[U-Boot] [uboot] [PATCH 2/2] net: phy: ti: Allow the driver to be more configurable

[Dan Murphy <dmurphy@ti.com>]

On 04/05/2016 12:36 PM, Michal Simek wrote:
> On 5.4.2016 19:18, Dan Murphy wrote:
>> Michal
>>
>> On 04/05/2016 12:01 PM, Michal Simek wrote:
>>> On 5.4.2016 17:05, Dan Murphy wrote:
>>>> Not all devices use the same internal delay or fifo depth.
>>>> Add the ability to set the internal delay for rx or tx and the
>>>> fifo depth via the devicetree.  If the value is not set in the
>>>> devicetree then set the delay to the default.
>>>>
>>>> If devicetree is not used then use the default defines within the
>>>> driver.
>>>>
>>>> Signed-off-by: Dan Murphy <dmurphy@ti.com>
>>>> ---
>>>>
>>>> RFC->v1 - Added devicetree support - https://patchwork.ozlabs.org/patch/604113/
>>>>
>>>>  drivers/net/phy/ti.c | 81 ++++++++++++++++++++++++++++++++++++++++++++++------
>>>>  1 file changed, 73 insertions(+), 8 deletions(-)
>>>>
>>>> diff --git a/drivers/net/phy/ti.c b/drivers/net/phy/ti.c
>>>> index c3912d5..e91a6ed 100644
>>>> --- a/drivers/net/phy/ti.c
>>>> +++ b/drivers/net/phy/ti.c
>>>> @@ -6,6 +6,14 @@
>>>>   */
>>>>  #include <common.h>
>>>>  #include <phy.h>
>>>> +#include <linux/compat.h>
>>>> +#include <malloc.h>
>>>> +
>>>> +#include <fdtdec.h>
>>>> +#include <dm.h>
>>>> +#include <dt-bindings/net/ti-dp83867.h>
>>>> +
>>>> +DECLARE_GLOBAL_DATA_PTR;
>>>>  
>>>>  /* TI DP83867 */
>>>>  #define DP83867_DEVADDR		0x1f
>>>> @@ -57,6 +65,17 @@
>>>>  #define MII_MMD_CTRL_INCR_RDWT	0x8000 /* post increment on reads & writes */
>>>>  #define MII_MMD_CTRL_INCR_ON_WT	0xC000 /* post increment on writes only */
>>>>  
>>>> +/* User setting - can be taken from DTS */
>>>> +#define DEFAULT_RX_ID_DELAY	DP83867_RGMIIDCTL_2_25_NS
>>>> +#define DEFAULT_TX_ID_DELAY	DP83867_RGMIIDCTL_2_75_NS
>>>> +#define DEFAULT_FIFO_DEPTH	DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
>>>> +
>>>> +struct dp83867_private {
>>>> +	int rx_id_delay;
>>>> +	int tx_id_delay;
>>>> +	int fifo_depth;
>>>> +};
>>>> +
>>>>  /**
>>>>   * phy_read_mmd_indirect - reads data from the MMD registers
>>>>   * @phydev: The PHY device bus
>>>> @@ -134,16 +153,58 @@ static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
>>>>  		phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
>>>>  }
>>>>  
>>>> -/* User setting - can be taken from DTS */
>>>> -#define RX_ID_DELAY	8
>>>> -#define TX_ID_DELAY	0xa
>>>> -#define FIFO_DEPTH	1
>>>> +#if defined(CONFIG_DM_ETH)
>>>> +/**
>>>> + * dp83867_data_init - Convenience function for setting PHY specific data
>>>> + *
>>>> + * @phydev: the phy_device struct
>>>> + */
>>>> +static int dp83867_of_init(struct phy_device *phydev)
>>>> +{
>>>> +	struct dp83867_private *dp83867 = phydev->priv;
>>>> +	struct udevice *dev = phydev->dev;
>>>> +
>>>> +	dp83867->rx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
>>>> +				 "ti,rx_int_delay", DEFAULT_RX_ID_DELAY);
>>>> +
>>>> +	dp83867->tx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
>>>> +				 "ti,tx_int_delay", DEFAULT_TX_ID_DELAY);
>>>> +
>>> this is not aligned with the binding you sent.
>>> ti,rx-internal-delay
>>> and
>>> ti,tx-internal-delay
>> You are right I will fix it and then make the same change in the kernel
> Why not just follow linux binding?
> Changing binding in kernel will end up in deprecated binding for nothing.

What specific Linux binding are you referring to?

I don't see this binding getting changed as the internal delay and fifo depth
are board configurable options and I don't for see the register map changing for this
device.

Dan


> Thanks,
> Michal
>
>


-- 
------------------
Dan Murphy