add CONFIG_USB where necesarry - all boards use it,
but some are not defining it explicitly.

Affected boards:
colibri_t20, harmony, mcx, mt_ventoux, twister,
zynq_(picozed, zc702, zc706, zed, zybo)

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- New patch, independent of the rest
- Should compile cleanly on all affected platforms
- Is orthogonal to series (i.e. if get's NAK will not break rest of series)

Changes in v1: None

 configs/colibri_t20_defconfig    | 2 ++
 configs/harmony_defconfig        | 2 ++
 configs/mcx_defconfig            | 3 +++
 configs/mt_ventoux_defconfig     | 3 +++
 configs/twister_defconfig        | 3 +++
 configs/zynq_picozed_defconfig   | 3 +++
 configs/zynq_zc702_defconfig     | 3 +++
 configs/zynq_zc706_defconfig     | 3 +++
 configs/zynq_zed_defconfig       | 3 +++
 configs/zynq_zybo_defconfig      | 3 +++
 include/configs/colibri_t20.h    | 3 +--
 include/configs/harmony.h        | 2 --
 include/configs/mcx.h            | 2 --
 include/configs/tam3517-common.h | 2 --
 include/configs/zynq-common.h    | 2 --
 15 files changed, 29 insertions(+), 10 deletions(-)

diff --git a/configs/colibri_t20_defconfig b/configs/colibri_t20_defconfig
index e8b3e0c..c964387 100644
--- a/configs/colibri_t20_defconfig
+++ b/configs/colibri_t20_defconfig
@@ -20,4 +20,6 @@ CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_DM_VIDEO=y
 CONFIG_VIDEO_TEGRA20=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT=y
 CONFIG_USE_PRIVATE_LIBGCC=y
diff --git a/configs/harmony_defconfig b/configs/harmony_defconfig
index 14125b4..0b2422e 100644
--- a/configs/harmony_defconfig
+++ b/configs/harmony_defconfig
@@ -21,4 +21,6 @@ CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_DM_VIDEO=y
 CONFIG_VIDEO_TEGRA20=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT=y
 CONFIG_USE_PRIVATE_LIBGCC=y
diff --git a/configs/mcx_defconfig b/configs/mcx_defconfig
index 1e204d5..612bf66 100644
--- a/configs/mcx_defconfig
+++ b/configs/mcx_defconfig
@@ -10,3 +10,6 @@ CONFIG_SYS_PROMPT="mcx # "
 CONFIG_CMD_GPIO=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT_OMAP=y
diff --git a/configs/mt_ventoux_defconfig b/configs/mt_ventoux_defconfig
index a0153e4..8b3298b 100644
--- a/configs/mt_ventoux_defconfig
+++ b/configs/mt_ventoux_defconfig
@@ -8,3 +8,6 @@ CONFIG_SYS_PROMPT="mt_ventoux => "
 CONFIG_CMD_GPIO=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT_OMAP=y
diff --git a/configs/twister_defconfig b/configs/twister_defconfig
index e721edb..a1abbe1 100644
--- a/configs/twister_defconfig
+++ b/configs/twister_defconfig
@@ -8,3 +8,6 @@ CONFIG_SYS_PROMPT="twister => "
 CONFIG_CMD_GPIO=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_SYS_NS16550=y
+CONFIG_USB=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT_OMAP=y
diff --git a/configs/zynq_picozed_defconfig b/configs/zynq_picozed_defconfig
index f34e2e3..540b0dd 100644
--- a/configs/zynq_picozed_defconfig
+++ b/configs/zynq_picozed_defconfig
@@ -12,3 +12,6 @@ CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_SPL_DM_SEQ_ALIAS=y
 CONFIG_ZYNQ_SDHCI=y
 CONFIG_ZYNQ_GEM=y
+CONFIG_USB=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT=y
diff --git a/configs/zynq_zc702_defconfig b/configs/zynq_zc702_defconfig
index f01874f..a6db9ff 100644
--- a/configs/zynq_zc702_defconfig
+++ b/configs/zynq_zc702_defconfig
@@ -24,3 +24,6 @@ CONFIG_DEBUG_UART_ZYNQ=y
 CONFIG_DEBUG_UART_BASE=0xe0001000
 CONFIG_DEBUG_UART_CLOCK=50000000
 CONFIG_ZYNQ_QSPI=y
+CONFIG_USB=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT=y
diff --git a/configs/zynq_zc706_defconfig b/configs/zynq_zc706_defconfig
index 215f00d..d9a9bff 100644
--- a/configs/zynq_zc706_defconfig
+++ b/configs/zynq_zc706_defconfig
@@ -21,3 +21,6 @@ CONFIG_SPI_FLASH_STMICRO=y
 CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_ZYNQ_GEM=y
 CONFIG_ZYNQ_QSPI=y
+CONFIG_USB=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT=y
diff --git a/configs/zynq_zed_defconfig b/configs/zynq_zed_defconfig
index 4a2a2fc..25df8e5 100644
--- a/configs/zynq_zed_defconfig
+++ b/configs/zynq_zed_defconfig
@@ -21,3 +21,6 @@ CONFIG_SPI_FLASH_STMICRO=y
 CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_ZYNQ_GEM=y
 CONFIG_ZYNQ_QSPI=y
+CONFIG_USB=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT=y
diff --git a/configs/zynq_zybo_defconfig b/configs/zynq_zybo_defconfig
index 7c23fec..dd8cb62 100644
--- a/configs/zynq_zybo_defconfig
+++ b/configs/zynq_zybo_defconfig
@@ -22,3 +22,6 @@ CONFIG_DEBUG_UART_ZYNQ=y
 CONFIG_DEBUG_UART_BASE=0xe0001000
 CONFIG_DEBUG_UART_CLOCK=50000000
 CONFIG_ZYNQ_QSPI=y
+CONFIG_USB=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT=y
diff --git a/include/configs/colibri_t20.h b/include/configs/colibri_t20.h
index b7ad189..e97e5a1 100644
--- a/include/configs/colibri_t20.h
+++ b/include/configs/colibri_t20.h
@@ -36,8 +36,7 @@
 /* USB host support */
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_TEGRA
-#define CONFIG_USB_ULPI
-#define CONFIG_USB_ULPI_VIEWPORT
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	3
 #define CONFIG_USB_STORAGE
 #define CONFIG_CMD_USB
 
diff --git a/include/configs/harmony.h b/include/configs/harmony.h
index f66ac70..0a3cb18 100644
--- a/include/configs/harmony.h
+++ b/include/configs/harmony.h
@@ -44,8 +44,6 @@
 /* USB Host support */
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_TEGRA
-#define CONFIG_USB_ULPI
-#define CONFIG_USB_ULPI_VIEWPORT
 #define CONFIG_USB_STORAGE
 #define CONFIG_CMD_USB
 
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
index 4eea06d..7987b2c 100644
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@@ -105,8 +105,6 @@
 #define CONFIG_OMAP3_GPIO_5
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_OMAP
-#define CONFIG_USB_ULPI
-#define CONFIG_USB_ULPI_VIEWPORT_OMAP
 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	57
 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
 #define	CONFIG_USB_HOST_ETHER
diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index 2d941ca..0a4d3fa 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -91,8 +91,6 @@
 #define CONFIG_OMAP3_GPIO_5
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_OMAP
-#define CONFIG_USB_ULPI
-#define CONFIG_USB_ULPI_VIEWPORT_OMAP
 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	25
 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
 #define CONFIG_USB_STORAGE
diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index 982905d..9134bfb 100644
--- a/include/configs/zynq-common.h
+++ b/include/configs/zynq-common.h
@@ -96,8 +96,6 @@
 # define CONFIG_CMD_USB
 # define CONFIG_USB_STORAGE
 # define CONFIG_USB_EHCI_ZYNQ
-# define CONFIG_USB_ULPI_VIEWPORT
-# define CONFIG_USB_ULPI
 # define CONFIG_EHCI_IS_TDI
 # define CONFIG_USB_MAX_CONTROLLER_COUNT	2
 
-- 
2.5.0

[U-Boot] [PATCH v3 07/21] usb: ulpi: Fix viewport_addr type

[Mateusz Kulikowski]

viewport_addr is address of memory mapped ULPI viewport.
It is used only as argument to readl/writel later
causing compile warnings on 64-bit devices.

This fix changes its type to match pointer size.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
---

Changes in v3:
- New patch

Changes in v2: None
Changes in v1: None

 include/usb/ulpi.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/usb/ulpi.h b/include/usb/ulpi.h
index 4fa765b..dfea395 100644
--- a/include/usb/ulpi.h
+++ b/include/usb/ulpi.h
@@ -32,7 +32,7 @@
  * be extended from this structure
  */
 struct ulpi_viewport {
-	u32 viewport_addr;
+	uintptr_t viewport_addr;
 	u32 port_num;
 };
 
-- 
2.5.0

[U-Boot] [PATCH v3 08/21] usb: ulpi: Fix compile warning in read/write on 64-bit machines.

[Mateusz Kulikowski]

ulpi_read and ulpi_write are used to read/write registers via ULPI bus.
Code generates compilation warnings on 64-bit machines where pointer
is cast to u32.

This patch drops all but last 8 bits of register address.
It is possible, because addresses on ULPI bus are 6- or 8-bit.

It is not possible (according to ULPI 1.1 spec) to have more
than 8-bit addressing.

This patch should not cause regressions as all calls to
ulpi_read/write use either structure pointer (@ address 0) or integer
offsets cast to pointer - addresses requested are way below 8-bit range.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
---

Changes in v3:
- New patch

Changes in v2: None
Changes in v1: None

 drivers/usb/ulpi/ulpi-viewport.c | 5 +++--
 include/usb/ulpi.h               | 2 ++
 2 files changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/ulpi/ulpi-viewport.c b/drivers/usb/ulpi/ulpi-viewport.c
index 72a06de..d111680 100644
--- a/drivers/usb/ulpi/ulpi-viewport.c
+++ b/drivers/usb/ulpi/ulpi-viewport.c
@@ -92,7 +92,8 @@ static int ulpi_request(struct ulpi_viewport *ulpi_vp, u32 value)
 
 int ulpi_write(struct ulpi_viewport *ulpi_vp, u8 *reg, u32 value)
 {
-	u32 val = ULPI_RWRUN | ULPI_RWCTRL | ((u32)reg << 16) | (value & 0xff);
+	u32 addr = (uintptr_t)reg & 0xFF;
+	u32 val = ULPI_RWRUN | ULPI_RWCTRL | addr << 16 | (value & 0xff);
 
 	val |= (ulpi_vp->port_num & 0x7) << 24;
 	return ulpi_request(ulpi_vp, val);
@@ -101,7 +102,7 @@ int ulpi_write(struct ulpi_viewport *ulpi_vp, u8 *reg, u32 value)
 u32 ulpi_read(struct ulpi_viewport *ulpi_vp, u8 *reg)
 {
 	int err;
-	u32 val = ULPI_RWRUN | ((u32)reg << 16);
+	u32 val = ULPI_RWRUN | ((uintptr_t)reg & 0xFF) << 16;
 
 	val |= (ulpi_vp->port_num & 0x7) << 24;
 	err = ulpi_request(ulpi_vp, val);
diff --git a/include/usb/ulpi.h b/include/usb/ulpi.h
index dfea395..747fb0a 100644
--- a/include/usb/ulpi.h
+++ b/include/usb/ulpi.h
@@ -123,6 +123,7 @@ int ulpi_reset(struct ulpi_viewport *ulpi_vp);
 /*
  * Write to the ULPI PHY register via the viewport.
  * @reg		- the ULPI register (one of the fields in struct ulpi_regs).
+ *		  Due to ULPI design, only 8 lsb of address are used.
  * @value	- the value - only 8 lower bits are used, others ignored.
  *
  * returns 0 on success, ULPI_ERROR on failure.
@@ -132,6 +133,7 @@ int ulpi_write(struct ulpi_viewport *ulpi_vp, u8 *reg, u32 value);
 /*
  * Read the ULPI PHY register content via the viewport.
  * @reg		- the ULPI register (one of the fields in struct ulpi_regs).
+ *		  Due to ULPI design, only 8 lsb of address are used.
  *
  * returns register content on success, ULPI_ERROR on failure.
  */
-- 
2.5.0

[U-Boot] [PATCH v3 09/21] eth: asix88179: Print packet length properly

[Mateusz Kulikowski]

Debug printf used '%u' to print size_t variable.
This caused warnings on 64-bit machines.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
---

Changes in v3:
- New patch

Changes in v2: None
Changes in v1: None

 drivers/usb/eth/asix88179.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/eth/asix88179.c b/drivers/usb/eth/asix88179.c
index cf4085d..5e1ea86 100644
--- a/drivers/usb/eth/asix88179.c
+++ b/drivers/usb/eth/asix88179.c
@@ -497,7 +497,7 @@ static int asix_send(struct eth_device *eth, void *packet, int length)
 				length + sizeof(packet_len) + sizeof(tx_hdr2),
 				&actual_len,
 				USB_BULK_SEND_TIMEOUT);
-	debug("Tx: len = %u, actual = %u, err = %d\n",
+	debug("Tx: len = %zu, actual = %u, err = %d\n",
 	      length + sizeof(packet_len), actual_len, err);
 
 	return err;
-- 
2.5.0

[U-Boot] [PATCH v3 10/21] usb: Rename ehci-fsl.h to ehci-ci.h

[Mateusz Kulikowski]

Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.

This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Add acked-by

Changes in v1: None

 drivers/usb/host/ehci-fsl.c           | 2 +-
 drivers/usb/host/ehci-mpc512x.c       | 2 +-
 drivers/usb/host/ehci-mx5.c           | 2 +-
 drivers/usb/host/ehci-mx6.c           | 2 +-
 drivers/usb/host/ehci-mxc.c           | 2 +-
 drivers/usb/host/ehci-vf.c            | 2 +-
 drivers/usb/host/ehci-zynq.c          | 2 +-
 include/usb/{ehci-fsl.h => ehci-ci.h} | 6 +++---
 8 files changed, 10 insertions(+), 10 deletions(-)
 rename include/usb/{ehci-fsl.h => ehci-ci.h} (99%)

diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c
index 97b7f14..4bcea9d 100644
--- a/drivers/usb/host/ehci-fsl.c
+++ b/drivers/usb/host/ehci-fsl.c
@@ -12,7 +12,7 @@
 #include <pci.h>
 #include <usb.h>
 #include <asm/io.h>
-#include <usb/ehci-fsl.h>
+#include <usb/ehci-ci.h>
 #include <hwconfig.h>
 #include <fsl_usb.h>
 #include <fdt_support.h>
diff --git a/drivers/usb/host/ehci-mpc512x.c b/drivers/usb/host/ehci-mpc512x.c
index b320c4a..4b50ac8 100644
--- a/drivers/usb/host/ehci-mpc512x.c
+++ b/drivers/usb/host/ehci-mpc512x.c
@@ -17,7 +17,7 @@
 #include <pci.h>
 #include <usb.h>
 #include <asm/io.h>
-#include <usb/ehci-fsl.h>
+#include <usb/ehci-ci.h>
 
 #include "ehci.h"
 
diff --git a/drivers/usb/host/ehci-mx5.c b/drivers/usb/host/ehci-mx5.c
index d319962..2b36ceb 100644
--- a/drivers/usb/host/ehci-mx5.c
+++ b/drivers/usb/host/ehci-mx5.c
@@ -9,7 +9,7 @@
 #include <usb.h>
 #include <errno.h>
 #include <linux/compiler.h>
-#include <usb/ehci-fsl.h>
+#include <usb/ehci-ci.h>
 #include <asm/io.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/clock.h>
diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
index e1c67f7..a981b50 100644
--- a/drivers/usb/host/ehci-mx6.c
+++ b/drivers/usb/host/ehci-mx6.c
@@ -10,7 +10,7 @@
 #include <errno.h>
 #include <wait_bit.h>
 #include <linux/compiler.h>
-#include <usb/ehci-fsl.h>
+#include <usb/ehci-ci.h>
 #include <asm/io.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/clock.h>
diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c
index f09c75a..f8324ee 100644
--- a/drivers/usb/host/ehci-mxc.c
+++ b/drivers/usb/host/ehci-mxc.c
@@ -9,7 +9,7 @@
 #include <usb.h>
 #include <asm/io.h>
 #include <asm/arch/imx-regs.h>
-#include <usb/ehci-fsl.h>
+#include <usb/ehci-ci.h>
 #include <errno.h>
 
 #include "ehci.h"
diff --git a/drivers/usb/host/ehci-vf.c b/drivers/usb/host/ehci-vf.c
index 335e303..61789dd 100644
--- a/drivers/usb/host/ehci-vf.c
+++ b/drivers/usb/host/ehci-vf.c
@@ -17,7 +17,7 @@
 #include <asm/arch/crm_regs.h>
 #include <asm/imx-common/iomux-v3.h>
 #include <asm/imx-common/regs-usbphy.h>
-#include <usb/ehci-fsl.h>
+#include <usb/ehci-ci.h>
 
 #include "ehci.h"
 
diff --git a/drivers/usb/host/ehci-zynq.c b/drivers/usb/host/ehci-zynq.c
index 7770d05..37a7935 100644
--- a/drivers/usb/host/ehci-zynq.c
+++ b/drivers/usb/host/ehci-zynq.c
@@ -11,7 +11,7 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/io.h>
 #include <usb.h>
-#include <usb/ehci-fsl.h>
+#include <usb/ehci-ci.h>
 #include <usb/ulpi.h>
 
 #include "ehci.h"
diff --git a/include/usb/ehci-fsl.h b/include/usb/ehci-ci.h
similarity index 99%
rename from include/usb/ehci-fsl.h
rename to include/usb/ehci-ci.h
index e9349b5..725aec5 100644
--- a/include/usb/ehci-fsl.h
+++ b/include/usb/ehci-ci.h
@@ -6,8 +6,8 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
-#ifndef _EHCI_FSL_H
-#define _EHCI_FSL_H
+#ifndef _EHCI_CI_H
+#define _EHCI_CI_H
 
 #include <asm/processor.h>
 
@@ -285,4 +285,4 @@ int usb_phy_mode(int port);
 int board_ehci_hcd_init(int port);
 int board_usb_phy_mode(int port);
 
-#endif /* _EHCI_FSL_H */
+#endif /* _EHCI_CI_H */
-- 
2.5.0

[U-Boot] [PATCH v3 11/21] usb: ehci-ci: Add missing registers.

[Mateusz Kulikowski]

Some registers of usb_ehci were marked as reserved.
This may be true for some variants of Chipidea USB core, but they have
meaning on other devices.

The following registers were added:
sbusstatus/sbusmode: AHB-related registers
genconfig*: Auxiluary IP core configuration registers.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>

---

Changes in v3: None
Changes in v2:
- Add reviewed-by

Changes in v1: None

 include/usb/ehci-ci.h | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/include/usb/ehci-ci.h b/include/usb/ehci-ci.h
index 725aec5..305b180 100644
--- a/include/usb/ehci-ci.h
+++ b/include/usb/ehci-ci.h
@@ -191,7 +191,11 @@ struct usb_ehci {
 	u32     gptimer1_ld;	/* 0x088 - General Purpose Timer 1 load value */
 	u32     gptimer1_ctrl;	/* 0x08C - General Purpose Timer 1 control */
 	u32	sbuscfg;	/* 0x090 - System Bus Interface Control */
-	u8	res2[0x6C];
+	u32	sbusstatus;	/* 0x094 - System Bus Interface Status */
+	u32	sbusmode;	/* 0x098 - System Bus Interface Mode */
+	u32	genconfig;	/* 0x09C - USB Core Configuration */
+	u32	genconfig2;	/* 0x0A0 - USB Core Configuration 2 */
+	u8	res2[0x5c];
 	u8	caplength;	/* 0x100 - Capability Register Length */
 	u8	res3[0x1];
 	u16	hciversion;	/* 0x102 - Host Interface Version */
-- 
2.5.0

[U-Boot] [PATCH v3 12/21] ehci-ci.h: drop generic USBCMD fields

[Mateusz Kulikowski]

Use definitions from ehci.h instead.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>

---

Changes in v3: None
Changes in v2:
- Add Acked-by

Changes in v1: None

 drivers/usb/host/ehci-mpc512x.c | 4 ++--
 include/usb/ehci-ci.h           | 4 ----
 2 files changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/host/ehci-mpc512x.c b/drivers/usb/host/ehci-mpc512x.c
index 4b50ac8..bb4f461 100644
--- a/drivers/usb/host/ehci-mpc512x.c
+++ b/drivers/usb/host/ehci-mpc512x.c
@@ -93,7 +93,7 @@ static int reset_usb_controller(volatile struct usb_ehci *ehci)
 	unsigned int i;
 
 	/* Command a reset of the USB Controller */
-	out_be32(&(ehci->usbcmd), EHCI_FSL_USBCMD_RST);
+	out_be32(&(ehci->usbcmd), CMD_RESET);
 
 	/* Wait for the reset process to finish */
 	for (i = 65535 ; i > 0 ; i--) {
@@ -101,7 +101,7 @@ static int reset_usb_controller(volatile struct usb_ehci *ehci)
 		 * The host will set this bit to zero once the
 		 * reset process is complete
 		 */
-		if ((in_be32(&(ehci->usbcmd)) & EHCI_FSL_USBCMD_RST) == 0)
+		if ((in_be32(&(ehci->usbcmd)) & CMD_RESET) == 0)
 			return 0;
 	}
 
diff --git a/include/usb/ehci-ci.h b/include/usb/ehci-ci.h
index 305b180..586d32a 100644
--- a/include/usb/ehci-ci.h
+++ b/include/usb/ehci-ci.h
@@ -97,10 +97,6 @@
 #define INTR_DATA_PULSING_EN	(0x1<<30)
 #define INTSTS_MASK		(0x00ff0000)
 
-/* USBCMD Bits of interest */
-#define EHCI_FSL_USBCMD_RST	(1 <<  1)
-#define EHCI_FSL_USBCMD_RS	(1 <<  0)
-
 #define  INTERRUPT_ENABLE_BITS_MASK  \
 		(INTR_USB_ID_EN		| \
 		INTR_1MS_TIMER_EN	| \
-- 
2.5.0

[U-Boot] [PATCH v3 13/21] ehci: Add support for Qualcomm EHCI

[Mateusz Kulikowski]

This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Use PORT_... macro to write to portsc
- Remove extra whitespace in probe()
- Add acked-by

Changes in v1:
- Reordered header files
- Removed braces around constant
- Added more verbose help to KConfig
- Added ULPI dependency to Kconfig
- Drop register #defines - use ehci-ci.h instead
- Create fixed ulpi viewport for device
- Use setbits/clearbits where possible
- Use wait_for_bit to reset controller
- Add dt binding documents

 doc/device-tree-bindings/usb/ehci-msm.txt |  10 ++
 drivers/usb/host/Kconfig                  |  11 ++
 drivers/usb/host/Makefile                 |   1 +
 drivers/usb/host/ehci-msm.c               | 178 ++++++++++++++++++++++++++++++
 4 files changed, 200 insertions(+)
 create mode 100644 doc/device-tree-bindings/usb/ehci-msm.txt
 create mode 100644 drivers/usb/host/ehci-msm.c

diff --git a/doc/device-tree-bindings/usb/ehci-msm.txt b/doc/device-tree-bindings/usb/ehci-msm.txt
new file mode 100644
index 0000000..205bb07
--- /dev/null
+++ b/doc/device-tree-bindings/usb/ehci-msm.txt
@@ -0,0 +1,10 @@
+Chipidea EHCI controller (part of OTG controller) used on Qualcomm devices.
+
+Required properties:
+- compatible: must be "qcom,ehci-host"
+- reg: start address and size of the registers
+
+ehci at 78d9000 {
+	compatible = "qcom,ehci-host";
+	reg = <0x78d9000 0x400>;
+};
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 9332374..d2363c8 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -74,6 +74,17 @@ config USB_EHCI_MX6
 	---help---
 	  Enables support for the on-chip EHCI controller on i.MX6 SoCs.
 
+config USB_EHCI_MSM
+	bool "Support for Qualcomm on-chip EHCI USB controller"
+	depends on DM_USB
+	select USB_ULPI_VIEWPORT
+	default n
+	---help---
+	  Enables support for the on-chip EHCI controller on Qualcomm
+	  Snapdragon SoCs.
+	  This driver supports combination of Chipidea USB controller
+	  and Synapsys USB PHY in host mode only.
+
 config USB_EHCI_GENERIC
 	bool "Support for generic EHCI USB controller"
 	depends on OF_CONTROL
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 9a87d2b..507519e 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_USB_EHCI_MX7) += ehci-mx6.o
 obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o
 obj-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
 obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o
+obj-$(CONFIG_USB_EHCI_MSM) += ehci-msm.o
 obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o
 obj-$(CONFIG_USB_EHCI_SPEAR) += ehci-spear.o
 obj-$(CONFIG_USB_EHCI_SUNXI) += ehci-sunxi.o
diff --git a/drivers/usb/host/ehci-msm.c b/drivers/usb/host/ehci-msm.c
new file mode 100644
index 0000000..6484c1c
--- /dev/null
+++ b/drivers/usb/host/ehci-msm.c
@@ -0,0 +1,178 @@
+/*
+ * Qualcomm EHCI driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * Based on Linux driver
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <libfdt.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+#include <usb/ulpi.h>
+#include <wait_bit.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <linux/compat.h>
+#include "ehci.h"
+
+/* PHY viewport regs */
+#define ULPI_MISC_A_READ         0x96
+#define ULPI_MISC_A_SET          0x97
+#define ULPI_MISC_A_CLEAR        0x98
+#define ULPI_MISC_A_VBUSVLDEXTSEL    (1 << 1)
+#define ULPI_MISC_A_VBUSVLDEXT       (1 << 0)
+
+#define GEN2_SESS_VLD_CTRL_EN (1 << 7)
+
+#define SESS_VLD_CTRL         (1 << 25)
+
+struct msm_ehci_priv {
+	struct ehci_ctrl ctrl; /* Needed by EHCI */
+	struct usb_ehci *ehci; /* Start of IP core*/
+	struct ulpi_viewport ulpi_vp; /* ULPI Viewport */
+};
+
+int __weak board_prepare_usb(enum usb_init_type type)
+{
+	return 0;
+}
+
+static void setup_usb_phy(struct msm_ehci_priv *priv)
+{
+	/* Select and enable external configuration with USB PHY */
+	ulpi_write(&priv->ulpi_vp, (u8 *)ULPI_MISC_A_SET,
+		   ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT);
+}
+
+static void reset_usb_phy(struct msm_ehci_priv *priv)
+{
+	/* Disable VBUS mimicing in the controller. */
+	ulpi_write(&priv->ulpi_vp, (u8 *)ULPI_MISC_A_CLEAR,
+		   ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT);
+}
+
+
+static int msm_init_after_reset(struct ehci_ctrl *dev)
+{
+	struct msm_ehci_priv *p = container_of(dev, struct msm_ehci_priv, ctrl);
+	struct usb_ehci *ehci = p->ehci;
+
+	/* select ULPI phy */
+	writel(PORT_PTS_ULPI, &ehci->portsc);
+	setup_usb_phy(p);
+
+	/* Enable sess_vld */
+	setbits_le32(&ehci->genconfig2, GEN2_SESS_VLD_CTRL_EN);
+
+	/* Enable external vbus configuration in the LINK */
+	setbits_le32(&ehci->usbcmd, SESS_VLD_CTRL);
+
+	/* USB_OTG_HS_AHB_BURST */
+	writel(0x0, &ehci->sbuscfg);
+
+	/* USB_OTG_HS_AHB_MODE: HPROT_MODE */
+	/* Bus access related config. */
+	writel(0x08, &ehci->sbusmode);
+
+	/* set mode to host controller */
+	writel(CM_HOST, &ehci->usbmode);
+
+	return 0;
+}
+
+static const struct ehci_ops msm_ehci_ops = {
+	.init_after_reset = msm_init_after_reset
+};
+
+static int ehci_usb_probe(struct udevice *dev)
+{
+	struct msm_ehci_priv *p = dev_get_priv(dev);
+	struct usb_ehci *ehci = p->ehci;
+	struct ehci_hccr *hccr;
+	struct ehci_hcor *hcor;
+	int ret;
+
+	hccr = (struct ehci_hccr *)((phys_addr_t)&ehci->caplength);
+	hcor = (struct ehci_hcor *)((phys_addr_t)hccr +
+			HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
+
+	ret = board_prepare_usb(USB_INIT_HOST);
+	if (ret < 0)
+		return ret;
+
+	return ehci_register(dev, hccr, hcor, &msm_ehci_ops, 0, USB_INIT_HOST);
+}
+
+static int ehci_usb_remove(struct udevice *dev)
+{
+	struct msm_ehci_priv *p = dev_get_priv(dev);
+	struct usb_ehci *ehci = p->ehci;
+	int ret;
+
+	ret = ehci_deregister(dev);
+	if (ret)
+		return ret;
+
+	/* Stop controller. */
+	clrbits_le32(&ehci->usbcmd, CMD_RUN);
+
+	reset_usb_phy(p);
+
+	ret = board_prepare_usb(USB_INIT_DEVICE); /* Board specific hook */
+	if (ret < 0)
+		return ret;
+
+	/* Reset controller */
+	setbits_le32(&ehci->usbcmd, CMD_RESET);
+
+	/* Wait for reset */
+	if (wait_for_bit(__func__, &ehci->usbcmd, CMD_RESET, false, 30,
+			 false)) {
+		printf("Stuck on USB reset.\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int ehci_usb_ofdata_to_platdata(struct udevice *dev)
+{
+	struct msm_ehci_priv *priv = dev_get_priv(dev);
+
+	priv->ulpi_vp.port_num = 0;
+	priv->ehci = (void *)dev_get_addr(dev);
+
+	if (priv->ehci == (void *)FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	/* Warning: this will not work if viewport address is > 64 bit due to
+	 * ULPI design.
+	 */
+	priv->ulpi_vp.viewport_addr = (phys_addr_t)&priv->ehci->ulpi_viewpoint;
+
+	return 0;
+}
+
+static const struct udevice_id ehci_usb_ids[] = {
+	{ .compatible = "qcom,ehci-host", },
+	{ }
+};
+
+U_BOOT_DRIVER(usb_ehci) = {
+	.name	= "ehci_msm",
+	.id	= UCLASS_USB,
+	.of_match = ehci_usb_ids,
+	.ofdata_to_platdata = ehci_usb_ofdata_to_platdata,
+	.probe = ehci_usb_probe,
+	.remove = ehci_usb_remove,
+	.ops	= &ehci_usb_ops,
+	.priv_auto_alloc_size = sizeof(struct msm_ehci_priv),
+	.flags	= DM_FLAG_ALLOC_PRIV_DMA,
+};
-- 
2.5.0

[U-Boot] [PATCH v3 14/21] drivers: Add SPMI bus uclass

[Mateusz Kulikowski]

Qualcom processors use proprietary bus to talk with PMIC devices -
SPMI (System Power Management Interface).
On wiring level it is similar to I2C, but on protocol level, it's
multi-master and has simple autodetection capabilities.
This commit adds simple uclass that provides bus read/write interface.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Use proper  entry order in Kconfig
- Rename CONFIG_DM_SPMI -> CONFIG_SPMI
- Fix header ordering
- Add reviewed-by

Changes in v1:
- Reorder includes
- Add read/write arguments documentation

 drivers/Kconfig            |  2 ++
 drivers/Makefile           |  1 +
 drivers/spmi/Kconfig       | 10 ++++++++++
 drivers/spmi/Makefile      |  7 +++++++
 drivers/spmi/spmi-uclass.c | 48 ++++++++++++++++++++++++++++++++++++++++++++++
 include/dm/uclass-id.h     |  1 +
 include/spmi/spmi.h        | 47 +++++++++++++++++++++++++++++++++++++++++++++
 7 files changed, 116 insertions(+)
 create mode 100644 drivers/spmi/Kconfig
 create mode 100644 drivers/spmi/Makefile
 create mode 100644 drivers/spmi/spmi-uclass.c
 create mode 100644 include/spmi/spmi.h

diff --git a/drivers/Kconfig b/drivers/Kconfig
index 70993fd..c82a94b 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -60,6 +60,8 @@ source "drivers/sound/Kconfig"
 
 source "drivers/spi/Kconfig"
 
+source "drivers/spmi/Kconfig"
+
 source "drivers/thermal/Kconfig"
 
 source "drivers/timer/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index e7eab66..6900097 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -54,6 +54,7 @@ obj-y += dfu/
 obj-$(CONFIG_X86) += pch/
 obj-y += rtc/
 obj-y += sound/
+obj-y += spmi/
 obj-y += timer/
 obj-y += tpm/
 obj-y += twserial/
diff --git a/drivers/spmi/Kconfig b/drivers/spmi/Kconfig
new file mode 100644
index 0000000..0b9bd31
--- /dev/null
+++ b/drivers/spmi/Kconfig
@@ -0,0 +1,10 @@
+menu "SPMI support"
+
+config SPMI
+	bool "Enable SPMI bus support"
+	depends on DM
+	---help---
+	  Select this to enable to support SPMI bus.
+	  SPMI (System Power Management Interface) bus is used
+	  to connect PMIC devices on various SoCs.
+endmenu
diff --git a/drivers/spmi/Makefile b/drivers/spmi/Makefile
new file mode 100644
index 0000000..99092eb
--- /dev/null
+++ b/drivers/spmi/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-$(CONFIG_SPMI)  += spmi-uclass.o
diff --git a/drivers/spmi/spmi-uclass.c b/drivers/spmi/spmi-uclass.c
new file mode 100644
index 0000000..4ddd51b
--- /dev/null
+++ b/drivers/spmi/spmi-uclass.c
@@ -0,0 +1,48 @@
+/*
+ * SPMI bus uclass driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <dm/root.h>
+#include <spmi/spmi.h>
+#include <linux/ctype.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int spmi_reg_read(struct udevice *dev, int usid, int pid, int reg)
+{
+	const struct dm_spmi_ops *ops = dev_get_driver_ops(dev);
+
+	if (!ops || !ops->read)
+		return -ENOSYS;
+
+	return ops->read(dev, usid, pid, reg);
+}
+
+int spmi_reg_write(struct udevice *dev, int usid, int pid, int reg,
+		   uint8_t value)
+{
+	const struct dm_spmi_ops *ops = dev_get_driver_ops(dev);
+
+	if (!ops || !ops->write)
+		return -ENOSYS;
+
+	return ops->write(dev, usid, pid, reg, value);
+}
+
+static int spmi_post_bind(struct udevice *dev)
+{
+	return dm_scan_fdt_node(dev, gd->fdt_blob, dev->of_offset, false);
+}
+
+UCLASS_DRIVER(spmi) = {
+	.id		= UCLASS_SPMI,
+	.name		= "spmi",
+	.post_bind	= spmi_post_bind,
+};
diff --git a/include/dm/uclass-id.h b/include/dm/uclass-id.h
index 3bea308..917d550 100644
--- a/include/dm/uclass-id.h
+++ b/include/dm/uclass-id.h
@@ -65,6 +65,7 @@ enum uclass_id {
 	UCLASS_RTC,		/* Real time clock device */
 	UCLASS_SERIAL,		/* Serial UART */
 	UCLASS_SPI,		/* SPI bus */
+	UCLASS_SPMI,		/* System Power Management Interface bus */
 	UCLASS_SPI_FLASH,	/* SPI flash */
 	UCLASS_SPI_GENERIC,	/* Generic SPI flash target */
 	UCLASS_SYSCON,		/* System configuration device */
diff --git a/include/spmi/spmi.h b/include/spmi/spmi.h
new file mode 100644
index 0000000..65a49bd
--- /dev/null
+++ b/include/spmi/spmi.h
@@ -0,0 +1,47 @@
+#ifndef _SPMI_SPMI_H
+#define _SPMI_SPMI_H
+
+/**
+ * struct dm_spmi_ops - SPMI device I/O interface
+ *
+ * Should be implemented by UCLASS_SPMI device drivers. The standard
+ * device operations provides the I/O interface for it's childs.
+ *
+ * @read:      read register 'reg' of slave 'usid' and peripheral 'pid'
+ * @write:     write register 'reg' of slave 'usid' and peripheral 'pid'
+ *
+ * Each register is 8-bit, both read and write can return negative values
+ * on error.
+ */
+struct dm_spmi_ops {
+	int (*read)(struct udevice *dev, int usid, int pid, int reg);
+	int (*write)(struct udevice *dev, int usid, int pid, int reg,
+		     uint8_t value);
+};
+
+/**
+ * spmi_reg_read() - read a register from specific slave/peripheral
+ *
+ * @dev:	SPMI bus to read
+ * @usid	SlaveID
+ * @pid		Peripheral ID
+ * @reg:	Register to read
+ * @return value read on success or negative value of errno.
+ */
+int spmi_reg_read(struct udevice *dev, int usid, int pid, int reg);
+
+/**
+ * spmi_reg_write() - write a register of specific slave/peripheral
+ *
+ * @dev:	SPMI bus to write
+ * @usid	SlaveID
+ * @pid		Peripheral ID
+ * @reg:	Register to write
+ * @value:	Value to write
+ * @return 0 on success or negative value of errno.
+ */
+int spmi_reg_write(struct udevice *dev, int usid, int pid, int reg,
+		   uint8_t value);
+
+#endif
+
-- 
2.5.0

[U-Boot] [PATCH v3 15/21] spmi: Add sandbox test driver

[Mateusz Kulikowski]

This patch adds emulated spmi bus controller with part of
pm8916 pmic on it to sandbox and tests validating SPMI uclass.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
---

Changes in v3:
- Updated test.dts to include SPMI like sandbox.dts does

Changes in v2:
- Rename CONFIG_DM_SPMI -> CONFIG_SPMI
- Rename r -> regs, p -> priv
- Add reviewed-by
- Update binding doc (drop unused bindig)

Changes in v1: None

 arch/sandbox/dts/sandbox.dts                   |  20 ++++
 arch/sandbox/dts/test.dts                      |  20 ++++
 configs/sandbox_defconfig                      |   4 +
 doc/device-tree-bindings/spmi/spmi-sandbox.txt |  31 +++++
 drivers/spmi/Kconfig                           |   8 ++
 drivers/spmi/Makefile                          |   1 +
 drivers/spmi/spmi-sandbox.c                    | 157 +++++++++++++++++++++++++
 test/dm/Makefile                               |   1 +
 test/dm/spmi.c                                 | 115 ++++++++++++++++++
 9 files changed, 357 insertions(+)
 create mode 100644 doc/device-tree-bindings/spmi/spmi-sandbox.txt
 create mode 100644 drivers/spmi/spmi-sandbox.c
 create mode 100644 test/dm/spmi.c

diff --git a/arch/sandbox/dts/sandbox.dts b/arch/sandbox/dts/sandbox.dts
index e3f02bf..2ae4014 100644
--- a/arch/sandbox/dts/sandbox.dts
+++ b/arch/sandbox/dts/sandbox.dts
@@ -240,6 +240,26 @@
 		status = "disabled";
 	};
 
+	spmi: spmi at 0 {
+		compatible = "sandbox,spmi";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		pm8916 at 0 {
+			compatible = "qcom,spmi-pmic";
+			reg = <0x0 0x1>;
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+
+			spmi_gpios: gpios at c000 {
+				compatible = "qcom,pm8916-gpio";
+				reg = <0xc000 0x400>;
+				gpio-controller;
+				gpio-count = <4>;
+				#gpio-cells = <2>;
+				gpio-bank-name="spmi";
+			};
+		};
+	};
 };
 
 #include "cros-ec-keyboard.dtsi"
diff --git a/arch/sandbox/dts/test.dts b/arch/sandbox/dts/test.dts
index 9b8d658..8930009 100644
--- a/arch/sandbox/dts/test.dts
+++ b/arch/sandbox/dts/test.dts
@@ -351,6 +351,26 @@
 		status = "disabled";
 	};
 
+	spmi: spmi at 0 {
+		compatible = "sandbox,spmi";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		pm8916 at 0 {
+			compatible = "qcom,spmi-pmic";
+			reg = <0x0 0x1>;
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+
+			spmi_gpios: gpios at c000 {
+				compatible = "qcom,pm8916-gpio";
+				reg = <0xc000 0x400>;
+				gpio-controller;
+				gpio-count = <4>;
+				#gpio-cells = <2>;
+				gpio-bank-name="spmi";
+			};
+		};
+	};
 };
 
 #include "sandbox_pmic.dtsi"
diff --git a/configs/sandbox_defconfig b/configs/sandbox_defconfig
index 02534bf..d77710d 100644
--- a/configs/sandbox_defconfig
+++ b/configs/sandbox_defconfig
@@ -30,6 +30,7 @@ CONFIG_ADC=y
 CONFIG_ADC_SANDBOX=y
 CONFIG_CLK=y
 CONFIG_SANDBOX_GPIO=y
+CONFIG_PM8916_GPIO=y
 CONFIG_SYS_I2C_SANDBOX=y
 CONFIG_CROS_EC_KEYB=y
 CONFIG_LED=y
@@ -58,6 +59,9 @@ CONFIG_PINCONF=y
 CONFIG_PINCTRL_SANDBOX=y
 CONFIG_DM_PMIC=y
 CONFIG_DM_PMIC_SANDBOX=y
+CONFIG_PMIC_PM8916=y
+CONFIG_SPMI=y
+CONFIG_SPMI_SANDBOX=y
 CONFIG_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_SANDBOX=y
 CONFIG_RAM=y
diff --git a/doc/device-tree-bindings/spmi/spmi-sandbox.txt b/doc/device-tree-bindings/spmi/spmi-sandbox.txt
new file mode 100644
index 0000000..8569a1a
--- /dev/null
+++ b/doc/device-tree-bindings/spmi/spmi-sandbox.txt
@@ -0,0 +1,31 @@
+Sandbox SPMI emulated arbiter.
+
+This is bus driver for Sandbox. It includes part of emulated pm8916 pmic.
+
+Required properties:
+- compatible: "sandbox,spmi"
+- #address-cells: 0x1 - childs slave ID address
+- #size-cells: 0x1
+
+Example:
+
+spmi: spmi at 0 {
+	compatible = "sandbox,spmi";
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+	pm8916 at 0 {
+		compatible = "qcom,spmi-pmic";
+		reg = <0x0 0x1>;
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+
+		spmi_gpios: gpios at c000 {
+			compatible = "qcom,pm8916-gpio";
+			reg = <0xc000 0x400>;
+			gpio-controller;
+			gpio-count = <4>;
+			#gpio-cells = <2>;
+			gpio-bank-name="spmi";
+		};
+	};
+};
diff --git a/drivers/spmi/Kconfig b/drivers/spmi/Kconfig
index 0b9bd31..c70d675 100644
--- a/drivers/spmi/Kconfig
+++ b/drivers/spmi/Kconfig
@@ -7,4 +7,12 @@ config SPMI
 	  Select this to enable to support SPMI bus.
 	  SPMI (System Power Management Interface) bus is used
 	  to connect PMIC devices on various SoCs.
+
+config SPMI_SANDBOX
+	boolean "Support for Sandbox SPMI bus"
+	depends on SPMI
+	---help---
+	  Demo SPMI bus implementation. Emulates part of PM8916 as single
+          slave (0) on bus. It has 4 GPIO peripherals, pid 0xC0-0xC3.
+
 endmenu
diff --git a/drivers/spmi/Makefile b/drivers/spmi/Makefile
index 99092eb..4ca65a9 100644
--- a/drivers/spmi/Makefile
+++ b/drivers/spmi/Makefile
@@ -5,3 +5,4 @@
 #
 
 obj-$(CONFIG_SPMI)  += spmi-uclass.o
+obj-$(CONFIG_SPMI_SANDBOX) += spmi-sandbox.o
diff --git a/drivers/spmi/spmi-sandbox.c b/drivers/spmi/spmi-sandbox.c
new file mode 100644
index 0000000..2f0fea0
--- /dev/null
+++ b/drivers/spmi/spmi-sandbox.c
@@ -0,0 +1,157 @@
+/*
+ * Sample SPMI bus driver
+ *
+ * It emulates bus with single pm8916-like pmic that has only GPIO reigsters.
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <spmi/spmi.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define EMUL_GPIO_PID_START 0xC0
+#define EMUL_GPIO_PID_END   0xC3
+
+#define EMUL_GPIO_COUNT 4
+
+#define EMUL_GPIO_REG_END 0x46 /* Last valid register */
+
+#define EMUL_PERM_R 0x1
+#define EMUL_PERM_W 0x2
+#define EMUL_PERM_RW (EMUL_PERM_R | EMUL_PERM_W)
+
+struct sandbox_emul_fake_regs {
+	u8 value;
+	u8 access_mask;
+	u8 perms; /* Access permissions */
+};
+
+struct sandbox_emul_gpio {
+	struct sandbox_emul_fake_regs r[EMUL_GPIO_REG_END]; /* Fake registers */
+};
+
+struct sandbox_spmi_priv {
+	struct sandbox_emul_gpio gpios[EMUL_GPIO_COUNT];
+};
+
+/* Check if valid register was requested */
+static bool check_address_valid(int usid, int pid, int off)
+{
+	if (usid != 0)
+		return false;
+	if (pid < EMUL_GPIO_PID_START || pid > EMUL_GPIO_PID_END)
+		return false;
+	if (off > EMUL_GPIO_REG_END)
+		return false;
+	return true;
+}
+
+static int sandbox_spmi_write(struct udevice *dev, int usid, int pid, int off,
+			  uint8_t val)
+{
+	struct sandbox_spmi_priv *priv = dev_get_priv(dev);
+	struct sandbox_emul_fake_regs *regs;
+
+	if (!check_address_valid(usid, pid, off))
+		return -EIO;
+
+	regs = priv->gpios[pid & 0x3].r; /* Last 3 bits of pid are gpio # */
+
+	switch (off) {
+	case 0x40: /* Control */
+		val &= regs[off].access_mask;
+		if (((val & 0x30) == 0x10) || ((val & 0x30) == 0x20)) {
+			/* out/inout - set status register */
+			regs[0x8].value &= ~0x1;
+			regs[0x8].value |= val & 0x1;
+		}
+		break;
+	default:
+		if (regs[off].perms & EMUL_PERM_W)
+			regs[off].value = val & regs[off].access_mask;
+	}
+	return 0;
+}
+
+static int sandbox_spmi_read(struct udevice *dev, int usid, int pid, int off)
+{
+	struct sandbox_spmi_priv *priv = dev_get_priv(dev);
+	struct sandbox_emul_fake_regs *regs;
+
+	if (!check_address_valid(usid, pid, off))
+		return -EIO;
+
+	regs = priv->gpios[pid & 0x3].r; /* Last 3 bits of pid are gpio # */
+
+	if (regs[0x46].value == 0) /* Block disabled */
+		return 0;
+
+	switch (off) {
+	case 0x8: /* Status */
+		if (regs[0x46].value == 0) /* Block disabled */
+			return 0;
+		return regs[off].value;
+	default:
+		if (regs[off].perms & EMUL_PERM_R)
+			return regs[off].value;
+		else
+			return 0;
+	}
+}
+
+static struct dm_spmi_ops sandbox_spmi_ops = {
+	.read = sandbox_spmi_read,
+	.write = sandbox_spmi_write,
+};
+
+static int sandbox_spmi_probe(struct udevice *dev)
+{
+	struct sandbox_spmi_priv *priv = dev_get_priv(dev);
+	int i;
+
+	for (i = 0; i < EMUL_GPIO_COUNT; ++i) {
+		struct sandbox_emul_fake_regs *regs = priv->gpios[i].r;
+		regs[4].perms = EMUL_PERM_R;
+		regs[4].value = 0x10;
+		regs[5].perms = EMUL_PERM_R;
+		regs[5].value = 0x5;
+		regs[8].access_mask = 0x81;
+		regs[8].perms = EMUL_PERM_RW;
+		regs[0x40].access_mask = 0x7F;
+		regs[0x40].perms = EMUL_PERM_RW;
+		regs[0x41].access_mask = 7;
+		regs[0x41].perms = EMUL_PERM_RW;
+		regs[0x42].access_mask = 7;
+		regs[0x42].perms = EMUL_PERM_RW;
+		regs[0x42].value = 0x4;
+		regs[0x45].access_mask = 0x3F;
+		regs[0x45].perms = EMUL_PERM_RW;
+		regs[0x45].value = 0x1;
+		regs[0x46].access_mask = 0x80;
+		regs[0x46].perms = EMUL_PERM_RW;
+		regs[0x46].value = 0x80;
+	}
+	return 0;
+}
+
+static const struct udevice_id sandbox_spmi_ids[] = {
+	{ .compatible = "sandbox,spmi" },
+	{ }
+};
+
+U_BOOT_DRIVER(msm_spmi) = {
+	.name = "sandbox_spmi",
+	.id = UCLASS_SPMI,
+	.of_match = sandbox_spmi_ids,
+	.ops = &sandbox_spmi_ops,
+	.probe = sandbox_spmi_probe,
+	.priv_auto_alloc_size = sizeof(struct sandbox_spmi_priv),
+};
diff --git a/test/dm/Makefile b/test/dm/Makefile
index fd0198f..ab33cd6 100644
--- a/test/dm/Makefile
+++ b/test/dm/Makefile
@@ -36,4 +36,5 @@ obj-$(CONFIG_DM_REGULATOR) += regulator.o
 obj-$(CONFIG_TIMER) += timer.o
 obj-$(CONFIG_DM_VIDEO) += video.o
 obj-$(CONFIG_ADC) += adc.o
+obj-$(CONFIG_SPMI) += spmi.o
 endif
diff --git a/test/dm/spmi.c b/test/dm/spmi.c
new file mode 100644
index 0000000..81767f6
--- /dev/null
+++ b/test/dm/spmi.c
@@ -0,0 +1,115 @@
+/*
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <dm.h>
+#include <dm/device.h>
+#include <dm/root.h>
+#include <dm/test.h>
+#include <dm/util.h>
+#include <power/pmic.h>
+#include <spmi/spmi.h>
+#include <asm/gpio.h>
+#include <test/ut.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Test if bus childs got probed propperly*/
+static int dm_test_spmi_probe(struct unit_test_state *uts)
+{
+	const char *name = "spmi at 0";
+	struct udevice *bus, *dev;
+
+	ut_assertok(uclass_get_device(UCLASS_SPMI, 0, &bus));
+
+	/* Check bus name */
+	ut_asserteq_str(name, bus->name);
+
+	/* Check that it has some devices */
+	ut_asserteq(device_has_children(bus), true);
+
+	ut_assertok(device_find_first_child(bus, &dev));
+
+	/* There should be at least one child */
+	ut_assertnonnull(dev);
+
+	/* Check that only PMICs are connected to the bus */
+	while (dev) {
+		ut_asserteq(device_get_uclass_id(dev), UCLASS_PMIC);
+		device_find_next_child(&dev);
+	}
+
+	return 0;
+}
+DM_TEST(dm_test_spmi_probe, DM_TESTF_SCAN_FDT);
+
+/* Test if it's possible to read bus directly and indirectly */
+static int dm_test_spmi_access(struct unit_test_state *uts)
+{
+	const char *pmic_name = "pm8916 at 0";
+	struct udevice *bus, *pmic;
+
+	ut_assertok(uclass_get_device(UCLASS_SPMI, 0, &bus));
+
+	ut_assertok(device_get_child(bus, 0, &pmic));
+
+	/* Sanity check if it's proper PMIC */
+	ut_asserteq_str(pmic_name, pmic->name);
+
+	/* Read PMIC ID reg using SPMI bus - it assumes it has slaveID == 0*/
+	ut_asserteq(spmi_reg_read(bus, 0, 0xC0, 0x4), 0x10);
+	ut_asserteq(spmi_reg_read(bus, 0, 0xC0, 0x5), 0x5);
+
+	/* Read ID reg via pmic interface */
+	ut_asserteq(pmic_reg_read(pmic, 0xC004), 0x10);
+	ut_asserteq(pmic_reg_read(pmic, 0xC005), 0x5);
+
+	return 0;
+}
+DM_TEST(dm_test_spmi_access, DM_TESTF_SCAN_FDT);
+
+
+/* Test if it's possible to access GPIO that should be in pmic */
+static int dm_test_spmi_access_peripheral(struct unit_test_state *uts)
+{
+	struct udevice *dev;
+	unsigned int offset, gpio;
+	const char *name;
+	int offset_count;
+
+	/* Get second pin of PMIC GPIO */
+	ut_assertok(gpio_lookup_name("spmi1", &dev, &offset, &gpio));
+
+	/* Check if PMIC is parent */
+	ut_asserteq(device_get_uclass_id(dev->parent), UCLASS_PMIC);
+
+	/* This should be second gpio */
+	ut_asserteq(1, offset);
+
+	name = gpio_get_bank_info(dev, &offset_count);
+
+	/* Check bank name */
+	ut_asserteq_str("spmi", name);
+	/* Check pin count */
+	ut_asserteq(4, offset_count);
+
+	ut_assertok(gpio_request(gpio, "testing"));
+
+	/* Try to set/clear gpio */
+	ut_assertok(gpio_direction_output(gpio, 0));
+	ut_asserteq(gpio_get_value(gpio), 0);
+	ut_assertok(gpio_direction_output(gpio, 1));
+	ut_asserteq(gpio_get_value(gpio), 1);
+	ut_assertok(gpio_direction_input(gpio));
+	ut_asserteq(gpio_get_value(gpio), 1);
+
+	ut_assertok(gpio_free(gpio));
+
+	return 0;
+}
+DM_TEST(dm_test_spmi_access_peripheral, DM_TESTF_SCAN_FDT);
+
-- 
2.5.0

[U-Boot] [PATCH v3 16/21] drivers: spmi: Add support for Qualcomm SPMI bus driver

[Mateusz Kulikowski]

Support SPMI arbiter on Qualcomm Snapdragon devices.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Rename DM_SPMI -> SPMI
- Rename p -> priv (in write/read)
- Fix header ordering (again)
- Add reviewed-by

Changes in v1:
- add binding documentation and better Kconfig help
- Changed a bit mapping
- Change include order
- Use clrsetbits* where possible
- Add one more supported dts id
- Handle missing fields in dt properly

 doc/device-tree-bindings/spmi/spmi-msm.txt |  26 ++++
 drivers/spmi/Kconfig                       |   7 +-
 drivers/spmi/Makefile                      |   1 +
 drivers/spmi/spmi-msm.c                    | 189 +++++++++++++++++++++++++++++
 4 files changed, 222 insertions(+), 1 deletion(-)
 create mode 100644 doc/device-tree-bindings/spmi/spmi-msm.txt
 create mode 100644 drivers/spmi/spmi-msm.c

diff --git a/doc/device-tree-bindings/spmi/spmi-msm.txt b/doc/device-tree-bindings/spmi/spmi-msm.txt
new file mode 100644
index 0000000..ae47673
--- /dev/null
+++ b/doc/device-tree-bindings/spmi/spmi-msm.txt
@@ -0,0 +1,26 @@
+Qualcomm SPMI arbiter/bus driver
+
+This is bus driver for Qualcomm chips that use SPMI to communicate with PMICs.
+
+Required properties:
+- compatible: "qcom,spmi-pmic-arb"
+- reg: Register block adresses and sizes for various parts of device:
+   1) PMIC arbiter channel mapping base (PMIC_ARB_REG_CHNLn)
+   2) SPMI write command (master) registers (PMIC_ARB_CORE_SW_DEC_CHANNELS)
+   3) SPMI read command (observer) registers (PMIC_ARB_CORE_REGISTERS_OBS)
+
+Optional properties (if not set by parent):
+- #address-cells: 0x1 - childs slave ID address
+- #size-cells: 0x1
+
+All PMICs should be placed as a child nodes of bus arbiter.
+Automatic detection of childs is currently not supported.
+
+Example:
+
+spmi at 200f000 {
+	compatible = "qcom,spmi-pmic-arb";
+	reg = <0x200f800 0x200 0x2400000 0x400000 0x2c00000 0x400000>;
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+};
diff --git a/drivers/spmi/Kconfig b/drivers/spmi/Kconfig
index c70d675..8d25b45 100644
--- a/drivers/spmi/Kconfig
+++ b/drivers/spmi/Kconfig
@@ -8,11 +8,16 @@ config SPMI
 	  SPMI (System Power Management Interface) bus is used
 	  to connect PMIC devices on various SoCs.
 
+config SPMI_MSM
+	boolean "Support Qualcomm SPMI bus"
+	depends on SPMI
+	---help---
+	  Support SPMI bus implementation found on Qualcomm Snapdragon SoCs.
+
 config SPMI_SANDBOX
 	boolean "Support for Sandbox SPMI bus"
 	depends on SPMI
 	---help---
 	  Demo SPMI bus implementation. Emulates part of PM8916 as single
           slave (0) on bus. It has 4 GPIO peripherals, pid 0xC0-0xC3.
-
 endmenu
diff --git a/drivers/spmi/Makefile b/drivers/spmi/Makefile
index 4ca65a9..c0b1220 100644
--- a/drivers/spmi/Makefile
+++ b/drivers/spmi/Makefile
@@ -5,4 +5,5 @@
 #
 
 obj-$(CONFIG_SPMI)  += spmi-uclass.o
+obj-$(CONFIG_SPMI_MSM) += spmi-msm.o
 obj-$(CONFIG_SPMI_SANDBOX) += spmi-sandbox.o
diff --git a/drivers/spmi/spmi-msm.c b/drivers/spmi/spmi-msm.c
new file mode 100644
index 0000000..0cef505
--- /dev/null
+++ b/drivers/spmi/spmi-msm.c
@@ -0,0 +1,189 @@
+/*
+ * Qualcomm SPMI bus driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * Loosely based on Little Kernel driver
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <asm/io.h>
+#include <spmi/spmi.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ARB_CHANNEL_OFFSET(n)		(0x4 * (n))
+#define SPMI_CH_OFFSET(chnl)		((chnl) * 0x8000)
+
+#define SPMI_REG_CMD0			0x0
+#define SPMI_REG_CONFIG			0x4
+#define SPMI_REG_STATUS			0x8
+#define SPMI_REG_WDATA			0x10
+#define SPMI_REG_RDATA			0x18
+
+#define SPMI_CMD_OPCODE_SHIFT		27
+#define SPMI_CMD_SLAVE_ID_SHIFT		20
+#define SPMI_CMD_ADDR_SHIFT		12
+#define SPMI_CMD_ADDR_OFFSET_SHIFT	4
+#define SPMI_CMD_BYTE_CNT_SHIFT		0
+
+#define SPMI_CMD_EXT_REG_WRITE_LONG	0x00
+#define SPMI_CMD_EXT_REG_READ_LONG	0x01
+
+#define SPMI_STATUS_DONE		0x1
+
+#define SPMI_MAX_CHANNELS	128
+#define SPMI_MAX_SLAVES		16
+#define SPMI_MAX_PERIPH		256
+
+struct msm_spmi_priv {
+	phys_addr_t arb_chnl; /* ARB channel mapping base */
+	phys_addr_t spmi_core; /* SPMI core */
+	phys_addr_t spmi_obs; /* SPMI observer */
+	/* SPMI channel map */
+	uint8_t channel_map[SPMI_MAX_SLAVES][SPMI_MAX_PERIPH];
+};
+
+static int msm_spmi_write(struct udevice *dev, int usid, int pid, int off,
+			  uint8_t val)
+{
+	struct msm_spmi_priv *priv = dev_get_priv(dev);
+	unsigned channel;
+	uint32_t reg = 0;
+
+	if (usid >= SPMI_MAX_SLAVES)
+		return -EIO;
+	if (pid >= SPMI_MAX_PERIPH)
+		return -EIO;
+
+	channel = priv->channel_map[usid][pid];
+
+	/* Disable IRQ mode for the current channel*/
+	writel(0x0, priv->spmi_core + SPMI_CH_OFFSET(channel) +
+	       SPMI_REG_CONFIG);
+
+	/* Write single byte */
+	writel(val, priv->spmi_core + SPMI_CH_OFFSET(channel) + SPMI_REG_WDATA);
+
+	/* Prepare write command */
+	reg |= SPMI_CMD_EXT_REG_WRITE_LONG << SPMI_CMD_OPCODE_SHIFT;
+	reg |= (usid << SPMI_CMD_SLAVE_ID_SHIFT);
+	reg |= (pid << SPMI_CMD_ADDR_SHIFT);
+	reg |= (off << SPMI_CMD_ADDR_OFFSET_SHIFT);
+	reg |= 1; /* byte count */
+
+	/* Send write command */
+	writel(reg, priv->spmi_core + SPMI_CH_OFFSET(channel) + SPMI_REG_CMD0);
+
+	/* Wait till CMD DONE status */
+	reg = 0;
+	while (!reg) {
+		reg = readl(priv->spmi_core + SPMI_CH_OFFSET(channel) +
+			    SPMI_REG_STATUS);
+	}
+
+	if (reg ^ SPMI_STATUS_DONE) {
+		printf("SPMI write failure.\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int msm_spmi_read(struct udevice *dev, int usid, int pid, int off)
+{
+	struct msm_spmi_priv *priv = dev_get_priv(dev);
+	unsigned channel;
+	uint32_t reg = 0;
+
+	if (usid >= SPMI_MAX_SLAVES)
+		return -EIO;
+	if (pid >= SPMI_MAX_PERIPH)
+		return -EIO;
+
+	channel = priv->channel_map[usid][pid];
+
+	/* Disable IRQ mode for the current channel*/
+	writel(0x0, priv->spmi_obs + SPMI_CH_OFFSET(channel) + SPMI_REG_CONFIG);
+
+	/* Prepare read command */
+	reg |= SPMI_CMD_EXT_REG_READ_LONG << SPMI_CMD_OPCODE_SHIFT;
+	reg |= (usid << SPMI_CMD_SLAVE_ID_SHIFT);
+	reg |= (pid << SPMI_CMD_ADDR_SHIFT);
+	reg |= (off << SPMI_CMD_ADDR_OFFSET_SHIFT);
+	reg |= 1; /* byte count */
+
+	/* Request read */
+	writel(reg, priv->spmi_obs + SPMI_CH_OFFSET(channel) + SPMI_REG_CMD0);
+
+	/* Wait till CMD DONE status */
+	reg = 0;
+	while (!reg) {
+		reg = readl(priv->spmi_obs + SPMI_CH_OFFSET(channel) +
+			    SPMI_REG_STATUS);
+	}
+
+	if (reg ^ SPMI_STATUS_DONE) {
+		printf("SPMI read failure.\n");
+		return -EIO;
+	}
+
+	/* Read the data */
+	return readl(priv->spmi_obs + SPMI_CH_OFFSET(channel) +
+		     SPMI_REG_RDATA) & 0xFF;
+}
+
+static struct dm_spmi_ops msm_spmi_ops = {
+	.read = msm_spmi_read,
+	.write = msm_spmi_write,
+};
+
+static int msm_spmi_probe(struct udevice *dev)
+{
+	struct udevice *parent = dev->parent;
+	struct msm_spmi_priv *priv = dev_get_priv(dev);
+	int i;
+
+	priv->arb_chnl = dev_get_addr(dev);
+	priv->spmi_core = fdtdec_get_addr_size_auto_parent(gd->fdt_blob,
+							   parent->of_offset,
+							   dev->of_offset,
+							   "reg", 1, NULL);
+	priv->spmi_obs = fdtdec_get_addr_size_auto_parent(gd->fdt_blob,
+							  parent->of_offset,
+							  dev->of_offset, "reg",
+							  2, NULL);
+	if (priv->arb_chnl == FDT_ADDR_T_NONE ||
+	    priv->spmi_core == FDT_ADDR_T_NONE ||
+	    priv->spmi_obs == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	/* Scan peripherals connected to each SPMI channel */
+	for (i = 0; i < SPMI_MAX_CHANNELS ; i++) {
+		uint32_t periph = readl(priv->arb_chnl + ARB_CHANNEL_OFFSET(i));
+		uint8_t slave_id = (periph & 0xf0000) >> 16;
+		uint8_t pid = (periph & 0xff00) >> 8;
+
+		priv->channel_map[slave_id][pid] = i;
+	}
+	return 0;
+}
+
+static const struct udevice_id msm_spmi_ids[] = {
+	{ .compatible = "qcom,spmi-pmic-arb" },
+	{ }
+};
+
+U_BOOT_DRIVER(msm_spmi) = {
+	.name = "msm_spmi",
+	.id = UCLASS_SPMI,
+	.of_match = msm_spmi_ids,
+	.ops = &msm_spmi_ops,
+	.probe = msm_spmi_probe,
+	.priv_auto_alloc_size = sizeof(struct msm_spmi_priv),
+};
-- 
2.5.0

[U-Boot] [PATCH v3 17/21] pmic: Add support for Qualcomm PM8916 PMIC

[Mateusz Kulikowski]

This PMIC is connected on SPMI bus so needs SPMI support enabled.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Add reviewed-by
- Reordered Kconfig & Makefile (to keep alphabetical ordering)
- Added link to dt binding @ help

Changes in v1:
- Added dt bindings
- Reoder includes
- Replaced extract_* macros with ordinary shift/mask
- Added error checking and whitespaces in probe

 doc/device-tree-bindings/pmic/pm8916.txt | 18 ++++++
 drivers/power/pmic/Kconfig               | 16 ++++++
 drivers/power/pmic/Makefile              |  1 +
 drivers/power/pmic/pm8916.c              | 96 ++++++++++++++++++++++++++++++++
 4 files changed, 131 insertions(+)
 create mode 100644 doc/device-tree-bindings/pmic/pm8916.txt
 create mode 100644 drivers/power/pmic/pm8916.c

diff --git a/doc/device-tree-bindings/pmic/pm8916.txt b/doc/device-tree-bindings/pmic/pm8916.txt
new file mode 100644
index 0000000..15c598b
--- /dev/null
+++ b/doc/device-tree-bindings/pmic/pm8916.txt
@@ -0,0 +1,18 @@
+Qualcomm pm8916 PMIC
+
+This PMIC is connected using SPMI bus so should be child of SPMI bus controller.
+
+Required properties:
+- compatible: "qcom,spmi-pmic";
+- reg: SPMI Slave ID, size (ignored)
+- #address-cells: 0x1 (peripheral ID)
+- #size-cells: 0x1 (size of peripheral register space)
+
+Example:
+
+pm8916 at 0 {
+	compatible = "qcom,spmi-pmic";
+	reg = <0x0 0x1>;
+	#address-cells = <0x1>;
+	#size-cells = <0x1>;
+};
diff --git a/drivers/power/pmic/Kconfig b/drivers/power/pmic/Kconfig
index 7f69ae1..69f8d51 100644
--- a/drivers/power/pmic/Kconfig
+++ b/drivers/power/pmic/Kconfig
@@ -54,6 +54,22 @@ config DM_PMIC_MAX77686
 	This config enables implementation of driver-model pmic uclass features
 	for PMIC MAX77686. The driver implements read/write operations.
 
+config PMIC_PM8916
+	bool "Enable Driver Model for Qualcomm PM8916 PMIC"
+	depends on DM_PMIC
+	---help---
+	The PM8916 is a PMIC connected to one (or several) processors
+	with SPMI bus. It has 2 slaves with several peripherals:
+	- 18x LDO
+	- 4x GPIO
+	- Power and Reset buttons
+	- Watchdog
+	- RTC
+	- Vibrator drivers
+	- Others
+
+	Driver binding info: doc/device-tree-bindings/pmic/pm8916.txt
+
 config PMIC_RK808
 	bool "Enable support for Rockchip PMIC RK808"
 	depends on DM_PMIC
diff --git a/drivers/power/pmic/Makefile b/drivers/power/pmic/Makefile
index c6e8d0c..52b4f71 100644
--- a/drivers/power/pmic/Makefile
+++ b/drivers/power/pmic/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_DM_PMIC_PFUZE100) += pfuze100.o
 obj-$(CONFIG_PMIC_S2MPS11) += s2mps11.o
 obj-$(CONFIG_DM_PMIC_SANDBOX) += sandbox.o i2c_pmic_emul.o
 obj-$(CONFIG_PMIC_ACT8846) += act8846.o
+obj-$(CONFIG_PMIC_PM8916) += pm8916.o
 obj-$(CONFIG_PMIC_RK808) += rk808.o
 obj-$(CONFIG_PMIC_TPS65090) += tps65090.o
 obj-$(CONFIG_PMIC_S5M8767) += s5m8767.o
diff --git a/drivers/power/pmic/pm8916.c b/drivers/power/pmic/pm8916.c
new file mode 100644
index 0000000..9acf5f5
--- /dev/null
+++ b/drivers/power/pmic/pm8916.c
@@ -0,0 +1,96 @@
+/*
+ * Qualcomm pm8916 pmic driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <dm.h>
+#include <dm/root.h>
+#include <power/pmic.h>
+#include <spmi/spmi.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define PID_SHIFT 8
+#define PID_MASK (0xFF << PID_SHIFT)
+#define REG_MASK 0xFF
+
+struct pm8916_priv {
+	uint16_t usid; /* Slave ID on SPMI bus */
+};
+
+static int pm8916_reg_count(struct udevice *dev)
+{
+	return 0xFFFF;
+}
+
+static int pm8916_write(struct udevice *dev, uint reg, const uint8_t *buff,
+			int len)
+{
+	struct pm8916_priv *priv = dev_get_priv(dev);
+
+	if (len != 1)
+		return -EINVAL;
+
+	return spmi_reg_write(dev->parent, priv->usid,
+			      (reg & PID_MASK) >> PID_SHIFT, reg & REG_MASK,
+			      *buff);
+}
+
+static int pm8916_read(struct udevice *dev, uint reg, uint8_t *buff, int len)
+{
+	struct pm8916_priv *priv = dev_get_priv(dev);
+	int val;
+
+	if (len != 1)
+		return -EINVAL;
+
+	val = spmi_reg_read(dev->parent, priv->usid,
+			    (reg & PID_MASK) >> PID_SHIFT, reg & REG_MASK);
+
+	if (val < 0)
+		return val;
+	*buff = val;
+	return 0;
+}
+
+static struct dm_pmic_ops pm8916_ops = {
+	.reg_count = pm8916_reg_count,
+	.read = pm8916_read,
+	.write = pm8916_write,
+};
+
+static const struct udevice_id pm8916_ids[] = {
+	{ .compatible = "qcom,spmi-pmic" },
+	{ }
+};
+
+static int pm8916_probe(struct udevice *dev)
+{
+	struct pm8916_priv *priv = dev_get_priv(dev);
+
+	priv->usid = dev_get_addr(dev);
+
+	if (priv->usid == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	return 0;
+}
+
+
+static int pm8916_bind(struct udevice *dev)
+{
+	return dm_scan_fdt_node(dev, gd->fdt_blob, dev->of_offset, false);
+}
+
+U_BOOT_DRIVER(pmic_pm8916) = {
+	.name = "pmic_pm8916",
+	.id = UCLASS_PMIC,
+	.of_match = pm8916_ids,
+	.bind = pm8916_bind,
+	.probe = pm8916_probe,
+	.ops = &pm8916_ops,
+	.priv_auto_alloc_size = sizeof(struct pm8916_priv),
+};
-- 
2.5.0

[U-Boot] [PATCH v3 18/21] gpio: Add support for Qualcomm PM8916 gpios

[Mateusz Kulikowski]

This driver supports GPIOs present on PM8916 PMIC.
There are 2 device drivers inside:
- GPIO driver (4 "generic" GPIOs)
- Keypad driver that presents itself as GPIO with 2 inputs (power and reset)

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Add Reviewed-by

Changes in v1:
- Add binding doc
- Fixed inlcude ordering
- Merged direction_input and direction_output functions
- gpio_get: use switch instead of stacked if
- use pmic_clrsetbits
- add possibility to change prwkey bank name
- Handle invalid bindings
- Sanity HW check (i.e. check type/subtype registers)

 doc/device-tree-bindings/gpio/pm8916_gpio.txt |  48 ++++
 drivers/gpio/Kconfig                          |  10 +
 drivers/gpio/Makefile                         |   1 +
 drivers/gpio/pm8916_gpio.c                    | 302 ++++++++++++++++++++++++++
 4 files changed, 361 insertions(+)
 create mode 100644 doc/device-tree-bindings/gpio/pm8916_gpio.txt
 create mode 100644 drivers/gpio/pm8916_gpio.c

diff --git a/doc/device-tree-bindings/gpio/pm8916_gpio.txt b/doc/device-tree-bindings/gpio/pm8916_gpio.txt
new file mode 100644
index 0000000..58185b8
--- /dev/null
+++ b/doc/device-tree-bindings/gpio/pm8916_gpio.txt
@@ -0,0 +1,48 @@
+Driver for part of pm8916 PMIC - gpio and power/reset keys
+
+This device should be child of SPMI pmic.
+
+1) GPIO driver
+
+Required properties:
+- compatible: "qcom,pm8916-gpio"
+- reg: peripheral ID, size of register block
+- gpio-controller
+- gpio-count: number of GPIOs
+- #gpio-cells: 2
+
+Optional properties:
+- gpio-bank-name: name of bank (as default "pm8916" is used)
+
+Example:
+
+pmic_gpios: gpios at c000 {
+	compatible = "qcom,pm8916-gpio";
+	reg = <0xc000 0x400>;
+	gpio-controller;
+	gpio-count = <4>;
+	#gpio-cells = <2>;
+	gpio-bank-name="pmic";
+};
+
+
+2) Power/Reset key driver
+
+Required properties:
+- compatible: "qcom,pm8916-pwrkey"
+- reg: peripheral ID, size of register block
+- gpio-controller
+- #gpio-cells: 2
+
+Optional properties:
+- gpio-bank-name: name of bank (as default "pm8916_key" is used)
+
+
+Example:
+
+pmic_pon: pon at 800 {
+	compatible = "qcom,pm8916-pwrkey";
+	reg = <0x800 0x96>;
+	#gpio-cells = <2>;
+	gpio-controller;
+};
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index befb4af..7b4f0ed 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -60,6 +60,16 @@ config MSM_GPIO
 	  - APQ8016
 	  - MSM8916
 
+config PM8916_GPIO
+	bool "Qualcomm PM8916 PMIC GPIO/keypad driver"
+	depends on DM_GPIO && PMIC_PM8916
+	help
+	  Support for GPIO pins and power/reset buttons found on
+	  Qualcomm PM8916 PMIC.
+	  Default name for GPIO bank is "pm8916".
+	  Power and reset buttons are placed in "pm8916_key" bank and
+          have gpio numbers 0 and 1 respectively.
+
 config ROCKCHIP_GPIO
 	bool "Rockchip GPIO driver"
 	depends on DM_GPIO
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 830d7a6..fe06f8e 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -49,3 +49,4 @@ obj-$(CONFIG_VYBRID_GPIO)	+= vybrid_gpio.o
 obj-$(CONFIG_HIKEY_GPIO)	+= hi6220_gpio.o
 obj-$(CONFIG_PIC32_GPIO)	+= pic32_gpio.o
 obj-$(CONFIG_MSM_GPIO)		+= msm_gpio.o
+obj-$(CONFIG_PM8916_GPIO)	+= pm8916_gpio.o
diff --git a/drivers/gpio/pm8916_gpio.c b/drivers/gpio/pm8916_gpio.c
new file mode 100644
index 0000000..1abab7f
--- /dev/null
+++ b/drivers/gpio/pm8916_gpio.c
@@ -0,0 +1,302 @@
+/*
+ * Qualcomm pm8916 pmic gpio driver - part of Qualcomm PM8916 PMIC
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <power/pmic.h>
+#include <spmi/spmi.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <linux/bitops.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Register offset for each gpio */
+#define REG_OFFSET(x)          ((x) * 0x100)
+
+/* Register maps */
+
+/* Type and subtype are shared for all pm8916 peripherals */
+#define REG_TYPE               0x4
+#define REG_SUBTYPE            0x5
+
+#define REG_STATUS             0x08
+#define REG_STATUS_VAL_MASK    0x1
+
+/* MODE_CTL */
+#define REG_CTL           0x40
+#define REG_CTL_MODE_MASK       0x70
+#define REG_CTL_MODE_INPUT      0x00
+#define REG_CTL_MODE_INOUT      0x20
+#define REG_CTL_MODE_OUTPUT     0x10
+#define REG_CTL_OUTPUT_MASK     0x0F
+
+#define REG_DIG_VIN_CTL        0x41
+#define REG_DIG_VIN_VIN0       0
+
+#define REG_DIG_PULL_CTL       0x42
+#define REG_DIG_PULL_NO_PU     0x5
+
+#define REG_DIG_OUT_CTL        0x45
+#define REG_DIG_OUT_CTL_CMOS   (0x0 << 4)
+#define REG_DIG_OUT_CTL_DRIVE_L 0x1
+
+#define REG_EN_CTL             0x46
+#define REG_EN_CTL_ENABLE      (1 << 7)
+
+struct pm8916_gpio_bank {
+	uint16_t pid; /* Peripheral ID on SPMI bus */
+};
+
+static int pm8916_gpio_set_direction(struct udevice *dev, unsigned offset,
+				     bool input, int value)
+{
+	struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+	uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+	int ret;
+
+	/* Disable the GPIO */
+	ret = pmic_clrsetbits(dev->parent, gpio_base + REG_EN_CTL,
+			      REG_EN_CTL_ENABLE, 0);
+	if (ret < 0)
+		return ret;
+
+	/* Select the mode */
+	if (input)
+		ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL,
+				     REG_CTL_MODE_INPUT);
+	else
+		ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL,
+				     REG_CTL_MODE_INOUT | (value ? 1 : 0));
+	if (ret < 0)
+		return ret;
+
+	/* Set the right pull (no pull) */
+	ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_PULL_CTL,
+			     REG_DIG_PULL_NO_PU);
+	if (ret < 0)
+		return ret;
+
+	/* Configure output pin drivers if needed */
+	if (!input) {
+		/* Select the VIN - VIN0, pin is input so it doesn't matter */
+		ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_VIN_CTL,
+				     REG_DIG_VIN_VIN0);
+		if (ret < 0)
+			return ret;
+
+		/* Set the right dig out control */
+		ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_OUT_CTL,
+				     REG_DIG_OUT_CTL_CMOS |
+				     REG_DIG_OUT_CTL_DRIVE_L);
+		if (ret < 0)
+			return ret;
+	}
+
+	/* Enable the GPIO */
+	return pmic_clrsetbits(dev->parent, gpio_base + REG_EN_CTL, 0,
+			       REG_EN_CTL_ENABLE);
+}
+
+static int pm8916_gpio_direction_input(struct udevice *dev, unsigned offset)
+{
+	return pm8916_gpio_set_direction(dev, offset, true, 0);
+}
+
+static int pm8916_gpio_direction_output(struct udevice *dev, unsigned offset,
+					int value)
+{
+	return pm8916_gpio_set_direction(dev, offset, false, value);
+}
+
+static int pm8916_gpio_get_function(struct udevice *dev, unsigned offset)
+{
+	struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+	uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+	int reg;
+
+	/* Set the output value of the gpio */
+	reg = pmic_reg_read(dev->parent, gpio_base + REG_CTL);
+	if (reg < 0)
+		return reg;
+
+	switch (reg & REG_CTL_MODE_MASK) {
+	case REG_CTL_MODE_INPUT:
+		return GPIOF_INPUT;
+	case REG_CTL_MODE_INOUT: /* Fallthrough */
+	case REG_CTL_MODE_OUTPUT:
+		return GPIOF_OUTPUT;
+	default:
+		return GPIOF_UNKNOWN;
+	}
+}
+
+static int pm8916_gpio_get_value(struct udevice *dev, unsigned offset)
+{
+	struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+	uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+	int reg;
+
+	reg = pmic_reg_read(dev->parent, gpio_base + REG_STATUS);
+	if (reg < 0)
+		return reg;
+
+	return !!(reg & REG_STATUS_VAL_MASK);
+}
+
+static int pm8916_gpio_set_value(struct udevice *dev, unsigned offset,
+				 int value)
+{
+	struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+	uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
+
+	/* Set the output value of the gpio */
+	return pmic_clrsetbits(dev->parent, gpio_base + REG_CTL,
+			       REG_CTL_OUTPUT_MASK, !!value);
+}
+
+static const struct dm_gpio_ops pm8916_gpio_ops = {
+	.direction_input	= pm8916_gpio_direction_input,
+	.direction_output	= pm8916_gpio_direction_output,
+	.get_value		= pm8916_gpio_get_value,
+	.set_value		= pm8916_gpio_set_value,
+	.get_function		= pm8916_gpio_get_function,
+};
+
+static int pm8916_gpio_probe(struct udevice *dev)
+{
+	struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+	int reg;
+
+	priv->pid = dev_get_addr(dev);
+	if (priv->pid == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	/* Do a sanity check */
+	reg = pmic_reg_read(dev->parent, priv->pid + REG_TYPE);
+	if (reg != 0x10)
+		return -ENODEV;
+
+	reg = pmic_reg_read(dev->parent, priv->pid + REG_SUBTYPE);
+	if (reg != 0x5)
+		return -ENODEV;
+
+	return 0;
+}
+
+static int pm8916_gpio_ofdata_to_platdata(struct udevice *dev)
+{
+	struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+
+	uc_priv->gpio_count = fdtdec_get_int(gd->fdt_blob, dev->of_offset,
+					     "gpio-count", 0);
+	uc_priv->bank_name = fdt_getprop(gd->fdt_blob, dev->of_offset,
+					 "gpio-bank-name", NULL);
+	if (uc_priv->bank_name == NULL)
+		uc_priv->bank_name = "pm8916";
+
+	return 0;
+}
+
+static const struct udevice_id pm8916_gpio_ids[] = {
+	{ .compatible = "qcom,pm8916-gpio" },
+	{ }
+};
+
+U_BOOT_DRIVER(gpio_pm8916) = {
+	.name	= "gpio_pm8916",
+	.id	= UCLASS_GPIO,
+	.of_match = pm8916_gpio_ids,
+	.ofdata_to_platdata = pm8916_gpio_ofdata_to_platdata,
+	.probe	= pm8916_gpio_probe,
+	.ops	= &pm8916_gpio_ops,
+	.priv_auto_alloc_size = sizeof(struct pm8916_gpio_bank),
+};
+
+
+/* Add pmic buttons as GPIO as well - there is no generic way for now */
+#define PON_INT_RT_STS                        0x10
+#define KPDPWR_ON_INT_BIT                     0
+#define RESIN_ON_INT_BIT                      1
+
+static int pm8941_pwrkey_get_function(struct udevice *dev, unsigned offset)
+{
+	return GPIOF_INPUT;
+}
+
+static int pm8941_pwrkey_get_value(struct udevice *dev, unsigned offset)
+{
+	struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+
+	int reg = pmic_reg_read(dev->parent, priv->pid + PON_INT_RT_STS);
+
+	if (reg < 0)
+		return 0;
+
+	switch (offset) {
+	case 0: /* Power button */
+		return (reg & BIT(KPDPWR_ON_INT_BIT)) != 0;
+		break;
+	case 1: /* Reset button */
+	default:
+		return (reg & BIT(RESIN_ON_INT_BIT)) != 0;
+		break;
+	}
+}
+
+static const struct dm_gpio_ops pm8941_pwrkey_ops = {
+	.get_value		= pm8941_pwrkey_get_value,
+	.get_function		= pm8941_pwrkey_get_function,
+};
+
+static int pm8941_pwrkey_probe(struct udevice *dev)
+{
+	struct pm8916_gpio_bank *priv = dev_get_priv(dev);
+	int reg;
+
+	priv->pid = dev_get_addr(dev);
+	if (priv->pid == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	/* Do a sanity check */
+	reg = pmic_reg_read(dev->parent, priv->pid + REG_TYPE);
+	if (reg != 0x1)
+		return -ENODEV;
+
+	reg = pmic_reg_read(dev->parent, priv->pid + REG_SUBTYPE);
+	if (reg != 0x1)
+		return -ENODEV;
+
+	return 0;
+}
+
+static int pm8941_pwrkey_ofdata_to_platdata(struct udevice *dev)
+{
+	struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+
+	uc_priv->gpio_count = 2;
+	if (uc_priv->bank_name == NULL)
+		uc_priv->bank_name = "pm8916_key";
+
+	return 0;
+}
+
+static const struct udevice_id pm8941_pwrkey_ids[] = {
+	{ .compatible = "qcom,pm8916-pwrkey" },
+	{ }
+};
+
+U_BOOT_DRIVER(pwrkey_pm8941) = {
+	.name	= "pwrkey_pm8916",
+	.id	= UCLASS_GPIO,
+	.of_match = pm8941_pwrkey_ids,
+	.ofdata_to_platdata = pm8941_pwrkey_ofdata_to_platdata,
+	.probe	= pm8941_pwrkey_probe,
+	.ops	= &pm8941_pwrkey_ops,
+	.priv_auto_alloc_size = sizeof(struct pm8916_gpio_bank),
+};
-- 
2.5.0

[U-Boot] [PATCH v3 19/21] arm: Add support for Qualcomm Snapdragon family

[Mateusz Kulikowski]

First supported chip is APQ8016 (that is compatible with MSM8916).
Drivers in SoC code:
- Reset controller (PSHOLD)
- Clock controller (very simple clock configuration for MMC and UART)

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
---

Changes in v3: None
Changes in v2:
- Rename DM_SPMI -> SPMI
- Make MND divider comments more compact :)
- p -> priv
- Add reviewed-by
- Reordered Kconfig to keep alphabetical order
- Renamed reset_sandbox -> msm_reset (typo in reset.c)

Changes in v1:
- Fix include order
- Cleanup defines (added spaces for readibility)
- Base address is integer to avoid casting
- Use setbits_* family where possible
- Drop unneded comments, added newlines where needed
- Check return value of dev_get_addr
- Add binding for apq8016
- Cleaned up divider calculation
- Drop most of gpio.h (only empty file is needed)

 arch/arm/Kconfig                                   |  12 +
 arch/arm/Makefile                                  |   1 +
 arch/arm/mach-snapdragon/Kconfig                   |   6 +
 arch/arm/mach-snapdragon/Makefile                  |   8 +
 arch/arm/mach-snapdragon/clock-apq8016.c           | 262 +++++++++++++++++++++
 arch/arm/mach-snapdragon/include/mach/gpio.h       |   9 +
 .../mach-snapdragon/include/mach/sysmap-apq8016.h  |  14 ++
 arch/arm/mach-snapdragon/reset.c                   |  40 ++++
 8 files changed, 352 insertions(+)
 create mode 100644 arch/arm/mach-snapdragon/Kconfig
 create mode 100644 arch/arm/mach-snapdragon/Makefile
 create mode 100644 arch/arm/mach-snapdragon/clock-apq8016.c
 create mode 100644 arch/arm/mach-snapdragon/include/mach/gpio.h
 create mode 100644 arch/arm/mach-snapdragon/include/mach/sysmap-apq8016.h
 create mode 100644 arch/arm/mach-snapdragon/reset.c

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 6e5544f..2cb96e2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -504,6 +504,16 @@ config RMOBILE
 	bool "Renesas ARM SoCs"
 	select CPU_V7
 
+config ARCH_SNAPDRAGON
+	bool "Qualcomm Snapdragon SoCs"
+	select ARM64
+	select DM
+	select DM_GPIO
+	select DM_SERIAL
+	select SPMI
+	select OF_CONTROL
+	select OF_SEPARATE
+
 config ARCH_SOCFPGA
 	bool "Altera SOCFPGA family"
 	select CPU_V7
@@ -762,6 +772,8 @@ source "arch/arm/mach-rockchip/Kconfig"
 
 source "arch/arm/mach-s5pc1xx/Kconfig"
 
+source "arch/arm/mach-snapdragon/Kconfig"
+
 source "arch/arm/mach-socfpga/Kconfig"
 
 source "arch/arm/mach-stm32/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 6defdfb..bb2666c 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -54,6 +54,7 @@ machine-$(CONFIG_ARCH_MVEBU)		+= mvebu
 # TODO: rename CONFIG_ORION5X -> CONFIG_ARCH_ORION5X
 machine-$(CONFIG_ORION5X)		+= orion5x
 machine-$(CONFIG_ARCH_S5PC1XX)		+= s5pc1xx
+machine-$(CONFIG_ARCH_SNAPDRAGON)	+= snapdragon
 machine-$(CONFIG_ARCH_SOCFPGA)		+= socfpga
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_STM32)			+= stm32
diff --git a/arch/arm/mach-snapdragon/Kconfig b/arch/arm/mach-snapdragon/Kconfig
new file mode 100644
index 0000000..156e733
--- /dev/null
+++ b/arch/arm/mach-snapdragon/Kconfig
@@ -0,0 +1,6 @@
+if ARCH_SNAPDRAGON
+
+config SYS_SOC
+	default "snapdragon"
+
+endif
diff --git a/arch/arm/mach-snapdragon/Makefile b/arch/arm/mach-snapdragon/Makefile
new file mode 100644
index 0000000..8e84705
--- /dev/null
+++ b/arch/arm/mach-snapdragon/Makefile
@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += clock-apq8016.o
+obj-y += reset.o
diff --git a/arch/arm/mach-snapdragon/clock-apq8016.c b/arch/arm/mach-snapdragon/clock-apq8016.c
new file mode 100644
index 0000000..d548d75
--- /dev/null
+++ b/arch/arm/mach-snapdragon/clock-apq8016.c
@@ -0,0 +1,262 @@
+/*
+ * Clock drivers for Qualcomm APQ8016
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * Based on Little Kernel driver, simplified
+ *
+ * SPDX-License-Identifier:	BSD-3-Clause
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <dm.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <linux/bitops.h>
+
+/* GPLL0 clock control registers */
+#define GPLL0_STATUS        0x2101C
+#define GPLL0_STATUS_ACTIVE BIT(17)
+
+#define APCS_GPLL_ENA_VOTE  0x45000
+#define APCS_GPLL_ENA_VOTE_GPLL0 BIT(0)
+
+/* vote reg for blsp1 clock */
+#define APCS_CLOCK_BRANCH_ENA_VOTE  0x45004
+#define APCS_CLOCK_BRANCH_ENA_VOTE_BLSP1 BIT(10)
+
+/* SDC(n) clock control registers; n=1,2 */
+
+/* block control register */
+#define SDCC_BCR(n)                 ((n * 0x1000) + 0x41000)
+/* cmd */
+#define SDCC_CMD_RCGR(n)            ((n * 0x1000) + 0x41004)
+/* cfg */
+#define SDCC_CFG_RCGR(n)            ((n * 0x1000) + 0x41008)
+/* m */
+#define SDCC_M(n)                   ((n * 0x1000) + 0x4100C)
+/* n */
+#define SDCC_N(n)                   ((n * 0x1000) + 0x41010)
+/* d */
+#define SDCC_D(n)                   ((n * 0x1000) + 0x41014)
+/* branch control */
+#define SDCC_APPS_CBCR(n)           ((n * 0x1000) + 0x41018)
+#define SDCC_AHB_CBCR(n)            ((n * 0x1000) + 0x4101C)
+
+/* BLSP1 AHB clock (root clock for BLSP) */
+#define BLSP1_AHB_CBCR              0x1008
+
+/* Uart clock control registers */
+#define BLSP1_UART2_BCR             0x3028
+#define BLSP1_UART2_APPS_CBCR       0x302C
+#define BLSP1_UART2_APPS_CMD_RCGR   0x3034
+#define BLSP1_UART2_APPS_CFG_RCGR   0x3038
+#define BLSP1_UART2_APPS_M          0x303C
+#define BLSP1_UART2_APPS_N          0x3040
+#define BLSP1_UART2_APPS_D          0x3044
+
+/* CBCR register fields */
+#define CBCR_BRANCH_ENABLE_BIT  BIT(0)
+#define CBCR_BRANCH_OFF_BIT     BIT(31)
+
+struct msm_clk_priv {
+	phys_addr_t base;
+};
+
+/* Enable clock controlled by CBC soft macro */
+static void clk_enable_cbc(phys_addr_t cbcr)
+{
+	setbits_le32(cbcr, CBCR_BRANCH_ENABLE_BIT);
+
+	while (readl(cbcr) & CBCR_BRANCH_OFF_BIT)
+		;
+}
+
+/* clock has 800MHz */
+static void clk_enable_gpll0(phys_addr_t base)
+{
+	if (readl(base + GPLL0_STATUS) & GPLL0_STATUS_ACTIVE)
+		return; /* clock already enabled */
+
+	setbits_le32(base + APCS_GPLL_ENA_VOTE, APCS_GPLL_ENA_VOTE_GPLL0);
+
+	while ((readl(base + GPLL0_STATUS) & GPLL0_STATUS_ACTIVE) == 0)
+		;
+}
+
+#define APPS_CMD_RGCR_UPDATE BIT(0)
+
+/* Update clock command via CMD_RGCR */
+static void clk_bcr_update(phys_addr_t apps_cmd_rgcr)
+{
+	setbits_le32(apps_cmd_rgcr, APPS_CMD_RGCR_UPDATE);
+
+	/* Wait for frequency to be updated. */
+	while (readl(apps_cmd_rgcr) & APPS_CMD_RGCR_UPDATE)
+		;
+}
+
+struct bcr_regs {
+	uintptr_t cfg_rcgr;
+	uintptr_t cmd_rcgr;
+	uintptr_t M;
+	uintptr_t N;
+	uintptr_t D;
+};
+
+/* RCGR_CFG register fields */
+#define CFG_MODE_DUAL_EDGE (0x2 << 12) /* Counter mode */
+
+/* sources */
+#define CFG_CLK_SRC_CXO   (0 << 8)
+#define CFG_CLK_SRC_GPLL0 (1 << 8)
+#define CFG_CLK_SRC_MASK  (7 << 8)
+
+/* Mask for supported fields */
+#define CFG_MASK 0x3FFF
+
+#define CFG_DIVIDER_MASK 0x1F
+
+/* root set rate for clocks with half integer and MND divider */
+static void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
+				 int div, int m, int n, int source)
+{
+	uint32_t cfg;
+	/* M value for MND divider. */
+	uint32_t m_val = m;
+	/* NOT(N-M) value for MND divider. */
+	uint32_t n_val = ~((n)-(m)) * !!(n);
+	/* NOT 2D value for MND divider. */
+	uint32_t d_val = ~(n);
+
+	/* Program MND values */
+	writel(m_val, base + regs->M);
+	writel(n_val, base + regs->N);
+	writel(d_val, base + regs->D);
+
+	/* setup src select and divider */
+	cfg  = readl(base + regs->cfg_rcgr);
+	cfg &= ~CFG_MASK;
+	cfg |= source & CFG_CLK_SRC_MASK; /* Select clock source */
+
+	/* Set the divider; HW permits fraction dividers (+0.5), but
+	   for simplicity, we will support integers only */
+	if (div)
+		cfg |= (2 * div - 1) & CFG_DIVIDER_MASK;
+
+	if (n_val)
+		cfg |= CFG_MODE_DUAL_EDGE;
+
+	writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */
+
+	/* Inform h/w to start using the new config. */
+	clk_bcr_update(base + regs->cmd_rcgr);
+}
+
+static const struct bcr_regs sdc_regs[] = {
+	{
+	.cfg_rcgr = SDCC_CFG_RCGR(1),
+	.cmd_rcgr = SDCC_CMD_RCGR(1),
+	.M = SDCC_M(1),
+	.N = SDCC_N(1),
+	.D = SDCC_D(1),
+	},
+	{
+	.cfg_rcgr = SDCC_CFG_RCGR(2),
+	.cmd_rcgr = SDCC_CMD_RCGR(2),
+	.M = SDCC_M(2),
+	.N = SDCC_N(2),
+	.D = SDCC_D(2),
+	}
+};
+
+/* Init clock for SDHCI controller */
+static int clk_init_sdc(struct msm_clk_priv *priv, int slot, uint rate)
+{
+	int div = 8; /* 100MHz default */
+
+	if (rate == 200000000)
+		div = 4;
+
+	clk_enable_cbc(priv->base + SDCC_AHB_CBCR(slot));
+	/* 800Mhz/div, gpll0 */
+	clk_rcg_set_rate_mnd(priv->base, &sdc_regs[slot], div, 0, 0,
+			     CFG_CLK_SRC_GPLL0);
+	clk_enable_gpll0(priv->base);
+	clk_enable_cbc(priv->base + SDCC_APPS_CBCR(slot));
+
+	return rate;
+}
+
+static const struct bcr_regs uart2_regs = {
+	.cfg_rcgr = BLSP1_UART2_APPS_CFG_RCGR,
+	.cmd_rcgr = BLSP1_UART2_APPS_CMD_RCGR,
+	.M = BLSP1_UART2_APPS_M,
+	.N = BLSP1_UART2_APPS_N,
+	.D = BLSP1_UART2_APPS_D,
+};
+
+/* Init UART clock, 115200 */
+static int clk_init_uart(struct msm_clk_priv *priv)
+{
+	/* Enable iface clk */
+	clk_enable_cbc(priv->base + BLSP1_AHB_CBCR);
+	/* 7372800 uart block clock @ GPLL0 */
+	clk_rcg_set_rate_mnd(priv->base, &uart2_regs, 1, 144, 15625,
+			     CFG_CLK_SRC_GPLL0);
+	clk_enable_gpll0(priv->base);
+	/* Enable core clk */
+	clk_enable_cbc(priv->base + BLSP1_UART2_APPS_CBCR);
+
+	return 0;
+}
+
+ulong msm_set_periph_rate(struct udevice *dev, int periph, ulong rate)
+{
+	struct msm_clk_priv *priv = dev_get_priv(dev);
+
+	switch (periph) {
+	case 0: /* SDC1 */
+		return clk_init_sdc(priv, 0, rate);
+		break;
+	case 1: /* SDC2 */
+		return clk_init_sdc(priv, 1, rate);
+		break;
+	case 4: /* UART2 */
+		return clk_init_uart(priv);
+		break;
+	default:
+		return 0;
+	}
+}
+
+static int msm_clk_probe(struct udevice *dev)
+{
+	struct msm_clk_priv *priv = dev_get_priv(dev);
+
+	priv->base = dev_get_addr(dev);
+	if (priv->base == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	return 0;
+}
+
+static struct clk_ops msm_clk_ops = {
+	.set_periph_rate = msm_set_periph_rate,
+};
+
+static const struct udevice_id msm_clk_ids[] = {
+	{ .compatible = "qcom,gcc-msm8916" },
+	{ .compatible = "qcom,gcc-apq8016" },
+	{ }
+};
+
+U_BOOT_DRIVER(clk_msm) = {
+	.name		= "clk_msm",
+	.id		= UCLASS_CLK,
+	.of_match	= msm_clk_ids,
+	.ops		= &msm_clk_ops,
+	.priv_auto_alloc_size = sizeof(struct msm_clk_priv),
+	.probe		= msm_clk_probe,
+};
diff --git a/arch/arm/mach-snapdragon/include/mach/gpio.h b/arch/arm/mach-snapdragon/include/mach/gpio.h
new file mode 100644
index 0000000..ff949b2
--- /dev/null
+++ b/arch/arm/mach-snapdragon/include/mach/gpio.h
@@ -0,0 +1,9 @@
+/*
+ * Empty gpio.h
+ *
+ * This file must stay as arch/arm/include/asm/gpio.h requires it.
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
diff --git a/arch/arm/mach-snapdragon/include/mach/sysmap-apq8016.h b/arch/arm/mach-snapdragon/include/mach/sysmap-apq8016.h
new file mode 100644
index 0000000..cdbfad0
--- /dev/null
+++ b/arch/arm/mach-snapdragon/include/mach/sysmap-apq8016.h
@@ -0,0 +1,14 @@
+/*
+ * Qualcomm APQ8916 sysmap
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef _MACH_SYSMAP_APQ8016_H
+#define _MACH_SYSMAP_APQ8016_H
+
+#define GICD_BASE 0x0b000000
+#define GICC_BASE 0x0a20c000
+
+#endif
diff --git a/arch/arm/mach-snapdragon/reset.c b/arch/arm/mach-snapdragon/reset.c
new file mode 100644
index 0000000..2627eec
--- /dev/null
+++ b/arch/arm/mach-snapdragon/reset.c
@@ -0,0 +1,40 @@
+/*
+ * Qualcomm APQ8016 reset controller driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <reset.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int msm_reset_request(struct udevice *dev, enum reset_t type)
+{
+	phys_addr_t addr = dev_get_addr(dev);
+	if (!addr)
+		return -EINVAL;
+	writel(0, addr);
+	return -EINPROGRESS;
+}
+
+static struct reset_ops msm_reset_ops = {
+	.request	= msm_reset_request,
+};
+
+static const struct udevice_id msm_reset_ids[] = {
+	{ .compatible = "qcom,pshold" },
+	{ }
+};
+
+U_BOOT_DRIVER(msm_reset) = {
+	.name		= "msm_reset",
+	.id		= UCLASS_RESET,
+	.of_match	= msm_reset_ids,
+	.ops		= &msm_reset_ops,
+};
-- 
2.5.0

[U-Boot] [PATCH v3 20/21] board: Add Qualcomm Dragonboard 410C support

[Mateusz Kulikowski]

This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC

U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>

---

Changes in v3:
- readme: Added info on how to enter fastboot mode and that
  dtbTool is also part of skales. Added more explanation
  on image generation.
- head: Add comment why it's needed, drop MZ EFI signature
  that makes no sense on this particular SoC, fix confusing
  entry point name (+update .lds file)

Changes in v2:
- Renamed CONFIG_DM_SPMI -> CONFIG_SPMI
- Removed extra enter in dragonboard file
- Added ULPI* to defconfig
- Added MAINTAINERS to board
- Cleaned up config file - use distro defaults/environment:
  - Dropped multiple CONFIG_CMD* and other CONFIG_*
  - Added distro env/config
  - Dropped old boot commands
- Split dts - pm8916_gpio entries are taken directly from
  Linux Dragonboard dts; Add handles for u-boot in -uboot.dtsi;
  They will be removed once gpio drivers are converted to pinctrl.
- Renamed some pmic nodes, fixed dragonboard.c to find them properly.
- Added header and converted comments to c98-style in head.S
- Print error if pmic gpio node is not found.

Changes in v1:
- Add better help for dragonboard
- Move static structures to board_prepare_usb
- Add DM_SPMI to defconfig

 arch/arm/dts/Makefile                            |   2 +
 arch/arm/dts/dragonboard410c-uboot.dtsi          |  28 +++++
 arch/arm/dts/dragonboard410c.dts                 | 148 ++++++++++++++++++++++
 arch/arm/mach-snapdragon/Kconfig                 |  20 +++
 board/qualcomm/dragonboard410c/Kconfig           |  15 +++
 board/qualcomm/dragonboard410c/MAINTAINERS       |   6 +
 board/qualcomm/dragonboard410c/Makefile          |   8 ++
 board/qualcomm/dragonboard410c/dragonboard410c.c | 131 +++++++++++++++++++
 board/qualcomm/dragonboard410c/head.S            |  34 +++++
 board/qualcomm/dragonboard410c/readme.txt        |  71 +++++++++++
 board/qualcomm/dragonboard410c/u-boot.lds        |  90 +++++++++++++
 configs/dragonboard410c_defconfig                |  31 +++++
 include/configs/dragonboard410c.h                | 153 +++++++++++++++++++++++
 13 files changed, 737 insertions(+)
 create mode 100644 arch/arm/dts/dragonboard410c-uboot.dtsi
 create mode 100644 arch/arm/dts/dragonboard410c.dts
 create mode 100644 board/qualcomm/dragonboard410c/Kconfig
 create mode 100644 board/qualcomm/dragonboard410c/MAINTAINERS
 create mode 100644 board/qualcomm/dragonboard410c/Makefile
 create mode 100644 board/qualcomm/dragonboard410c/dragonboard410c.c
 create mode 100644 board/qualcomm/dragonboard410c/head.S
 create mode 100644 board/qualcomm/dragonboard410c/readme.txt
 create mode 100644 board/qualcomm/dragonboard410c/u-boot.lds
 create mode 100644 configs/dragonboard410c_defconfig
 create mode 100644 include/configs/dragonboard410c.h

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 578038b..3515bea 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -105,6 +105,8 @@ dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
 	fsl-ls1043a-qds-lpuart.dtb \
 	fsl-ls1043a-rdb.dtb
 
+dtb-$(CONFIG_ARCH_SNAPDRAGON) += dragonboard410c.dtb
+
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \
 	sun4i-a10-ba10-tvbox.dtb \
diff --git a/arch/arm/dts/dragonboard410c-uboot.dtsi b/arch/arm/dts/dragonboard410c-uboot.dtsi
new file mode 100644
index 0000000..cc2c175
--- /dev/null
+++ b/arch/arm/dts/dragonboard410c-uboot.dtsi
@@ -0,0 +1,28 @@
+/*
+ * U-Boot addition to handle Dragonboard 410c pins
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+&pm8916_gpios {
+	usb_hub_reset_pm {
+		gpios = <&pm8916_gpios 2 0>;
+	};
+
+	usb_sw_sel_pm {
+		gpios = <&pm8916_gpios 3 0>;
+	};
+};
+
+
+&pm8916_pon {
+	key_vol_down {
+		gpios = <&pm8916_pon 1 0>;
+	};
+
+	key_power {
+		gpios = <&pm8916_pon 0 0>;
+	};
+};
diff --git a/arch/arm/dts/dragonboard410c.dts b/arch/arm/dts/dragonboard410c.dts
new file mode 100644
index 0000000..7746622
--- /dev/null
+++ b/arch/arm/dts/dragonboard410c.dts
@@ -0,0 +1,148 @@
+/*
+ * Qualcomm APQ8016 based Dragonboard 410C board device tree source
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/dts-v1/;
+
+#include "skeleton64.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. Dragonboard 410c";
+	compatible = "qcom,dragonboard", "qcom,apq8016-sbc";
+	qcom,msm-id = <0xce 0x0 0xf8 0x0 0xf9 0x0 0xfa 0x0 0xf7 0x0>;
+	qcom,board-id = <0x10018 0x0>;
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x80000000 0 0x3da00000>;
+	};
+
+	chosen {
+		stdout-path = "/soc/serial at 78b0000";
+	};
+
+
+	soc {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		ranges = <0x0 0x0 0x0 0xffffffff>;
+		compatible = "simple-bus";
+
+		clkc: qcom,gcc at 1800000 {
+			compatible = "qcom,gcc-apq8016";
+			reg = <0x1800000 0x80000>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+		};
+
+		serial at 78b0000 {
+			compatible = "qcom,msm-uartdm-v1.4";
+			reg = <0x78b0000 0x200>;
+			u-boot,dm-pre-reloc;
+			clock = <&clkc 4>;
+		};
+
+		restart at 4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0x4ab000 0x4>;
+		};
+
+		soc_gpios: pinctrl at 1000000 {
+			compatible = "qcom,apq8016-pinctrl";
+			reg = <0x1000000 0x300000>;
+			gpio-controller;
+			gpio-count = <122>;
+			gpio-bank-name="soc";
+			#gpio-cells = <1>;
+		};
+
+		ehci at 78d9000 {
+			compatible = "qcom,ehci-host";
+			reg = <0x78d9000 0x400>;
+		};
+
+		sdhci at 07824000 {
+			compatible = "qcom,sdhci-msm-v4";
+			reg = <0x7824900 0x11c 0x7824000 0x800>;
+			bus-width = <0x8>;
+			index = <0x0>;
+			non-removable;
+			clock = <&clkc 0>;
+			clock-frequency = <100000000>;
+		};
+
+		sdhci at 07864000 {
+			compatible = "qcom,sdhci-msm-v4";
+			reg = <0x7864900 0x11c 0x7864000 0x800>;
+			index = <0x1>;
+			bus-width = <0x4>;
+			clock = <&clkc 1>;
+			clock-frequency = <200000000>;
+		};
+
+		spmi at 200f000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x200f800 0x200 0x2400000 0x400000 0x2c00000 0x400000>;
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			pmic0: pm8916 at 0 {
+				compatible = "qcom,spmi-pmic";
+				reg = <0x0 0x1>;
+				#address-cells = <0x1>;
+				#size-cells = <0x1>;
+
+				pm8916_pon: pm8916_pon at 800 {
+					compatible = "qcom,pm8916-pwrkey";
+					reg = <0x800 0x96>;
+					#gpio-cells = <2>;
+					gpio-controller;
+				};
+
+				pm8916_gpios: pm8916_gpios at c000 {
+					compatible = "qcom,pm8916-gpio";
+					reg = <0xc000 0x400>;
+					gpio-controller;
+					gpio-count = <4>;
+					#gpio-cells = <2>;
+					gpio-bank-name="pmic";
+				};
+			};
+
+			pmic1: pm8916 at 1 {
+				compatible = "qcom,spmi-pmic";
+				reg = <0x1 0x1>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		user1 {
+			label = "green:user1";
+			gpios = <&soc_gpios 21 0>;
+		};
+
+		user2 {
+			label = "green:user2";
+			gpios = <&soc_gpios 120 0>;
+		};
+
+		user3 {
+			label = "green:user3";
+			gpios = <&pm8916_gpios 0 0>;
+		};
+
+		user4 {
+			label = "green:user4";
+			gpios = <&pm8916_gpios 1 0>;
+		};
+	};
+};
+
+#include "dragonboard410c-uboot.dtsi"
diff --git a/arch/arm/mach-snapdragon/Kconfig b/arch/arm/mach-snapdragon/Kconfig
index 156e733..dc7ba21 100644
--- a/arch/arm/mach-snapdragon/Kconfig
+++ b/arch/arm/mach-snapdragon/Kconfig
@@ -3,4 +3,24 @@ if ARCH_SNAPDRAGON
 config SYS_SOC
 	default "snapdragon"
 
+choice
+	prompt "Snapdragon board select"
+
+config TARGET_DRAGONBOARD410C
+	bool "96Boards Dragonboard 410C"
+	help
+	  Support for 96Boards Dragonboard 410C. This board complies with
+	  96Board Open Platform Specifications. Features:
+	  - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
+	  - 1GiB RAM
+	  - 8GiB eMMC, uSD slot
+	  - WiFi, Bluetooth and GPS module
+	  - 2x Host, 1x Device USB port
+	  - HDMI
+	  - 20-pin low speed and 40-pin high speed expanders, 4 LED, 3 buttons
+
+endchoice
+
+source "board/qualcomm/dragonboard410c/Kconfig"
+
 endif
diff --git a/board/qualcomm/dragonboard410c/Kconfig b/board/qualcomm/dragonboard410c/Kconfig
new file mode 100644
index 0000000..03bd7ae
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_DRAGONBOARD410C
+
+config SYS_BOARD
+	default "dragonboard410c"
+
+config SYS_VENDOR
+	default "qualcomm"
+
+config SYS_SOC
+	default "apq8016"
+
+config SYS_CONFIG_NAME
+	default "dragonboard410c"
+
+endif
diff --git a/board/qualcomm/dragonboard410c/MAINTAINERS b/board/qualcomm/dragonboard410c/MAINTAINERS
new file mode 100644
index 0000000..65cb47c
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/MAINTAINERS
@@ -0,0 +1,6 @@
+DRAGONBOARD410C BOARD
+M:	Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+S:	Maintained
+F:	board/qualcomm/dragonboard410c/
+F:	include/configs/dragonboard410c.h
+F:	configs/dragonboard410c_defconfig
diff --git a/board/qualcomm/dragonboard410c/Makefile b/board/qualcomm/dragonboard410c/Makefile
new file mode 100644
index 0000000..cd67808
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/Makefile
@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= dragonboard410c.o
+extra-y += head.o
diff --git a/board/qualcomm/dragonboard410c/dragonboard410c.c b/board/qualcomm/dragonboard410c/dragonboard410c.c
new file mode 100644
index 0000000..1fa5664
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/dragonboard410c.c
@@ -0,0 +1,131 @@
+/*
+ * Board init file for Dragonboard 410C
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <usb.h>
+#include <asm/gpio.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_1_SIZE;
+	return 0;
+}
+
+void dram_init_banksize(void)
+{
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+}
+
+
+int board_prepare_usb(enum usb_init_type type)
+{
+	static struct udevice *pmic_gpio;
+	static struct gpio_desc hub_reset, usb_sel;
+	int ret = 0, node;
+
+	if (!pmic_gpio) {
+		ret = uclass_get_device_by_name(UCLASS_GPIO,
+						"pm8916_gpios at c000",
+						&pmic_gpio);
+		if (ret < 0) {
+			printf("Failed to find pm8916_gpios@c000 node.\n");
+			return ret;
+		}
+	}
+
+	/* Try to request gpios needed to start usb host on dragonboard */
+	if (!dm_gpio_is_valid(&hub_reset)) {
+		node = fdt_subnode_offset(gd->fdt_blob, pmic_gpio->of_offset,
+					  "usb_hub_reset_pm");
+		if (node < 0) {
+			printf("Failed to find usb_hub_reset_pm dt node.\n");
+			return node;
+		}
+		ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0,
+						 &hub_reset, 0);
+		if (ret < 0) {
+			printf("Failed to request usb_hub_reset_pm gpio.\n");
+			return ret;
+		}
+	}
+
+	if (!dm_gpio_is_valid(&usb_sel)) {
+		node = fdt_subnode_offset(gd->fdt_blob, pmic_gpio->of_offset,
+					  "usb_sw_sel_pm");
+		if (node < 0) {
+			printf("Failed to find usb_sw_sel_pm dt node.\n");
+			return 0;
+		}
+		ret = gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0,
+						 &usb_sel, 0);
+		if (ret < 0) {
+			printf("Failed to request usb_sw_sel_pm gpio.\n");
+			return ret;
+		}
+	}
+
+	if (type == USB_INIT_HOST) {
+		/* Start USB Hub */
+		dm_gpio_set_dir_flags(&hub_reset,
+				      GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+		mdelay(100);
+		/* Switch usb to host connectors */
+		dm_gpio_set_dir_flags(&usb_sel,
+				      GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+		mdelay(100);
+	} else { /* Device */
+		/* Disable hub */
+		dm_gpio_set_dir_flags(&hub_reset, GPIOD_IS_OUT);
+		/* Switch back to device connector */
+		dm_gpio_set_dir_flags(&usb_sel, GPIOD_IS_OUT);
+	}
+
+	return 0;
+}
+
+int board_init(void)
+{
+	return 0;
+}
+
+/* Check for vol- button - if pressed - stop autoboot */
+int misc_init_r(void)
+{
+	struct udevice *pon;
+	struct gpio_desc resin;
+	int node, ret;
+
+	ret = uclass_get_device_by_name(UCLASS_GPIO, "pm8916_pon@800", &pon);
+	if (ret < 0) {
+		printf("Failed to find PMIC pon node. Check device tree\n");
+		return 0;
+	}
+
+	node = fdt_subnode_offset(gd->fdt_blob, pon->of_offset, "key_vol_down");
+	if (node < 0) {
+		printf("Failed to find key_vol_down node. Check device tree\n");
+		return 0;
+	}
+
+	if (gpio_request_by_name_nodev(gd->fdt_blob, node, "gpios", 0, &resin,
+				       0)) {
+		printf("Failed to request key_vol_down button.\n");
+		return 0;
+	}
+
+	if (dm_gpio_get_value(&resin)) {
+		setenv("bootdelay", "-1");
+		printf("Power button pressed - dropping to console.\n");
+	}
+
+	return 0;
+}
diff --git a/board/qualcomm/dragonboard410c/head.S b/board/qualcomm/dragonboard410c/head.S
new file mode 100644
index 0000000..ba29b12
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/head.S
@@ -0,0 +1,34 @@
+/*
+ * ARM64 header for proper chain-loading with Little Kernel.
+ *
+ * Little Kernel shipped with Dragonboard410C boots standard Linux images for
+ * ARM64. This file adds header that is required to boot U-Boot properly.
+ *
+ * For details see:
+ * https://www.kernel.org/doc/Documentation/arm64/booting.txt
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <config.h>
+
+.global _arm64_header
+_arm64_header:
+	b _start
+	.word 0
+	/* Image load offset from start of RAM, little-endian */
+	.quad   CONFIG_SYS_TEXT_BASE-PHYS_SDRAM_1
+	/* Effective size of kernel image, little-endian */
+	.quad   0 /* 0x60000 - ignored */
+	/* Informative flags, little-endian */
+	.quad   0
+	.quad   0                               /* reserved */
+	.quad   0                               /* reserved */
+	.quad   0                               /* reserved */
+	.byte   0x41                            /* Magic number, "ARM\x64" */
+	.byte   0x52
+	.byte   0x4d
+	.byte   0x64
+	.word   0                               /* reserved */
diff --git a/board/qualcomm/dragonboard410c/readme.txt b/board/qualcomm/dragonboard410c/readme.txt
new file mode 100644
index 0000000..7fc7c7a
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/readme.txt
@@ -0,0 +1,71 @@
+#
+# (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+Build & Run instructions:
+
+1) Install mkbootimg and dtbTool from
+   git://codeaurora.org/quic/kernel/skales (15ece94f09 worked for me)
+2) Setup CROSS_COMPILE to aarch64 compiler
+3) make dragonboard410c_config
+4) make
+5) generate fake, empty ramdisk (can have 0 bytes)
+$ touch rd
+
+6) Generate qualcomm device tree table with dtbTool [1]
+$ dtbTool -o dt.img arch/arm/dts
+
+7) Generate Android boot image with mkbootimg [2]:
+$ mkbootimg --kernel=u-boot-dtb.bin --output=u-boot.img --dt=dt.img  \
+  --pagesize 2048 --base 0x80000000 --ramdisk=rd --cmdline=""
+
+8) Enter fastboot (reboot board with vol- button pressed)
+
+9) Boot it:
+$ fastboot boot u-boot.img
+or flash as kernel:
+$ fastboot flash boot u-boot.img
+$ fastboot reboot
+
+
+What is working:
+- UART
+- GPIO (SoC)
+- SD
+- eMMC
+- Reset
+- USB in EHCI mode (usb starts does switch device->host, usb stop does the opposite)
+- PMIC GPIOS (but not in generic subsystem)
+- PMIC "special" buttons (power, vol-)
+
+What is not working / known bugs:
+- SDHCI is slow (~2.5MiB/s for SD and eMMC)
+
+[1] To boot any kernel image, Little Kernel requires valid device tree for the
+platform it runs on. dtbTool creates device tree table that Little Kernel scans.
+Later on proper device tree is passed to next boot stage.
+Full device tree is not required to boot u-boot. Enough would be:
+/dts-v1/;
+
+/ {
+	model = "Qualcomm Technologies, Inc. Dragonboard 410c";
+	compatible = "qcom,dragonboard", "qcom,apq8016-sbc";
+	qcom,msm-id = <0xce 0x0 0xf8 0x0 0xf9 0x0 0xfa 0x0 0xf7 0x0>;
+	qcom,board-id = <0x10018 0x0>;
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+	chosen { };
+	aliases { };
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x80000000 0 0x3da00000>;
+	};
+};
+
+but for simplicity (and because size of image is not that critical) we use
+existing Qualcomm device trees.
+
+[2] Note that ramdisk is required, even if it is unused.
diff --git a/board/qualcomm/dragonboard410c/u-boot.lds b/board/qualcomm/dragonboard410c/u-boot.lds
new file mode 100644
index 0000000..6e1c5a8
--- /dev/null
+++ b/board/qualcomm/dragonboard410c/u-boot.lds
@@ -0,0 +1,90 @@
+/*
+ * Override linker script for fastboot-readable images
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * Based on arch/arm/cpu/armv8/u-boot.lds (Just add header)
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+OUTPUT_FORMAT("elf64-littleaarch64", "elf64-littleaarch64", "elf64-littleaarch64")
+OUTPUT_ARCH(aarch64)
+ENTRY(_arm64_header)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(8);
+	.text :
+	{
+		*(.__image_copy_start)
+		board/qualcomm/dragonboard410c/head.o (.text*)
+		CPUDIR/start.o (.text*)
+		*(.text*)
+	}
+
+	. = ALIGN(8);
+	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+	. = ALIGN(8);
+	.data : {
+		*(.data*)
+	}
+
+	. = ALIGN(8);
+
+	. = .;
+
+	. = ALIGN(8);
+	.u_boot_list : {
+		KEEP(*(SORT(.u_boot_list*)));
+	}
+
+	. = ALIGN(8);
+
+	.image_copy_end :
+	{
+		*(.__image_copy_end)
+	}
+
+	. = ALIGN(8);
+
+	.rel_dyn_start :
+	{
+		*(.__rel_dyn_start)
+	}
+
+	.rela.dyn : {
+		*(.rela*)
+	}
+
+	.rel_dyn_end :
+	{
+		*(.__rel_dyn_end)
+	}
+
+	_end = .;
+
+	. = ALIGN(8);
+
+	.bss_start : {
+		KEEP(*(.__bss_start));
+	}
+
+	.bss : {
+		*(.bss*)
+		 . = ALIGN(8);
+	}
+
+	.bss_end : {
+		KEEP(*(.__bss_end));
+	}
+
+	/DISCARD/ : { *(.dynsym) }
+	/DISCARD/ : { *(.dynstr*) }
+	/DISCARD/ : { *(.dynamic*) }
+	/DISCARD/ : { *(.plt*) }
+	/DISCARD/ : { *(.interp*) }
+	/DISCARD/ : { *(.gnu*) }
+}
diff --git a/configs/dragonboard410c_defconfig b/configs/dragonboard410c_defconfig
new file mode 100644
index 0000000..84fe597
--- /dev/null
+++ b/configs/dragonboard410c_defconfig
@@ -0,0 +1,31 @@
+CONFIG_ARM=y
+CONFIG_ARM64=y
+CONFIG_ARCH_SNAPDRAGON=y
+CONFIG_TARGET_DRAGONBOARD410C=y
+
+CONFIG_SYS_PROMPT="dragonboard410c => "
+CONFIG_CMD_USB=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_IMLS is not set
+CONFIG_DEFAULT_DEVICE_TREE="dragonboard410c"
+
+CONFIG_CLK=y
+CONFIG_MSM_GPIO=y
+CONFIG_PM8916_GPIO=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_RESET=y
+CONFIG_DM_MMC=y
+CONFIG_MSM_SDHCI=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_PM8916=y
+CONFIG_SPMI=y
+CONFIG_SPMI_MSM=y
+CONFIG_MSM_SERIAL=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_MSM=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_STORAGE=y
diff --git a/include/configs/dragonboard410c.h b/include/configs/dragonboard410c.h
new file mode 100644
index 0000000..1dfb171
--- /dev/null
+++ b/include/configs/dragonboard410c.h
@@ -0,0 +1,153 @@
+/*
+ * Board configuration file for Dragonboard 410C
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIGS_DRAGONBOARD410C_H
+#define __CONFIGS_DRAGONBOARD410C_H
+
+#include <linux/sizes.h>
+#include <asm/arch/sysmap-apq8016.h>
+
+#define CONFIG_IDENT_STRING		"\nQualcomm-DragonBoard 410C"
+
+#define CONFIG_MISC_INIT_R /* To stop autoboot */
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_LIBFDT
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM_1			0x80000000
+/* 1008 MB (the last ~30Mb are secured for TrustZone by ATF*/
+#define PHYS_SDRAM_1_SIZE		0x3da00000
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_TEXT_BASE		0x80080000
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x7fff0)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x80000)
+#define CONFIG_SYS_BOOTM_LEN		0x1000000 /* 16MB max kernel size */
+
+/* UART */
+#define CONFIG_BAUDRATE			115200
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY		19000000
+
+/* This are needed to have proper mmc support */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SDHCI
+
+#define CONFIG_SYS_LDSCRIPT "board/qualcomm/dragonboard410c/u-boot.lds"
+
+/* Fixup - in init code we switch from device to host mode,
+ * it has to be done after each HCD reset */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+
+#define CONFIG_USB_HOST_ETHER /* Enable USB Networking */
+
+/* Support all possible USB ethernet dongles */
+#define CONFIG_USB_ETHER_DM9601
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_ASIX88179
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_SMSC95XX
+
+/* Libraries  */
+#define CONFIG_MD5
+
+/* Extra Commands */
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_GPIO
+#define CONFIG_CMD_GPT
+#define CONFIG_CMD_MD5SUM
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MMC
+/* Enable that for switching of boot partitions */
+/* Disabled by default as some sub-commands can brick eMMC */
+/*#define CONFIG_SUPPORT_EMMC_BOOT */
+#define CONFIG_CMD_PART
+#define CONFIG_CMD_REGINFO	/* Register dump		*/
+#define CONFIG_CMD_TFTP
+#define CONFIG_CMD_TIMER
+#define CONFIG_CMD_UNZIP
+
+/* Partition table support */
+#define HAVE_BLOCK_DEVICE /* Needed for partition commands */
+#define CONFIG_PARTITION_UUIDS
+
+#include <config_distro_defaults.h>
+
+/* BOOTP options */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+/* Environment - Boot*/
+#define CONFIG_BOOTARGS "console=ttyMSM0,115200n8"
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(USB, usb, 0) \
+	func(MMC, mmc, 0) \
+	func(MMC, mmc, 1) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+/* Does what recovery does */
+#define REFLASH(file, part) \
+"part start mmc 0 "#part" start && "\
+"part size mmc 0 "#part" size && "\
+"tftp $loadaddr "#file" && " \
+"mmc write $loadaddr $start $size && "
+
+
+#define CONFIG_ENV_REFLASH \
+"mmc dev 0 && "\
+"usb start && "\
+"dhcp && "\
+"tftp $loadaddr dragonboard/rescue/gpt_both0.bin && "\
+"mmc write $loadaddr 0 43 && " \
+"mmc rescan && "\
+REFLASH(dragonboard/rescue/NON-HLOS.bin, 1)\
+REFLASH(dragonboard/rescue/sbl1.mbn, 2)\
+REFLASH(dragonboard/rescue/rpm.mbn, 3)\
+REFLASH(dragonboard/rescue/tz.mbn, 4)\
+REFLASH(dragonboard/rescue/hyp.mbn, 5)\
+REFLASH(dragonboard/rescue/sec.dat, 6)\
+REFLASH(dragonboard/rescue/emmc_appsboot.mbn, 7)\
+REFLASH(dragonboard/u-boot.img, 8)\
+"usb stop &&"\
+"echo Reflash completed"
+
+/* Environment */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"reflash="CONFIG_ENV_REFLASH"\0"\
+	"loadaddr=0x81000000\0" \
+	"fdt_high=0xffffffffffffffff\0" \
+	"initrd_high=0xffffffffffffffff\0" \
+	"linux_image=Image\0" \
+	"linux_addr=0x81000000\0"\
+	"fdt_image=apq8016-sbc.dtb\0" \
+	"fdt_addr=0x83000000\0"\
+	"ramdisk_addr=0x84000000\0"\
+	BOOTENV
+
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE			0x1000
+#define CONFIG_ENV_VARS_UBOOT_CONFIG
+#define CONFIG_SYS_NO_FLASH
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + SZ_8M)
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_MAXARGS		64	/* max command args */
+
+#endif
-- 
2.5.0

[U-Boot] [PATCH v3 21/21] Add myself as Snapdragon and SPMI maintainer

[Mateusz Kulikowski]

- Update MAINTAINERS
- Update git-mailrc

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

---

Changes in v3: None
Changes in v2:
- New patch

Changes in v1: None

 MAINTAINERS    | 11 +++++++++++
 doc/git-mailrc |  3 +++
 2 files changed, 14 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 9d447ea..93c6c72 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -125,6 +125,11 @@ F:	arch/arm/mach-s5pc1xx/
 F:	arch/arm/cpu/armv7/s5p-common/
 F:	arch/arm/include/asm/arch-s3c24x0/
 
+ARM SNAPDRAGON
+M:	Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+S:	Maintained
+F:	arch/arm/mach-snapdragon/
+
 ARM STM SPEAR
 #M:	Vipin Kumar <vipin.kumar@st.com>
 S:	Orphaned (Since 2016-02)
@@ -389,6 +394,12 @@ F:	drivers/mtd/spi/
 F:	drivers/spi/
 F:	include/spi*
 
+SPMI
+M:	Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+S:	Maintained
+F:	drivers/spmi/
+F:	include/spmi/
+
 TQ GROUP
 #M:	Martin Krause <martin.krause@tq-systems.de>
 S:	Orphaned (Since 2016-02)
diff --git a/doc/git-mailrc b/doc/git-mailrc
index ced7085..1201d4a 100644
--- a/doc/git-mailrc
+++ b/doc/git-mailrc
@@ -33,6 +33,7 @@ alias lukma          Lukasz Majewski <l.majewski@samsung.com>
 alias macpaul        Macpaul Lin <macpaul@andestech.com>
 alias marex          Marek Vasut <marex@denx.de>
 alias masahiro       Masahiro Yamada <yamada.masahiro@socionext.com>
+alias mateusz        Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
 alias monstr         Michal Simek <monstr@monstr.eu>
 alias panto          Pantelis Antoniou <panto@antoniou-consulting.com>
 alias prafulla       Prafulla Wadaskar <prafulla@marvell.com>
@@ -67,6 +68,7 @@ alias rmobile        uboot, iwamatsu
 alias s3c            samsung
 alias s5pc           samsung
 alias samsung        uboot, prom
+alias snapdragon     uboot, mateusz
 alias socfpga        uboot, marex, Dinh Nguyen <dinguyen@opensource.altera.com>
 alias sunxi          uboot, ijc, jwrdegoede
 alias tegra          uboot, sjg, Tom Warren <twarren@nvidia.com>, Stephen Warren <swarren@nvidia.com>
@@ -127,6 +129,7 @@ alias nand           uboot, scottwood
 alias net            uboot, jhersh
 alias phy            uboot, jhersh
 alias spi            uboot, jagan
+alias spmi           uboot, mateusz
 alias ubi            uboot, hs
 alias usb            uboot, marex
 alias video          uboot, ag
-- 
2.5.0

[U-Boot] [PATCH v3 05/21] usb: ulpi: Add Kconfig options for ULPI

[Marek Vasut]

On 03/13/2016 10:36 PM, Mateusz Kulikowski wrote:
> The following options can be now enabled via defconfig:
> - CONFIG_USB_ULPI
> - CONFIG_USB_ULPI_VIEWPORT
> - CONFIG_USB_ULPI_VIEWPORT_OMAP
> 
> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
> Reviewed-by: Simon Glass <sjg@chromium.org>

Acked-by: Marek Vasut <marex@denx.de>
Best regards,
Marek Vasut

[U-Boot] [PATCH v3 07/21] usb: ulpi: Fix viewport_addr type

[Marek Vasut]

On 03/13/2016 10:36 PM, Mateusz Kulikowski wrote:
> viewport_addr is address of memory mapped ULPI viewport.
> It is used only as argument to readl/writel later
> causing compile warnings on 64-bit devices.
> 
> This fix changes its type to match pointer size.
> 
> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>

Acked-by: Marek Vasut <marex@denx.de>

Best regards,
Marek Vasut

[U-Boot] [PATCH v3 08/21] usb: ulpi: Fix compile warning in read/write on 64-bit machines.

[Marek Vasut]

On 03/13/2016 10:36 PM, Mateusz Kulikowski wrote:
> ulpi_read and ulpi_write are used to read/write registers via ULPI bus.
> Code generates compilation warnings on 64-bit machines where pointer
> is cast to u32.
> 
> This patch drops all but last 8 bits of register address.
> It is possible, because addresses on ULPI bus are 6- or 8-bit.
> 
> It is not possible (according to ULPI 1.1 spec) to have more
> than 8-bit addressing.
> 
> This patch should not cause regressions as all calls to
> ulpi_read/write use either structure pointer (@ address 0) or integer
> offsets cast to pointer - addresses requested are way below 8-bit range.
> 
> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>

Acked-by: Marek Vasut <marex@denx.de>

-- 
Best regards,
Marek Vasut

[U-Boot] [PATCH v3 09/21] eth: asix88179: Print packet length properly

[Marek Vasut]

On 03/13/2016 10:36 PM, Mateusz Kulikowski wrote:
> Debug printf used '%u' to print size_t variable.
> This caused warnings on 64-bit machines.
> 
> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>

Acked-by: Marek Vasut <marex@denx.de>

Best regards,
Marek Vasut

[U-Boot] [PATCH v3 09/21] eth: asix88179: Print packet length properly

[Joe Hershberger]

On Sun, Mar 13, 2016 at 4:36 PM, Mateusz Kulikowski
<mateusz.kulikowski@gmail.com> wrote:
> Debug printf used '%u' to print size_t variable.
> This caused warnings on 64-bit machines.
>
> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>

Acked-by: Joe Hershberger <joe.hershberger@ni.com>

[U-Boot] [U-Boot,v3,10/21] usb: Rename ehci-fsl.h to ehci-ci.h

[Tom Rini]

On Sun, Mar 13, 2016 at 10:36:33PM +0100, Mateusz Kulikowski wrote:

> Most of ehci-fsl header describe USB controller
> designed by Chipidea and used by various SoC vendors.
> 
> This patch renames it to a generic header: ehci-ci.h
> Contents of file are not changed (so it contains several
> references to freescale SoCs).
> 
> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
> Acked-by: Marek Vasut <marex@denx.de>
> Tested-by: Simon Glass <sjg@chromium.org>

This misses about 10 files, easily found with a 'git grep -l
usb/ehci-fsl.h', please respin, thanks.

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20160327/b2a052c8/attachment.sig>

[U-Boot] [U-Boot, v3, 20/21] board: Add Qualcomm Dragonboard 410C support

[Tom Rini]

On Sun, Mar 13, 2016 at 10:36:43PM +0100, Mateusz Kulikowski wrote:

> This commit add support for 96Boards Dragonboard410C.
> It is board based on APQ8016 Qualcomm SoC, complying with
> 96boards specification.
> Features (present out of the box):
> - 4x Cortex A53 (ARMv8)
> - 2x USB Host port
> - 1x USB Device port
> - 4x LEDs
> - 1x HDMI connector
> - 1x uSD connector
> - 3x buttons (Power, Vol+, Vol-/Reset)
> - WIFI, Bluetooth with integrated antenna
> - 8GiB eMMC
> 
> U-Boot boots chained with fastboot in 64-bit mode.
> For detailed build instructions see readme.txt in board directory.
> 
> Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
> Tested-by: Simon Glass <sjg@chromium.org>

Two problems.  One, OF_LIBFDT has moved to Kconfig, please update the
defconfig _and_ re-run savedefconfig.  Two, the MMU code has updated and
you need to provide a mem_map.  This shouldn't be hard, but I don't have
the hardware and can't test a patch.  Thanks!

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20160327/be9b0bd9/attachment.sig>