[U-Boot] [PATCH] arm: socfpga: Add samtec VIN|ING board

[Marek Vasut <marex@denx.de>]

On 04/28/2016 02:57 AM, Tom Rini wrote:
> On Thu, Apr 28, 2016 at 01:49:38AM +0200, Marek Vasut wrote:
>> On 04/13/2016 11:53 PM, Dinh Nguyen wrote:
>>> On 04/13/2016 07:24 AM, Marek Vasut wrote:
>>>> Add support for board based on the popular Altera Cyclone V SoC.
>>>> This board has the following properties:
>>>>  - 1 GiB of DRAM
>>>>  - 1 Gigabit ethernet
>>>>  - 1 USB gadget port
>>>>  - 1 USB host port with an on-board hub
>>>>  - 2 QSPI NORs connected to the Cadence QSPI core
>>>>  - Multiple I2C EEPROMs and one I2C temperature sensor
>>>>
>>>> Signed-off-by: Marek Vasut <marex@denx.de>
>>>> Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
>>>> Cc: Chin Liang See <clsee@altera.com>
>>>> ---
>>>
>>> [snip]
>>>
>>>> --- /dev/null
>>>> +++ b/include/configs/socfpga_vining_fpga.h
>>>> @@ -0,0 +1,246 @@
>>>> +/*
>>>> + * Copyright (C) 2015 Marek Vasut <marex@denx.de>
>>>> + *
>>>> + * SPDX-License-Identifier:	GPL-2.0+
>>>> + */
>>>> +#ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
>>>> +#define __CONFIG_SAMTEC_VINING_FPGA_H__
>>>> +
>>>> +#include <asm/arch/base_addr_ac5.h>
>>>> +
>>>> +/* U-Boot Commands */
>>>> +#define CONFIG_SYS_NO_FLASH
>>>> +#define CONFIG_DOS_PARTITION
>>>> +#define CONFIG_FAT_WRITE
>>>> +#define CONFIG_HW_WATCHDOG
>>>> +
>>>> +#define CONFIG_CMD_ASKENV
>>>> +#define CONFIG_CMD_BOOTZ
>>>> +#define CONFIG_CMD_CACHE
>>>> +#define CONFIG_CMD_DFU
>>>> +#define CONFIG_CMD_DHCP
>>>> +#define CONFIG_CMD_EEPROM
>>>> +#define CONFIG_CMD_EXT4
>>>> +#define CONFIG_CMD_EXT4_WRITE
>>>> +#define CONFIG_CMD_FAT
>>>> +#define CONFIG_CMD_FS_GENERIC
>>>> +#define CONFIG_CMD_GREPENV
>>>> +#define CONFIG_CMD_LED
>>>> +#define CONFIG_CMD_MII
>>>> +#define CONFIG_CMD_MMC
>>>> +#define CONFIG_CMD_PING
>>>> +#define CONFIG_CMD_USB
>>>> +#define CONFIG_CMD_USB_MASS_STORAGE
>>>> +
>>>
>>> With my patch[1], you don't need all of those common configs, all you
>>> need is:
>>>
>>> #define CONFIG_CMD_DFU
>>> #define CONFIG_CMD_USB
>>> #define CONFIG_CMD_USB_MASS_STORAGE
>>
>> Well since there are changes in that, are you fine if I pick this board
>> as-is for next ?
> 
> You, or anyone else, picking up "old" board ports

This is a new board port, about two weeks old. Technology is moving fast
nowadays ;-)

> to apply now need to
> either ask people to re-spin the series or run moveconfig yourself to
> make sure that everything (except CMD_NAND) in cmd/Kconfig is done in
> the defconfig and not the config.h file.  For example, those last 3
> Kconfig'd right now.

CMD_EEPROM and CMD_LED are not I believe. Do you have any example of the
moveconfig , so I can try it ?


-- 
Best regards,
Marek Vasut