[U-Boot] [PATCH 1/2] spl: Make sure destination address is dma aligned when loading fit

[Lokesh Vutla <lokeshvutla@ti.com>]

On Wednesday 06 April 2016 05:32 PM, Lokesh Vutla wrote:
> Peripherals like spi etc. uses DMA for transfers. So, when loading the fit
> image the destination address should be dma aligned.

After the v5 of my FS support for FIT[1], this patch is no more
necessary. Patch 2 is alone sufficient.

[1] http://patchwork.ozlabs.org/patch/618403/

Thanks and regards,
Lokesh

> 
> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> ---
> - Assuming u-boot.bin load addr will always be dma aligned.
> 
>  common/spl/spl_fit.c | 11 +++++++----
>  1 file changed, 7 insertions(+), 4 deletions(-)
> 
> diff --git a/common/spl/spl_fit.c b/common/spl/spl_fit.c
> index 4c9fe7b..20396b9 100644
> --- a/common/spl/spl_fit.c
> +++ b/common/spl/spl_fit.c
> @@ -91,7 +91,7 @@ int spl_load_simple_fit(struct spl_load_info *info, ulong sector, void *fit)
>  	void *load_ptr;
>  	int fdt_offset, fdt_len;
>  	int data_offset, data_size;
> -	int base_offset;
> +	int base_offset, align_len;
>  	int src_sector;
>  	void *dst;
>  
> @@ -117,7 +117,9 @@ int spl_load_simple_fit(struct spl_load_info *info, ulong sector, void *fit)
>  	 * In fact the FIT has its own load address, but we assume it cannot
>  	 * be before CONFIG_SYS_TEXT_BASE.
>  	 */
> -	fit = (void *)(CONFIG_SYS_TEXT_BASE - size - info->bl_len);
> +	align_len = ARCH_DMA_MINALIGN - 1;
> +	fit = (void *)((CONFIG_SYS_TEXT_BASE - size - info->bl_len -
> +			align_len) & ~align_len);
>  	sectors = (size + info->bl_len - 1) / info->bl_len;
>  	count = info->read(info, sector, sectors, fit);
>  	debug("fit read sector %lx, sectors=%d, dst=%p, count=%lu\n",
> @@ -173,8 +175,9 @@ int spl_load_simple_fit(struct spl_load_info *info, ulong sector, void *fit)
>  	/*
>  	 * Read the device tree and place it after the image. There may be
>  	 * some extra data before it since we can only read entire blocks.
> +	 * And also align the destination address to ARCH_DMA_MINALIGN.
>  	 */
> -	dst = load_ptr + data_size;
> +	dst = (void *)((load + data_size + align_len) & ~align_len);
>  	fdt_offset += base_offset;
>  	count = info->read(info, sector + fdt_offset / info->bl_len, sectors,
>  			   dst);
> @@ -188,7 +191,7 @@ int spl_load_simple_fit(struct spl_load_info *info, ulong sector, void *fit)
>  	 * After this we will have the U-Boot image and its device tree ready
>  	 * for us to start.
>  	 */
> -	memcpy(dst, dst + fdt_offset % info->bl_len, fdt_len);
> +	memcpy(load_ptr + data_size, dst + fdt_offset % info->bl_len, fdt_len);
>  
>  	return 0;
>  }
>