[U-Boot] Newbie SPL question for socfpga_sockit

[Marek Vasut <marex@denx.de>]

On 03/16/2016 05:17 PM, George Broz wrote:
> On 15 March 2016 at 18:29, George Broz <brozgeo@gmail.com> wrote:
> 
>>
>> Hello again -
>>
>> So under the assumption my SoCKit h/w was broken, I bought a new board.
>> They are back ordered on SoCKit boards, so I got a DE0-Nano-SoC instead.
>>
>> I build the v2016.03 (release) version of u-boot-with-spl.sfp.
>>
>> I power-up the (brand new) board and get:
>>
>> U-Boot SPL 2016.03 (Mar 15 2016 - 14:52:42)
>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
>> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED
>> drivers/ddr/altera/sequencer.c: Calibration complete
>> SDRAM calibration failed.
>> ### ERROR ### Please RESET the board ###
>>
>> U-Boot SPL 2016.03 (Mar 15 2016 - 14:52:42)
>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
>> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED
>> drivers/ddr/altera/sequencer.c: Calibration complete
>> SDRAM calibration failed.
>> ### ERROR ### Please RESET the board ###
>>
>> U-Boot SPL 2016.03 (Mar 15 2016 - 14:52:42)
>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
>> drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
>> drivers/ddr/altera/sequencer.c: Calibration complete
>> Trying to boot from MMC
>>
>> U-Boot 2016.03 (Mar 15 2016 - 14:52:42 -0700)
>>
>> CPU:   Altera SoCFPGA Platform
>> FPGA:  Altera Cyclone V, SE/A4 or SX/C4, version 0x0
>> BOOT:  SD/MMC Internal Transceiver (3.0V)
>>        Watchdog enabled
>> I2C:   ready
>> DRAM:  1 GiB
>> MMC:   dwmmc0 at ff704000: 0
>> In:    serial
>> Out:   serial
>> Err:   serial
>> Model: Terasic DE0-Nano(Atlas)
>> Net:
>> Error: ethernet at ff702000 address not set.
>> No ethernet found.
>> Hit any key to stop autoboot:  0
>> =>
>>
>> And this is a good case... usually it doesn't succeed after the fourth try
>> and I have to cycle power 4 or 5 times before I get lucky.
>>
>> If I do get lucky and then try to see a USB storage device, then I get:
>>
>> =>
>> => usb start
>> starting USB...
>> USB0:   Core Release: 2.93a
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> dwc_otg_core_host_init: Timeout!
>> scanning bus 0 for devices... 1 USB Device(s) found
>> =>
>>
>> (Every time)
>>
>> The version of u-boot SPL that ships with the board:
>> U-Boot SPL 2013.01.01 (Dec 29 2014 - 15:29:15)
>>
>> boots every time and has limited USB capability as
>> it can see some USB sticks, but not others.
>>
>>
>> Anyway - brand new board - same old symptoms.
>>
>> Is it perhaps a toolchain problem?? I'm using:
>>
>> Thread model: posix
>> gcc version 4.9.3 20141031 (prerelease) (Linaro GCC 4.9-2014.11)
>>
>> COLLECT_GCC=arm-poky-linux-gnueabi-gcc
>> COLLECT_LTO_WRAPPER=/opt/poky/1.7.1/sysroots/x86_64-pokysdk-linux/usr/libexec/arm-poky-linux-gnueabi/gcc/arm-poky-linux-gnueabi/4.9.3/lto-wrapper
>> < snip >
>>
>> Any advice greatly appreciated.
>>
>>
>> Regards,
>> --George Broz
> 
> Rebuilt using the Altera EDS15.0 toolchain:
> 
>   arm-altera-eabi-gcc --version
>   arm-altera-eabi-gcc (Sourcery CodeBench Lite 2014.11-13) 4.9.1
>   Copyright (C) 2014 Free Software Foundation, Inc.
>   This is free software; see the source for copying conditions.  There is NO
>   warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
> 
> 
> Get same result ... mostly failing calibration, non-working USB....
> 
> U-Boot SPL 2016.03 (Mar 16 2016 - 08:27:20)
> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED
> drivers/ddr/altera/sequencer.c: Calibration complete
> SDRAM calibration failed.
> ### ERROR ### Please RESET the board ###
> 
> U-Boot SPL 2016.03 (Mar 16 2016 - 08:27:20)
> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED
> drivers/ddr/altera/sequencer.c: Calibration complete
> SDRAM calibration failed.
> ### ERROR ### Please RESET the board ###
> 
> U-Boot SPL 2016.03 (Mar 16 2016 - 08:27:20)
> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration
> drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
> drivers/ddr/altera/sequencer.c: Calibration complete
> Trying to boot from MMC
> 
> 
> U-Boot 2016.03 (Mar 16 2016 - 08:27:20 -0700)
> 
> Does this work for anybody else?
> Is it in anyone's experience that these (cheaper) Terasic
> eval boards are generally out of spec?
> 
> Is there a way to relax the calibration parameters? the USB parameters?
> 
> Would it help if I posted debug output?

Sorry for the late reply, I am horribly overloaded now. I asked someone
in #u-boot who has the DE0-NANO-SOC board to test latest u-boot/master
on it and it apparently worked for him. I should get some more feedback
in the morning [ see http://pastebin.com/CM1QJGnh ] .

Still, this is getting real creepy. You are the second person who is
complaining about misbehavior of terasic boards with mainline u-boot
and whatever I do, I cannot replicate this.

I am at least CCing the Altera guys. Sorry I have no better suggestion
for you :(

Best regards,
Marek Vasut