[U-Boot] [PATCH 1/3] serial: 16550: Add getfcr accessor

[Marek Vasut <marex@denx.de>]

On 06/10/2016 02:34 AM, Simon Glass wrote:
> Hi Marek,

Hi,

> On 26 May 2016 at 12:39, Marek Vasut <marex@denx.de> wrote:
>> Add function which allows fetching the default FCR register setting
>> from platform data for DM , while retaining old behavior for non-DM
>> by returning UART_FCRVAL.
>>
>> Signed-off-by: Marek Vasut <marex@denx.de>
>> Cc: Tom Rini <trini@konsulko.com>
>> Cc: Simon Glass <sjg@chromium.org>
>> ---
>>  drivers/serial/ns16550.c | 20 +++++++++++++++++---
>>  include/ns16550.h        |  1 +
>>  2 files changed, 18 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c
>> index c6cb3eb..b39ce02 100644
>> --- a/drivers/serial/ns16550.c
>> +++ b/drivers/serial/ns16550.c
>> @@ -120,6 +120,13 @@ static int ns16550_readb(NS16550_t port, int offset)
>>         return serial_in_shift(addr + plat->reg_offset, plat->reg_shift);
>>  }
>>
>> +static u32 ns16550_getfcr(NS16550_t port)
>> +{
>> +       struct ns16550_platdata *plat = port->plat;
>> +
>> +       return plat->fcr;
>> +}
>> +
>>  /* We can clean these up once everything is moved to driver model */
>>  #define serial_out(value, addr)        \
>>         ns16550_writeb(com_port, \
>> @@ -127,6 +134,11 @@ static int ns16550_readb(NS16550_t port, int offset)
>>  #define serial_in(addr) \
>>         ns16550_readb(com_port, \
>>                 (unsigned char *)addr - (unsigned char *)com_port)
>> +#else
>> +static u32 ns16550_getfcr(NS16550_t port)
>> +{
>> +       return UART_FCRVAL;
>> +}
>>  #endif
>>
>>  int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate)
>> @@ -170,7 +182,7 @@ void NS16550_init(NS16550_t com_port, int baud_divisor)
>>         serial_out(0x7, &com_port->mdr1);       /* mode select reset TL16C750*/
>>  #endif
>>         serial_out(UART_MCRVAL, &com_port->mcr);
>> -       serial_out(UART_FCRVAL, &com_port->fcr);
>> +       serial_out(ns16550_getfcr(com_port), &com_port->fcr);
>>         if (baud_divisor != -1)
>>                 NS16550_setbrg(com_port, baud_divisor);
>>  #if defined(CONFIG_OMAP) || \
>> @@ -191,7 +203,7 @@ void NS16550_reinit(NS16550_t com_port, int baud_divisor)
>>         serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);
>>         NS16550_setbrg(com_port, 0);
>>         serial_out(UART_MCRVAL, &com_port->mcr);
>> -       serial_out(UART_FCRVAL, &com_port->fcr);
>> +       serial_out(ns16550_getfcr(com_port), &com_port->fcr);
>>         NS16550_setbrg(com_port, baud_divisor);
>>  }
>>  #endif /* CONFIG_NS16550_MIN_FUNCTIONS */
>> @@ -262,7 +274,7 @@ static inline void _debug_uart_init(void)
>>                                             CONFIG_BAUDRATE);
>>         serial_dout(&com_port->ier, CONFIG_SYS_NS16550_IER);
>>         serial_dout(&com_port->mcr, UART_MCRVAL);
>> -       serial_dout(&com_port->fcr, UART_FCRVAL);
>> +       serial_dout(&com_port->fcr, ns16550_getfcr(com_port));
> 
> The debug UART does not have platdata, so I don't think this will
> work.

Hrm, true. If you have DM_SERIAL enabled and debug uart enabled,
this will likely fail.

> For the debug UART perhaps you can use the default value. If
> not, then I think the only option is a new debug UART Kconfig.

I don't use the debug uart, so I don't need the Kconfig option.


-- 
Best regards,
Marek Vasut